Search Documents

By D. Brosnahan, J. Gathje

Newmont Metallurgical Services (NMS) recently acquired a Scanning Electron Microscope (SEM) with a JKMRC/FEI Mineral Liberation Analyzer (MLA). With the MLA software package, raw particle image and X-ray data can be converted into particle mineral maps and bulk and liberation data can then be calculated for minerals of interest. This type of quantitative mineralogical data can then be used for a wide variety of applications. Ore characterization with MLA can be carried out for existing or processing plants in development. MLA characterization of laboratory test products provides valuable liberation information that assists the research metallurgist in better planning and developing process treatment options for various ore types. This paper describes the use of MLA characterization in a copper flotation test program where the use of various testing options for arsenic depression was being evaluated.

Jan 1, 2007

By Andrew K. hg` Officer, A. L. Griffiths, J. Andrew Hindmarch, Gert Wittneben

Durban Harbour in South Africa is one of the continent’s busiest ports however the harbor entrance is currently too small for the new generation of container ships. There-fore it is to be deepened and widened by the National Ports Authority in the near future. An existing immersed tube tunnel carrying major sewer, water and other utilities under the harbor first needs to be removed and replaced by a deeper 4.4 m ID ser-vices tunnel. Construction of the deeper tunnel saw the first use of a slurry machine in South Africa and was required to negotiate grades up to 20%.

Jan 1, 2007

By Dick T. Atkinson

This report describes the Foster-Miller program that designed, developed, built and tested an automatic, remote control mine car coupler. This new coupler gives the motorman the capability to selectively couple and uncouple cars from the locomotive, to transmit braking intelligence to the coupled car s and to determine if the trip is intact. Hazards due to derailment and runaway cars will be reduced as the brakes are automatically applied in any uncoupled car. Laboratory tests described herein have been completed on the coupler set. Applications include, but are not limited to, the unit train system.

Jan 1, 1976

By Fidelis T. Suorineni

Rapid drifting enables quicker access to orebodies, higher production rates and a resultant reduction in production cost. The Mining Innovation, Rehabilitation and Applied Research Corporation (MIRARCO) funded by the Canadian Mining Industry Research Organization (CAMIRO) has developed a methodology for safe rapid drift development within the underground metalliferrous mining industry in Canada According to industry survey, about 36% of drift development cycle time is spent on support installation. MIRARCO has developed a methodology for safe rapid drift development based on minimizing time spent on support installation. The methodology includes a critical review of the rockmass classification systems, examination of current support practices in the mining industry and civil tunneling, review of rapid drift development practice in South Africa, introduction of risk hazard procedures to account for material property variability and the development of a WIZARD as a quick decision-making tool for the implementation of the procedures. A comprehensive field data collection procedure was put in place and data collected from various mines to verify and calibrate the support selection rationale. The findings of the research programme resulted in the development of an improved rockmass classification system and showed that construction effects have drastic influence on support levels but is often not accounted for in assessing support levels. Stress effects and structurally controlled failures are the other important factors to take into account in rapid drift development. Three support classes were established for safe rapid drift development as No Systematic Support, Light Support and Strong Support. The support levels took into account cost, rate of installation and safety based on compatibility with ground characteristics. This paper describes the methodology for safe rapid drifting within the underground metalliferrous mining industry in Canada and highlights the key issues and major drivers behind their continued development at the Geomechanics Research Centre within MIRARCO.

May 1, 2004

By R. Luchese de Moraes, J. A. Matthews, C. Feliciano Bruzual

The role of biomass char in blast furnaces has been re-examined by scientists worldwide, as a feasible option to reduce the carbon intensity of ironmaking. This contribution makes a technical and economic analysis of the ferro gusa industry in Brazil, with the last 172 charcoal-Blast Furnaces operating in the world. A key strategic question is presented: what is the current status and future prospects of biomass use in Blast Furnaces? Findings provide significant implications to metallurgists: while ferro gusa from charcoal is regarded as carbon neutral iron with low impurities, there are limiting factors that hinder the further proliferation of charcoal-BFs: biomass generation requires vast extensions of arable land and aggregates have low production capacity. Additionally, most of the charcoal is presently generated in beehive kilns with low yields. These elements combined make charcoal-hot metal expensive in price. With respect to the future prospects of biomass, the injection of small biochar particles through the PCI rigs in BFs (here coined Bio-PCI) and iron ore sintering may offer a practical alternative to significantly reduce the CO2 emissions in the ironmaking process.

