Search Documents

By Wenzhou Yu, Cong Zhang, Wenhui Ma, Gang Wang, Kuixian Wei

"A novel technique was successfully developed for nickel further purification by vacuum directional solidification. The removal effect of impurities in nickel was studied based on theoretical analysis and experiments. High removal efficiency of impurities in nickel can be realized according to theoretical analysis. The experimental results show that the vacuum directional solidification treatment could increase the nickel purity from 99.96% to 99.996%. Since vacuum directional solidification could effectively remove the impurities from nickel with low contamination and low cost, it is a potential route to obtain high-purity nickel for commercial application.IntroductionNickel is widely used in metallurgy, machinery, petroleum industry, chemical industry, construction industry, light industry, and other industries for its ductility, medium hardness, ferromagnetism and high chemical activity. Nickel-based alloy is an important material for the key parts of aircraft, tanks, submarines, radars, nuclear reactors and aerospace fields [1-5]. Generally, nickel contains Si, P, S, Fe, Cu, Zn, As, Cd, Sn, Sb, Pb, Bi, Al, Mn, Mg and other impurity elements, which may hinder the commercial application of nickel. Therefore, it is necessary to refine the crude nickel for the high purity nickel."

Jan 1, 2014

Based on experimental and computer simulation results from our group, we report a systematic, atomic level analysis of carbon dissolution from carbonaceous materials in molten iron. Experimental results on graphite / Fe-C-S system were obtained using carbon dissolution studies, XRD and FESEM investigations and were supplemented with Monte Carlo simulations. Three basic mechanisms, namely carbon atom dissociation rate, interfacial phenomena and mass transfer in the melt were found to be responsible for the overall dissolution process. While mass transfer in the melt is governed by the concentration gradients, melt composition and temperature; impurities present in ash play a significant role in the interfacial phenomena. For less ordered forms of carbonaceous materials, carbon atom dissociation rate depends strongly on the degree of long-range order and is an important rate controlling mechanism in the overall dissolution process. A systematic comparison of dissolution rates for a variety of coal-chars, natural and synthetic graphites has been carried out in an attempt to identify rate-controlling mechanisms. The structure of the carbonaceous material appears to be an important underlying factor in the carbon dissolution process.

Jan 1, 2003

By B. R. Baldock

The converting of high-grade nickel matte for production of low-sulphur matte or nickel metal is a process which has eluded metallurgists in the past because of the limitations of conventional converting furnaces. The high temperatures required and the refractory nature of nickel oxide has prevented practical success in a process which has been known to be theoretically feasible for a long time. The Ausmelt top submerged lancing system is capable of operating under close control of the smelting conditions. High temperatures and both rapid oxidation and rapid reduction can be achieved. These features have provided the basis for successful pilot plant trials of the desulphurisation of high-grade matte from the Kalgoorlie Nickel Smelter. Sulphur level in product was lowered from 20 to 25% to as low as 0.2%, with iron levels in matte in the range of 1.0 to 3.5%. The theoretical background of matte desulphurisation is surveyed and the pilot plant operations described. The implications of the results in relation to commercial plants and possible refinery operations are summarised.

Jan 1, 1993

A modified Cuprex Metal Extraction Process (CMEP) leach process was used to extract Cu. Ni and Co from a complex sulphide concentrate. The standard leach was modified to a two-stage countercurrent leach which provided emf control of the copper SX feed and minimized iron dissolution. A flowsheet was developed to recover the base metals and silver from the leach solution and gold and platinum group metals from the leach residue which was predominantly elemental sulphur. Techniques required to maintain an iron balance in the system including pressure oxidation and solvent extraction are described.

