Search Documents

By S. Moussa

The formation of boron-doped nickel aluminides Ni3AI, (76 at. % Ni) from elemental powders by reaction synthesis using reactive sintering was studied. The process involves the mixing of elemental powders of nickel and aluminium with various wt % of boron up to 1 wt % boron. Nickel and Aluminium powders were mixed in the correct proportion to form the intended boron-doped nickel aluminide intermetallic. XRD, SEMI EDS, Image analysis and Archimedes principle; were used to study the effect of Boron addition on the final microstructure, bulk density, average grain size of as reactively-sintered nickel aluminides (boron-doped), compared with no boron addition. The results showed that at greater boron content than 0.3 wt %, a two-phase non-equilibrium microstructure of consisting of NiAI phase in NiJAI matrix was formed that have been primarily retained even after heat treatment for 5 hours at 1000 °C. Boron was present in solid-solution within both the NiAI and the Ni3AI (in greater amounts) phases.

Jan 1, 2001

By K. Gao, R. Dry

"Carbon boil, which results in excessive spitting and even complete destruction of a metal drop, could significantly influence the efficiency of direct smelting processes. Carbon boil has been studied as a function of some key parameters such as melt sulfur content, oxygen partial pressure, and melt area/volume ratio. The time of carbon boil was determined using a CCO camera coupled with a time/date generator connected in parallel to a video recorder and a computer. The time of carbon boil was in the range ~5 - 15 seconds under the conditions in this study. A mechanism for carbon boil has been proposed.IntroductionThe occurrence of carbon boil in molten iron drops can result in excessive spitting and sometimes even complete destruction of a metal drop. In direct iron smelting processes, this could significantly influence the decarburisation of liquid metal and the post combustion and hence may influence the efficiency of smelting processes. The generation and consequent ejection of metal droplets into the gas phase occurs due to the intense turbulence in the bath which results from the injection of gases and coal. The aim of this investigation is to understand the fundamentals governing the carbon boil phenomenon under direct iron smelting conditions to assist control of process efficiency.Carbon boil phenomenon has been studied as a function of some key parameters such as melt sulfur content, oxygen partial pressure and melt area/volume ratio. The time for the occurrence of carbon boil has been determined in this study at 1440 °C using a novel approach which includes utilisation of a CCD camera coupled with a time/date generator connected in parallel to a video recorder and a computer. This arrangement permits the capture of the entire sequence of events leading up to carbon boil and therefore the determination of time of boil which is in the range -5 - 15 seconds under the conditions in this study."

Jan 1, 1996

By Chao Lian, Hongxu Li, Hao Bai, Wei Wei

"Application of high-emissivity coating on inner walls in industrial furnaces increases the furnace thermal efficiency. The coating with high emissivity strengthens radiation heat transfer in the furnace, however, according to Wien's displacement law and Planck's radiation law, under heating temperature, the wavelengths of the radiation transfer are mostly between 1-5 µm, implying that increasing emissivity of the coating in near infrared band is more effective for higher thermal efficiency. In this paper, a new CuO-ZnO-based coating material sintered at 1600K was developed. The emissivity of the samples were measured and the result shows that, in near-infrared band, the emissivity of the sample reaches 0.98 at 773K with 13at.% of CuO doped in ZnO. In addition, the effects of CuO doping and use temperature on emissivity were also discussed. Furthermore, crystallization behaviors of ZnO-CuO sintering were investigated by DTA,XRD and SEM-EDS etc., which offered information for possible optimal design of the material.1. IntroductionIndustrial furnaces are widely used in various industrial heating. For example, the metal smelting furnace, ore sintering furnace in metallurgical industry; the distillation furnace, cracking furnace in petroleum industry etc,. The research on efficient energy saving technology has important significance. High emissivity coatings are widely used in many high temperature applications to effectively transfer the heat by radiation [ 1]. The theoretical calculation and experimental studies have shown that, coated high emissivity coating in the heating surface is an effective method to enlarge the infrared radiation power [2].At present, the infrared high emissivity coating has been widely used in China, and have been achieved remarkable energy saving effect. According to Wien' s displacement law and Planck' slaw, most energy of the black body at high temperature is radiated in the wavelength range of l-5µm; however it happens that many materials have the low emissivity within this range. Thus, it is important to improve the near-infrared band emissivity of materials [3]."

