Search Documents

By C. J. McKee

A gold-silver-lead-zinc deposit at Montana Tunnels, Jefferson County, Montana is located in a diatreme of middle Eocene age (45 to 50 m.y.). Sulfide minerals within the diatreme occur as disseminations, veinlets, and locally as breccia matrix. Principal sulfide minerals are pyrite, sphalerite, and galena. The diatreme is a matrix-rich quartz latitic breccia with a fine grained rather soft matrix and heterolithic clasts. The ore deposit contains approximately 50 million tons of ore at a grade of 0.025 oz/ton Au, 0.5 oz/ton Ag, 0.25 % Pb, and 0.65 % Zn. Mining is by open pit methods. The original process flowsheet included flotation and cyanide leaching. Problems with the leaching circuit led to a change to the straight flotation process which is presently in use. To maintain a reason-ably uniform feed material, blending of ore is required for grades of four metals as well as for ore hardness and oxidation.

Jan 1, 1988

By Harold R. Kokal

Lisakovsky is a 3-billion ton oolitic iron ore deposit in north-central Kazakhstan operated by Orken LLP, a subsidiary of Ispat Karmet and the LNM Group. The iron oxide minerals are goethite and limonite. The gangue occurs as discrete quartz grains and an unidentified form of colloidal silica-alumina. The concentrate produced contains about 49.5 percent iron (Fe) and 0.6-0.8 percent phosphorus (P) or 10-20 times the acceptable phosphorus level. The phosphorus is intimately associated with the iron oxide and colloidal gangue, no discrete phosphorus minerals are found, and beneficiation is not possible. Therefore, to reduce the phosphorus, a hydrometallurgical process that includes roasting followed by leaching in dilute sulfuric acid has been developed. Phosphorus extraction is 70-90 percent, with only a minor loss of iron. The process has been tested in the laboratory and in a pilot plant at 50-300 kg/h. Construction of a 900,000 t/y demonstration plant is underway.

Jan 1, 2003

By Chai Liyuan

This paper focused on the preparation of porous ceramic pellets for microorganism carriers. A new method for the process was developed using simple gel-casting and bubble-in-water-in-oil type of multiphase double emulsion. The globules, consisting of a foamed sepiolite slurry suspension, were dispersed and consolidated in spherical shape in liquid paraffin as gelation progressed. The green pellets were sintered at 1100°C. The influence of surfactants, extension ratio and impeller revolution rate on the process and characteristics of the pellets was investigated. The pellet size was in the range of 1~4mm and determined directly by impeller revolution rate. The fine cell diameter of porous ceramic was in the range of 100~500m and the micropore diameter was less than 5m. The inner macropores were interconnected and extend to the external surface. It is impossible to analyze a result by SEM micrographs and digital camera.

Jan 1, 2006

By L. Y. Zhang

The current status of metal hydride alloys for NiMH batteries was systematically reviewed. Extensive application-oriented research and development has successfully made the NiMH battery an important part, with growing potential, among rechargeable batteries. The rare earth based metal hydrides (AB5) have been considered the best alloy material for use in the negative electrode in NiMH batteries. However, being in demand for high performance electronic markets, the still young NiMH industry is facing serious technical challenges in developing better products. Among all the efforts to respond to the challenges, advanced AF3, alloys are in great demand: the capacity enhancement race requires new or improved alloys possessing higher volumetric capacity; price competition mandates MH materials with low cost; high performance under severe service environments calls for alloys with high corrosion resistance when subjected to electrochemical cycling; and finally, high power service requires the negative electrode to deliver current at high rates.

Jan 1, 1997

By Vinod K. Namilakonda

In situ synthesis of discontinuously reinforced aluminum alloy metal matrix composites was investigated. Aluminum alloy (A356: Al-7 wt% Si) was reinforced with dispersed AlN particles. Thermodynamic calculations were made for the composition determination of various phases formed during bubbling of NH3 gas into the Al alloy melts in the temperature range 1173-1473 K. Experiments were carried out for in situ production of AlN particles with the reaction between Al melt and NH3 gas in high temperature resistance furnace at 1473 K. The products were characterized using SEM, EDS and XRD. Effect of bubbling time of NH3 gas on the AlN formed in the composites was studied. The amount of AlN reinforcement in the Al alloy composites was observed to be in the range of 5 to 35 wt%. Good agreement was observed between the experimental and thermodynamic calculated data on the composition of AlN in Al alloy composites.