Jan 1, 1996

By F. H. A. Abdalla

A process is described for the recovery of valuable nonferrous metals from steelmaking dust by suiphatizing roasting using ammonium sulphate. Maximum recoveries of soluble metal sulphates achieved at optimum conditions were> 99.0 %. Selective metal separation of the soluble sulphates in the leached liquors were performed either by controlling the roasting temperature or by adjustment the pH values of the leached liquor ranging from 3.6-6.2. Either pure zinc oxide orland tin oxide could be obtained at optimum conditions, and the products were evaluated chemically and by X-ray analyses. The residues rich in iron oxide can be removed and recycled. The mechanism of sulphatizing roasting process was considered. A general flow-sheet for the overall process of treatment the steel making dust to recover its valuable nonferrous metals was suggested, which ca be applied for other nonferrous bearing materials.

Jan 1, 1996

By J. Sjöblom

New copper and nickel processes, flash converting and DON, direct high-grade nickel matte smelting, have been developed in order to replace the conventional and not so environmentally friendly PS-converting process. With a laboratory scale laminar-flow furnace the combustion reactions of sulfidic feed particles can be investigated under simulated flash smelting conditions. In the present study, finely ground and screened feed fractions of a copper matte and a nickel matte were flash oxidized in a laminar-flow furnace. The experiments were carried out using 20, 21 vol% and 75 vol% O2 in nitrogen, at temperatures 1100 and 1300 °C and reaction zone length of 7.5-16 cm. The samples were quenched in a water film after a specified reaction time. The matte particle reactions were stopped after short residence time intervals in order to obtain a better understanding of the reaction mechanisms. Chemical analysis was used to determine oxidation degree, and optical and scanning electron microscope combined with energy dispersive analysis was used for characterization of the reacted particles. On the basis of the experimental results the reactivity of the mattes is discussed and possible reaction and dust formation mechanisms are considered.

Jan 1, 1999

Achieving continued economic growth with social equity within the natural limits of the Earth's 'eco-systems is the major issue facing the world today. The material and energy needs of the world cannot be met with the current ways of addressing this issue. The need for metals, an important class of materials, will continue into the future because their unique properties make substitution by other materials impossible in many applications and this need will continue to be met from primary metal production and recycling. However, the recycling rate will increase and the usage pattern of metals will change to reflect the environmental impact of their production and use. Pyrometallurgy has an important role in meeting the metal needs of the future since some metals can only be produced pyrometallurgically; the energy required to produce some metals pyrometallurgically is significantly less than by other methods; most metals are most efficiently recycled pyrometallurgically; and the release of harmful and toxic elements into the biosphere can sometimes best be controlled through pyrometallurgical processing. The development of strategies for pyrometallurgical processing for the future lies in the recognition that sustainable development calls for large step improvements in value delivered per unit of environmental impact over the entire supply chain. Pyrometallurgists can respond to this challenge by contributing to reducing the environmental impact of meeting metal needs using three broad strategies: "end-of-pipe" approaches to convert emissions into benign materials for storage or disposal; flowsheet redesign to limit or eliminate emission production; and improved recycling technologies. A number of examples are discussed to illustrate how the sustainability driver is already influencing the technological development of pyrometallurgical processes, and how these will develop further as the sustainability driver strengthens.