Jan 1, 2013

By Sang-Joon Kim, Hae-Geon Lee, Hyun-Jin Cho

"Decarburization phenomena on the surface of liquid iron have been simulated by numerical method and the results were compared to the experimental data. During the DeC process in a converter, a large amount of splashed droplets are generated from the top surface of the bath and consequently the reaction surface area is increasing tremendously. Since the decarburization mainly occurs at the interface, it is important to understand the reactions on the liquid iron droplets. The flow and species concentration fields around liquid droplets taking into account the reaction of carbon with oxygen at the interface were calculated by a commercial CFD code FLUENT which solving multiphase Navier-Stokes equation with Volume Of Fluid method, species transport equations and energy transport equation. The initial carbon concentration was fixed to 4 wt% and the concentrations of oxygen in the atmosphere were varied from 5 to 50 wt%. As comparing the numerical calculation with experimental data written in the reference, the results have a good agreement for decarburization rate.IntroductionIn a primary steelmaking process, one of the main functions is to decarburize from hot metal and the 4% of carbon is decreased to about 0.5% of carbon. Even though there are some possible reactions leading to the removal of carbon from hot metal, the main reaction occurs on the free surface by direct oxidation of carbon at the gas-liquid interface with producing the carbon monoxide gas. In many metallurgical processes involving a jet impinging onto a steel bath surface, especially in a Basic Oxygen Furnace (BOF) converter, it is important to understand the behavior of molten iron droplets splashing out of the steel. The iron droplets are generated by an oxygen or air jet blowing and it increases the total surface area of liquid iron tremendously. Since the decarburization reaction is mainly affected by the surface area, it is necessary to verify the decarburization phenomena around the splashed droplets from liquid iron in order to allow an analysis ofBOF process possible."

Jan 1, 2011

By Zhang Libo, Wang Xin, Peng Jin-hui, Ju Shaohua, Guo Sheng-hui, Xu Lei, Huang Meng-yang

"China is lacking high grade titanium ores. This work intends to leach impurities such as Fe, Ca and Mg from a low grade titanium ore, to increase the grade. The original material contained 65% TiO2 , 16.12% Fe, 9.4% CaO + MgO, 4.2% SiO2, 1.25% A12O3, and the particle size is between 0.053-0.045mm. Microwave energy was used to enhance the leaching effect. The results showed that when normal heating was used to leach the mineral, the extraction of impurities Fe, Ca and Mg was very low. However, when microwave energy is introduced, the extraction of Fe, Ca and Mg increased dramatically. The optimized conditions are: relative power 5W/g, the ratio of concentrate to HC1 isl5%, leaching at 160°C for 20 min with a ratio of liquid to solid 12:1 mL/g. The material obtained under these conditions contains 92.73% TiO2, 0.207% Ca + Mg, 0.8% Fe, with 94.6% Ti recovery. The poduct meets with the quality for boiling chlorine.IntroductionThe resources of titanium are very abundant, and are distributed all over the world. There are almost 140 minerals containing TiO2 with a content of more than 1%. However, there are only several minerals which can be used for producing sponge titanium. They are mainly rutile and ilmenite. The grade of nature rutile concentrates is higher than 95% TiO2, and it is a high quality raw material. But the resources of nature rutile are relatively low; after mining for many years, its resources are exhausting gradually. Although ilmenite reserves are great, ilmenite cannot be used as a raw material because of its low content of TiO2, only 45-70%; also it has a high impurity content of Ca, Mg and Fe. In these years, there is a tendency for titanium industry to use high grade concentrate."

