Search Documents

By A. V. Tarasov

In order to improve technical, economic and environmental performance of hydrometallurgical processing of intermediate products containing copper and nickel, the Gintsvetmet Institute and the IMET Institute of the Russian Academy of Sciences have conducted studies into the efficiency of the use of alternating current of industrial frequency on processes applied for hydrochemical leaching of various copper- and nickel-containing materials. It has been found that: 1.Imposition of alternating current over the process of leaching of softly reduced nickel oxide with recycled copper sulfate solutions resulted in an increase by 20 to 30% of the rate of the copper cementation process and reduced by 20% its activation energy. At the same time, the recoveries of nickel, cobalt and iron to the leach solution increased up to 82.2%, 78.5% and 57.1%, respectively, and that of copper to the cement precipitate up to 74%. Optimal process conditions have been identified with respect to the current density, electrode material, copper concentration in solutions and the process temperature. 2.In the process of hydroelectrochemical sulfuric acid leaching of nickel and copper sulfides, the grain size, the phase form of sulfides, the solution composition (H2SO4, Cl?, Cu2+, Fe3+)and the current amperage had an effect on the nickel recovery to the solution, which reached 90%, while the degree of copper transfer to solution did not exceed 20%. The process of hydroelectrochemical sulfuric acid leaching of nickel and copper sulfides with an addition of Cl? made it possible to selectively recover nickel into the leach solution along with concentrating copper in the leach residue. 3.When subjecting samples of commercial-grade magnetic fractions of converter matte to sulfuric acid leaching, the imposition of electric current, the concentrations of sulfuric acid and chloride ion in the solution and the duration of the reaction process had an effect on the process. The nickel recovery was 85% and that of cobalt and iron was 95% and the recoveries reached 97.5%, 98.3% and 99.8% as a result of repeated treatment of the primary residue under similar process conditions. Up to 75% of copper, 75% of sulfur and 99.0-99.5% of palladium was concentrated in the solid reach residues. The experimental data obtained indicates that the use of AC for hydroelectrochemical sulfuric acid leaching for separation of copper- and nickel-containing intermediate products has favorable prospects.

Jan 1, 2003

By Ejike Emmanuel, Nwoye Chukwuka, Ogwuegbu Martin, Asuwaji Ayuk, Onyedika Gerald

"Microwave pre-treatment of cassiterite ore prior to leaching was carried out in an attempt to obtain high grade of Sn02 and to conserve the total energy expended during processing. Microwave treatment was selected due to the presence of associated minerals which behaves differently to microwave energy. Studies in this work showed that microwave pretreatment of cassiterite ore can be applied to increase the recovery of tin oxide within 5 minutes of leaching. Microwave treatment of the ore resulted in mineral liberation at all particle sizes. Tin oxide was separated from the major impurities via leaching in potassium hydroxide solution and precipitation, resulting in 98% Sn02 at pH 7.IntroductionIn the nineties, the available techniques used for ore processing and analysis in Nigeria was the solution methods of either alkaline fusion or acid digestion [1,2]. A process in which cassiterite is made acid soluble by reduction to SnO2 , which stabilizes by glass formation and the tin was extracted by leaching the glass with sulphuric acid, followed by electrowinning was reported [3,4]. In another study, Baba et al [5] studied the dissolution kinetics of a Nigerian casiterite ore in hydrochloric acid solution. The effects of acid concentration,temperature, particle size and stirring speed were examined. It was found that the dissolution rates of cassiterite depends on hydrogen ion concentration, H+, stirring speed and ore particle dimensions. These were believed to report low data due to incomplete solubilization of the ore minerals in aqeous medium [6]. Analytical chemists have used microwave heating devices routinely for the dissolution of metals, minerals and various chemical products in chemical analysis [7,8]. It offers faster heating rate and consequently faster dissolution rate than conventional heating. The principle of the dissolution of analytical samples has been applied to the leaching of various minerals contained in an ore or concentrate sample. Some researchers [9, 10] conducted microwave assisted leaching of laterite ores containing oxides of nickel, cobalt, and iron. The metals of these mineral components were converted into their chlorides by microwave heating (1200 W, 2450 MHz, Nz atmosphere) a mixture of the ore and ammonium chloride between l 77°C and 312° C for 4-5 min, followed by water leaching at 80° C for 30 min. Nickel and cobalt extractions were 70% and 85%, and respectively, and are comparable with roasting at 300°C in a conventional rotary kiln for 2 hours."

