Search Documents

By Samir N. Shoukry, Mourad Y. Riad, Gergis W. William

"Setting of concrete material is defined as the transitional period between states of true fluidity and true rigidity. Initial and final setting times are measured in the laboratory on the mortar sieved from the mix in a controlled environment where temperature and moisture values are constant. On the other hand, field applications are held in outdoor environments where environmental variations have direct impact on setting time values. In this study, initial setting time of class K concrete, usually used for bridge decks and concrete pavements, are investigated highlighting discrepancies between laboratory and field measurements. 72 mixes have been cast in variable environments and collected data from concrete mixes and the ambient conditions are reported. In light of the collected data, the effects of variable setting times on early age cracking of concrete material are studied and means to minimize such cracks are presented.BackgroundSetting of concrete material is defined as the transitional period between states of true fluidity and true rigidity [1]. Continuous hydration of the cement within the matrix transfers the mix from a state of setting to hardening. Initial and final Setting times are measured in a laboratory setting following ASTM C 403 specifications. Initial setting approximates the time at which the cement paste can no longer be plastic under compaction (or can be handled in a proper fashion), while the final setting approximates the time at which hardening occurs. The standard test described in ASTM C 403 is conducted on the mortar sieved from the mix (paste passing from 4.75 mm sieve opening). Initial and final settings are described as the elapsed time after the initial contact of water and cement till the mortar reaches a penetration resistances of 3.5 MPa (500 psi), and 27.6 MPa (4000 psi) respectively."

Jan 1, 2012

By W. Y. Kim, K. H. Song, K. Nakata

"The present study was carried out to evaluate the mechanical properties of friction stir welded Inconel 600/SS 400 lap joints. In this process, friction stir welding (FSW) was performed at a tool rotation speed of 200 rpm and welding speed of 100 mm1min, and argon gas was utilized to prevent surface oxidation during the welding. Application of FSW notably decreases the grain size of Inconel 600 alloy from 20 µm in the base material to 8 ~ in the stir zone. However, the grain size of SS 400 in the weld zone was slightly coarsened, when compared to the base material. Also, the hooking in the advancing side and the intermetal1ic compounds (M7C3) in the weld interface between Incone1 600 and SS 400 were well formed. These intermetallic compounds and hooking were effective to increase in mechanical properties such as tensile and peel strengths.IntroductionFriction stir welding (FSW), applicable welding process at solid state, has several advantages in defect suppression such as blow hole, segregation and cracking which mainly occurs in fusion welding [1, 2]. Notable grain refinement in the stir zone due to FSW can expect the outstanding increase in mechanical properties of the welds. In constructing the chemical and power plants, Ni base superal10ys have been used in many parts, moreover, fusion welding as construct method, such as gas tungsten arc welding, electron beam welding and laser welding, has been mainly used [3-5]. However, fusion welding has a limit in an increase in chemical and mechanical properties in the welds. Lately, Ni base superalloys to which FSW applied have been reported with notable enhancement in mechanical properties, which resulted from refined grains in the welds [6-10]. These researches showed the possibility in applying the FSW, directly."

Jan 1, 2012

By Nedam Abed

A fundamental study of the sonochemical leaching of chalcopyrite in ferric ion media has been performed to understand and quantify the effects of sonication and other parameters on leaching reactions. The study covers sulfate and chloride media. The main leaching reaction: CuFeS2(s) + 4Fe3+(aq) Cu2+(aq) + 5Fe2+(aq) + 2S(s) (1) was found to be dependent on temperature and initial particle size, but less dependent on ferric ion concentration. Leaching kinetics were not affected by ferrous ion concentration or the amount of chalcopyrite added. Leaching was performed under a variety of sonication and leaching conditions. Reaction stoichiometry was confirmed through detailed wet chemistry analysis and mass balance calculations. The use of ultrasound activation showed a clear improvement in leaching kinetics and amount of copper extracted, sonication having a catalytic-like effect on the leaching reaction. Compared to experiments without sonication, reaction rates were 2-3 times faster at the same temperature, and could be faster by a factor of 20 for the same initial particle size. Regardless of initial particle size, the amount of copper extracted was comparable under sonication, and could be twice that under chemical leaching, implying the avoidance of fine particle grinding. Sonochemical leaching was found to be only temperature dependent, where the best copper extraction was at 75C. Leaching was further enhanced by the use of a grinding aid. The leaching behavior of chalcopyrite particles remained similar with and without ultrasound activation, implying that the known passivation mechanism in the oxidative leaching was not eradicated. Sonication resulted in coarse particle breakage (ultrasonic milling). Sonication did not contribute to particle passivation, as affirmed from different leaching procedures and sonication in aqueous and organic media. Parabolic leaching kinetics were confirmed for leaching experiments.