Jan 1, 2012

By C. A. Nogueira, F. Pedrosa, F. Margarido, R. N. G. Guerra

"A hydrometallurgical process for recycling spent Zn-MnO2 batteries was developed, involving leaching with sulfuric acid, purification by precipitation and metals separation for further recovery. Leaching of zinc oxide was easily attained while for manganese oxide was rather difficult depending on temperature and acid concentration. At 90°C and with the liquid/solid ratio of 20 L/kg, more than 95% of zinc is recovered in 30 minutes with 0.5M H2SO4. To attain similar recovery for manganese, higher levels of acid concentration and time are needed (e.g 0.7 M and 2 hours). After leaching a purification step is necessary to remove iron co-dissolved through Fe(III) precipitation. Separation of zinc from manganese by solvent extraction with 1M DEHPA follows in the process route. The countercurrent multistage separation diagram developed allows the production of a zinc electrolyte with 120 g/L Zn and 0.005 g/L Mn, and a raffinate with 16 g/L Mn and 0.013 g/L Zn.IntroductionThe recycling of spent Zn-MnO2 batteries is carried out by dedicated recyclers using several process alternatives [1]. Most of the running processes use pyrometallurgical technologies [2] based on zinc distillation. Alternative treatments by hydrometallurgy have been reported [3-5] but its application is scarce.In order to contribute to the development of alternative solutions, a process for recycling batteries based on Zn-MnO2 systems has been studied. The process is based on the hydrometallurgical treatment of spent batteries in sulfuric acid media (Figure 1). The process starts with the physical processing by shredding using cutting grinders, where the batteries are opened and size reduced, allowing the liberation of the interior electrode particles or pastes. The fines can be then separated and the coarse material containing the steel scrap can be treated to remove the remaining aggregate electrode. The final scrap also contains some plastics and other non-metal materials and can be further valorized."

Jan 1, 2008

By Somayeh Dashti, Ehsan Vahidi, Fereshteh Rashchi

"The main goals in zinc electrowinning process are decreasing of power consumption and increasing of current efficiency. In this study, the electrowinning of zinc in the presence of different additives in electrolyte were established and Arabic Gum, Gelatine, sodium lauryl sulphate and l-hexyl-3-methylimidazolium hydrogen sulfate in the five levels using Taguchi method was examined. In our previous researches, using orthogonal array, effect of zinc electrowinning parameters such as anode type, current density, sulphuric acid concentration, temperature and zinc ion concentration was studied and the optimized conditions for zinc electrowinning was obtained. Anode composition: Pb-Ag 0.5%-Sn2%-Sb1%, current density (A/m2):500, acid concentration (g/1):165, temperature: 60°C, zinc ion concentration (g/1):70. The main goals in zinc electrowinning process are decreasing of power consumption and increasing of current efficiency. ln this research, the effect of four additives: Gum Arabic, Gelatine, sodium lauryl sulphate and an organic material in the four levels with Taguchi method was examined. ln fact the effect of electrolyte environment and determining the best electrolyte under the optimized conditions is the main aim of this study.IntroductionDue to its low cost and abundance, zinc is widely used in the production of brass, galvanized steel, sacrificed anodes and primary and secondary batteries [I]. Some 80% of world primary zinc production is derived via roast-leach-electrowinning processes [2-4]. In the electrowinning process to both improve final product quality and current efficiency the leachate should be purified [5].To produce zinc a current method is to extractit from acidic zinc sulphate solutions by electrolysis with aluminum cathodes and insoluble lead-based anodes [6]. Though the electrolytic processing of zinc has been performed for many years, there are still current efficiency problems in the cathodic process. These low efficiencies (88- 93%) have a serious impact on the costs associated with the energy consumption. On the other hand, these low efficiencies increase energy consumption and decrease the quality of the surface morphology [7- 8]."

Jan 1, 2012

By Heinz Boeni, Daniel Ott, Uca Silva

"Latin America is facing a rapid increase in internet use. Penetration with electronic equipment is in some countries approaching the level of industrialized countries. There is an evident need to resolve the management of “end-of-life” computers and other electronic equipment. Several studies in Latin America assessed the increasing e-waste quantities and confirmed the importance of a sustainable e-waste management. This paper gives an overview on the status on e-waste management in Latin America, explains the challenges for establishing an e-waste management system in a developing country setting and highlights the social and economic potential and the possibilities of a regional approach.IntroductionGlobal ICT-Trade and generation of e-waste from ICTThe global production of electronic devices and particularly of Information and Communication Technologies (ICT) faces the biggest industrial expansion of the history: OECD figures show that global trade of ICT technologies has reached 7.7% of the gross world product by 2004, the major proportion accruing from China [1]. In 2006 an estimated 230 million computers and 1 billion cell phones have been sold worldwide which corresponds to a volume of 5’848’000 t [2]. As a consequence, Waste from Electrical and Electronic Equipment (WEEE), or e-waste, is by far the fastest growing waste component. It reaches more than 5% referred to Municipal Solid Waste and e-waste generation in developing countries according to UNEP is expected to triple by 2010 [2].According to the OECD e-waste is “any appliance using an electric power supply that has reached its end-of-life” [3]. The European WEEE directive [4] distinguishes 10 categories of ewaste: Big household appliances, Small Household Appliances, IT and Telecommunications Equipment, Consumer Equipment, Lighting Equipment, Electrical and Electronic Tools, Toys, Leisure and Sports Equipment, Medical devices, Monitoring and Control Instruments, and Automatic dispensers. In this paper e-waste and WEEE are used as synonyms. Focus will be laid on e-waste from IT equipment (IT-waste), corresponding to category 3 of the European WEEEDirective."