Jan 1, 2006

By P. Klut, D. Groult, R. Marechalle, B. T. H. Bonnema

In the past 5 years, Compagnie Europeenne de Dezingage (CED) has developed a successful dezincing process and the St. Saulve pilot plant has evolved into a commercially successful production plant. Currently the plant meets all the required standards for scrap and zinc quality, output capacity, availability, and meets the prescribed environmental emissions standards. The initial process problems relating to zinc recovery, uncontrollable explosions and sodium hydroxide aerosol emissions have all been solved. Presntly, the yearly production of dezinced scrap is around 50.000 tonnes/year; this capacity is enough to supply the local market. This capacity can be increased easily to 65.000 tonnes/year or more. The market for dezinced material is growing due to the increased consumption of galvanized material on one hand and on the other hand the higher demand for high quality scrap. The proven technology of CED is currently patented worldwide, but CED is inviting licensees to implement the dezincing technology in other parts of the world.

Jan 1, 2000

By I. Sofia Fernandez del Rio

This paper describes a process for the treatment of the dusts generated during the operation of blast and reverberatory furnaces in the lead smelter, to remove zinc, cadmium, arsenic and halides from the circuit. The process consists of a Pefloles' developed leaching/purification stage and a solvent extraction process developed by Lurgi. The plant capacity is 5,000 tonnes Zn/year. The feed to solvent extraction contains 8 g/1 Zn. Impurities such as copper, iron, arsenic and cadmium are removed by conventional cementation processes. The cadmium product is 99.99 % pure. The solvent extraction process consists of two extraction stages, one washing stage and two stripping stages. D2EHPA is used as the extraction agent and 25% ammonia as the neutralizer. The rich-zinc solution is sent to the electrolytic zinc plant for zinc recovery. The raffinate produced, which is a mixture of ammonium sulfate and chloride, is used for agricultural applications.

Jan 1, 2000

By Qin Li

An highly active absorbent with oxidization based on fly ash, lime and additives was prepared. Experiments of simultaneous desulphurization and denitrification were carried out using fixture bed and duct injection. The influential factors for the absorptive capacity of the absorbent were studied. The absorptive capacities of 120.7mg for SO2 and 43.7 mg for NOx were achieved at a Ca/(S + N) molar ratio 1.2, respectively, corresponding removal efficiencies of 87% and 76%, while spent absorbent appeared in the form of dry powder. The optimal temperature and humidity of flue gas treated with this process were shown to be approximately 50\\176 and 5% respectively. The mechanism of removal for SO2 and NOx was investigated. In comparison with traditional dry FGD, this process appears to have lower cost, less complicated configuration and simpler disposal of used absorbent. The valuable references can be provided for industrial application by this process. The foreground of application will be vast in China and in the world.

Jan 1, 2006

By P. M. Rosário

The extraction performances exhibited by a phosphoric (D2EHPA), a phosphonic (Ionquest 801), a phosphinic (Cyanex 272) and a dithiophosphinic (Cyanex 301) acid derivative towards indium recovery from a diluted sulfuric solution are evaluated and compared. Equilibrium extraction isotherms were obtained. The chemical reactions involved and the approximate stoichiometry of the In(III) extracted species by the four ligands are presented and discussed. Stripping of In(III) from loaded D2EHPA and Ionquest 801 has been accomplished successfully, but has not been so effective from loaded Cyanex 301. Plots of %E vs. pH were established for D2EHPA, Ionquest 801 and Cyanex 301, denoting their behavior towards the extraction of similar mass concentrations of In(III), Fe(III), Fe(II) and Zn(II). Cyanex 301 is the least selective towards In(III), whereas D2EHPA and Ionquest 801, both for a pH = 0.5, do not extract Zn(II) at all.

