Search Documents

By U. Meyer, A. Alonso, P. Banios

The sampling of cathodes has changed with the introduction of the ISA-process in copper refineries. A Jernkontoret joint working group of refineries and rod plants from both primary and recycled copper plants has been investigating whether the actual sampling of cathodes is representative for this type of cathodes. As a first stage, samples were sent to the members of the working group with the objective to find an easy basis for a comparison of the results of the next stages. All samples show the same tendency for nearly all elements. In some cases, there may exist differences in calibration and for some elements the detection limits are too high, especially when Optical Spectrometry is used. In the second stage, discs were compared with melted samples to answer the question whether the punching of discs is sufficient for the quality control of the cathode. The analyses of the discs represent fairly well the cathode quality. There are differences between cathodes from different crops. Three punches are sufficient to determine the cathode quality. Finally, samples from various lots of cathodes were compared with samples from the rod produced from these cathodes. The impurity content of the rod corresponds to the impurity content of the cathode.

Jan 1, 2000

By W. G. Davenport

Chapter 4 examined Inco (oxygen) flash smelting of pure chalcopyrite concentrate. It showed that the oxygen and flux requirements for auto thermal smelting are readily determined by a matrix calculation. This chapter extends this matrix approach by applying it to a multi-mineral concentrate.

Jan 1, 2001

By Kee Jeung Lee

In this study the characteristic factors and formation mechanisms for the hydrothermal preparation of a -quartz crystal powders were investigated to find the optimum synthetic conditions. The degree of Q -quartz crystal face development depended on the relative growth rate of a particular form that varies considerably with the degree of supersaturation, the reaction temperature, the concentration of mineralizers, and the presence of seed crystals in the feedstock. Alkali hydroxides and alkali halides were found to be effective in the reactions as mineralizers, which added in order to increase the solubility of the feedstock. The fine Q -quartz crystal powders were obtained in the temperature range of 250-450% and pressure range of 100-300atm. As the concentration of mineralizers increased, the particle size of crystalline powders became smaller at lower reaction temperatures. The fractional size distribution of synthetic crystal powders was depended on the hydrothermal conditions. As the reaction time and the amount of seed crystals increased, the width of particle size distribution became narrower. The weight mean particle size was in the range of 1 to 10m. The characterization of the products were carried out using XRD. SEM. PSA, FT-IR, Raman spectrometer.

Jan 1, 1997

By Eltefat Ahmadi

Iron-free titanium oxycarbonitride (TiOxCyNz) is a promising feedstock for production of titanium tetrachloride (TiCl4) at low temperatures. In this study, the effects of leaching variables such as temperature, time, particle size of staring material and concentration of the leaching solutions were evaluated on iron removal from nitrided Malaysian ilmenite by Becher process. The nitrided ilmenite was prepared by isothermal reduction with graphite at 1200 °C for 3 h in H2-N2 atmosphere. The aerated leaching experiments were conducted at 50–90 °C with addition of 0.3–2.0 wt% of NH4Cl catalyst. The highest extent of iron removal (XFe) was obtained at about 96.2% for the sample leached at 90 °C for 7 h with 2.0 wt% NH4Cl. The iron concentrate and titanium oxycarbonitride product were characterized by ICP-OES, XRD, XRF and SEM-EDX analyses. The results indicated that the aeration leaching process was a successful route to prepare low-iron titanium oxycarbonitride.

By Jing Zhong, Yugang Li, Chen Yan, Shaoda Zhang, Qian Wang

Online surface quenching technology has been developed for the hot charging process to prevent the surface cracks in high strength low-alloy steel slabs. In this paper, a two-dimensional heat transfer model of surface quenching process was presented. This finite element model includes nonlinear thermodynamic properties, by which the slab temperature distributions were computed. The model predicted temperatures show reasonable agreement with the measurements. The effects of the water flow rate and slab movement velocity on temperature variation during the quenching and subsequent tempering process were investigated. The result shows that the temperature drop increases but the tempering temperature changes slightly with increasing water flow rate and decreasing slab velocity. Keeping the slab movement velocity at 1.2-2.1m/min and the water flow rate at 55-70m3/h, the slab surface experiences a temperature drop of 400-600 firstly, then recovers above 650, the quenching and energy-saving effect are remarkable.

Jan 1, 2015

By Dengfu Chen, Yunwei Huang, Mujun Long, Kui Lv, Pei Xu, Lin Bai

The surface temperature of continuous casting slab in the secondary cooling zone is a key parameter of production control. However, the accuracy of radiation temperature measurement of high temperature casting slab is greatly affected by the environmental factors, such as water vapor, spray, water film and other participational medias during continuous casting process. In this paper, the radiation characteristics of water vapor and its influences to radiation temperature measurement of continuous casting slab were investigated. Based on the database HITRAN 2004 and the measuring principle of monochrome thermometer & colorimetric thermometer, the measuring errors under different operating infrared spectral wavelength were compared. Results showed that spectral region with wavelength nearby 1.0μm or 1.6μm would be the optimum for high temperature infrared thermometer used under the conditions with moist steam, water spray and water film at the secondary cooling zone in steel continuous casting.