Jan 1, 2008

By Alejandro R. Alonso, Lizet Alvarado, Gretchen T. Lapidus

"Cobalt and lithium recovery from spent Li-ion secondary batteries has been increasingly studied in recent years due to the high value of both metals and the low proven reserves for lithium. The standard method employed until now has been the deactivation and crushing of the batteries, followed by leaching of the L1C0O2 spinel from the battery cathode using acid solutions, such as 1.5 to 2.0 M HC1 or H2SO4, in a temperature range from 120°C to 250°C. Once leached, the cobalt is separated by electrodeposition and the lithium by precipitation, using large amounts of carbonate to bring the solution to alkaline pH values. In the present work, citric-thiosulfate solutions are used for the spinel leach at room temperature, favoring a reductive environment at room temperature, which stabilizes the cobalt(II) as cobalt citrate and lithium(I) at pH 5, and recovers approximately 99% of both metals.IntroductionThe Li-ion batteries industry has become an important economic sector in recent years. This type of battery is the most promising system for energy storage, because of its high efficiency in charge-discharge cycles, and its adaptability to many configurations. The demand will probably increase because of the need for mobile energy sources in many types of devices ranging from cell phones, tablets, and laptops to medical, navigation and sophisticated communication equipment and even in automobiles.One major problem related to the use of these batteries is the method employed for recycling the components, mostly cobalt and lithium. Currently, there are two processes employed on an industrial scale: the Sony/Sumimoto process, used since 1990 [1] and the Toxco Process [2]. In the first case, incineration is used to open the batteries and at same time volatilize the organic solvents. After that, the metals (copper, iron and aluminum) are physically separated. The cobalt and lithium are recovered as oxides and then thermally treated in order to recycle them for new batteries manufacture."

Jan 1, 2012

By R. G. Reddy

The effect of solid particles on viscosity behavior of Na2O-O-B2O3-SiO2 melts of composition XSio2/XNa2o =0.5 and in the temperature range of 900- 1150 K was studied. Samples were analyzed by X-ray diffraction and optical microscopy. The results showed that a crystalline phase (NaBO2) was formed and its amount increases with decrease in X,, from 0.50 to 0.25. The experimental viscosity values were compared with the predicted values using our viscosity model developed earlier. At low temperatures, for low content of B2O3 , the experimental values exhibits a large deviation from the predicted values. It was concluded that the deviation was due to the formation of solid particles in the molten slags. The existence of these solid particles increased the viscosity values significantly. A new viscosity model was developed to include the effect of solid particles.

Jan 1, 1993

By Vladimir Lobanov, Vladimir Skorohodov, Andrew Evdokimov, Ural State Technical University 19, Boris Radionov