Jan 1, 2003

By Pekka Parvinen, Saija Luukkanen, Pentti Pirkonen, Väinö Hintikka, Hannu Sekki

In the study was developed a new method for the treatment soils contaminated by polychlorinated dibenzodioxin and dibenzofuran. The method is based on attrition of soil so that the contaminants absorbed on the particle surfaces are liberated with the fine fraction formed in the attrition process. Same the attrition process produces active surface which can absorb the free contaminants. Before starting the remediation process must be decided the limit value under which the residual concentration must lie. Then in the laboratory is performed an experiment in the base of which is determined the grain size level; material under which much be removed together with the contaminant. In the real sample has been found that after the attrition the limit value 0.5 ng/g (I-TEQ) is obtained when the fine under 0.1mm fraction (20% of the original soils amount) is removed together with the contaminants 96% (original level 10 ng/g; 100%).

Jan 1, 2008

By Taner Kavas

In the present study the utilization of coal ashes that appear at the end of firing process of brick production in cement pastes was examined. Ashes with three different particle sizes of 75 µm, 106 µm and 150 µm were used to replace ordinary Portland cement (PC) as 5 % and 15 % by weight. Seven samples were prepared and physical, mechanical, chemical and microstructural analyses were carried out. The compressive and bending strength values of samples were determined at the ages of 2, 7 and 28 days. It was found that cementitious pastes with finer particle sizes possessed the highest compressive and bending strength values at all curing ages. Both values after 2 and 7 days cure increased with an increase in ash content, no matter what the particle sizes of ashes were. However, strength decreased after 28 days cure as a result of ash addition of 15 %, although it was still above that of the PC.

Jan 1, 2006

By Zachery Zanetell

Flotation circuit performance has become increasingly more challenging due to the complexity of available ore sources. To optimize value mineral recovery, the mineralogical composition of the ore should be evaluated and understood. Utilizing a variety of mineralogical and analytical tools, flotation processing challenges can be overcome and potential limitations understood. In this paper, several case studies will be discussed in terms of the value that has been provided through the use of mineralogical analysis to optimize flotation performance.

By R. A. Alock

The character, occurrence and genesis of the three types of nickel deposits, sulfide, laterite and deep-sea nodule are described, highlighting the differences in mineralogy and chemical composition that effect the extractive metallurgy of nickel and associated byproducts. World nickel production and current resources by deposit type and geographic location are also reviewed.

Jan 1, 1988

By Hongmin Zhu, Suning Liu, Kai Huang

"Recovery of silicon particles from the cutting slurry for the manufacturing of solar grade silicon is very important to recycle this kind of special resource. The challenge is to separate the silicon particles from the mixed abrasive particles which contain SiC. Various methods such as sedimentation, centrifugation, and flotation have been conducted, while in present work, a simple and effective novel method was proposed to study the separation of Si and coexisting SiC particles in the cutting slurry. The new process is based on the size difference between the two kinds of microparticles. And the membranes with the different pore sizes of 1µm, 2µm, 3µm and 5µm were used to test the pass ratio and separation efficiency of the suspension. Results shows that the effective separation of Si and SiC microparticles was obtained under the optimal conditions, and indicating great potential of practical enrichment of Si from the coexisting abrasive particles.IntroductionWith the development of the world economy, energy shortage and environment problem is becoming more and more seriously. Solar energy, which is regarded as one of the most important new energy in the word, has received much attention and interest from the scientists [1, 2]. More than 80% solar cells are manufactured by the high purity polysilicon as the raw material. The main process of producing silicon wafer is by multi-wire slicing. In this slice processing, large amount of slurry is produced. The slurry contains more than 30% wt silicon powder, silicon carbide powder as the abrasive, scraps of metal chips, as well as cutting abrasive suspension polyethylene glycol (PEG). The high-purified silicon powders are worth recycling and reusing as the materials for preparing solar-grade silicon though it is a big challenge [3].Most of the current studies were focusing on the recycling of the silicon carbide and PEG, while work on the recycling of the high-purified silicon is not so been focused since there is lacking of very effective separation and recovery technologies till up now. Nishijima utilized the method of superconducting magnetic to recycle the abrasive [4]. Wang applied a combinational process of chemical treatment, high-gravity centrifugation, high-temperature precipitation technique and directional solidification to enrich the silicon [5]. And other purification methods, such as centrifugation [6], froth flotation technologies [7], electrical filed separation [8] and phase-transfer process [9] have been employed. The disadvantages such as using poisonous media or complex equipments decrease the feasibility and efficiency of the above mentioned techniques."