Jan 1, 2003

By Vladimir Panjkovic, Ostrovski. Oieg, Campbell Cripps Clark, John Truelove

"Effects of properties of raw materials and blast on the performance of an iron bath reactor have been examined by a mathematical model. The model consists of three modules: 1) chemical reactions in the gas phase and heat transfer from gas to droplets ejected from the bath; 2) heat losses from the vessel and radiative heat transfer from the freeboard to the bath; and 3) heat and mass balances for the bath. The following parameters of the process are calculated: coal, ore, flux and oxygen consumption, post-combustion ratio and heat-transfer efficiency, temperature and composition of the off-gas, and slag and metal chemistry.IntroductionOne of the anticipated advantages of smelting reduction over conventional ironmaking is the use of lower-grade raw materials. In this work, the effect of-properties of raw materials on the performance of an iron-bath reactor is examined with a numerical model. The model is also used to assess the effect of properties of the blast (flowrate, temperature and oxygen enrichment) and ejected droplets (generation rate, size and ratio of total weights of slag and iron droplets) on the key parameters of the process. In the process coal, oxygen, ore (which may be partly prereduced) and fluxes for specified slag composition are charged to the bath. Slag and iron droplets are ejected from the bath into the gas phase, where they are heated before returning to the bath. Iron droplets undergo decarburisation and reoxidation with CO2 and H2O. Dust is also generated from the bath, and oxygen or preheated air for post combustion is injected from the top of the vessel.The model consists of three modules: 1) reactions in the gas phase and heat transfer from gas to droplets ejected from the bath; 2) heat losses from the vessel and radiative heat transfer from the freeboard to the bath; and 3) heat and mass balances for the bath. The structure of the model and the data exchange between the modules are shown in Fig. 1. The following parameters of the process are calculated: coal, ore, flux and oxygen consumption, postcombustion ratio (PCR), heat transfer efficiency (HTE), off-gas temperature and composition, slag and metal chemistry, and rates of decarburisation and reoxidation of the iron droplets."

Jan 1, 1996

By Matthew John M. Krane

"The macrosegregation patterns and convective behavior of a Pb-5wt%Sb-35wt%Sn alloy are studied using new numerical treatments of solid particle motion and of transport phenomena occurring during the solidification of ternary metal systems. At this composition, the solidification which occurs while the local liquid composition is in the (Pb)-(SbSn) binary eutectic trough has a significant effect on these phenomena. The effects of this solidification path on fluid flow and macrosegregation are compared to the more familiar binary alloy patterns and the effect of solid particle transport is evaluated. The final predictions of macrosegregation are compared to measured composition profiles. IntroductionThe macroscopic maldistribution of alloy constituents during solidification, commonly called macrosegregation, is a defect which occurs in real metal processing systems. This nonuniformity of species distribution, especially when it forms a high composition gradient or a poor distribution of secondary phases, can lead to areas of high stress concentration, which contribute to cracking during extrusion or forging of wrought alloys or when an as-cast piece is severely loaded in service [1, 2]. Macrosegregation studies in binary systems have become quite common since the introduction of single-domain numerical models which feature one set of conservation equations and boundary conditions for an entire, fixed computational domain containing solid, liquid and multiphase regions. A complete review up to 1995 has been presented by Prescott and Incropera [3]. However, most commercial alloys generally have more than two species in amounts significant enough to affect the convective flows which lead to macrosegregation and other defects. The formation of secondary solid phases, including eutectic and peritectic reactions, also may occur in commercial metal alloys and should be treated using appropriate thermodynamic models."

Jan 1, 1999

By A. E. M. Warner

Inco Limited has long and extensive experience in converting nickel-copper primary smelting mattes over a broad range of nickel/copper weight ratios and combined nickel-copper-cobalt contents. At the Copper Cliff Smelter, the composition of the converter product matte has to meet the requirements of the matte separation process; at the Thompson Smelter, converter matte of a different composition is cast into anodes for nickel electrorefining; and in Soroako, Indonesia, a very low copper product matte is granulated for the Japanese market. Recently, Inco has conducted pilot plant testing of three possible nickel-copper matte continuous converting routes, namely flash converting, oxygen top blowing-nitrogen bottom stirring, and tuyere blowing. This test work has generated substantial new information on nickel-copper matte converting chemistry. This overview paper reviews the metallurgy of nickel-copper matte converting, in particular the behaviour of cobalt and the operating conditions required to meet the iron and sulfur specifications of the product matte. The relevant thermodynamic information is used to discuss the industrial data.