"The bulk of raw materials in metallurgy of secondary platinum metals are the wastes such as multilayered ceramic-metal systems, e.g. the spent catalysts of the chemical and petrochemical industry, automobile catalysts, etc. Due high chemical resistance of a ceramic basis the extraction of platinum metals by leaching even at very fine crushing is poor. The study of sorption leaching of platinum and a palladium from the spent automobile catalysts are carried out. The average content of PGM is 0.5%. A few methods of raw materials sampling were compared: 1) direct hydrometallurgical leaching of platinum metals from the fine-grained catalyst and atomic absorption analysis of the obtained solutions; 2) fusion to a metal or sulphidic collector of precious metals with the alloy analysis by direct spectrometry; 3) fusion with dissolution of a precious metals collector and atomic absorption analysis of PGM in solutions. Leaching allows detecting out no more than 90% of a palladium and 80% of platinum. Fusion to a collector gives the best results at the chemical ending. Researches on sorption leaching are executed. Under optimum conditions the extraction of platinum metals to concentrates is comparable with similar indicators of collector fusion.The large part of raw materials in metallurgy of secondary platinum metals are the multilayered or tridimensional ceramic-metal systems, in particular the spent catalysts of the chemical and petrochemical industry, automobile catalysts, ceramic-metal condensers, etc. The content of the sum of PGMs can be from hundreds grams per ton to several percent. For processing of such materials the hydrometallurgical methods of platinum metals leaching by various reagents are used commonly. High chemical resistance of the ceramic basis covering the metal particles causes low recovery even at very fine grinding. Other fundamentally different method of catalysts opening includes dissolution of the ceramic basis in the solutions of hydrofluoric acid and the subsequent recovery of platinum metals from insoluble residue. Application of this method is associated to use of corrosive medias and appropriate equipment. Fusion of the specified materials with collecting of PGM by copper, nickel or lead at the specialized enterprises provides higher extraction in semiproduct. At the same time, complexity and duration of the subsequent extraction of platinum metals concentrates causes high total cost per unit. Thereby this method is economically acceptable only for rather poor raw materials (no more than 0,1%). Undoubtedly, that the raw materials with the high content of PGM are reasonable to process by individual technology. In the present work the processing of some kinds of ceramic-metal raw materials, particularly automobile catalysts (neutralizers) with various collectors at the conditions of a target fusion are investigated."

Jan 1, 2008

By Gaifeng Xue, Xiaohong Xu, Meng Liu, Yijie Song, Guotao Xu, Jixiong Liu

BN (Boron Nitride) based composites were prepared with hot-pressing by using h-BN as main material in ceramic preparation process. The relative density, bending strength, vickers’ hardness, thermal shock resistance, thermal expansion coefficient, thermal conductivity, phase composition and microstructure were tested and analyzed by using modern testing technology. The results indicate that the best formula is B, the relative density is 97%, the bending strength is 260 MPa, the hardness is HV5 343kg/mm2, the thermal expansion coefficient is 2.8×10-6℃-1, the thermal conductivity is 22 W/(m.K) and have no crack after thermal shock for 20 times by water cool. XRD analysis indicates that the main phase compositions are h-BN, β-Si3N4 and sialon. SEM studies show that the grains wrapped up by solid solution.

Jan 1, 2015

By Tom McCullough

The purpose of this paper is to discuss the implementation and results derived from installing oxy-fuel burners in a l80 ton copper reverbatory melting furnace. Specific results will be discussed in the areas of melt chemistry, furnace modifications, productivity, process enhancements, and the combustion system capabilities.

Jan 1, 1996

By Y. H. Su, C. Y. A. Tsao

"The solidification behaviors and velocity of atomized droplets during flight is formulated by a mathematical model, in which the concept of transient nucleation is applied. During the flight, the droplet velocity shows a maximum, followed by an inflection phenomenon. The velocity of large droplet is lower than that of small droplet at shorter flight distance, and higher than that of small droplet at longer flight distance. The effect of the gas flow pattern is more significant at longer flight distance than at shorter flight distance at a given flight distance, large droplet has higher temperature than small droplets prior to nucleation. Large droplet has higher nucleation temperature than small droplet. Medium size droplet flies over the shortest flight distance before the nucleation starts. At the end of recalescence, large droplet has less solid fraction than small droplet has.IntroductionTraditional concept of steady state nucleation was used in all the previous models describing the solidification of molten droplets. [1-5] However, during atomization, the solidification rate of the molten metal droplets is very high, and therefore there is very little time for the nucleation event to occur. In the present work, the concept of transient nucleation [6] is considered to model such short nucleation event during solidification of the atomized droplets. The solidification behaviors and velocity of atomized droplets are modeled and the effects of the atomization gas flow pattern are also presented."

Jan 1, 1997

By Toshihiro Kuzuya

A hydro metallurgical process has been developed for the recovery of metal values such as Co, Ni and rare earths from the electrode materials of spent nickel metal-hydride(Ni-MH) secondary battery. MmNis_xCo. (Mm : Misch metal) intermetallic compound could be separated from the electrode materials mixture by sedimentation. A typical chemical composition of MmN5-xCox was approximately, in mass%, 56.0%Ni, 13.4%Ce, 10.6%La and 7.9%Co. The time dependency of leaching intermetallic compound with sulfuric acid solution was examined with processing factors such as sulfuric acid concentration, temperature and agitation intensity, The leaching of rare earth metals proceeded very rapidly, reaching completion in less than 1.8ks. On the other hand, the slow leaching of nickel was observed. The percent of nickel leached at 328K could only reach about 70%.