Jan 1, 2016

By John J. Jonas, Sang-Hyun Cho, Ki-Bong Kang

"The recrystallization behavior of Nb micro alloyed steels containing Cr, Mo, Ni and Ti. was studied using hot torsion testing with the aim of modeling the recrystallization processes and the mean flow stress taking into account the microstructural behavior during hot rolling. The kinetics of static and metadynamic recrystallization were characterized and appropriate expressions were formulated for the recrystallization kinetics. These are shown that the recrystallization kinetics depend on steel composition and the processing conditions. The stress-strain curves were determined in order to derive new equations for the peak stress, peak strain, mean flow stress and softening kinetics. The peak strain is influenced by the presence of alloying elements; their addition, which has a solute drag effect, retards the rate of grain boundary motion, shifting the peak to the right. The addition of Nb to the steel results in a significant increment in the activation energy for hot deformation, and Mo has smaller effect than Nb, but Cr has the opposite effect. It was also found that the deformation activation energy in these steels was not altered by the addition of Ni. The rate of metadynamic recrystallization increases with strain rate and temperature and is observed to be independent of strain, in contrast to the observations for static recrystallization.The mean flow stress (MFS) calculations, based on the Sims analysis, are then compared with the predictions of a model based on an improved Misaka mean flow stress equation in which solute effects, strain accumulation, as well as the kinetics of static and metadynamic recrystallization are accounted for. Good agreement between the measured mean flow stresses, which is obtained from the mill logs of POSCO Kwangyang #3 HSM (hot strip mill), and 'predicted ones is obtained over the whole range of rolling temperatures. The results demonstrate that dynamic recrystallization followed by metadynamic recrystallization, supported by the unexpected load drops, sometimes occurs for the rolling schedules studied in the present analysis."

Jan 1, 2001

By M. P. Bohrer

A closed-loop hydrometallurgical process has been developed for treatment of smelter flue dust generated by copper recycling. The process is a semi-continuous operation in which zinc, iron, and copper are first extracted from the dust with a sulfuric acid solution. The lead and precious metals, initially present in the dust, remain as solids and can be recycled to the copper smelting furnace. Cementation with iron and zinc metal purifies the zinc and iron-rich liquid stream prior to spray drying. The spray-dried product, consisting of a mixture of zinc sulfate monohydrate and iron sulfate monohydrate, is a desirable micronutrient additive for use in animal feeds. Treatment of the smelter flue dust in this manner will generate a positive return on investment, as well as mitigate a potential environmental liability.

Jan 1, 1992

By Wenbo Luo, Jilai Xue, Tiepeng Li, Jun Zhu

Sodium silicate solutions for producing silica have been ultrasound treated to enhance the precipitation process in laboratory scale. Higher precipitation rate was found with ultrasound treated solutions than those without ultrasound. The obtained SiO2 powder products were characterized using XRD, SEM, BET and laser particle size analyzer. The particle size distribution and the specific surface area of the powder products varied with the power input level and the processing time of the ultrasonic treatment. The results indicate that the efficiency of the precipitation process can be improved optimally when the ultrasound is conducted into the solutions before the nucleation stage.

Jan 1, 2015

By Susumu Okabe

Mitsubishi Continuous Copper Converter employs the top blowing lance system for the continuous supply of reaction gases into the molten bath. In order to avoid the excessive refractory wear caused by the melt splash without loss of the reaction efficiency, the furnace design and the blowing condition should be optimized. Empirical equations which correlate the splashing rate on the' side wall with the dimensions of the furnace, lance position, lance size, gas velocity and bath properties were obtained by by the physical model study, and compiled into a computer program. The computer program is effectively utilized for the analysis of the actual operation and for the optimum design of new furnaces.

Jan 1, 1998

By Xinghui Meng

The recovery of platinum and palladium from automotive catalysts has been investigated by leaching in iodide solutions with oxidants including oxygen and iodine in an autoclave. An ammonium salt was presented in a neutral leaching solution as a key leaching reagent to achieve high recoveries of the platinum group metals (PGM). The effect of temperature, and concentrations of oxidants and of ammonium salt on the recovery of PGM was examined. Under the experimental conditions studied, the recovery of platinum and palladium was found to be greater than 95%. An economical assessment of this process has also been examined and discussed.