Jan 1, 2003

By B. S. -J. Kang, M. A. Alvin, J. M. Tannenbaum

"A load-based micro-indentation technique has been developed for damage assessment and non-destructive spallation detection of TBCs at room temperature. This micro-indentation technology has been further extended to the development of a high temperature (HT) test methodology. Elastic modulus calibration tests performed on Hl 3 Tool Steel to 500°C and Haynes 230 at 1000°C displayed excellent agreement with reported values. Moreover, indentation creep tests of Haynes 230 at 1200°C were found to be in agreement with known creep exponents as well. Finally, a HT thermal flux indentation apparatus was assembled for conducting TBC turbine component testing under high temperature moisture-containing environments (= 50% steam with controlled gas content temperatures up to 1250°C). Description and design considerations of this test apparatus are discussed. Preliminary tests of ReneN5/MCrAlY/APS TBC coupons in steam/air environments with in-situ HT micro-indentation testing are conducted. Furthermore, the coupon is removed and examined for damage assessment at periodical intervals.IntroductionLoad and depth relationships acquired throughout the indentation process provide insight to material mechanical properties such as elastic modulus and hardness. Unloading segment analysis of these load displacement curves are utilized in the acquisition of a material's elastic properties. Yet, indentation tests are complex processes involving contact mechanics, material nonlinearity and even fracture mechanics. Thus exact analytical solutions for these processes are difficult to obtain. As a result, much of the current knowledge regarding the indentation process has been acquired through experimental methods and finite element simulations. Initial efforts by Tabor resulted in the application of spherical indentation to obtain post-yielding stress/strain relationships [1]. Soon thereafter, analytical load-depth relations for elastic indentation were developed [2], yet it was Lure who further derived the explicit relationships for both spherical and conical indenters [3]. Improving upon this, these interactions were later extended to indenters with various geometries by various researchers [ 4]. Additionally, by establishing the linearity of the initial unloading slope within the load-depth curve, a relationship between elastic indentation depth, maximum load, unloading slope and indenter geometry was established [5]. From this a theoretical method by which elastic modulus could be determined was established."

Jan 1, 2011

By C. J. Parradies

During injection into a die, semi-solid metal alloys exhibit a shear-rate, history-dependent flow response. Simulating the injection of a thixotropic material requires that empirically determined boundary conditions and viscosity are specified as a function of both temperature and shear rate history. Experiments were performed using an industrial die casting machine that was instrumented with sensors to measure the pressure and temperature during the injection of a semi-solid aluminum alloy through a tube. This benchmark experiment was used to develop a simulation of the die casting process that could then be applied to more complex die geometries. The results of the experiments were analyzed using the exact, steady state solution for a power law fluid and simulations accounting for slipping at the boundary between the semi-solid metal and the die. Results indicated that the no-slip condition cannot be used to simulate the velocity boundary condition, because the measured pressure is much lower than that predicted by the models. An estimated apparent slip coefficient was introduced to account for the reduced pressure. During some of the experiments, a sudden drop in the measured pressured, prior to decreasing the ram velocity, coincided with observations of segregation in the form of concentric rings visible on the polished surface of cross-sections cut from material remaining in the tube.

Jan 1, 1997

By K. Morsi

Titanium-titanium boride whisker (TiBw) composites are emerging as strong candidate materials for advanced applications within the automotive, aerospace and defense industries. Although increasing TiBw volume fraction improves the specific stiffness and wear resistance of titanium, it is usually on the expense of fracture toughness and ductility especially at increased volume fractions of reinforcements where whiskers interlock. This research addresses strategies for microstructural design that may overcome these shortcomings, by generating titanium composites that are locally reinforced with TiBw through in-situ reaction in segregated regions of the microstructure and separated by ductile Ti matrix. The effect of varying composite reinforcement particle sizes (i.e. size of the reinforced regions) on the pressure-less sintering of these dual matrix composites is discussed. Electric current activation was also used to generate high density dual matrix composites and a new simultaneous imaging and modulus mapping technique was used to characterize these unique microstructures.