Jan 1, 2015

By Masaki Kitazume

"Abstract The wet type and dry type of deep mixing methods have been developed and widely applied for on-land and marine constructions in Japan. The quality assurance (QA) of the methods has been usually carried out by unconfined compression test on field stabilized soil sampled by core boring in Japan. In some other countries, stabilized soil excavated by the wet grab sampling instead of core sampling is often subjected to unconfined compression test for quality assurance. There are several merits and demerits in each method, but few studies have been carried out to compare the stabilized soil strength of these two types of specimens to discuss their applicability to practical construction. The author has conducted a series of field and laboratory tests to compare the stabilized soil strength and discuss the applicability of wet grab sampling to QA for wet and dry types of deep mixing method.In this study, the wet grab sampling was carried out at two road embankment construction sites where the wet type and dry type of deep mixing were applied. The cement stabilized soil was excavated at the three depths by a wet grab sampler soon after the DM column construction. The test result is compared with the other test data in the previous study to discuss the applicability of the web grab sampling method for QA of cement stabilized soil.IntroductionThe Deep Mixing Method (DMM), an in-situ soil stabilization technique using cement and/or lime as a binder, is often employed to improve soft soils (Kitazume and Terashi, 2013). A variety of factors and their interactions affect the eventual strength of a deep-mixed column, while some of which are controllable (e.g. binder type and dose) by engineers while the others are not (e.g. soil types, ground temperature, etc.; Babasaki et al., 1997). In addition to laboratory mix tests, which in essence are a parametric study to estimate the influence of these factors on a particular soil’s strength, the quality assurance (QA) practice in Japan usually involves unconfined compression test on sampling cores from the stabilized columns after a given curing period. It has been recognized, however, that the ‘field strength’, or the strength of the retrieved core, quf is on average lower than the ‘laboratory strength’, qul, evaluated by laboratory mix test. Also allowing for the inevitable variability, existing guidelines (for example, PWRC, 2004 and CDIT, 2008) recommend the design quf /qul values of, for example, 0.5-1.0 for the CDM (Cement Deep Mixing; a wet-type technique, in which binder is added as slurry) and 0.2-0.33 for the DJM (Dry Jet Mixing; a dry-type technique, in which binder is added as powder)."

Jan 1, 2014

By C. M. K. Boldt

Between 1989 and 1991, the greatest number of accidents in surface coal and metal/nonmetal mines involved haulage trucks. In 1995, the most frequently cited factor contributing to the 100 fatalities in these mines was powered haulage. In 1996, over 50% of the 84 Fatalities in mining that year were in surface mining. Because some of the world's largest mobile equipment is used in surface mines, and this equipment is involved in so many accidents and fatalities, new technologies are needed to alert truck drivers and people in spaces around the truck to the possibilities of collisions.

Jan 1, 1999

By S. Boone, J. N. Shirlaw

INTRODUCTION Soft, near normally consolidated clays generally provide ideal conditions for tunneling using Earth Pressure Balance (EPB) shields. It is easy to turn the clay into a low permeability, viscous spoil that can be pressurized to maintain the required face pres-sure. Despite this, there are records of relatively large, and often quite variable, surface settlements over EPB driven tunnels in soft clay. To understand this variation it is necessary to identify the various factors that contribute to settlement. Tunnels in soft clay are ideal for study these effects in the field, as an unsupported void will close almost immediately, due to the low shear strength of the soil. In the short term, deformation in a soft clay will occur at constant volume, so short term surface settlements can be related to movements at tunnel level. In this paper, data will be used from EPB driven tunnels in Singapore marine clay. In all of the cases discussed the lining consisted of precast concreted segmental rings erected in the tail of the shield. The marine clay in Singapore has been studied, among others, by Tanaka et al.(2001). The clay typically has a plasticity index of 40 to 60, and the undrained shear strength (SU ) can be derived from: SU = 0.22 svo' where svo' is the current vertical effective stress. Figure 1 shows a summary of undrained strength/depth plots used for design on two sections of Singapore’s North East Line. The stability of a tunnel in clay can be assessed by comparing the stability number (N) of the tunnel with the stability number at total collapse (NTC). The stability number can be calculated from the equation: N = (?Z + q – Pt)/SU where: ? = the average unit weight of the ground above the springline of the tunnel Z = the depth to the springline of the tunnel from the ground surface q = the surcharge Pt = the support pressure within the tunnel The stability number at total collapse depends on the size, geometry and depth of the tunnel, and typically ranges between 5 and 9. Charts for assessing the number at total collapse are provided in Kimura and Mair (1981), based on the testing of model tunnels in a geotechnical centrifuge. For tunnels in the Singapore marine clay, the stability number of an unsupported tunnel would be over nine if the tunnel ois more than 8m deep. As a result, a support pressure

Jan 1, 2007

By A. El-Midany

Dolomite impurities are increasing in the currently mined phosphate deposits in Florida. Several research efforts have been conducted in various laboratories around the globe to find methods to economically removing the dolomite. However, a universal and cost-effective process is not now in commercial use. In this paper, a new process for dolomite/apatite separation is presented. The differential solubility of dolomite in slightly acidic solution is utilized to generate micro CO2 bubbles at the dolomite/water interface. Particle (dolomite)/bubble aggregates float to the surface leaving phosphate concentrate with low MgO content. Interestingly, up to 6.0 mm particles can be floated by such micro-bubble/particle aggregates. Different surface-active agents were tested to stabilize the bubbles. Results of these tests are presented, and the mechanisms involved are discussed.