Jan 1, 1995

By Damien Wagner

To reduce the emission of greenhouse gases by the steel industry, particularly for ironmaking, the production of DRI (Direct Reduced Iron) using hydrogen as the reducing gas instead of carbon monoxide is being considered. In this context, the reduction of pure hematite by hydrogen was studied at the laboratory scale, varying the experimental conditions and observing the rate and the course of the reaction. All the reduction experiments were performed in a thermobalance and supplementary characterization methods were used like scanning and transmission electron microscopy, X-ray diffraction, and Mössbauer spectrometry. The influence of rising temperature in the range 550-900°C is to accelerate the reaction; no slowing down was observed, contrary to some literature conclusions. A series of experiments consisted in interrupting the runs before complete conversion, thus enabling the characterization of partially reduced samples. Interpretation confirms the occurrence of three successive and rather separate reduction steps, through magnetite and wustite to iron, and illustrates a clear structural evolution of the samples. Finally, the influence of the sample type was revealed comparing a regular powder, a nanopowder and a sintered sample. The regular powder proved to be the most reactive despite its larger grain size, due to a more porous final structure.

Jan 1, 2006

By Batric Pesic

Dissolution of gold with sodium bromate solutions of various compositions was studied by using a rotating disc technique. The role of bromide ion, acid and externally added bromine was examined. It was found that sodium bromate could not dissolve gold in the absence of either acid or bromide ion, or both. When acid was absent, no bromine necessary for gold dissolution could be produced. When bromide ion was absent, formation of soluble gold bromide species, AuBr,-, was not possible. Bromate concentration had a complex effect, and it was dependant on bromide ion concentration. For fixed initial bromide ion concentration, gold dissolution rate increased with sodium bramate concentration increase until certain level, beyond which further increase of bromate concentration decreased the gold dissolution rate. The negative effect of bromate was explained by the depletion of necessary bromide ion. Sulfuric acid concentration effect was a function of initially present bromine.

Jan 1, 1992

By Elli Nurminen

Sulphate decomposition was studied in the conditions of a typical copper flash smelting heat recovery boiler. The aim was to determine the kinetics of the copper sulphate decomposition reactions and to find out if they are likely to take place in the process conditions prevailing in an industrial HRB. The information is essential in CFD-modelling of the reactions taking place in the boiler and for optimising the process. Thermal decomposition of sulphates was studied by thermogravimetry. The experiments were conducted with a commercial copper sulphate, a partially sulphated copper oxide and an actual process flue dust. The main variables studied were temperature and gas composition of a N2-O2-SO2-mixture. The samples were characterized with SEM, optical microscope and XRD. Temperature affected the decomposition rate strongly but the gas composition had a minor effect on the kinetics. The decomposition was fastest in the partly sulphated oxide and slowest in commercial copper sulphate. Keywords: Sulphate decomposition, flash smelting, heat recovery boiler, flue dust

Jan 1, 2004

By Maria D. Salazar-Villalpando, Anthony Cugini, Bryan Reyes

"The electrochemical reduction of CO2 was performed in a laboratory-made, divided Htype cell. A copper electrode was used as the cathode. An Aldrich Nafion 117-type ion exchange membrane (0.18mm thickness) was used as the diaphragm. NaHCO3 and KHCO3 were studied as the catholytes. Hydrogen evolution from water reduction and products from CO2 electrochemical conversion were recorded. Higher CO2 reduction enhancement was observed by KHCO3 as compared to NaHCO3. The main conclusion of this work is that in fact CO2 can be electrochemically reduced with copper electrodes.1.-INTRODUCTIONThe direct electrochemical reduction of CO2 may allow for a simple process and, by avoiding high temperature reactors, would enable the process production rate to be quickly varied to follow the time of day availability of surplus electricity [1]. Temperature has a major effect on the electrochemical conversion of CO2 since its solubility increases when temperature decreases [2]. The electrical potential applied to the electrochemical reacting system will have an influence on the product distribution, as well. For example, a narrow potential range during cyclo-voltagraphic studies will determine the detection of a lower number of products. A recommended potential range to study the electrochemical reduction of CO2 is -2V to 2V. Moreover, the reaction rate on the electrode is governed by various processes, such as the kinetics of electron transfer, adsorption/desorption at the electrode surface, and diffusion of CO2 to the Cu electrode. The availability of active species, CO2 for electro-reduction, is extremely low at the vicinity of the electrode surface and it seriously interferes with the rate of mass transfer. In batch type electrolytic reactors, depletion of CO2 at the surface takes place first. CO2 from the bulk then has to diffuse to the electrode surface, resulting in mass transfer controlled kinetic phenomena. During the above process, several other competitive side reactions could suppress the primary reaction even though the cathode has good electro catalytic properties for reduction of carbon dioxide. When the dynamic supply of specific active species is ensured to electrode surface, the mass transfer effects are minimized to certain extent. Hence it is envisaged that a continuous flow reactor is more efficient for the electro-reduction of CO2 in CO2 saturated aqueous electrolytes. The primary reactions that occur at the copper electrode during the reduction of CO2 are listed below (with the standard potentials calculated using formation energies [1] :"