Jan 1, 2008

By François Tremblay

It is well known that removal of organic material such ,as Jacquer, paint, plastic prior to melting improves aluminum recovery. In addition to being an important economically, decoating of aluminum scrap has a positive impact on the environment, through better control of gaseous emissions. Most of the existing thermal decoaters for aluminum have been designed to operate with scrap containing a level of organic material lower than 10%. The main field of their present application is for recycling of used aluminum can, where levels of organic material are lower than 4%. Alcan has recently developed a new thermal decoating system in order to extend applications of this process to a much wider variety of aluminum scrap. The new decoater efficiently processes aluminum scrap with a level of organic material up to 50%. This new technology features the use of fluidized bed technology to thermally control the process. This innovative feature improves both performance and control over conventional delacquering systems based on hot air convection. This paper describes the basic principles of the technology and the design of the? first industrial unit commissioned by the Alcan Recycling plant in Shelbyville (TN) at the beginning of 1994. Typical applications and operating advantages are discussed.

Jan 1, 1995

By Kimio Itagaki, Torn Matsumoto, Makoto Ohtsuka, Kentarou Harada

"The structure and hydrogen-absorption properties of LaNis thin films were investigated in the present study. LaNis thin films were prepared by a sputtering method with a radio-frequency power, Ws, of 50 -400 Wat substrate temperature, Ts, of323 -573 K. Nickel content of the films decreased with increasing Ws, however, there was no dependence on Ts. At low Ws and low Ts, amorphous films were deposited. In other conditions, the films were polycrystalline. The films prepared at high Ws and low Ts, or at low Ws and high Ts, exhibited only a (h k · 0) peak in the X-ray diffraction profiles. This indicates that the c-axis of crystalline films was oriented parallel to the substrate plane. At high Ws and high Ts, the films with columnar structure were obtained. Hydrogen-absorption capacity of the thin films increased with increasing Ws. The pressure plateau did not appear on the pressure-composition isotherms. The films deposited at high Ts represented a higher equilibrium pressure.IntroductionThin films of hydrogen storage alloys can be applied for an electrode of rechargeable battery or fuel cell, a filter for H1 purification and various kind of sensor. Some studies on the preparation of the thin films of LaNi5 intermetallic compound, which is a typical hydrogen storage material, have been done hitherto. Adachi et al. , 2) and Sakaguchi et al. 3) prepared amorphous and crystalline LaNi5 thin films using flash evaporation of alloy powders and measured the pressure-composition isotherm for the prepared film utilizing a quartz crystal mass monitoring (QC:MM) method. It was found that the prepared amorphous film absorbed hydrogen without disintegrating into the powders and the hydrogen-absorption capacity of the films increased with the degree of crystallinity. Sakai et al. 4) reported that the maximum hydrogen storage capacities of amorphous and crystalline LaNi5 thin films, fabricated by a RF sputtering method using combination targets, were about 40 mA h g-1 (LaNisHo.7) and 160 mA h g-1 (LaNi5H2.6), respectively. Uchida et al. 5, 6) prepared LaNi5 thin films using flash evaporation of alloy powders and measured volumetrically the pressure-composition isotherm for the prepared film. It was reported that the hydrogen-absorption capacity of the films changed by the annealing treatment."

Jan 1, 1998

By Bo Björkman

A controlled dust generation whereby the dust generated would be enriched with specific metals would considerably facilitate the possibilities of recovering metals from such dusts. A basic understanding of the dust forming mechanisms is of fundamental importance to achieve a controlled dust generation. The present study deals with dust formation in a copper converting process. Dust samples collected from various places in the gas cleaning system were characterised for chemical and mineralogical composition using chemical analysis as well as microprobe analysis. Thermodynamic calculations were used to predict the formation of chemically formed dust at various temperatures and amounts of leakage air to the gas system. The results show that a separation of mechanically formed dust. e.g . Si0:2. Cu and chemically formed dust. e.g .? Ph, Zn, As, Bi. could, to some extent, be obtained due to their different particle sizes. A selective condensation of Pb, Zn and As at various temperatures could. according to thermodynamic calculations, he possible at high temperature. A selective condensation of metals requires an airtight gas cleaning system or a gas cleaning system with a limited amount of leakage air in order to maintain the desired temperature level.

