Search Documents

By S. N. Monteiro, C. M. F. Vieira, M. M. Ribeiro

"This work has as its objective to evaluate the effect of incorporation of the powder waste retained in the eletrostatic precipitator of the sintering stage from an integrated steel making plant on the physical and mechanical properties of a red ceramic. Formulations were prepared with incorporation of the waste in amounts up to 20 wt.% into a kaolinitic clay. Rectangular specimens were prepared by uniaxial mold-press at 20 MPa and then fired at 750, 900 and 1050°C. The evaluated physical and mechanical properties were: linear shrinkage, water absorption and flexural rupture strength. The results showed that the waste has a potential to be used into red ceramics. The incorporation of the waste enhanced the properties of the ceramic, decreasing the water absorption and increasing the mechanical strength at all investigated temperatures.IntroductionThe sintering stage of an integrated steel-making plant is dedicated to the agglomeration of a mixture of iron ore, coke or coal, fluxes and water [1]. It is a common practice in this stage to use of solid wastes with great amounts of iron in the form of sludge and powder. One of the atmospheric pollutants generated during the sintering process is the particulate material, which is normally retained in an equipment denote as electrostatic precipitator. This equipment retains very small particulates, present in the gaseous emissions by application of an electrical potential difference in between the plates that the fluid is forced to go through. [2]."

Jan 1, 2011

By Guangliang Wu, Dongchang Huang, Xinbin Liu

Oxidation Kinetics of SPHC was analyzed by TGA, and the curve of oxidation weight gain with different temperature was acquired. It is found that, when the oxidation temperature is between 500 and 600 , all the curves are linear; when the oxidation temperature is above 700 , the curves are close to parabolic. At the temperature of 900 , the oxidation weight gain increases dramatically. The TGA results indicate that the activation energy of SPHC steel is 146.19 kJ/mol at the temperature of 500 900 , and an oxidation kinetic model was set up for variable temperature. Based on the temperature change during rolling process, numerical simulation of oxide scales evolution was carried out for SPHC steel, and the simulation result agreed well with measured ones. It can provide a basis for estimating the scale growth and controlling the temperature on site.

Jan 1, 2016

By C. Beckennann, C. Y. Wang

"Computer simulations of structural and compositional development in equiaxed dendritic alloy solidification are performed using a recently developed multi phase model. The model not only accounts for the transport phenomena occurring on the macroscopic (system) scale, but includes also the grain nucleation and growth mechanisms taking place at various microscopic length scales. In this paper, a numerical technique consisting of a fully implicit control-volume based finite difference method and a multiple time step scheme is developed for accurate and efficient simulations of both micro- and macro-phenomena. Sample numerical results are presented to reveal the effects of liquid now and crystal sedimentation on segregation and the final grain size distribution. In particular, the importance of the interplay between the dendrite microstructure and multiphase now patterns is shown.IntroductionIn recent years, modeling of equiaxed dendritic solidification without convection has experienced considerable progress (1,2]. Nucleation and growth kinetic laws have been coupled with transient heat conduction calculations to determine the solidification microstructure. However, modeling of equiaxed dendritic solidification with melt convection and solid movement has not been attempted so far, largely because of the complications associated with the transport of free equiaxed crystals in the melt. The gravity-induced transport of free crystals is fundamental to the development and extent of the equiaxed zone and also greatly affects the columnar to equiaxed transition. Another possible effect of crystal sedimentation or floatation is to cause severe macrosegregation as well as structural inhomogeneities. The only study available in the literature that accounts for both liquid convection and solid transport is by Ni and Beckermann (3], but deals with globulitic structures (as opposed to dendritic)"

Jan 1, 1994

By Charles H. Rawlins

Reported is work done on processing of steel mill effluents in the areas of dewatering and separation. Much of the waste from these operations is in the form of sludges from scrubbers, in which the primary constituent is iron oxide. Recycling of the sludge&apos;s magnetic fraction has become economically attractive in order to reduce the overall volume placed in landfills. The objective of this research is to determine the effectiveness of combining magnetic and cyclonic forces, to recover iron oxide particles from waste water stream, while decreasing the volume to be disposed. Three different size hydrocyclones, operating within the field of a quadripole magnet, were tested using varying feed pulp densities of magnetite, magnetite/dolomite, blast furnace (BF), and basic oxygen furnace (BOF) slurries. In the first three cases, the percentage of magnetics recovered increased to greater than 95%. The limiting operational factors are; high pulp density for small cyclones, which can cause flow blockage within the magnet field, and extremely fine particle sizes (<2 microns), which cannot be recovered. The results indicate this technique can remove virtually all the magnetic particles from some steel effluents to a 40-50% weight percent solids pulp, on an in line continuous basis.