Jan 1, 2003

By Thomas Brynjulfsen, Merete Tangstad

"Manganese ore fines, generated during mining and transportation, can not be added to the submerged arc furnace directly as they will prevent even gas flow through the burden. Low gas permeability in the burden will lower the degree of pre-reduction of ore and subsequently increase the carbon and energy consumption of the process. In order to utilize manganese ore fines in the furnace they are agglomerated into sinter, pellet or briquettes. The agglomeration process will however change the reduction properties of the ore. In this work the melting and reduction properties of sinter has been investigated.The melting temperature and melting mechanisms has been studied. The mineralogy of the raw ores and agglomerated has been found using XRD, and the composition established using EPMA(WDS). The effect of adding fluxes such as dolomite and quartz has also been investigated.IntroductionManganese metal is produced in a submerged electric arc furnace or in blast furnaces. The reduction of manganese oxide in blast furnace has in the recent years become more unusual due to the high consumption of reducing carbon material[5]. Manganese metal for alloying in steel usually contains silicon and iron, and are therefore called ferro manganese and silicomanganese.During mining, transportation and handling the manganese ore is broken up into different size fractions. The larger lump are used directly in the electric arc furnace, but the finer materials can not be added without treatment. The fine ore can disrupt the flow of CO and CO2 gas through the burden, subsequently reducing the degree of pre-reduction. The fine fractions must therefore be agglomerated into larger lumps, in order to promote gas flow. This can be achieved through a number of different processes. The agglomerate used in this work has been sintered, which means that is has been partly molten and reduced, in order to create bigger lumps."

Jan 1, 2012

By Fu-Shen Zhang, Mengjun Chen, Jianxin Zhu

"In the present study, different types of cathode ray tube (CRT) glasses were examined by sequential extraction combined with TCLP to provide possible explanations for how Pb and Ba leach out from the waste CRT glasses and to give possible reasons for why they leach out. Sequential extraction results showed that Pb and Ba in the CRT glasses dominanfly presented as the residual fraction. The exchangeable fractions of Pb and Ba were extremely low, less than 0.01 % of the total content, but they were higher than those required by the regulation limits, 5 and 100 mg/L for Pb and Ba, respectively. TCLP tests of the original CRT glasses and CRT glasses residues after each step of sequential extraction demonstrated that the extremely high leaching toxicity of CRT glasses mainly caused by its exchangeable and carbonate fractions of Pb and Ba.IntroductionIn recent years, the amount of cathode ray tube (CRT) contained monitors or TV sets in the market were sharply reduced, since they were substituted by novel and better electronic and electric equipments such as LCD and PDP, leaving huge amount of end-of-life CRTs. 50-85% of the total weight of this kind of computer monitor or a TV set is glass[1,2], which was classified to three categories according to their chemical compositions: black & white glass (BW), color panel glass (CP) and color funnel glass (CF)[3]. In order to provide shielding from X-rays generated during the picture projection process, lead, barium and strontium oxides were used in the glass. In general, a color CRT contains 1.6-3.2 kg of lead . Therefore, these glasses have attracted wide and tense attention due to the potential risk to the environment and human health."