Jan 1, 1996

By H. K. Fouad, L. A. Guirguis

The starting mill strip solution· for this study· is an ammonium uranyl tricarbonate solution of pH 8.2 containing 20g uranium/liter, after a DEPA/TOPO extraction process from sulfuric acid leaching liquor. To the first portion of the concentrated acidified strip solution, hydrofuoric acid is added at 95°C in reduced condition to obtain uranium tetrafluoride. The second portion of the uranyl carbonate strip is subjected to a precipitation step by admixing 0.3 volume of non-solvent precipitating agent such as acetone per volume of uranium. ·Uranium oxide (U30 8) is obtained from this precipitate by calcination for half an hour at 800°C in air. The third portion of the strip solution is neutralized to a pH 6.5 with sulfuric acid to precipitate iron and other contaminants. The solution is further acidified to a pH 1.85 with continuous air bubbling to remove CO2, followed by H2Ch precipitation at pH 3.5 to obtain uranyl peroxide. The latter is reduced by stannous chloride to obtain uranium trioxide dihydrate UO3. 2H20. Identifications, characterization· and purity of these products are carried out by complete chemical analyses, Scanning electron microscope study, tap density determination, X-ray diffraction and infrared spectroscopic investigations. The achieved results agreed well with that of the published data for these nuclear grade purity products.

Jan 1, 2000

By Seyed Mahdi Abbasi, Adel Sheikhhosseini

"This research was conducted to study the changes of microstructure, chemical composition and mechanical properties ofIN718 superalloy after adding aluminum to the ESR process slag. The experiments were performed in VIM and ESR furnaces. The results showed adding 1.5 percent aluminum to the slag increase lave phase in the IN718 samples from 0.34 percent in the base sample to 3.0 percent. It also indicated that the more increase of aluminum in slag cause decrease in the aluminum absorb yield in the superalloy.it is observed that increasing aluminum from 0.7 to 1.1 and then to 1.5 percent caused a decrease of absorb from 91.4 to 76.3 and 74.6 percent respectively due to increasing of aluminum oxidation. According to the results, tensile strength increased and ductility declined in the IN718 samples mainly because of rising the amount of y' volume fraction.IntroductionIN718 superalloy is an iron-nickel base superalloy with constant mechanical properties at medium at high temperatures. For the past seven years a considerable amount of time and effort has been expended by both suppliers and users in the study of Alloy 718 [ 1]. The interest in this material stems not only from the interesting metallurgy associated with the alloy, but with the large usage of the material in numerous applications In fact many people believe that the projected use of this alloy increase significantly over the next several years, The large use of Alloy 718 is the result of its performance in respect to high strength, good ductility, good repair weld ability and from its versatility of being supplied in various product forms. This superalloy is used in wide ranges of industries such as aerospace and gas turbines [2]. In the past more than 20 years many researchers did a lot of work to improve the structure stability of IN718 at high temperatures and intended to develop a new 718 type alloy to be used beyond 650 °C. One of the methods is to control and phase precipitation behavior by means of adjustment of Al, Ti and Nb contents. The other idea is to strengthen the matrix by altering the content of solid solution elements such as W and Co. The adjustment of these alloying elements can change phase precipitation behavior [3]. If detailed information dealing with phase precipitation behavior can be obtained before experimental work for alloy development, a lot of time can be saved and the development cost can also be reduced. In recent years, computer modeling based on experimental data plays an increasing role in alloy design and development. Adding Al to the Iron and Nickel increas the strength of superalloy by formation of y phase and subsequence formation of n phase. Ti in IN718 superalloy also helps the formation of MC carbides and gamma prime phase. Increasing Al/Ti and (Al + Ti)/Nb will lead to form finer particles of y'. More uniform distribution of the precipitates and enhancing stability of y' in IN718 superalloy [ 4]. Adding Al to slag of ESR process can reduce the oxide inclusions because of the strong tendency of Al to oxidation. In addition, tensile properties of IN718 superalloy improve. The most significant inclusions in IN718 superalloy are Alz03 and TiN that were found in agglomerate forms. Thermodynamic calculation results indicate that the effect of increasing Al shows a strong increase in solvus while phase solvus shows mildly decrease when Al level is less than 2%, after that it dramatically decreases [ 5]. Laves phase precipitation and the appearance of phase are occurred when Al content reaches 2%. In fact, when Al content is beyond 1.5%, phase has already precipitated in a considerable scale. Shows the fraction of increases greatly while the fraction of phase decreases remarkably with the increment of Al content. Based on thermodynamic theory, if these particles were not existed in the melt during cooling agglomeration would not accrue and the superalloy will be cleaned By adding Aluminum to the slag, the metal reacts with oxyge"