Jan 1, 1994

By Mostafa O. El-Bealy

"To estimate the interdendritic cracking tendency in casting processes, a new model for interdendritic cracking criteria has been proposed. The model combines a concept of the alloying element effect on the interdendritic strain generation and therefore on the susceptibility of interdendritic cracking phenomena. A susceptibility of interdendritic cracking is modeled by using El-Bealy's interdendritic cracking susceptibility function ""BJCSF' and the opening displacement between the dendrites ""EIA "". These concepts are modeled based on the previous experimental observations and ElBealy' approach. The model is implemented numerically for a one-dimensional model problem with some similarities to the casting of steel. The variation of some key parameters that are known to influence the frequency and severity of the interdendritic cracking is then studied.I. INTRODUCTIONInterdendritic cracking ""hot tearing"" commonly encountered in both ferrous and nonferrous castings (1,2]. It is generally believed that interdendritic cracks start to nucleate and develop in the interdendritic strain region within the mushy zone [l-5]. The interdendritic strain region is then definitely coherent, but continuous films of liquid still exit (4,5]. This distinguishes interdendritic cracks from cold cracks forming during the casting process after complete solidification (6,7].Much effort has been put into the understanding of the interdendritic cracking phenomena, and several theories have been proposed. Fellini [8] stated that interdendritic crack ""hot tear"" will result if the material is subjected to too high of accumulated strain within so called vulnerable part of the solidification interval. Kinosita et. al. [9] and Campbell (10] also emphasized the role of tensile stresses in the forming of interdendritic cracks. Most interdendritic cracks criteria simply consider the size of solidification interval, stating that solidification range is associated with a lager interdendritic cracking susceptibility than a short range. Clyne and Davies (11] formulated a more refined such criteria based upon the time spent in different regimes of the solidification interval. They defined a vulnerable region in which thin continuous films of interdendritic liquid exist, and the permeability is low. When thermal strains are induced in this region, the film is not able to sustain the stresses, and an interdendritic crack will form."

Jan 1, 2001

By Shi Guan-Yong, Niu Li-Ping, Dou Zhi-He

"In the preset work, the viscosity model (named modified KTH model) proposed by Sichen Du and S. Seetharaman et al and extended by Shu Qi-feng was applied to the ESR slag systems. A correlation to predict the viscosities of CaF 2-(CaO)-Al203 slags using interaction coefficients of different cations in the presence of oz-and viscosity interaction coefficients between oz-and F in the presence of different cations has been developed. The interaction coefficient between oz- and F- in the presence of Al3+ was determined from the experimental data as shown in known literatures. The good agreement between the calculated viscosities and the experimental data in the CaF2-(CaO)-Al203 systems has indicated that this approach can be successfully employed to predict the viscosities of ESR slags.IntroductionReliable viscosities data of high-temperature slag melts are important for the modeling and design of high temperature metallurgical processes. Although a number of experimental measurements have been carried out, the available viscosities data is still scarce compared to the needs of today's technology, especially in the case of complex melts. In process simulations, the needs of viscosity descriptions for complex systems which could enable the extrapolation of the data as functions of temperature and composition is strongly felt today."

Jan 1, 2013

By Andreas Nolte

This paper includes a comprehensive report about the metallurgical utilisation of reusable products from electronic scrap recycling, car shredding industry, used glasses an various waste products, such as slimes and flue dusts, generated in a secondary copper smelter. Depending on the copper content, the type of copper compounds and the characteristics of accompanying substances, the materials are treated by smelting in furnaces, operating under reducing or oxidizing conditions. HKs pyro- and hydrometallurgical processes, blast furnaces, converters anode furnaces, tin lead alloy plant and tankhouse will be outlined. The reusable products are categorized according to the origin of the materials and then presented in the form of quantity and quality balances. Processing methods, process able quantities and quality requirements of inputs are described. The utilization degree of the most important metals (copper, tin, lead and zinc) is described with graphics. The report is rounded by information on operating licence according to the environmental regulations of the Federal Republic of Germany and data concerning supply and contracts