Jan 1, 2011

By K. Verbeken, E. Wettinck, M. Verhaege

Iron (III) can easily and selectively be removed from acidic sulphate solutions with organo-phosphoric acids like Di-2-Ethyl-Hexyl-Phosphoric Acid [D2EHPA]. Stripping of the iron (III) loaded organic, however, is difficult unless highly concentrated inorganic acid solutions are used. In this paper results are shown for the enhanced stripping of iron from loaded D2EHPA by electro-reduction. The loaded solvent is contacted with a 2 M H2SO4 solution, which is continuously recycled in an electrochemical reactor where iron (III) is reduced to iron(II). As iron (II) is not extracted by D2EHPA, the equilibrium for iron (III)- D2EHPA is shifted towards the aqueous iron (Il)-sulphuric acid solution. The electro-reduction unit is a vessel with separated catholyte and anolyte chambers. The catholyte is the actual stripping solution where iron (III) is reduced to iron (II) on a stainless steel electrode. The anolyte is a 2 M H2SO4 solution where oxygen is evolved on a lead alloy electrode. A sintered glass plug separates the compartments. With this unit, enhanced stripping of iron from the solvent is possible under mild acid conditions [2 M H2SO4], and a concentrated ferrous sulphate solution can be obtained. The results shown have mainly been obtained by studying the parameters affecting the electro-reductive stripping of a D2EHPA loaded organic phase in a batch reactor. From an iron (IH)-saturated 20 vol. % D2EHPA solvent containing ~ 12.5 g/1 Fe (III) over 90% of the iron can be stripped in one stage with a 2 M H2SO4 solution at 50°C. It is shown that in this way it should be possible to obtain a concentrated ferrous sulphate solution which can be processed downstream to recover a pure iron product.

Jan 1, 2000

By Carlos Eduardo Gomes de Souza, Luis G. S. Sobral, Paulo A. Medeiros da Silva, Selma G. F. Leite, Renata de B. Lima

"The use of mixed cultures of acidophilus microorganisms that act in different temperature ranges, aims at speeding up the digestion of chalcopyrite, highly refractory sulphide mineral, the major mineral in the flotation concentrate of Caraíba Mining Co., with an attractive processing cost. The concentrate under consideration contains mainly chalcopyrite (CuFeS2) and bornite (Cu5FeS4) with contents of, approximately, 70 and 30%, respectively. It was observed in this study, the performance of consortium of mesophiles, moderate and extreme thermophile microorganisms, in the oxidation of the aforementioned sulphides minerals, evaluating operational parameters such as pH of the leaching solution, the reaction temperature and redox potential, with consequent extraction of 80% of the concentrate copper content within 60 days of bioleaching. Such high copper extraction was achieved in column bioleaching tests.INTRODUCTIONThe solubilization of metals by the application of microorganisms from the mineral ores and the subsequent recovery of metals from solution are referred to as bioleaching (Rohwerder, T et al, 2003). This is an economical method for the recovery of metals from minerals; especially lowgrade ores, overburden, and waste from current mining operations which requires moderate capital investment with operating cost (Watling, 2006).Furthermore, bioleaching is generally more environmentally friendly than conventional metal recovery processes such as concentration and smelting. Those physicochemical metal extraction processes generate sulphur dioxide, a toxic emission that is increasingly the target of regulatory legislation (Stott et al., 2000; Olson et al., 2003). Bioleaching of chalcopyrite is the key industry target. The main problem hindering commercial application of chalcopyrite bioleaching is the slow dissolution rate (Fu et al, 2008).Dissolution of acid-soluble sulphide minerals such as sphalerite, and to a lesser extent chalcopyrite, occurs by a combination of ferric iron and proton attack via the polysulphide pathway (Rohwerder et al., 2003)."

Jan 1, 2008

By Dinabandhu Ghosh

The stability diagram of the ternary system Ti-C-O is drawn in the present work for four temperatures, 1473 K, 1573 K, 1673 K and 1873 K, showing the stability fields of TiC, Ti, TiO, Ti2O3 and TiO2. An analysis of the system reveals that it is not possible to produce Ti in a carbon-saturated system; instead, the stable product is TiC. However, Ti can be an equilibrium product in a carbon-unsaturated system at prohibitively low values of pCO and pCO2; for example, at 1873 K, these limiting values are: pCO = 10-6.76 atm and pCO2 = 10-13.36 atm, which, when exceeded, produce TiC and TiO respectively. The magnesiothermic reduction is examined through the stability diagram (log pO2 vs. 1/T) of the system Ti-Mg-O, drawn for a number of pMg values, presenting the pairwise stability fields such as Mg(l) + Ti(s), Mg(v) + Ti(s), MgO(s) + Ti(s), etc. The diagram shows that magnesium reduction of TiO to Ti is possible only at T < 1641 K with pMg = 1 atm and only at T < 1569 K with pMg = 0.5 atm. An experimental scheme for Mg vapor reduction of TiO2 is proposed in which an argon stream is passed over a Mg(liquid) evaporator at temperature T1 (say, 1234 K); the resulting Ar-Mg mixture at 1 atm is subsequently flown over a bed of TiO2 at temperature T2. A thermodynamic analysis establishes that complete reduction to Ti is possible and that the best results are obtained when T1 = T2.