Jan 1, 2014

By Hongmin Zhu, Qiuyu Wang, Shuqiang Jiao, Guojing Hu

"The equilibrium between titanium ions and metal titanium was investigated in fluoride-chloride molten salt. The electrochemical properties of titanium ions in fluoride-chloride were studied on a molybdenum electrode by cyclic voltammetry (CV) and square wave voltammetry (SWV). The equilibrium constant of the equilibrium between titanium ions and metal Ti was calculated in KCI-NaCl- 2.5wt %K2 Tif 6 at the temperature of 1073K.IntroductionTitanium, the ninth most abundant element in the earth's crust, is endowed with high strength, low density, excellent flexibility, strong spring back characteristics, high-temperature performance, corrosion resistance and biocompatibility. These characteristics make titanium eminently suitable to be used in aerospace, marine industries, and harsh chemical environments. Although it has many excellent properties, the application of titanium in industry was limited by its high-cost. Therefore, many methods have been investigated for producing high-purity titanium at low cost. Electrolysis, involving the extraction and preparation of pure metal from ore using an electrolytic process, is considered a promising method for titanium metallurgy. Many studies have focused on the electrochemical behaviour and electrodeposition of titanium in molten chloride, fluoride, and chloride-fluoride electrolytes (1-IOJ. The electroreduction mechanism of Ti3+ ions in molten alkali chlorides has previously been studied by several workers. Two reduction steps, Ti3+ -Ti2+ -Ti, have been observed in various molten alkali chlorides [IJ. One reduction step, Ti3+ -Ti, has been observed in alkali fluoride molten salts l21. The behaviour of Ti4+ in fluoride or chloride-fluoride molten salts has also been investigated in the literature; it was proposed that the reduction of Ti4+ ions in the molten salts proceeded in a two step process: Ti4+-Ti3+-Ti l3l or a three step process: Ti4+ -Ti3+ -Ti2+-Ti ri. 4l Indeed, the stability of the titanium oxidation states depends on the bath composition l5l. The valence state was Ti2+ in alkali chloride melts, which was a lower oxidation state and correspondingly, in alkali fluoride melts, the higher oxidation states ofTi4+ and Til+ were more stable.The aim of the present work is to explore the effect of F/Cl atomic ratio on the equilibrium between titanium ions and metal titanium in fluoride-chloride at the temperature of 1073K. The electrochemical properties of titanium ions in fluoride-chloride were studied on a molybdenum electrode by cyclic voltammetry (CV) and square wave voltammetry (SWV). The solubility product of the equilibrium between titanium ions and metal Ti was calculated."