Jan 1, 1997

By R. J. Kuczynski

The U.S. Bureau of Mines Reno Research Center operated a batch pilot plant to demonstrate high-temperature cyanide leaching for recovering platinum group metals (PGM) from automobile catalysts. Approximately 1,600 kg of used pellet, monolith, and metal support catalyst containing 1,680 g (54 tr oz) of PGM were processed. Forty-five-kilogram batches of used catalyst were leached with sodium cyanide solution at 160° C for 1 h under basic conditions in a countercurrent processing sequence to dissolve the PGM. Extractions from the used pellet catalyst ranged from 94 to 95 pct for Pd, 95 to 97 pct for Pt, and 64 to 81 pct for Rh. Extractions from the used monolith catalyst ranged from 7B to BB pct for Pd, 75 to 90 pct for Pt, and 43 to 71 pct for Rh. Heating the pregnant leach solutions to 275&apos; C for 4 h destroyed the PGM-cyanide complexes, resulting in over 99.7 pct of the PGM precipitating from solution. The PGM precipitate was predominantly a powder metallic concentrate, typically analyzing greater than 50 pct PGM. Heating destroyed cyanide to less than 0.2 mg/L. Both the pellet and monolith residues were evaluated for disposal using the EPA Toxicity Characteristic Leaching Procedure.

Jan 1, 1995

By Yonggang Liu

Microstructure and precipitates in hot rolled low carbon steel sheet by CSP were investigated in this paper. It is pointed out the precipitates in low carbon steel sheet by CSP are different with that by traditional hot rolling. The bainites were found in CSP hot rolled steel sheet by TEM testing and these bainites could maintain in the sheets even after batch annealing. The selected area electron diffraction analyzing indicated that there were many CrB2BN and FeB4BN phases precipitated in hot rolled steel sheet and no AlN grains precipitated. The nitrides forming can limit AlN grains precipitating during the batch annealing processing, and this could do harm to the texture pipeline along orientation line forming with formed properties.

Jan 1, 2006

By Aurelian Buzaianu, Cristian-Aurelian Popescu, Gabriela Popescu, Petru Moldovan

"A lot of scraps result in processing of composite materials which contain metallic phases that can be recovered and used again in different field. Considering this point of view the aim of the paper was to separate and recover aluminum from aluminum matrix/graphite composites. The separation and recovery of aluminum alloy from aluminum alloy/graphite composites was done by treatment with halide molten salts. As halide salts were used flux tablets that collect the ceramic particles in dross. After dross separation, was used filtration in order to separate the aluminum matrix from the other impurities.Samples from the recovered alloy were analyzed using chemical analysis, optical and electron microscopy, as well as X-ray diffraction. The desired composition of the aluminum alloy obtained from scraps could be reached by some addition of metals to the metallic phase. From optical microscopy it was obvious that the structure of the aluminum alloy obtained after composite reclamation consists large particle of silicon, eutectic, a-Al solid solution and other phases like Fe, Si, Mg and Ni, or some compounds like CuAl2. 1. IntroductionThe research on the recycling and reclamation of metal-matrix composites (MMCs) becomes active to preserve the natural environment, as environmental requirements become stricter, to save energy, and to reduce garbage. In case of recycled aluminum alloy ingot the production energy is about 3 pct of that of the new ingot. This evidence strongly supports the necessity to recycling of aluminum alloys. Among aluminum alloys, metal matrix composites have high strength and elastic modulus, and also good were resistance. These materials have been developed to meet the demand properties which exceeds that of the ordinary materials, and to save energy."

Jan 1, 2008

By S. Abe

An extensive study has been carried out to determine the true cause of floating slimes precipitation which sometimes occurs and badly affects the quality of copper cathodes. Soluhilities of floating slime compounds systematically measured for the ternary system As-Sb-Ri added solely or in combination with conventional copper electrolyte (63°C) and bench scale electrorefining experiments done by varying electrolyte composition, have shown conclusively that the level of Sb(V) ions plays a substantial role in the precipitation mechanism. It was, therefore, speculated that controlling the level of the less soluble S b ( V ) ions below a certain critical level should result in a complete elimination of the undesirable precipitation. This can be easily achieved, for instance, by the addition of a reducing agent such as SO2 gas and the simultaneous employment of a certain type of cheating agent that effectively removes excessive Sb and Bi from the contaminated electrolyte. Long-term pilot testing conducted in line with the above speculation has confirmed the SO2/chelating resin scheme to be industrially very attractive and feasible.