Jan 1, 2003

By Markus A. Reuter, Antoinette van Schaik

"Product design engineers select from a wide range of materials and combine them into multimaterial product designs. These include various materials (metals and non-metals) which are complexly integrated (e.g. welded, glued, alloyed, layered). The recycling/recovery rate of consumer products are determined by the different materials and alloys used, but also by the particle size and multi-material particle composition after shredding (combination of materials due to design). Eco-design (for recycling) and Design for Recycling (DfR) can only be conducted if the interconnectivity of material/metal in various unliberated materials is accounted for and its effect on material and energy recovery can be linked back to design. This paper will discuss the basic principles of these DfR models and it is shown how these tools (i) are linked Computer Aided Design (CAD) and Life Cycle Assessment (LCA) software, (ii) affect conceptual design specifications of products, (iii) integrate the complex detail of the recycling system and recyclate quality and hence (iv) make recycling an integrated part of the product system. Furthermore, it is shown how these assessment tools and models can be applied for benchmarking of the recyclability and environmental damage created by the recycling of end-oflife consumer goods in order to e.g. (i) provide the (original) equipment manufacturer with knowledge and solutions to support product stewardship and Extended Producer Responsibility; (ii) create awareness of the consequences/benefits of design, products and recycling systems to manufacturer, designer, legislator, recycler etc.; and (iii) assist the consumer in their choice of consumer goods from an end-of-life point of view.IntroductionA first-principles basis is required in order to be able to simulate and predict the recycling/recovery behaviour of products facilitating Design for Recycling (DfR) and Eco- Design. This links recycling technology and the environmental consequences of recycling directly to product design."

Jan 1, 2008

By Rauno Peippo

Horizontal Waste Heat Boiler (WHB), today's proven and dominating technology for copper smelter gas cooling, has been utilized by the industry for over half a century. During this time development has taken place in geometry, flow characteristics, cleaning technology and design details. This development has been driven by improved understanding of the specific process requirements, gained both by wide experience and by utilizing new emerging design tools, like computer flow modeling. It had to wait till mid 90's to unite effective and proven Spring Hammer cleaning technology and the process benefits gained by gas guiding vanes or baffle wall in the copper smelter WHB design. The new design has demonstrated improvement in gas cooling efficiency and the process conditions down stream in form of less dust sticking problems in the boiler and precipitators. Reduced weak acid production has also been reported as a result of the design. The theoretical aspects, computer flow modeling results and actual benefits measured in old smelting line modernization are discussed. Experience £tom modernization projects such as Phelps Dodge, Atlantic Copper, Mexicana de Cobre, and Nippon Mining, Saganoseki, are discussed. In mechanical design there has been development resulting improved gas tightness with less corrosion and better control of dust sulfation. An essential improvement is the integration of the boiler hopper and dust removing conveyor. Having no steel plate casings in the hopper and conveyor section but using of boiler tube membrane instead eliminates thermal expansion differences. The dust conveyor will be effectively cooled against hot dust lumps falling down while the acid dew point corrosion is prevented in the cooler sections of the hopper. Conceptual features are presented of a new generation Copper Flash Smelter WHB presently under construction at Boliden Mineral, Skelleftehamn, Sweden, where the latest development and innovations are adopted.