Jan 1, 2006

By Tracy Morris, Weldon Read, Luis Navarro

"During the leaching of anodic slimes, tellurium dissolves into the leach liquor together with copper and must be removed before the solution is sent to liberator cells for copper recovery. Prior to the installation of autoclaves, tellurium was precipitated using raw slimes that caused a recirculation of tellurium in the leaching circuit. After autoclaves were installed the old leach tanks were converted into tellurium reactors utilizing copper chips, steam and agitation to form a copper telluride precipitate. Tellurium levels of less than 10 rng/L are achieved in a timely manner.IntroductionThe electrolytic refining of copper consists of an electrolytic cell provided with an anode of impure copper, a cathode of substantially pure copper (starter sheet) and an electrolyte made of copper sulfate and sulfuric acid [1]. When a direct electrical current is passed between the anode and cathode inside the cell, the impure copper anode dissolves in the electrolyte and pure copper is plated onto the cathode. During this operation, many of the impurities are deposited on the bottom of the cell as an anodic slime residue composed of insoluble chemical compounds. Slimes are a major source of rare and precious metals in the copper industry [2-5],In the Amarillo Copper Refinery (ACR), the anodic copper slimes are sent to the Precious Metals department in order to extract and then refine the gold, silver, platinum and palladium from them. The remaining impurities, in the form of a soda slag or copper slag are sent to the Hayden smelter for further processing. Copper telluride is sent to the Selenium/Tellurium department inside the plant for selenium and tellurium recovery. During the leaching process of the anodic slimes, copper, tellurium, and other metal species in the slimes are dissolved into leach liquor that cannot be returned to the tankhouse unless the tellurium concentration is below 10 mg/L."

Jan 1, 2012

By José Sancho, Julia Ayala, Purificación García, Begoña Fernández

"A study is carried out to see the adequacy of using flying ashes coming out from a Power Station to eliminate the copper present in waste cyanide waters that are generated in gold mines.Tests were carried out to see how effective the use of ashes taken from two Power Stations could become. Later, the tests are made using ashes coming from Narcea Power Station as this station is near the mine under study.The work is centred on looking for an economically adequate solution to close the waste decanting ponds of the mine. After several tests, a solution is reached through filtration in static layers.IntroductionThe use of coal to adsorb some water-soluble substances has been widely studied [1,2,3,4,] both in the treatment of drinking waters and in determined stages of selective detachment of cyanide gold complexes in cyanide lixiviation processes [5]. Flying ashes sent to the atmosphere by Power Stations as a sub-product of the combustion of this combustible are generally made of more of a 70 % of a vitreous aluminosilicated material and of an active residual material which may be changeable making them potentially useable as adsorbents. Nevertheless, the properties of each kind of ashes depend on the characteristics of the Power Station, of the combustibles being used, of the combustion system, etc.The aim of this work is to demonstrate the adequacy of flying ashes to eliminate the copper present in cyanide waters coming from gold mines either by adsorption or precipitation of the metal. For this study, tests are carried out with Asturian ashes which have a low quantity of lime. The results obtained in the tests demonstrate the effectivity of the method used. To be absolutely concrete, the work is carried out to establish the use of these ashes in the closing of Asturian installations of cyanide lixiviation"