Jan 1, 2013

By Dewei Zhu

A general purpose computer model for describing the transport phenomena and resulting rate of deposition in Chemical Vapor Deposition (CVD) processes has been described. Partial differential equations describing the conservation of mass, momentum, energy and chemical species are solved by a computer program employing a finite volume method. The program allows for multiple chemical species and natural convection effects. In this paper, the deposition of silicon by the reaction of silicon tetrachloride and hydrogen in a vertical stagnation flow reactor with rotating substrate has been considered. The effects of reactor pressure and substrate rotation speed on the rate and uniformity of deposition have been studied. The predicted rates of silicon deposition along the substrate are in reasonable agreement with experimental results found in literature. The model can be used as a tool for design optimization of such reactors.

Jan 1, 1990

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

Acid mist generation is a major concern in zinc, copper and nickel electrowinning industries and there is a strong environmental drive to control its emission into the work environment. Foaming reagents are typically added to the electrolyte to alleviate this problem. In zinc electrowinning, Licorice and Saponin are examples of foaming reagents used for this purpose. In order for the foaming reagent to be effective, its foaming behavior must be determined. In this work, a test procedure was developed to study the foaming characteristics of various surfactants for use as foaming agents to control acid mist in aqueous metal electrowinning. This new test was termed as "mini-flotation test" and it was used to study the foaming behavior of a large number of reagents in an industrial zinc sulfate electrolyte under simulated zinc electrowinning conditions (gas sparging). In addition, the influence of important process parameters such as current density, electrolyte temperature, reagent addition level and sulfuric acid concentration on the foaming characteristics of the electrolyte for each surfactant were investigated. The results of this study have identified the most important factors that influence foam formation, growth and stability. This method could be used as a process control for reagent addition in the cellhouse by generating a calibration curve for the optimum electrolyte conditions.

Jan 1, 1997

By R. Boom, C. F. Balentina, J. H. L. Voncken

During vitrification of bottom ash generated from the combustion of municipal solid waste (MSW), a Fe-Cu based alloy phase with great value was formed. In order to find proper commercial use in metallurgical industry, it is necessary to separate Cu and Fe. The present study focuses on the sulfide treatment at temperatures of 1400 – 1500oC, in particular with FeS containing minerals. Various sulfide compounds such as Na2S, Al2S3 and Ni3S2 were added to promote the copper removal. Pyrite and zinc sludge (containing ZnS) as waste streams were studied with specific interests. The results showed that both zinc sludge and pyrite are effective for copper removal with the highest removal efficiency of 95% by using pyrite. The copper content drops from 12 wt% to about 2 wt%. However, it is still difficult to remove copper completely from the alloy in one step, and a multi-step operation is needed.

Jan 1, 2008

By J. E. Sallee

An experimental study has been conducted on the level of arsenic contamination in samples of zinc oxide when the zinc oxide is contacted with gas mixtures containing As4O6(g). This contamination has been determined as a function of A4O6 saturation pressure, temperature, zinc oxide sample surface area, impurities, and oxygen level in the gas mixture. The results indicated a rather clean separation can be achieved between condensed zinc oxide and gaseous arsenic oxide as long as attention is given to temperature control, and the final zinc oxide surface area. For a 300°C operation temperature and an AqOg saturation pressure of 0.38 TORR (or 0.05% As406 by volume), the contamination level is expected to be approximately 100 ppm. This suggests that arsenical dusts can be treated in the HRD flame reactor process and a reasonable purity zinc oxideproduct produced. The results also show no evidence of zinc arsenite or zinc arsenate formation.

