Search Documents

By I. Liebman

Two triggered barrier systems and several extinguishing agents were tested against coal dust explosion propagating in the main entry of the Bureau of Mines Experimental Mine at Bruceton, Pa. One system used a high-pressure cylinder to propel the extinguishant; the second system used pressurized nitro-gas or Halon 1301 (CF3Br) in a low-pressure system to power the disperser. The relative efficiencies of the extinguishants were determined by compar¬ing calculated concentrations of the extinguishant clouds present in the mine during suppressing of the explosions. Results showed the following trend of increasing effectiveness: Purple-K (KHC03)<water<hybrids consisting of foam or water combined with Halon 1301<Halon alone. On a weight basis, water was two to three times as efficient as Purple-K, whereas the hybrids and Halon alone were only marginally superior to water. Maximum efficiency of an extinguishant is attained by high rates of discharge from the barrier and by minimizing the time interval between onset of discharge and flame arrival to that necessary for discharge. Both the high- and low-pressure barrier systems were demonstrated to be capable of suppressing coal dust explosions; however, because of the potential hazard of the former, the low-pressure system is considered to be the most attractive prototype.

Jan 1, 1979

By Günther M. Volkmann

Continuous developments in tunneling require knowledge transfer between designers and suppliers to optimize the application of support systems. This collaboration allows the designer access to the latest research results, technical innovations, and support specific measurement techniques as well as the supplier?s experiences on recent projects. Project specific requirements determine the information that can be used to increase support system efficiency, advance rate, degree of safety, or decrease costs. This cooperative effort results in not only an unambiguous tender document, but also an optimized design with reduced risk that is coordinated with safe and high performance construction techniques. This paper will address the benefits of an early collaboration to both the design and the specifications in the tender document by using the A3 Hindhead project (UK) as an example.

Jan 1, 2008

By D. Goossens

Quality control is a system which should guarantee that quality is achieved. It is the execution and verification of a project in an organised way, in order to obtain the maximum of certainty that the results meet the requirements. This concerns all stages of the project, from the soil investigation, over the design, to the execution. Quality control can and has been successfully realised for important projects by means of a quality plan. A quality plan is based on a number of general considerations, but should certainly be focussed on the particularities of a specific project. Practical examples of quality plans, which have been realised on sites in Belgium, are developed and the advantage of the system is shown by concrete case studies.

Jan 1, 1996

By R. C. Ellman

Since successful industrial lignite-burning equipment was developed in 1925, the commercial use of lignite as a fuel for power plants has increased. It has proved an entirely satisfactory fuel for generating power and can be burned efficiently by various methods.4/ Equipment to fire pulverized lignite was installed and used successfully at the Trinidad Station of the Texas Power & Light Co. as early as 1926. The lignite was predried in steam-heated grid driers before pulverizing.5/ This method of firing was used later in the Comal Station of the San Antonio Public Service Commission.6/ Both stations, however, have since been converted to use other fuels. Units for pulverizing and drying lignite are relatively new in the lignite-consuming region of North Dakota. The air which sweeps the pulverizer and transports the pulverized product to the burners is preheated to dry the lignite during pulverization. The first unit was installed in 1948 in one of the two boiler units of the Crookston Station, Otter Tail Power Co., Crookston, Minn.7/ In 1951 the 30,000-kw. W. J. Neal Station, Central Power Electric Cooperative, Inc., Voltaire, N. Oak., was designed and constructed for firing pulverized lignite exclusively. It is the largest lignite-fired, power-generating station in North Dakota. The 44,000-kw. Lewis and Clark Station of the Montana-Dakota Utilities Co., Sidney, Mont., is fired by a similar pulverizing system. Operation of this plant was begun in October 1958. At Fergus Falls, Minn., the 53,500-kw. Hoot Lake Station of the Otter Tail Power Co., also using a pulverized lignite-firing system, began operating in September 1959.

Jan 1, 1961

By W. E. Robinson

Differences in the composition or chemical structure of the organic material in samples of Uinta Basin (Utah) oil shale were studied relative to stratigraphic position within the Green River Formation. This involved a systematic study of the soluble organic material and the insoluble organic material (kerogen) present in the samples. Emphasis was placed upon the distribution of the alkanes (normal and isoprenoid compounds) in the soluble extracts and upon the aromaticity of the kerogen. Significant differences exist in the chemical composition of the organic material from various strata within the Uinta Basin, some of which were related to burial depth but most were related to source material variations, environmental differences, or other factors. The Uinta Basin samples differed significantly from Piceance Creek Basin and Green River Basin samples in the large amount of soluble extract they contained.