Jan 1, 1987

By J. S. Becker

Technology developed and first implemented in the United Kingdom enables very low grade aluminum scraps containing oils, organics, plastics and ferrous metals to be directly charged, without pretreatment, into a unique melting furnace. The system has been in full scale production for four years. The oxy-fuel-based furnace design incorporates internal afterburning in the furnace&apos;s hot zone, producing excellent thermal efficiency and very low emissions. The furnace is inherently low in NOx. This paper will provide both theoretical background and extensive operating results for this new melting concept. Applications describing both purpose built new furnaces and retrofits of existing reverberatory furnaces will be presented. Extensive operating emissions data will be presented.

Jan 1, 1997

By W. G. Davenport

This chapter examines three minor influences on flash smelting&apos;s industrial oxygen and oil requirements, i.e.: (a) recycle of molten converter slag to the flash furnace (b) gangue oxides and carbonates (e,g, Ah03, CaC03) in the flash furnace feed (c) minor sulfides (e.g. NiS} in the flash furnace feed. It then examines the. sensitivity of our flash furnace calculations to previously ignored aspects of smelting chemistry -Cu, S and Fe304 in slag and 0 in matte.

Jan 1, 2001

By Keith Rozenburg, Ivar Reimanis, Jesus Chapa

"Experiments in conjunction with finite element analysis (FEA) are used to better predict crack propagation in ductile/brittle graded composites. Cu/W graded composites were fabricated by stacking discrete layers of powders and hot pressing. Crack propagation was studied by loading a notched beam in four point bending and examining the subsequent crack deflection. The notch was placed within a particular composition of material, oriented in a direction perpendicular to the gradient direction. Elastic and plastic mismatch between different constituents in the graded composite induce shifts in the phase angle of loading, thereby causing the crack to deflect. FEA indicates that thermal residual stress has a negligible ""influence on the crack path. The combined FEA and experimental results suggest that elastic mismatch is the single most important material property-related factor in controlling crack deflection.IntroductionMany 'applications would benefit or may even require materials whose performance or functionality must vary spatially. While the concept of functionally graded materials has existed for nearly one hundred years, it is only within the last fifteen years, that research efforts have focused on generic issues in processing, properties and performance of functionally graded materials. This generic research effort has brought together scientists and engineers from traditionally different disciplines to address common issues with graded composites. The current work focuses on issues in structural joining. A wide variety of applications require some type of joining between dissimilar materials. Examples include thermal barrier coatings for turbine engines, wear resistant coatings for tools, ceramic engine parts, and microeiectronic devices, as well as many traditional applications involving metallic welding. The joints may either be discrete, involving a single interface, or they may· be spatially graded in composition. Extensive theoretical and experimental information exists on discrete bimaterial and trimaterial joints, but relatively little exists for graded joints or composites"

Jan 1, 2000

By Natasa Mitevska

In order to ensure the minimal copper concentration in the reverb furnace slag, the graphical optimization method is used and the optimal slag composition of the reverberatory furnaces No.1 and No.2 in the RTB BOR, Copper Smelter and Refinery (Serbia) is obtained: (Si02) .. 38.0%; (FeO) .. 40.0%; (Fe3O4) = 5.0%; (CaO) = 5.0%; (Al2O3) .. 6.0%. Keywords: Optimization, Reverb Furnace Slag, Graphical Method

Jan 1, 2003

By Mansoor Barati, Shaghayegh Esfahani

"The slag from extraction of ferrous and non-ferrous metals is a potential heat source which if treated properly can contribute to recovery of a significant amount of energy. The waste heat of slag may be used to generate steam, synthetic fuel gas, or electricity. Although several technologies have been investigated for this purpose, very little has been achieved in terms implementing the technology in industry. In this article, the development and application of various granulation techniques are reviewed and the methods to recover energy from granulated slag are discussed.IntroductionEvery year, more than 422 million tons of slag is being produced around the world as a by-product of the metal manufacturing at temperatures of up to 1300-1600°C [1, 2]. Currently slags are either disposed of or treated by processes such as granulation. Through the granulation process, most slags can be converted into a material which may be fully used as a cement feedstock. Conventional cement production is an energy intensive process with large emissions of CO2; therefore, the replacement can both be energy saving and environmentally friendly. However, for this purpose, the slag should have what is known as a “glassy” content (i.e. it should be amorphous) which requires rapid cooling rates that are not easily achieved due to the very low thermal conductivity. The main challenge in all these processes is to granulate the slag at a high cooling rate while the heat is also being recovered."