Jan 1, 1994

By Steven M. Puricelli

Sulfuric acid plants associated with smelters, have historically been an overworked and often neglected pollution control device. They could do little more than manage the wide fluctuations in gas flow and SO2 strength from the smelter. With the introduction of flash smelting, the picture began to change, but the fluctuating batch converters continued to dictate acid plant design. More recently, the commercial use of continuous converting processes utilizing high levels of oxygen enrichment has dramatically upgraded the SO2 strength and stabilized the gas flow to the acid plant. The SO2 gas now issues continuously and at concentrations that allow for compact and, cost effective acid plants. Relieved of the burden of excessive dilution air, the heats of reaction can also be recovered as medium pressure steam and used to drive a generator, making the acid plant a net producer of power and a valuable asset to balance sheets. This concept was put into practice at the Kennecott Utah Copper Corporation smelter modernization project, located in Salt Lake City, Utah. The new acid plant, which was commissioned in June of 1995, is a sophisticated, low environmental impact, energy producing plant, worthy of review. This paper examines the key features of this acid plant, such as controlling its tail gas, by catalysis alone, to an environmentally friendly, 100 ppm of SO2, while feeding the acid plant converter with an efficient 14% SO2. The acid plant is also a prudent steward of energy resources, recovering 220,000 lb/hr of 140 psig steam from process heat which is used to generate a substantial 20 MW of gross power. Also discussed will be some of the ongoing issues, such as handling of selenium and fluorine in the gas cleaning sections, as well as a review of some. of the problems that were identified and resolved. Today's modem acid plants, by necessity, are becoming a producer of quality, valuable products, making the acid plant an asset and not a liability. Plants like Kennecott are already gaining wider acceptance and are expected to be the vision of the future.

Jan 1, 1998

By W. F. Whittaker

Systematic control of process parameters during electrorefined copper cathode production and final product inspection ensures high quality of produced "ORC brand copper. Since 1986, substantial increases in tankhouse productivity have been achieved by a number of technological and process control changes. This paper reviews the changes implemented to achieve higher productivity and cathode quality.

Jan 1, 1992

By Rodney L. Williamson

Vacuum arc remelting (V AR) is an industrial metallurgical process widely used throughout the specialty metals industry to cast large alloy ingots. Part of the V AR control problem consists of adjusting arc current to control electrode melt rate which also depends on the electrode temperature distribution. Because the temperature distribution responds very slowly (1-4 hours depending on size and material) to changes in melt power, the melt rate response is history dependent and highly nonlinear. The situation is complicated further because measurement of the electrode temperature distribution is not practical. To solve the problem of accurate, responsive melt rate control. a low order electrode melting model has been developed and incorporated into a V AR process controller. Data from laboratory and industrial tests show that the goal of responsive, accurate melt rate control has been achieved, even when melting under highly dynamic process conditions. Keywords: Vacuum Arc Remelting. Model-Based Control

Jan 1, 2003

By I. A. Ibrahim, A. K. Ismail, A. A. I. Afifi

"Synthetic rutile for paints industry is conventionally produced by a combined smelting and leaching process. Smelting process is an energy intensive step and represents economic burden in view of the increasing energy costs. Egyptian ilmenite ore containing 40% TiO2 and 38% total Fe was thus directly leached with sulphuric acid to produce eventually synthetic rutile. The process-involves digestion of the ore with sulphuric acid whereby both TiO2 and Fe are dissolved. The solution was then treated with iron powder to convert Fe3+ to Fe2+ to avoid co-precipitation of iron during the hydrolysis step. After solid/liquid separation and clarification, Fe was crystallized as ferrous sulphate hydrate by chilling. The titanium pregnant liquor was concentrated by evaporation and then hydrolyzed to precipitate hydrated titanium dioxide which was then calcined to produce synthetic rutile containing 98.6 TiO2 and 0.58% Fe2O 3. The optimum conditions of all the processing stages were determined.IntroductionSynthetic rutile for paints, welding rods and other industries could be produced from ilmenite ore by sulfuric acid leaching process. This process is a batch process and nearly 80% of all TiO2 produced in the world is made by this process [1]. Figure l shows simple block flowsheet of the process. The process involves the following stages.Digestion: In this stage, ilmenite ore is treated with concentrated sulfuric acid where both iron and titanium are converted to their respective sulfates according to the following equations:"