Jan 1, 1975

The relationship between neural network (NN) performance and the parameters that form the architecture of the neural network is complicated. This paper studies an issue that is still controversial—the effect of the number of neurons and number of hidden layers on NN performance. This paper tests if the above parameters affect network performance when the NN is trained according to the quick stop strategy. It was determined that the number of neurons did not have any effect on the NN performance for a single layer or a double layer network. It was also found that the training error and calibration error could be poor indicators of the prediction correlation coefficient.

Jan 1, 2003

By T. Tamura

It is known that the CaO-FetO-P2O5slag system has a wide liquid miscibility gap at steelmaking temperatures and this two-liquid slag phase has many advantages such as high activities of both FetO and CaO and high amount of P2O5. The phosphorus distribution ratio between the two-liquid slag and molten steel was confirmed to be higher than that between CaOsat.-FetO-P2O5slag and molten steel. The two-liquid slag may be useful for dephosphorization of molten steel and reduction of slag volume. Furthermore, the phase equilibrium of two-liquid CaO-FetO-P2O5slagsaturated with MgO was measured to determine the applicability of the two-liquid slag to dephosphorization in steelmaking process. Keywords: slag, refractories, solid solution, two-liquid phase, dephosphorization, steelmaking, phase equilibrium.

Jan 1, 2004

By R. J. Hickson

From 1993 through 1999 Cyprus Amax Minerals Company successfully completed eight major construction projects around the world. Six greenfield mines were brought into production, an ongoing operation was completely modernized, and an environmental issue was appropriately remediated. The projects stretched over three continents, from arctic Russia to the Atacama Desert, from 16,000feet to sea level, from city suburbs to remote wilderness, from a low of $130 million to over $1 billion. Open pit and underground; mill and leach; gold, copper, molybdenum, and coal were all encompassed. The breadth of diversity experience from these projects inspired Cyprus Amax to create a “best practices” project management protocol, to steer corporate expansion into the next millenium. This paper summarizes those best practices, while high-lighting project management pitfalls to avoid.

Jan 1, 2000

By Walter Valery, Peter Radziszewski

"The NewCrest Cadia operation boasts the largest SAG mill commissioned last June 1998. A request was made to shed some more light on possible SAG mill charge behaviour. Three different software were used to simulate SAG mill charge behaviour:Mishra/Rajamanis MillSoft DEM charge motion program, Radziszewskis agglomerated DEM charge motion program and Powell/Nuricks MillTraj outer trajectories program. The contexts simulated are: 20/30 % charge volume, 65/75/85 % critical speed using the Hi-Lo lifter configuration specified for the mill as well as a Hi-Lo 60 degre lifter face configuration. Further, lifter interval was also studied to determine the effect on power draft. Power predictions are compared with those obtained during the commissioning period.INTRODUCTIONThe NewCrest Cadia operation is located outside of Orange, New South Wales, Australia. With proven reserves of 190 million tonnes at a grade of 0.75 g/t Au, the mill was designed to process 17 Mtpa (2065 tph) of ore with an 86% copper and 73% gold recovery. The grinding circuit (Fig. 1, Table I) boasts the largest SAG mill (Fig. 2) and was commissioned last June 1998."

Jan 1, 1999

By Bratt G. C

When zinc is electrowon from concentrates or residues of high manganese content, the zinc sulphate electrolyte may contain high levels of manganese. The manganese level is usually controlled by removal of manganese at the anode as the dioxide during the zinc electrodeposition stage.By increasing the temperature of an electrolyte containing 8 gll manganese from 35&#176;C to 90&#176;C, decreasing the acidity from 100 gll to 30 gll, reducing the current density from 432.A.m-2 t6 286 A.m-2 and using new lead anodes containing over 0&#183;75 per cent silver, the current efficiency for manganese dioxide removal was .increased from less than 1 per cent to over 20 per cent.At the same time the current efficiency for zinc deposition was maintained above 90 per cent by additions of high molecular weight cationic polyacrylamides to the cell. By utilization of these conditions in a small number of cells, the manganese level in the circuit could be economically concrolled to any desired level.With these conditions the formation of the dioxide changes from an indirect route, via Mn04-, to a direct oxidation of Mn2+ to Mn02.The incorporation of impurities such as Pb, K, NH4, Cu, Ni, or Fe makes the deposit unsatisfactory for direct use in Zn - Mn02 dry cells. The deposit structure changes from cryptomelane at low temperature to y3-Mn02 at high temperature.