Jan 1, 2008

By Chu Yong Cheng

The solvent extraction (SX) processes of the three pressure acid leach (PAL) nickel plants in Western Australia have been reviewed. The use of intermediate precipitation, solids/liquid separation and re-leach in the three W A nickel plants make these processes complicated and costly in capital and ?operation. The research work carried out by the SX group at the AJ Parker Cooperative Research Centre for Hydrometallurgy I CSIRO Minerals has led to the development of direct solvent extraction (DSX) processes to recover and purify nickel and cobalt from leach solutions. The simplicity of the process flowsheets and the expected savings in capital and operating costs are the major advantages of the new DSX processes over the reviewed processes. By using a new synergistic organic system in semi-continuous tests with a pilot plant leach solution (after iron precipitation) from BHP-BiIliton Stainless Steel Materials, the metal values (Ni and Co) together with zinc and copper were separated from the major impurities (Mn, Mg and Ca, together with Cl) in the first SX circuit. The co-extracted manganese, magnesium and&apos; calcium were easily scrubbed out. After stripping, the metal values (Ni and Co) together with zinc and copper were concentrated, resulting in a much smaller second SX circuit and equipment in the down stream processes. The extraction and stripping kinetics of the metals with the new synergistic organic solution were very fast. The extraction and stripping almost reached steady state within 0.5 minutes. Semi-continuous test work with a synthetic leach solution, a cobalt pilot plant leach solution from Peko Rehabilitation Project Pty Ltd and a synthetic solution to simulate a concentrated laterite leach solution from BHP-Billiton Stainless Steel Materials showed that manganese, calcium, copper and zinc can be effectively and efficiently separated from nickel, cobalt and magnesium by extraction, scrubbing and stripping. This led to the development of another DSX process using D2EHPA to recover nickel and cobalt from leach solutions.

Jan 1, 2003

By A. V. Tarasov, S. D. Klushin

493 The most common method for minimizing the copper content of residual slag in the process of autogenous smelting of sulfide raw materials is treatment of molten slag in an electric furnace, with optional addition of solid reducing agents, such as coke, and/or sulfiding agents such as pyrite. A drawback of this technique is the fact that the final slag produced still contains 0.5% or more Cu. We have tested a method for treating molten slag obtained as a result of autogenous smelting by a gaseous mixture of sulfur dioxide and methane at a ratio of. SC:SO2 = 0.75 :1.0 in the presence of oxygen. Interaction reaction within the SO2-O2-CRi system proceeded at a high rate at 1373 to 1573 K to form reducing and sulfiding agents: H2S, S, COS, CO, CO2, H2, H2O. The gas mixture requirement was about 100 to 150 Nm3 per 1 tonne of slag. A decrease in the ferric iron concentration (Fe3+) from 10-15% down to 2-3% resulted in lower solubility of copper in slag, and agitation of the melt with gas stream accelerated. the separation of the sulfide phase and slag. Removal of copper from slag was performed in a pilot unit within the second V anyukov furnace zone where slag arrived with a copper content of 0.8-1.3%. The temperature of molten slag was maintained within 1523 to 1573 K. The copper content of the final slag was at a level of0.12 to 0.14%. The matte sent to converting was a mixture of bottom matte from the smelting zone and the slag treatment zone. It had a copper content of about 50 to 55%. Process gases from both furnace zones were combined and sent to the acid plant for sulfur recovery. This process was offered for commercial use at two copper smelters in Russia and CIS.

Jan 1, 2000

By Jian Pan, Zhen He, Deqing Zhu, Shouyan Yue

"The differences of raw material characteristic among six kind of iron concentrates and the influences on ballability were studied from the aspect of the size distribution, specific surface area and particles morphology. The results show that the specific surface area of iron concentrates has crucial influence on ballability, and the effective method of improving ballability for weak ballability iron concentrate has been found. It is of important guidance for Chinese steel mills to import and use iron concentrate from the whole world.IntroductionChina's steel industry has developed rapidly in recent years, crude steel production in 2011 is an unprecedented 683 million tons, which is almost half of the world crude steel production, and it is equivalent to the total sum production of the nations which rank at 2,3,4,5 and 6 in the world [1]. In order to match the development of steel industry, the blast furnaces are becoming larger and more modernization, therefore charging burden of higher quality is requested, and the reasonable blast furnace burden structure is more and more important, at the same time, for iron ore powder sintering process's continuous improvement and development, another method providing ""concentrate"" for blast fumace-pelletizing is also taken seriously. The grate-kiln method of pelletizing has achieved great development for its unique advantage, and in just a few years, there are over 60 rotary kiln production lines have built or being built in China, the sum of pellets has reached to more than 140 million [2, 3]. The rapidly growth of pelletizing yield demands diverse source of pellet, which include not only domestic magnetite concentrate, but also imported hematite which is high in iron and low in silicon. Usually the ratio of imported hematite concentrate increased gradually. The imported hematite concentrate has high grade and fine particle size (the content of -0.074 mm mostly higher than 90%), but the ballability of part of the concentrates is poor."