Jan 1, 2009

By Roger A. Dworak

This report describes in detail the work done on the development of the Time Domain Reflectometry Microcomputer (TDRM). Modifications to the FMC-Model 302A Cable Fault Locator is described in Appendix D. The TDRM unit uses an 8080 microcomputer to accurately locate major faults in low capacitance cables to within ± 1 foot when properly calibrated. Major faults in high capacitance cables are usually located within ± 5 feet. The upper limits of fault detection are <1 kilohm shunt fault and >7 ohm series fault. In practice fault detection limits are reduced to <300 ohms shunt fault and >30 ohms series fault because of discontinuities caused by cable repair.

Jan 1, 1977

The first principle one usually Learns about blasting is that cunpetence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced blaster when operating in a new area, may have to make one or two shots just to acclimate himself to the new conditions with which he is faced.

Jan 1, 1989

By Peter Zhang

Shield recovery in a longwall move is normally conducted from tailgate to headgate. However, if the face is wide and the immediate roof is weak, difficult conditions with considerable roof sag, excessive shield load, and local roof falls could occur as the shield recovery proceeds to the middle of the face, causing delays in shield recovery. The situation could be aggravated when a pre-driven longwall recovery room is employed. Alternatively, a bi-directional approach for shield recovery, i.e. shield recovery starting from the middle of the face towards both tailgate and headgate, can alleviate the roof sag significantly by quickly withdrawing the shields towards the lower abutment pressure zones at the headgate and tailgate sides. In this case, the bi-directional shield recovery approach was used in a longwall move for a 1450 ft wide face under weak roof conditions. Shields were successfully withdrawn within five days without experiencing significant roof sag. The time-dependent roof-to-floor convergence, shield pressure, and roof conditions were monitored during shield recovery. 3-D finite element modeling was conducted prior to longwall move to evaluate the difference between a uni-directional and a bi-directional shield recovery during a longwall face move. Vertical stress, yield zone in and around the recovery room, load on the shields, and convergence at the center of the shield canopy were obtained from computer modeling, and compared with the data from field monitoring. Finally, the advantages of the bi-directional shield recovery are discussed.

Jan 1, 2007

By Mark R. Svinkin

Construction vibrations may adversely affect surrounding buildings and their effects range from human discomfort and disturbance of sensitive devices to visible structural damage. There is no unique conclusion regarding the effect of construction vibrations at every site. Measurement is usually made to monitor vibrations and control them with the vibration thresholds for disturbance of sensitive objects as well as damage to structures. To prevent potential litigation and mitigate the vibration effects on sensitive devices, people and structures, it is necessary to manage and minimize vibration problems before the beginning of construction activities or installation of vibrating machine foundations, and during construction. Pre-construction damage survey and engineering vibration investigations, including the prediction of anticipating vibrations, have to be made at most construction sites in advance of construction activities. Vibration monitoring and control have to be provided during construction. The instrumentation feedback of vibration prediction, monitoring and control provide the basis for choice of measures to prevent or mitigate vibration problems and settlement damage hazards.

Jan 1, 2002

By C. Sawmliana, P. Pal Roy

Near-field blast vibration response of restrained pipelines either buried or exposed was studied during rock excavations at sensitive locations for Stage-II (4x500 MW) commissioning work in a super thermal powerplant of the National Thermal Power Corporation Ltd. (NTPC) of India. The existing running plant of capacity 1000 MW has many important installations including pipelines of varying diameters. These pipelines were very close to the blasting locations (mostly within 12m). Blast optimization and consequent monitoring of vibrations were carried out simultaneously for more than 250 experimental blasts conducted by the authors. This paper emphasized, particularly, on the safety of pipelines and their responses due to repeated blasting impacts. A few guidelines supported by theoretical derivations are provided for futuristic research.

Jan 1, 2001

By J. D. Findlay

The demands on development in London in recent years has led to the increasing use of top down construction methods in which there is a requirement to place steel columns to high tolerances into large diameter bored piles with deep cut-offs. A number of different proposals for the sequence of construction are being suggested. The tolerances requires for the steel columns are becoming increasingly stringent. This review examines a number of basic construction proposals and comments on the problems and solutions used by foundation contractors to provide the required foundations.