Jan 1, 2012

By Pan Gu, Zhen Zhang, Jiang Diao, Bing Xie, Hongyi Li

Furnace refractories are in most cases chemically incompatible with smelter slag, which leads to a steady erosion in their thickness over time. Once too thin, refractory walls become mechanically unstable and catastrophic failure can result. Historically, external shell cooling was applied to generate a freeze lining of slag and thus prevent refractory erosion. Many modern high intensity smelting furnaces instead maintain their physical integrity by the use of internally cooled wall panels, plates or finger coolers. An initial refractory lining is often installed inside of the coolers, such that the furnace originally operates with a temperature (insulated) rather than a heat flux (freeze lined) boundary condition. This paper examines the change in slag-wall heat transfer coefficient and slag superheat as a function of process intensity. The implications of the changes in heat transfer on residual brick thickness are explored using analytical modelling.

Jan 1, 2016

By W. E. Straszheim

Computerized microscopic techniques were used to determine the size and identity of the ash-forming mineral components, as well as their association with the organic coal matrix, in order to aid in the development of physical methods of beneficiation which require such characterization for the most effective cleaning. Examples of particle size measurements, mineral phase identification, and especially coal-mineral association results are given for selected samples of raw and physically cleaned coals. These measurements can reveal certain characteristics of coals which can be be of significant value in predicting coal recovery and mineral matter rejection for coals undergoing beneficiation.

Jan 1, 1989

By R. E. Fanning

"IntroductionThe Aluminum industry is one of many materials industries which strive to make their material the preferred choice for large volume products. In some applications one material has a natural advantage over others, but more frequently several materials compete with one another, each providing one or more advantages and some trade-offs. Customers may design their product with several objectives such as minimum system cost, maximum customer appeal or maximum manufacturing flexibility, choosing materials which best combine cost and performance. In such markets it may become necessary for a material supplier to enhance the attractive features of the particular material to outweigh its disadvantages.It is difficult, if not impossible, to predict how various materials will evolve. Technological breakthrough, government regulations, material availability or sociological issues may redefine the balance between competing materials. In spite of some uncertainty regarding the competitive position of competing materials, there is little doubt that unrelenting pursuit of product quality improvement and cost reduction are essential to future viability of the aluminum industry. It is the intent of this paper to identify some areas where technological improvement would be beneficial. Thus this paper is a collection of briefly described problems that will hopefully stimulate the thoughts and research required for knowledge based solutions. Rolling ProcessA particular example is the beverage can industry where aluminum, steel, glass and plastics vie for a share of the m.arket. The high cost of aluminum relative to steel or glass requires minimizing the amount of metal per can. The high intrinsic value of aluminum has led to extensive recycling of cans although net metal cost is still higher than that of the competing materials. Intensive engineering of the beverage can led to improved design and better understanding of material requirements. These improvements permitted substantial reduction in sheet thickness over the past decade. The downward trend in metal thickness for beverage can sheet is shown in Figure 1."

Jan 1, 1988

By T. Plikas, L. H. Gunnewiek, L. Oshinowo

"Electric furnace smelting is one of the principal unit operations for ferroalloy production, and increased process intensity, improved availability, minimal maintenance and a longer campaign life are common objectives for electric furnace operation in order to obtain favourable economics of production. Furnace designers have continued to develop innovative solutions, e.g., furnace cooling systems, that have allowed these objectives to be realised and CFD modelling plays a key role in the design process. Enhanced understanding of the energy transfer process in the furnace and the ability to develop, evaluate and optimize components of the crucible design to match process requirements are the key motivators for modelling.This paper provides an overview of recent applications of CFD to the design of electric furnaces. The aim is to illustrate what can be done, and identify areas where further work is needed in this field. Examples include furnace bath simulation, crucible cooling system design, taphole design, baking of Soderberg electrodes, off-gas systems, and fume control and building ventilation. It is argued that the trend is for numerical models to become more encompassing while at the same time more accessible, and therefore further improvements in furnace design will be realised with continued and well validated modelling efforts.IntroductionOne of the main processing steps in ferroalloy production is the smelting of ore in electric furnaces. The three-electrode, AC submerged arc furnace is most prevalent method for smelting in the industry, with shielded-arc and DC plasma arc furnaces achieving limited application (1,2). Commercial furnaces range in size from a few megawatts to more than eighty megawatts of supplied power, and operate with the objective of maximising the return on capital invested. Maximising productivity and energy efficiency are two pathways to achieving this objective, through process intensification, increased availability, minimal maintenance, and increased campaign life for the furnace and associated equipment. Concurrently, the need to reduce the environmental impact of metal production by controlling the emission of particulate emissions, greenhouse gases, and other harmful by-products must also be met."

Jan 1, 2004