Jan 1, 2013

By Caisa Samuelsson, Fredrik Engström, Bo Björkman, Margareta Lidström Larsson

"Large amounts of by-products are generated by the Swedish steel industry each year. The EAF-process generates about 400 000 ton of slag, from which 80% is deposit. An alternative to deposit is to use slag as road construction material. However, metal content in the slag can be a problem, due to the leaching. The aim of this work was to investigate how stable these materials are when ageing and kept outside. Five different EAF-slags from domestic steel plants were used in this study. The materials were characterised after 0, 6, 12, 18 and 24 month to evaluate the ageing process. Scanning electron microscope (SEM), x-ray diffraction pattern (XRD) and a standard test for leaching were used. The changes in behaviour differ between the five materials. The total leachability decreases with time for all samples. CaCO3 is formed on slag surfaces as CaO reacts with moister and CO2 in the air. Introduction The slag generation in the Swedish steel industry is about 1.5 million tonnes annually, of which more than 500 000 ton is generated in EAF (Electric Arc Furnace), AOD- (Argon Oxygen Decarburization) converters and during the refining of steel in the ladle metallurgy. Some of the slags are used in different applications, but most of the steelmaking slags produced in Sweden are landfilled today. The chemistry, mineralogy and physical characteristics of slags make it a suitable material in construction, replacing for example, gravel and rock [1]. In some respects, in road construction, it may even be technically superior to virgin material. Slag from scrapbased steelmaking is used for road construction in Europe. The reason for the low utilization in Sweden is mainly due to potential leaching of harmful elements, legislations and competition with easily available natural raw materials. Except the potential leaching, the technical obstacles for not using some slags in construction include:"

Jan 1, 2008

By E. Kuzeci, R. Kammel

"Lately various voltametric methods have gained increased attention as an analytic tool in hydrometallurgy. Voltammograms with mercury drop electrodes or glassy carbon electrodes provide information about the electrocrystallization of cathodic deposits and allow calculation of kinetic data by means of characteristic parameters like the peak potential and peak current and their variation with the voltage scanning rate.Cyclic voltammograms are also suitable for identification of reaction sequences. Voltammograms with carbon paste electroactive electrodes containing metal sulphide additions reveal information about the dissolution behavior. The stripping voltammetry can be applied to analyze metal ions and organic additives (e. g., thiourea) in extreme low concentration. Typical application of the various methods studied with microcomputer controlled measurement system are explained by examples selected from copper hydrometallurgy.IntroductionThe use of electroanalytical methods in metallurgical process control can be dated back to the starting period of industrial copper refining, when the deposition of the metal ions was followed electro-gravimetrically by weighing the electrode with deposits (1). The principles of metal deposition and dissolution have not changed but the methods to follow these phenomena were subjected to noticeable developments and especially the introduction of polarographic investigations by Heyrowsky (2) has greatly contributed to the progress in electro-analysis. A review about the fundamental work on the electrochemical kinetics in earlier time is compiled in a monograph of Vetter (2). With the steady improvements in the instrumental techniques, it is nowadays possible to apply several current and potential modulations for measurements with improved selectivity and sensibility. There is however, still a lack in theoretical interpretation of the data obtained. More theoretical information are already available for linear voltametric methods for systems where reduced as well as oxidized species are dissolved in the electrolyte (4, 5). Some recent investigations have also shown the reliability of these techniques to study electro-crystallization (6, 7). Main fields of the application in the hydro - and electro-metallurgy are:"

