Search Documents

By Tianjiao Luo

Some literatures discussed on how to recycle the various reagent, but the discussion on how to reuse the waste liquid directly is very little. How to reuse the waste liquid directly was researched in this paper. Firstly, the waste liquid should be filtrated to remove the impurity; then some quantity of H2O2 solution was dripped into the waste liquid to pretreat it; finally, CuSO4solution was added into the treated waste liquid and the pH was adjusted to about 12, then some HCHO solution was added into the waste liquid, in which the treated carbon fiber can be plated. The morphology and composition of coatings were investigated by means of Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS), the deposition rate was mensurated by the way of dissolution. The results indicated that, the plating effect was basically identical with new plating solution, and the solution is stable, and the plating rate is still about 0.8µm/h, and the copper coating is even and combines closely with carbon fiber. According to this way, the waste liquid can be reuse 5~7 times.

Jan 1, 2006

By Yongbin Yang

Cathodic reduction of oxygen is a process involved in many fields. As is well known, the mechanism of oxygen reduction usually varies considerably with electrode substrates. In this paper, cathodic reduction of oxygen on gold electrode was studied by linear sweep voltammetry with regards to cyanide leaching of gold. As the results shows, the electron transfer number increases as potential shifted negatively and decreases as pH value increases. Besides, the increment of electron transfer number as a function of potential decreases when pH value increases. When pH increases to 13.0, the volt-ampere curve exhibits a relative flat section with currents approximate to the limit current density of a 2e process. By varying dissolved oxygen concentration, the electron transfer number was calculated for pH11.0 at different potentials, the results being 2.387e, 2.732e, 2.982e, and 3.227e at, -0.35V, -0.40V, -0.45V, and 0.50V, respectively. The calculated current densities are in good conformity with measured results.

Jan 1, 2010

By Liu Wei

In order to make clear the dissolving characteristic of the chrysocolla (CuSiO3?H2O) in the ammonia-ammonium chloride solution, a thermodynamic model of the chrysocolla (CuSiO3?H2O)-ammonia- ammonium chloride-water system is established using the exponential computation method based on both mass balance and charge balance equations. The equation group of the thermodynamic model is solved by the MATLAB Soft on PC. The condition which is favorable for dissolving high concentration of copper in solution is making out. The stable area of chrysocolla (CuSiO3?H2O) and the condition of chrysocolla (CuSiO3?H2O) converting to atacamite (Cu(OH)1.5Cl0.5) is also studied. A group of experiments are designed to validate the veracity of the results of the thermodynamic calculation.

Jan 1, 2010

By Murat Alkan

In this study, a self-propagating high-temperature synthesis (SHS) and following acid leaching techniques were carried out to produce boron carbide (B4C) powder. First, B2O3 was obtained through calcinations of H3BO3 at 1073 K for 2 hours. Then, the glassy B2O3 obtained was crushed and sieved. In the SHS experiments, different amounts of B2O3, Mg and C black were used. The SHS product was obtained in the form of black, spongy solid. In the leaching step, the SHS product was leached in a HCl solution to eliminate the MgO and Mg3B2O6. The effect of acid concentration on the selective leaching was studied at different concentration range, solid/liquid (S/L) ratio, and temperature. The products obtained were characterized by using X-ray diffraction, chemical analysis and SEM techniques.

Jan 1, 2009

By Denise Crocce Romano Espinosa

The recycling of waste of electric and electronic equipment (WEEE) is one of the main modern challenges. Among the variety of WEEE, batteries can be set apart due to their composition and their growing demand along with portable devices. The objective of this work is to characterize the thermal behavior of a sample of mixed types of batteries using a thermobalance (TGA). The results of tests showed that Cd evaporated up to 800ºC, Zn evaporation occurred mainly above 900ºC and manganese oxides were pre-reduced to MnO at temperatures above 900ºC.

Jan 1, 2009

By José Carlos D?Abreu

The Tecnored process is a new ironmaking technology, developed on a unique approach that combined empirical and theoretical knowledge backed by extensive tests carried out in a dedicated pilot-plant and with close support of universities and research centers. Campaigns in the pilot-plant focused on operate different reactors of different sizes, including a full size slice of the industrial furnace. This approach provided actual conditions to develop the main features of the process such as the internal dimensions, raceway pattern, thermal and gaseous profiles, etc, besides provide reliable data to feed and calibrate a specific mathematical process modeling. This paper presents the first computer model used by the Tecnored technical staff, focusing the behavior of a self reducing agglomerate in the upper shaft of the furnace (zone of solid state reduction). Some results of this model are given and discussed.