Jan 1, 1975

Jan 1, 1970

By F. Dahl, P. Raleigh, J. Holzhauser, B. Nilsen

Tunnel excavation using tunnel boring machines (TBMs), has become increasingly common in recent years, despite the fact that precise evaluation of certain risks have not kept pace with the use of these machines. One of the risks easily overlooked by Engineer and Contractor alike are the effects of abrasive ground on the costs and schedule of a given project. The impacts of worn and damaged TBM cutter heads have been observed on hundreds of tunnel projects around the world. It would appear that a reliable prognosis of the abrasiveness of soils on a project would be of great importance for designers, clients and contractors alike. Several well acknowledged test and prognosis methods already exist for rock, however there is only very limited knowledge available to describe the abrasiveness of soil and its impact on soft ground TBMs. This paper will examine approaches to this problem and suggest a new approach based on a current project undergoing design.

Jan 1, 2007

By William J. Campbell

The purpose of this investigation was to extend the analytical services which are required for Bureau of Mines programs in developing and evaluating high-purity materials. Determination of trace elements in minerals and ores as an aid in geochemical evaluation and prospecting was considered. Serious consideration should be given to the merits of using the avail- able fluorescent X-ray spectrographic instrumentation and techniques for determining trace elements. Limits of detectability for trace elements in metal, oxide, solution or mineral samples range from 0.1 to 100 p.p.m, depending on the element being determined, overall sample composition, and the complexity of the X-ray spectra; limits of detectability range from 0.01 to 1 microgram for elements that have been preconcentrated by a chemical or physical process, for example, by ion-exchange membrane.

Jan 1, 1962

By Kyle Wagner, William Joa, Colter Angell, Catherine Johnson, Marty Langenderfer, David Doucet

The goal of any business is to seek the maximum profitability for the organization through optimization the use of resources, processes and the application of new technologies. An analysis of various case studies demonstrate that blasting can have positive impacts on the crushing and milling processes resulting in increased profitability for the mining industry (Grundstrom, Kanchibotla, Jankovich & Thornton, 2001). This paper describes the case study of two copper mines in Peru producing Cu-Mo and Cu-Au concentrates, which together with their strategic partner, have implemented a project focused on the improvement of rock fragmentation. The project was based on techniques of pattern size reduction, the use of high energy explosives and the technology of electronic initiation. Combined, these techniques were shown to have significantly impacted the efficiency of downstream processes.

Jan 1, 2019

Three large deposits of good quality lignite were located and delineated in the Central Otago region between October 1978 and July 1979. The program was initiated and funded by Mines Division of the Ministry of Energy as part of the national Coal Resource Survey. The exploration work was carried out by Lime and Marble Limited on a contract basis (Bowman, 1980). The three deposits were all potentially mineable by open cast methods and possessed combined indicated and, inferred reserves in the order of 1000 x 106 tonnes. They ranked with the previously discovered Eastern Southland 1ignites and as such constituted an important national energy resource. Fifteen months later a second more detailed investigation of similar duration was undertaken by the Liquid Fuels Trust Board (LFTB). The objective was to upgrade and refine the geological data base of all of the nine South Island 1ignite deposits in order to make preliminary economic assessments of their potential. Again Lime and Marble Limited acted as the exploration operator (Bowman, 1981a, 1981b, 1981c).

Jan 1, 1983

By P. Mills

The four top barite-producing countries in the world are China, India, Morocco and the United States. China is currently the largest exporter of barite followed by India. More than 95 percent of the barite mined today is used by the petroleum industry as driller’s mud. The rest is used in the industrial market and the medical field. Most of the barite mined in the United States is in Nevada. This year, mining activity has increased due to an increase in oil exploration/development. This was caused by an increase in the crude oil prices.