Jan 1, 1989

By Batric Pesic

A hydrometallurgical process for recovery of Zn and Mn from Bunker Hill Water Treatment Plant sludge was developed. The process is unique because it treats an unusual combination of metals, Zn and Mn. Another non-standard feature of the process is that leaching takes place with ~S04 in the presence of a reductant (SO2). Zn and Mn are recovered simultaneously by electrowinning, Zn on a cathode and Mn on an anode, as MnO2 The major purpose of the process is to detoxify the sludge by removing toxic heavy metals. The recovered metal values could be marketed to offset the overall costs of water and sludge processing. This work is presented in two separate parts, 1. Leaching and Solution Purification, and II. Electrowinning. This paper covers only the first part of the hydrometallurgical process: Leaching and Solution Purification. Initially, the paper briefly discusses the history of the pollution problem at the Bunker Hill Superfund Site, the origin of heavy metals in the mine waters, and the development and use of the water treatment plant. The leaching of sludge was examined as a function of the following parameters: constant vs. initial pH, initial vs. delayed addition of SO2, temperature, and pulp density. It was found that leaching with H2SO4 at pH 2.0 for 15 minutes (at 60°C), followed by S02 addition for another 15 minutes, could completely dissolve Zn and Mn. Solution purifIcation was done in three stages. In the first stage iron was removed by adjustment of pH (to pH 5.0) and oxidation offerrous to ferric iron (with H2O2). In the second stage, Cu and Cd were removed by Zn dust cementation. Finally, Co and Ni were precipitated with the organic reagents 1-2 nitroso-naphthol and nitroso, respectively. Electrowinning of Zn and Mn is discussed separately in Part II of this paper.

Jan 1, 1996

By Ragnhild E. Aune, Shahid Akhtar, Reza Beheshti

"The potential use of Black Dross (BD) as a raw material for the production of refractories, fluxing agents and glasses is the main motivation of the present study. Heat treatment experiments were carried out in Ar, and under reduced pressure (20 Pa), to evaluate the salt removal efficiency. The chemical composition of the BD after heat treatment was investigated by SEM-EDS and XRD analyses. Based on the present results, it is established that the salt starts to evaporate at ˜1273 K in Ar, and under reduced pressure. The salt removal efficiency in a 20 g sample was found to increase in both cases as a function of time and temperature. Moreover, in Ar the chlorine concentration was lowered to 0.3 wt% after heat treatment at 1523 K for 10 hours. Under reduced pressure, however, 0.2 wt% residual chlorine was obtained after 8 hours at 1473 K.IntroductionIt is believed that aluminum recycling in the near future will become the main route of aluminum production [1]. Black dross (BD) that is produced during this process contains, among other things, high amount of salts like NaCl and KCl [2, 3]. Almost 800,000 tons of BD is annually land filled in United States and this number continues to grow with the increase in aluminum recycling [2]. The BD should be dumped in controlled land field and it is costly procedure [4, 5].The water-soluble compounds in BD react with water or environmental humidity and release chlorides into the water and/or generate toxic gases such as H2, CH4, NH3 and H2 S [6-8]. In the Europe, BD is considered as toxic waste and its disposal as landfill is forbidden [8, 9]. After salt removal, the BD is considered to be non-hazardous and can be buried under ground [10].On the other hand, BD do also contains many relatively valuable compounds that may be changed in to useful materials as a result of further treatment [11, 12]"

Jan 1, 2012

By J. B. Vander Sande, I. G. Solórzano, B. S. You, P. M. Jardim, W. W. Park

"Alloys with six different compositions in the system Mg-Ca-Zn were produced by melt spinning. The aging behavior of alloys was investigated by measuring the changes in microhardness after isochronal aging and the microstructure was analyzed by means of transmission electron microscopy (TEM), energy dispersive X-ray spectrometry (EDS), scanning transmission electron microscopy (STEM) and scanning electron microscopy (SEM). All six compositions in the as-solidified condition show a difference in microstructure between the wheel contact side (zone A) and the free surface side (zone B) as a result of the differences in the solidification rate across the ribbons. One of the alloys (Mg-l.5wt%Ca-6wt%Zn) was chosen to be more deeply investigated in this work as it exhibited grain boundary films and an age hardening behavior was produced in that alloy.IntroductionMagnesium is the lightest of all the commonly used metals, and very attractive for applications in transportation. It also has a number of other desirable features, including good ductility, better damping characteristics than aluminum, and excellent castability. However, there are some negative features, such as high reactivity in the molten state, inferior fatigue and creep resistance as compared to aluminum, poor corrosion resistance and high production cost.In recent years there has been a significant increase in magnesium use as a structural material. These structural applications include aerospace, automotive and nuclear industries as well as appliances and sporting goods (1 ). According to reports on Mg-Zn alloys, the addition of Zn (2) in magnesium increased strength. Also, since the maximum solubility of Zn in magnesium is 6.2wt%, a considerable amount of Zn can be retained in solid solution in magnesium alloys by rapid solidification. In addition, Ca is known (3) to be one of the most potent alloying elements for refining the microstructure and precipitates in magnesium alloys, and also to improve mechanical strength and corrosion resistance."