Jan 1, 2006

By Hani Henein

Recent innovations in atomization of molten metals have occurred in the area of single fluid atomization. Impulse Atomization (IA), one of the single fluid techniques, provides unique capabilities to study different regimes of atomization in a controlled environment. By changing processing variables, a mono-dispersed distribution of droplets above one millimeter in diameter can be produced. This is accomplished through proper characterization of the forces influencing the process and in particular the flow of melt through the orifice. This paper will discuss the approach and illustrate results with molten aluminum and cobalt.

Jan 1, 2006

By S. Eck

In previous work the influence of the casting speed on the flow field and the shape of the solidification front in an industrial 0.82 x 0.25 x 0.8 m³ bronze caster had been investigated. Both numerical and experimental model represented 1:1 the real caster geometry. A comparison of the results of both numerical and experimental models for the flow during the casting process showed a good agreement in the qualitative velocity fields (flow direction and vortex formation). This work represents a parameter study of the numerical model with variations of the turbulence conditions at the inlet in order to clarify their influence on the flow field in the caster. In order to find the best boundary condition at the inlet, the numerical calculations for water have been compared with the measured flow fields in the water model. The new boundary conditions were then applied to the numerical model of the bronze casting process.

Jan 1, 2009

By Napisporn Memongkol

Syntheses of Al-TiC-Al2O3 and Al-SiC-Al2O3 composites were obtained in situ by carbothermal reduction of mixtures of Al powder, TiO2 powder and activated carbon powders and Al powder, SiO2 powder and activated carbon powders. The reductions were carried out in a horizontal tube furnace under flow of inert gas. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The synthesized products were mixtures of aluminum reinforce with titanium carbide and alumina and aluminum reinforce with silicon carbide and alumina. The effect of the reaction temperature (1000 o C ? 1200 o C) and condition of precursors on the Al powder, TiO2 powder and activated carbon powders and Al powder, SiO2 powder and activated carbon powders were investigated using XRD and SEM method. The synthesized products showed those composites with aluminum matrix and titanium carbide and alumina as reinforced phases and aluminum matrix and silicon carbide and alumina as a reinforced phase was formed.

Jan 1, 2006

By W. M. Cross

Bubble attachment time measurements for the rare-earth phosphate minerals monazite and xenotime were made as a function of oleate concentration, sodium fluoride addition, and temperature. Results indicate that the rare-earth phosphates behave similarly to other phosphate minerals, notably collophanlte and fluorapatite, which have been studied previously. The addition of sodium fluoride yielded a modest decrease in bubble attachment time with fluoride additions below the apparent fluoride surface precipitation point, while at fluoride additions greater than the apparent precipitation point a significant decrease in attachment time occurs. Increasing the temperature or the system gave a slight decrease in bubble attachment time in the absence or sodium fluoride. With sodium fluoride addition and below the apparent fluoride surface precipitation point, an increase in temperature actually increased the attachment time. For sodium fluoride additions above the apparent fluoride surface precipitation point, a temperature increase significantly decreased the attachment time.

Jan 1, 1989

By Pengfu Tan

The control of converter slag chemistry and slag viscosity has played an important role in optimizing converter operations. A thermodynamic model of copper P-S converter and a viscosity model of converter slag have been used to predict the chemistry and viscosity of converter slag. The effect of oxygen potential, SiO2/Fe in slag, detection of slag blow endpoint, and temperature on slag viscosity, liquidus temperature of converter slag and skimming operation has been discussed. Some applications of the industrial operations have been presented.

Jan 1, 2006

By Emmanuel N. Zevgolis

Energy required for roasting and smelting of a nickeliferous laterite ore by the rotary kiln - electric furnace process is investigated. From this work it comes that thermal energy is about 65% of the total energy needed and the rest is electrical. Also, 61.3% of thermal energy input in the roasting step (of all combustibles fed into the rotary kilns) is used for pre - heating, 11.6% for pre - reduction and the rest (27.1%) corresponds to the energy of the remaining carbon in the rotary kiln products (i.e., calcine, dust and coatings). Carbon entering the system is used as follows: 57.9% for combustion, 37.1% for reduction and the rest (5.0%) remains unburnt. Exploitation of energy from gases of both furnaces, as well as the higher possible reduction degree, the optimum temperature of the calcine and also elimination of the excess air in the rotary kilns, improve significantly energy balance and economics of the process.

Jan 1, 2006

By Y. F. Liang

Fe-6.5wt.%Si alloy has excellent soft magnetic properties compared with conventional silicon steel. It is very brittle at room temperature due to appearance of ordered phases, like B2 and DO3. In this paper, we investigate the effect of ordering on cold workability of this alloy. Methods of rapid quenching and hot rolling were utilized. It is found that rapid quenching and proper heat treatment of the hot rolled sheet could decrease the degree of order due to the very high solidification rate and high cooling rate. The rapid quenched sheet and hot rolled sheet after proper heat treatment could be cold rolled without crack. Microstructure, phase ordering, micro hardness, and cold rolling properties were investigated by Optical Microscope, X-ray Diffraction, Micro Hardness Indenter and Four-high Mill.