Jan 1, 1989

Unrelieved residual strains can influence the states of stress in rock masses. If cheap, stable structures are to be constructed in Tock in which large pressures are exterted by unrelieved residual strains, the pressures must be either utilized or neutralized. A photoelastic technique has been used to show that the release of residual strains in rocks is influenced by the mechanical properties of anisotropic rock fabrics. The relationships between directions of residual strain release and the attitudes of minor geological structures have been determined. For engineering design purposes it is possible to estimate the principal stress directions in rock containing unrelieved residual strains if the attitudes of such minor geological structures as foliation planes, lineations, and joints are known.INTRODUCTIONQuarry workers have long been aware that near-surface rocks may be highly stressed. In many cases the stresses are too large to be the result of gravitational loads. Dale (1923, pp. 34-35) gives many instances of deformation produced by the violent release of residual strains in quarry rocks. Coates (1963) has described powerful rock bursts and cases of rock deformation underground implying the existence of much larger stresses than are likely to result from present-day gravitational loads. The only explanation is that pressures of up to several thousands of pounds per square inch may be caused by unrelieved residual strains in rock.Instruments have been developed for measuring states of stress in rock masses. Most stress determinations in rock have been made on the assumption that rock behaves as a simple elastic material. It is now known that rock is a...

Jan 1, 1964

By A Giblett, R Dunne, D Appelhans

There are a number of hurdles that must be negotiated in order to design an effective gold ore treatment facility such that the expectations forming the basis of project economics are valid and can be achieved in practice. Selecting samples based on geometallurgical context, performing and interpreting testwork relevant to the selected process flowsheet are essential considerations towards achieving this aim. This paper discusses recent experiences in process development for free milling gold ores giving consideration to frequently encountered challenges of this nature.CITATION:Giblett, A, Appelhans, D and Dunne, R, 2013. Considerations for effective gold process development, in Proceedings MetPlant 2013 , pp 445-454 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Howard B. Hamilton

Laboratory performance of mercury filled current limiting devices (CLD) used for high speed switching of DC circuits (600 volts and below, up to 1000 amperes) using a system involving a parallel connected vacuum switch with CLD and an additional series connected vacuum switch was verified in USBM Contract #HO 357079. This report details analytical work and field experimental tests to predict and control voltage surges associated with the high switching speed associated with the switching system. It also details tests conducted to demonstrate the fault current limiting ability of the CLD. Problems associated with designing a fault current limiting system are discussed.

Jan 1, 1978

By Benoit Virollet

Over the last 10 years the diameter of unbraced, unlined and unanchored circular shafts has grown dramatically in many parts of the world. This progress has taken place through improvements in: construction methods; concrete rheology; and design capabilities. Excavation equipment has become more precise in terms of operator control and ability to correct alignment of digging elements leading to better alignment tolerances. Also contributing to the increases in shaft diameters is the evolution of design models. A better understanding of soil structure interaction is being incorporated into the analyses in terms of radial soil stresses and imposed loads on the shaft. This paper provides an overview of the recent progress made in circular shaft construction, the primary design considerations, and some innovative uses of efficient arc elements to develop unsupported structures of other shapes. In addition, a summary of recent circular shafts constructed worldwide is provided.

Jan 1, 2006

OZ Minerals Limited owns and operates the Prominent Hill Copper-Gold Mine, located 140 km southeast of Coober Pedy in far north South Australia. The Prominent Hill mine comprises an open cut mine with an initial 10 year mine-life and an 8 Mtpa conventional grinding and flotation plant to produce high quality copper-gold-silver concentrates, which are exported by road to local customers and by rail to the port of Darwin for shipment on to Southeast Asian smelters. Mine and process operations at Prominent Hill are licensed to abstract a water supply of up to 26 ML/d, sourced from a borefield located 40 km and extending to 80 km east of the mine. The arid climate of the broader Prominent Hill region means that groundwater is important for sustaining community and pastoral industries in the region, and security of water rights for third party users is a critically important water management issue posing a significant challenge to the development of Prominent Hill. Depth to water table and the typically high salinity of groundwater in the region means there is little environmental dependence on groundwater within the immediate Project area (mine lease and wellfields). The Prominent Hill mine and associated infrastructure lies within the South Australian Far North Prescribed Wells Area (FNPWA), which was principally defined to ensure the ongoing security of the ecologically, socially and culturally significant GAB springs, of which the closest are found around 150 km northeast of Prominent Hill, and only 50 km northeast of the water supply borefield. Prescribing of the FNPWA meant that OZ Minerals was required to demonstrate to both State and Federal Government agencies that the mine&apos;s water supply is independent of that which supports GAB springs and other third party water users in the region. Recognising these potential obstacles, OZ Minerals successfully defined and developed a previously unknown industrial quality groundwater resource, separate from other important groundwater resources in the region that supply community, pastoral and environmental users, ensuring third party water user sustainability.

Jun 1, 2010