Jan 1, 2000

By Baicheng Liu, Houfa Shen, Wensheng Li

"In order to understand the formation of macrosegregation in steel ingots, a mixture model has been developed which accounts for coupled mass, momentum, species, and energy transport to describe the sedimentation of free equiaxed grains during solidification. In this model, the mushy zone is divided into the slurry and porous regimes according to a solid packing fraction. Settling velocity of equiaxed grains in the slurry regime is given by an explicit expression. The solidification of a binary steel ingot (Fe-0.36wt.%C) with a two-dimensional geometry is numerically simulated. It is demonstrated that the predicted macrosegregation patterns agree to some extent with classical experimental results. Further refinement of this model is still necessary for realistically simulating steel ingot solidification.IntroductionModeling macrosegregation in steel ingots is still a challenging study, mainly due to the length scale of the products and the complexity of global multiphase transport phenomena coupled with microscopic solidification kinetics [l]. The thermal-solutal convection and the motion of equiaxed grains are the two main mechanisms responsible for macrosegregation. But there are few models that deal with the motion of equiaxed grains, which is confirmed as the main phenomenon that explains the negative macrosegregation along the centerline of large steel ingots [2]. A model which takes into account melt convection and grain sedimentation was first proposed by Beckermann and co-workers ([3], and references therein). More recently, similar multiphase solidification models with advanced nature have been presented by Wu and Ludwig [1,4] and Combeau and co-workers [5,6]. It is known that the application of these sophisticated models to steel ingot casting is at its beginning.In this paper, a solidification model based on continuum mixture approach, using much less sophisticated relations to obtain the settling velocity of free equiaxed grains, has been proposed in order to predict the macrosegregation in steel ingots. The model is applied to simulate the solidification of a binary steel ingot with a two-dimensional geometry, and preliminary modeling results are presented."

Jan 1, 2011

By Sijun Li, Bingyu Zhang, Haitao Zhou, Zhendong Zhang, Guofei Si, Xianghua Liu

"Hot compression test of Nb microalloyed coiled tubing steel is performed on Gleeble3500 at 1123K—1373K and strain rate from 0.001 to 5s-1. It is found that flow softening occurs and the flow curves exhibit a peak with a characteristic of dynamic recrystallization (DRX) and change with temperature and strain rate significantly. The peak stress and peak strain are dependent on the Zener-Hollomon relationship with activation energy of 390 KJ/mol. On the basis of Avrami equation and the Zener-Hollomon parameter, it is obtained that the dynamic recrystallization kinetics equation with which the calculated and measured recrystallization fraction is very close. On the results of hot compression test, the Nb microalloyed coiled tubing steel is rolled by Thermo-Mechanical-Control-Processing (TMCP), and it is obtained that the yield strength and tensile strength of Nb microalloyed coiled tubing steel are 565MPa and 685MPa respectively, and the elongation percentage is 30.1%.IntroductionCoiled tubing is widely used in oil field for well logging, well completion, drilling, work over and other operation in various fields to solve a number of conventional operating techniques problem which are difficult resolved, and it plays a more and more important part in exploration and production at oil field. [1] It will improve the efficiency of exploration and exploitation, studying, developing and using coiled tubing technology. Therefore, the development of domestic coiled tubing materials and manufacturing technology are great significance. It is well known that Coiled tubing has relatively poor working conditions and complex force state. So, the coiled tubing needs satisfier a kind of high strength, high plasticity, and corrosion resistant under complex oil gas condition. As the coiled tubing technology developed, the level of the coiled tubing steel is from CT55 originally to CT90 and CT100, and the corresponding tensile strength is 483MPa-758MPa. [2, 3]"

Jan 1, 2012