Jan 1, 2009

By Xiaodong Wang

A liquid metal flow generated by a magnetic field whose traveling direction is periodically reversed, the Reversed Traveling Magnetic Field (R-TMF) is studied. The modulation frequency ranges from 0 to 6 Hz. Ultrasonic Doppler velocimetry probes the generated fluid flow. Depending on the modulation frequency, a number of characteristic flow features are exhibited. A transition frequency (approximately 4 Hz) exists, above which the flow is no longer sensitive to the force modulation. Below this transition point, the amplitude of the velocity oscillation increases, and then below fm = 0.05 Hz, it saturates around a value close to that observed without any modulation. A theoretical model to obtain an analytical solution of electromagnetic force and to predict flow motion is developed, which is fairly in agreement with the experiments.

Jan 1, 2009

By A. Broussaud

An original methodology has been developed for steady state simulation of selective grinding and mineral liberation in rod and ball mills. Three fundamental aspects of the methodology are presented successively : modeling ore texture, modeling grinding and its selectivity, and modeling mineral liberation. The methodology for modeling ore texture includes the conversion of 2D data into 3D reconstructed information and the use of the BILCO coherent material balance software. The models for grinding Simulation are classified into three levels, corresponding to three levels of available experimental data. All models account for grinding selectivity and for variations of engineering para-meters and operating conditions. An algorithm has been introduced to forecast mineral liberation, compatible with accurate simulation of selective grinding, which generates reasonable results.

Jan 1, 1987

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been studied on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27° between each tuyere, and five side tuyeres with an angular separation of 22.5° or 27° between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

In this study, the method of chemical co-precipitation?reduction?diffusion was developed for the preparation of magnetic SmCo5 alloy. In the chemical co-precipitation process, the effects of solution pH, the reactant concentration, the dispersant on the process were investigated. The optimum conditions of the process were determined, and the SmCo5 alloy oxide precursor particles with fine crystalline structure, narrow size distribution was obtained. Then, by reduction-diffusion treatment of the precursor particles, the SmCo5 alloy with high quality was produced. It is anticipated that the co-precipitation-reduction-diffusion is a novel method available for SmCo5 alloy production.

Jan 1, 2006

By D. Death

The Tapping Camera Prototype (TCP) is an instrument being developed to record and analyse video of the molten metal stream entering a tapping crucible as it is tapped from an aluminium reduction cell. The development aims to provide potroom floor operators with continuous real time vision of the tapping process and provide an alert in the event of excessive bath contamination in the extracted metal stream. Longer term the system may provide sufficient data to enable control of the tapping process. The TCP mounts a wireless camera and periscope to view the molten metal stream via a peephole in the tapping crucible. Real time video is recorded to either digital video tape or computer disk for subsequent video analysis to quantify the bath material drawn into the tapping crucible with the molten aluminium. The images transmitted by the camera are available on a handheld LCD video screen. This work is an initiative of the CSIRO?s Light Metals Flagship.

Jan 1, 2006

By F. A. Guo

Ultrafine-grained surface layers were obtained by surface mechanical attrition treatment (SMAT) in copper and titanium samples. The thermal properties of the deformed layers were characterized using a scanning thermal microscopy (SThM) that allows thermal conductivity to be mapped down to the submicrometer scale. A theoretical approach, based on this investigation, was used to calculate the heat flow from the probe tip to the sample and then estimate the thermal conductivities at different scanning positions. Experimental results and theoretical calculation demonstrate that SThM can be used as a powerful tool for the thermal property and microstructural analysis of ultrafine-grained microstructures.

Jan 1, 2006

By Hugo Cabrera-Real

This work investigated the chemical and mineralogical properties of CaO-SiO2-CrOx-CaF2- MgO slags. Synthetic slags were prepared and the effect of the slag basicity (CaO/SiO2) and MgO contents on the stability of the mineralogical species formed was analyzed. The morphology and composition of the slags were analyzed by XRD and SEM-EDS, whilst their chemical stability was evaluated by leaching with an aqueous acetic acid solution. It was found that in slags with CaO/SiO2 = 1, the main Cr-compound was MgCr2O4 spinel, which forms octahedron crystals. Small amounts of CaCr2O4 and CaCrO4 were also observed. It was found that increasing the slag basicity from 1 to 2 the compounds MgCr2O4 and CaCr2O4 were formed together with the Cr(V)-containing compound complex Ca5(CrO4)3F which forms hexagonal crystals. The results showed that the highest chromium concentration levels in the leaching liquors corresponded to slags with CaO/SiO2 = 2, probably owing to the formation of Ca5(CrO4)3F.

Jan 1, 2010