Jan 1, 2012

By Ehsan Vahidi, Fereshteh Rashchi, Amirhossein Shahnazi

"The pig iron from steel manufacturing plants contains a high concentration of vanadium-bearing materials smelted with iron ore. During the oxidation process of the molten pig iron with oxygen lances, vanadium transfers to the slag. In this research, recovery of vanadium from LD (Linz-Donawitz) converter slag of steelmaking plant was investigated. The leaching residue was characterized by XRD and XRF techniques. The maximum vanadium recovery was achieved at optimum leaching conditions of 70 °C, S/L: 1/15, sodium hydroxide concentration: 3 M and leaching time: 150 minutes. The dissolution rate increased with rising sodium hydroxide concentration and temperature and decreasing particle size. The experimental data are treated graphically to explain the kinetics of the vanadium recovery process using shrinking core model (SCM). As a result, the controlling regimes in the SCM were analyzed separately using liquid film diffusion control, solid product diffusion control, and reaction control mechanisms.IntroductionVanadium is commercially important as a constituent of several alloys and catalysts. Nowadays, vanadium is mostly recovered as a by-product from secondary sources or from industrial waste streams such as titaniferrous magnetite, fly ash, spent catalysts, and petroleum coke. Steelmaking operations are specifically concerned by this problem due to the production of a huge quantity of by-products [1]. These by-products, including LD converter slag, sludge, fly ash, spent catalyst, ash, and alloyed scrap, contain a notable amount of heavy metals which may cause environmental problems. Solvent extraction is one of the techniques being increasingly used for the recovery of vanadium [2]. Apart from vanadium ore, secondary resources such as titanmagnetite, ilmenite and slag from the ferrous industry are a major source of supply. The pig iron from steel manufacturing contains a majority of vanadium-bearing materials smelted with iron ore. In a heat resistant shaking ladle the molten pig iron is oxidized with oxygen lances, causing the vanadium to be transferred to the slag. Normally, the vanadium in LD converter steel slag (coming from Linz-Donawitz steelmaking process) is ca. 5% as vanadium pentoxide (V2O5). This slag is the world's principal raw material for vanadium production [3, 4]. Moskalyk and Alfantazi [4] reported that a roast-leach process is used in South Africa for the production of vanadium oxides from magnetite ores while some of the slag was converted to ferrovanadium. A portion of the slag was exported to Europe for the production of vanadium oxide. The researchers mentioned that alkaline roasting was the main process at that time employed to extract vanadium pentoxide from vanadium slags."

Jan 1, 2012

By Yong Hwan, Wang Jian-Jun, Cai Jiu-Ju, Chen Chun-Xia

"The quantity of residual-heat and its recovery in some Chinese sinter plants are investigated. The main factors affecting energy consumption are analyzed using exergy analysis combining energy level analysis. It is indicated that the “gradation recovery and cascade utilize” of discharged gas and sinter residual heat in different temperature is the direction and the available approach to reduce energy consumption of the sinter process. Taking an iron& steel enterprise as an example, the three-ranked scheme of residual-heat recovery is put forward: ?Part of the sinter gas is used for warm-up and dryness; ?The high-temperature part of the cooler and exhaust-heat boiler are actualized as a closed-circuit, which can produce high-quality steam to generate electricity. ?The waste air in low-temperature part is introduced to sintering machine to support combustion. According to the CDQ which can recover the coal heat, the assumption of pot-recovery is put forward to replace the belt cooler. The two equipments of residual-heat recovery are analyzed in the aspect of energy consumption and CO2 reduction.1. IntroductionEnergy consumption in sintering is only inferior to iron-making in iron& steel enterprises, accounting for 10%~20% of the total energy consumption. A lot of residual heat is produced during sintering, and mostly from the sinter ore and waste gas. Sensible heat of hot sinter ore and discharged gas have accounted for 60%[1] (equals to 40 kgce/t-ore), which are the key point of sintering waste heat recovery. Discharge gas of sintering is mostly composed of flue gas deriving from sinter bed’s combustion, and the content distribution of H2O and O2 and the temperature of the gas along the length of belt-type sintering are shown in Figure1[2,3]. Currently, the sensible heat of hot sinter ore is mainly recovered by circular cooler and cooled by blasting air: the temperature of cooled discharge gas brings down from 350? to about 100? along with the decrease of sinter ore temperature. It is significant to recovery and reuse the waste heat as 4000~6000m3 discharge gas per ton of ore can be produced"