Jan 1, 2013

By N. Coone

By exploiting the results of solidification modelling foundries can enhance the quality and reduce the cost of their casting processes. However not enough information exists on the thermal boundary conditions, which control the transfer of thermal energy stored in liquid metal to the mould via the metal/mould interface during solidification. This is quantified by the heat transfer coefficient (h.t.c.). An experimental and numerical study was carried out to find the magnitude and variation of the h.t.c. in cylindrical castings during the solidification of grey cast iron in green sand moulds. The h.t.c. values were calculated using a time marching solution to the inverse heat conduction problem. The variation of h.t.c. with metallostatic head was analysed. There is a wide scatter in green sand thermal properties due to the large number of variables involved in mould manufacture including green sand compaction and water content. The sensitivity of the calculation to uncertainties in the thermophysical properties of the green sand was evaluated. Keywords: Heat transfer coefficient, grey cast iron, sand moulds. inverse technique

Jan 1, 2003

By Lauri Holappa

Copper converting is mostly performed in Peirce-Smith converters. The process is still very similar to the original one developed in the early 20th century. It is a batch process in a horizontal cylindrical reactor with air blowing via tuyeres along the length of the reactor side. The Peirce-Smith converter has its roots in Bessemer's inventions in the 1850's as he tested both horizontal and vertical vessels for steel converting. However, for steel making a vertical pear-shaped converter with air bottom-blowing was established. In the course of time, there was a distinct necessity for oxygen usage instead of air due to harmful effects of nitrogen to steel properties and its cooling effect. In-bath blowing of oxygen did not succeed, however, and top-blown oxygen converter with oxygen lance (LD or BOF) was first developed in he 1950's and emerged rapidly to a dominating position. Somewhat later oxygen bottom-blowing via special shrouded tuyeres was developed (OBM or Q-BOP) but has attained only fractional share. Bottom-blowing technique had, however, impact on the current combined blown converters which adopted the benefits of both top and bottom blowing. In copper converting Peirce-Smith type converters have kept their position until today although new processes have been introduced and at least few of them seem to be emerging. In one respect copper converting has a clear leading position i.e. in the progress of continuous converting processes (Mitsubishi, Ausmelt). These processes utilise top-blowing lances instead of in-bath blowing tuyeres. A different principle for continuous converting is flash converting by Kennecott Outokumpu, which makes smelting and converting independent of each others. Solid ground matte is used as a feed for flash converting in a reactor shaft similar to Outokumpu matte flash smelting. A comparable process has been presented by Inco too. The paper discusses principal physico-chemical and process technical similarities and differences in copper and steel converting. Although these processes are metallurgically quite different it seems that during the modem history of ferrous and non-ferrous metallurgy, starting from the 1850's, the exchange of knowledge between these disciplines has been quite intensive. In long-term perspective, many similarities in the development can be found but also divergences due to different ambient circumstances.

Jan 1, 2003