Jan 1, 1999

By Jie Li, Thomas A. Rawdanowicz, W. J. Collis, S. Venkatraman, S. Iyer

"InSb being the lowest band gap. material amongst the 111-V semiconductors with low effective mass has long attracted research interest, due to its potential application in far infrared devices and for high speed circuit elements. In this paper, we report, for the first time, Te-doping of InSb on GaAs substrate using SnTe doping source with molecular beam epitaxy (MBE) technique and its electrical characterization. The undoped epilayers are n-type in the temperature range of 10 K to 300 K investigated. The room temperature (RT) mobility as high as 64,810 cm2/V·s (1.9x1016 cm-3) have been measured on a 4.8 µm thick epilayer. Sn Te doping at different doping levels were investigated. 5. 7 µm thick doped layers with RT carrier concentrations ranging from 2x1016 cm-3 to 3.2x1018 cm-3 with corresponding full width at half maximum (FWHM) of x-ray (400) rocking curve varying from 170-200 arc-seconds have been achieved. The Hall mobility of 20,000 cm2/V·s at 1.3xl018 cm-3 carrier concentration was obtained indicating that SnTe is a good candidate as source material for n-type doping of InSb.IntroductionThe thin films of InSb and InSb-based alloys have found considerable interest because of potential applications in III-V semiconductor-based infrared optoelectronic devices1• In addition, the advantage of the small effective mass and the consequent high mobility can be utilized in high frequency and high-speed circuit devices2 InSb can also be used in magnetoresistive sensors for position sensing3. Epitaxial InSb films grown by MBE may be doped n-type with Si or Sn, or with the group VI elements, namely, S, Se, or Te. Of the group VI elements, Te may be advantageous because of its relatively low vapor pressure. However, the vapor pressure is high enough to have sufficient memory effect during MBE growth. Hence different telluride compounds such as GaTe45, PbTe6 and Sb2Te37 have been used as the dopant source for Sb-based compounds. SnTe has also been used as a successful n-type dopant in the MBE growth ofGaSb8 But, to our knowledge, there is no report on the investigation of SnTe doping of InSb. In this paper, we report the first doping characteristics of SnTe in InSb layers grown on GaAs substrate."

Jan 1, 1998

By Nobuaki Sato

The electrical conductivity, k, of pure and sodium doped sulfur melts was measured with and without ultrasonic waves at temperatures ranging from 140 to 340° C by the two probe method using an ultra high resistance meter. The II: value of the pure sulfur melt with irradiation jumped at around 170°C by an order of 102 after which it monotonically increased from 10-5 to 10-4 (omega) 1cm-4 with an increase of the temperature. The addition of the sodium metal to the sulfur melt was found to cause a larger jumping in the II: value. The II: value increased with the increase of Na proportion in the melt. For a 10 mol% Na doped sulfur melt it was as high as max. ~30 (omega) 1cm-1 above 180°C under the irradiation of ultrasonics.

Jan 1, 2003

By Maribel L- Saucedo-Muñoz, Toshiyuki Hashida, Victor M. Lopez-Hirata, Shin-Ichi Komazaki

"Small-punch tests were conducted at 4, 77 and 293 K on three types of austenitic stainless steels JNl, JJl and JK2, which were solution treated, water-quenched and then aged at 923, 973, 1023 and 1073 K for 5 h. Small-punch test energy was employed for the evaluation of the aginginduced embrittlement behavior in these materials. Fracture surface of small punch test specimen for the solution treated steels exhibited a ductile fracture, showing the highest SP test energy values. The presence of intergranular brittle fracture was observed in aged specimens. Smallpunch test energy decreased significantly as the aging process progressed. The highest and lowest decrease in small-punch test energy with aging temperature occurred in JNl and JK2 steels, respectively. The decrease in small-punch test energy showed to examine appropriately the aging-induced embrittlement in these materials. The difference in aging-induced embrittlement behavior for these steels was explained based on the volume fraction of intergranular precipitates in aged samples.IntroductionA high level combination of strength and toughness is required for cryogenic structural materials used in the superconducting magnets of fusion nuclear reactor. This requirement is beyond the capability of conventional austenitic stainless steels [1]. The Japan Atomic Energy Research Institute (JAERI) developed new cryogenic JNl, JJl and JK2 austenitic stainless steels. The structure of superconducting magnets is supposed to be constructed by welding thick plates of this kind of steels. Thus, most of the components are exposed to thermal cycles. The slow cooling may cause microstructure changes in both the base material and weld zone. These changes may also decrease the fracture toughness of these materials at cryogenic temperatures. Therefore, it is important to study the effect of thermal aging on fracture toughness behavior for these steels. Konosu et al. [2] carried out a study of the effect of thermal aging on the mechanical properties for JNl steel using tension and fatigue tests. Kwon et al. [3] evaluated the deterioration in fracture toughness at cryogenic temperatures for the isothermally aged JNl steel by means of the Small-Punch (SP) test. No other reports were found about the cryogenic fracture toughness behavior for this kind of steels. To evaluate the cryogenic fracture behavior, the elastic-plastic Jrc value is a good alternative [4,5]; nevertheless, the standard required specimen size makes it difficult to be used for the fracture toughness evaluation in small zones."

Jan 1, 2011