Jan 1, 2005

By L. Mead

Dimension stone is a natural stone (granite, marble, limestone, sandstone and slate) that can be quarried, cut and shaped to conform to acceptable industry standards for size, consistency and durability. There are numerous outlets for the finished product in exterior and interior architectural and design applications. A continued growth market is with residential usage— particularly in new, upscale construction. This has become a competitive market between domestic producers and lower cost imported products. These imported products have become available at many of the building supply retail outlets and have increased the use of stone in residential construction and renovation. The traditional architectural application of dimension stone is tied to commercial and institutional building construction trends and market. There has been a noticeable increased usage of stone in the Sun Belt. This stone is usually supplied by local fabricating shops. It is used in the exterior and interior of shopping malls. This market generally uses local stone sources. It has increased the demand for sandstone, limestone and quartzite in this region of the country.

Jan 1, 2005

By V. B. Dale

This report is one of a series covering the mineral resources of the Nation. It briefly describes most of the known tungsten deposits in Gila, Yavapai, and Mohave Counties, Ariz. Many of the descriptions are taken from the reports of previous examinations by Bureau of Mines engineers, and from Defense Minerals Exploration Administration files. Where a previous examination had been made, and an inquiry disclosed that little or no work had been done since that time, pertinent information from the report was used in this paper with acknowledgment of the source. However, the majority of the descriptions is from field examinations by the author. In the past 3 years (July 1956-May 1959) only necessary annual assessment work was conducted on nearly all the properties described in this paper. There was no active mining on any of the properties examined.

Jan 1, 1961

By Y. Bai, J. J. Liu, D. Q. Li, S. Z. Liu, X. T. Wang

"This paper presents the results of an industrial test using 8 t/d of Baotou concentrate (50% REO) of a clean metallurgical process, which includes: 1. Roasting with H2SO4 at low temperature (220~260 0C) in a batch roasting furnace followed by water leaching to obtain a leach liquor as feed with a yield of >95% RE and Th, recovering F as fluoride, producing a leach residue amounting to 1/3 of an equivalent high temperature residue and containing <0.03% Th and radioactivity < 3×104 Bq/kg compared to the normal high temperature residue containing 0.2-0.3% Th and 1×105 Bq/kg. 2. Separating Th with N1923 and extracting RE by P507 has been completed in mixer-settlers. Test results indicate that the ThO2 product has a purity of > 95% with a yield of 99%, and the RE has a yield of >95%, in which ThO2/REO <5×10-6, and that P507 loaded RE connect straight with separating RE using P507-HCl system. 3. Treatment and multipurpose use of "three wastes" (water, gas and solids) are discussed in some detail."

Jan 1, 2014

By J. Perlacia

"As the bulk handling sector continues its transformation to Industry 4.0, the mining industry, and its harsh working and environmental conditions, provides a perfect spot to study the feasibility of remote analysis and maintenance of the components used for bulk handling. The most important and expensive tools have been adapted to the digital era in recent years, from remotely controlled haul trucks to monitored conveyor belts.However, the big items of the installations rely on smaller parts that have been leftaside, mainly due to the difficultyof adapting them to the Internet ofThings (IoT).The paradigmatic example is the lack of monitored rollers, while all the other components of the conveyorbelt installations (the belt itself, motors, drums, etc.) were monitored some time ago. The main problem is that a failure of a single roller can cause the stoppage of the entire conveyor, due to possible damage to the belt. Thus, the implementation of an integral monitoring system of all the components of the conveyor is a must.The research and development department of ULMA Conveyor Components has been working since early 2012 on the development of monitored rollers, testing all the problems until their final installation in different demanding conditions, from the extreme heat in Australia to the freezing cold of Norway. All the tests have been done under actual working conditions, in real installations and have provided valuable knowledge in the identification of problems, their solutions and the final advantages of a roller monitoring system.Background and current stateThe malfunction of a single roller in certain conveyor belts can force the standstill of the entire installation until its replacement, due to the risk of greater and more expensive failures, such as a rip in the belt. In the case of a bulk handling installation, where a continuous supply of material is necessary, an unexpected stop of one hour could result in huge economic losses."

Nov 1, 2019