Jan 1, 2008

By R. T. Hernández, I. Hilerio, A. Altamirano, M. A. Barrón

"The principal objective for finishing surfaces is to protect and/or to decorate them. This can be achieved by adding or removing material from the work surface. The addition of aggregated material is called coating or recovering. In this work, mecano-chemical techniques are investigated for surface finishing. For these techniques, barreling or polishing by the friction method will be used. These are the cleaning or finishing processes most used for great volumes of small pieces. These methods improve the surface finishing by eliminating burrs, sharp pointed, tool marks and crusts of casting. They are used to clean metallic pieces, ceramics and polymeric materials. The process is based on rubbing or friction by abrasives. The pieces are arranged in the barrel with an abrasive and an additive (water or chemical additive). The machine produces a rotating movement on the pieces. When the abrasive passes against the surfaces of the pieces, it produces an action of rubbing and impact that cleans the surfaces. The rubbing action is developed when the upper layer of the charge slides to the lower extreme when the barrel rotates. The barrel can be hexagonal or octagonal to facilitate the sliding of the charge. The barrels can be between 15 to 120 cm in length and they can have almost any diameter and velocity of rotation. There are several types of barrel: individual, multiples, and multiple compartments. The barrels are rotated using a wheel spindle or rolling pins, that the can ride horizontally or be tilted to produce an additional movement of the charge.IntroductionShot penning is a cold method in which compressive effects are induced on an exposed surface of a metallic piece, by the impact of a rain of shots directly on the surface of the metal, at great speed under controlled conditions. This differs from cleaning with the help of air, because even when shot penning cleans the surface of the metal, this function is incidental. The main purpose of shot penning is to increase the resistance of the piece to fatigue. The process has other applications: raises the tensile strength and decrease corrosion fracture."

Jan 1, 2012

By Anurag Tripathi, J. K. Saha, S. K. Ajmani, J. B. Singh

"The quality of steel is a major concern in the metallurgical industry. The control of liquid steel temperature can enhance the level of cleanliness in steel. Ladle is one of the major vessels used to transfer liquid steel between different stations. The heat transfer phenomenon taking place in this vessel needs to be monitored for controlling the liquid steel temperature. A CFD model was developed for prediction of liquid steel temperature during complete process cycle of ladles in direct heats. The model was validated with liquid steel temperature measured at on-line purging station and tundish during teeming from one of the actual steel plant. The accuracy of model was 96 %. The results obtained show insignificant effect of slag thickness, tapping temperature and ladle life on liquid steel temperature in the ladle. However, the importance of initial refractory temperature was noticed. The CFD model developed in present work can generate the thermal history of liquid steel and refractory walls of any ladle at any stage.1. IntroductionThe control of liquid steel temperature is desired to achieve required steel quality. The low casting temperature is detrimental and may result in nozzle blockages due to premature solidification in the tundish. The phenomenon of heat losses taking place in ladles needs to be understood for prediction of liquid steel temperature. The assessment of thermal profile of liquid steel from BOF converter to caster can be done through consideration of heat losses at all points. Hlinka and Miller [1] showed that the ladle pouring temperature varies due to heat losses from molten steel into surrounding refractory layers. The phenomenon of thermal stratification was numerically simulated by Ilegbusi and Szekeley [2]. The effects of slag cover on heat loss and liquid steel flow in ladle before and during teeming to a continuous casting tundish was numerically simulated by Chakraborty and Sahai [3]. Investigators also developed some simple models to predict the steel temperature for some of the processes taking place in ladles [4-9].The present work is an effort to generate the full information about the temperature drop taking place in any ladle throughout its process cycle. This information can be used to predict liquid steel temperature and to take decisions to minimize heat losses."

Jan 1, 2012

By Toshiyuki Nohira, Eiichi Takeuchi, Tetsuo Oishi, Hideki Ono, Hirokazu Konishi

The Dy-Nd-Pr-Ni alloy sample was prepared by cathodic potentiostatic electrolysis at 0.65 V (vs. Li+/Li) for 1 h using a Ni plate in a molten LiCl-KCl-DyCl3-NdCl3-PrCl3 system at 723 K. The highest mass ratio (Dy/Nd+Pr) in the alloy sample was observed to be 50 at 0.65 V. Anodic potentiostatic electrolysis at 2.20 V for 12 h was conducted using the Nd-Fe-B magnet electrode in a molten LiCl-KCl system. All elements were almost dissolved from the magnet, and the original form of the magnet disintegrated. After anodic potentiostatic electrolysis at 2.20 V, cathodic potentiostatic electrolysis was conducted at 1.00 V for 5 h using a Mo plate in order to remove the dissolved Fe from the bath. Finally, cathodic potentiostatic electrolysis was conducted at 0.65 V for 12 h using a Ni plate. The mass ratio of Dy/Nd in the alloy sample was determined to be about 18.

Jan 1, 2015