Jan 1, 2010

By Toyohisa Fujita

The effect of variables on the gold extraction with ammonium thiosulfate was investigated on sponge gold and ore samples. The Effects of CUS04, (NH4hS203, NH40H, (N~hS04' pH, stirring speed and retention on gold leaching rate and thiosulfate oxidation (consumption) have been studied. Almost 100% of gold was leached from sponge gold and over 96% from ore sample at optimum conditions. Trioctylmethyl ammonium chloride was used to recover gold from thiosulfate pregnant solution. It was found that more than 99% of gold was recovered by the extractant diluted with n-octane at 01 A ratio of 1: 1 without the re-adjustment of pH or others. Also, the gold cementation was conducted without de-aeration by using zinc, copper and aluminum powders. The result indicated that the gold was effectively recovered from a solution of low ammonia and copper concentrations and higher thiosulfate concentration. The gold recovery process by using ammonium thiosulfate is an environmental friendly method comparing to conventional cyanidation process.

Jan 1, 2003

By B. C. Blakey

The economic feasibility of the sulphuric acid pressure leaching route for the extraction of nickel and cobalt values from limonitic ores is highly dependent upon the behavior of aqueous aluminium. This is primarily due to its precipitation as hydronium alunite ((H30)A13(S04)2(OH)6), which is one of the major scale-forming compounds found in autoclaves used for pressure leaching. As a result of renewed interest in the pressure leaching process, an investigation of the aqueous-solid eqilibria in the aluminium-sulphate-water system under acidic (< pH l), high temperature (230 to 270°C) conditions has been conducted. Pure hydronium alunite was synthesized in an autoclave by leaching boehmite (A100H) at elevated temperatures in sulphuric acid solutions initially 0.25 to 0.75 m H2S04 in concentration. Spontaneous, in situ precipitation of hydronium alunite followed. A high temperature solution speciation model was used for the analysis of the resulting solubility data in order to calculate equilibrium constants for the precipitation reaction.

Jan 1, 1994

By F. Qian

Direct impingement of molten metal baths by a gas jet is commonly encountered in such processes as BOF and electric arc furnace steelmaking. Shape and local fluid mechanics in the impinging region is important because it determines the interaction of the metal pool with the surroundings. Goal of the present work is to characterize and understand the interfaces at the impinging region. Using a physical model consisting of water/corn oil and water/kerosene as surrogates for metal/slag, interface shapes for slag-gas, slag-metal and metal-gas are investigated. Influence of transport properties of the two liquids on the shape and flow fields are also experimentally determined under various impinging jet conditions, namely jet momentum and jet height. The viscosity of the slag layer (corn oil or kerosene) has the most significant effect on the interface shape and the induced flow fields. The interface shapes were measured both photographically and by using a surface- tracking resistance probe. The limiting condition at which the jet breaks through the corn oil or kerosene layer and reaches the water layer was determined experimentally

Jan 1, 1994

By Guo Gongyi

An extraction chromatography by which 99.99 % pure scandium oxide can be prepared from the starting materiel containing about 70% scandium oxide has been developed by taking advantage of some peculiar properties of the complex chemistry and extraction chemistry of scandium. The purification of scandium was performed at room temperature with relatively fast rates in two chromatographic columns. The preliminary separation of scandium from impurities was done by extraction chromatography using tri-butyl phosphate as the stationery phase in the presence of citric acid, and the nearly complete separation in the presence of perchloric acid. The scandium recovery was greater than 90 %.

Jan 1, 1989

By Kandipati Sreenivasarao

A promising method for removing heavy metal ions from dilute effluents is ion- or precipitate- flotation, in which a suitable collector is added to form hydrophobic metal-collector complexes or compounds that can be collected as foams. We have successfully removed Cu(II), Cd(II), and Pb(ll) from dilute solutions using sodium dodecylsulfate and ethanol as collector and frother respectively. However the process would not be economically viable unless the collector could be recycled, and the heavy metals recovered in a concentrated, preferably marketable, form from the foams. We investigated four different methods to decompose heavy metal-dodecylsulfate complexes, namely precipitation of hydroxides, precipitation of sulfides, chemical stripping, and electrolysis. We compare the performance of these methods. In each case the observed behavior is related to known thermodynamic data, and potential applications are discussed.

Jan 1, 1995