Jan 1, 2000

By Christina V. White

An experimental study was undertaken to investigate the feasibility of utilizing vapor transport for the treatment of heavy metal contaminated smelter soils. The focus of this project was to develop process chemistries that would make incineration a viable process for the treatment these soils. The experimentation concentrated on the elimination of arsenic, cadmium, and lead, and was performed in a laboramry scale rotary kiln setup. Three soil samples from non¬ferrous smelter sites, which contained various concentrations of contaminants, were utilized in the experimentation. Three chemistries were investigated for the volatilization of the heavy metals: Chloridizing volatilization, ferric chloride vapor complex formation, and the use of oxygen potential control. The samples were analyzed for residual heavy metals so that the extractions could be determined. However, the ultimate test was the leachability of the residual arsenic, cadmium, and lead, as determined by the TCLP test. The results firmly establish that incineration is a feasible process for the treatment of metal contaminated soils. It was found that no one process chemistry is suitable for all different soil samples. A two-step process consisting of a reducing step followed by a hydro-chlorination step was required to make Soil Sample-B pass the TCLP tests for all three heavy metals. Soil Sample-A passed the TCLP tests for arsenic, cadmium, and lead using a hydro-chlorination process at a minimum temperature of 700°C. In addition to passing the TCLP mm for Soil Sample-A and Soil Sample-B, 70 to 80 percent removal of the impurities was accomplished. This demonstrates that the leachability of the impurities was decreased primarily due to the removal of a large fraction of the contaminants, Soil Sample-C possessed very high levels of cadmium and lead and only moderate extractions of the impurities were generated from this soil. The arsenic TCLP test was passed at 500'C using a process gas containing ferric chloride and at temperatures of 700°C and above using chlorination of hydro-chlorination.

Jan 1, 1996

By Richard D. Hagni

Reflected light microscopic examination of particles from laboratory experimental copper flash furnaces operated under varied furnace conditions shows that the particles exhibit a wide range in mineral compositions and mineral abundances that correlate with partial pressure of oxygen and concentrate/oxygen ratio. Chalcopyrite, bornite, and digenite are more abundant under low oxygen conditions. With increasing oxygen, metallic copper, delafossite and cuprite become increasingly abundant. The extent of particle agglomeration during flight varies with the furnace. Those products from the larger furnaces exhibit the greater degree of agglomeration. Significant particle fragmentation also is evidenced by cracking and brecciation of some particles.

Jan 1, 1991

By Roderick 1. L. Guthrie, Mei Li

"A mathematical model was developed to study the role of orifice shape in the detection of inclusions in LiMCA (Liquid Metal .cleanliness Analyzer) system. The fluid flow field within the ESZ was obtained by solving the Navier-Stokes equations. The trajectories of entrained particles were calculated using the equations for motion of particles. A numerical study of the effect of orifice shape on signal shape generated by inclusions passing through orifice showed that the signals in a parabolic orifice are gaussian in shape, while those in a cylindrical orifice are trapezoidal in shape. This signal shape difference needs to be taken into account when performing particle discrimination. Orifice shape influences also pass-through fraction of inclusions. Finally, a study of the orifice shape on critical conditioning currents suggested that as the polynominal coefficient of the parabolic orifice increases, the critical conditioning current, which is also the maximum operating current, decreases dramatically. These critical conditioning currents also increase as the fluid flow velocity within the ESZ increases. IntroductionThe presence of non-metallic inclusions in metals often leads to impaired mechanical properties such as a reduction in fatigue strength, and to processing problems such as tear-offs in deep drawing and increased breakage rates in wire drawing operations. Similarly, inclusions cause a variety of surface defects in rolled or extruded products.Prior to the development of the LiMCA system (1) at McGill University in the early 1980's, it was not possible to measure inclusions, in situ, in liquid metals. Compared with other techniques, such as sedimentation, filtration and metallography, which require considerable amounts of labor and time, the LiMCA method has the advantage of providing not only information on the volume concentration of inclusions, but also on the size distribution of inclusions immediately and quantitatively."

Jan 1, 2001

By D. E. Larson

In cooperation with the National Institute of Environmental Health Science and the National Institute for Occupational Safety and Health the U.S. Bureau of Mines conducted grinding research on non-asbestiform tremolite. The goal of this effort was to prepare ground tremolite samples containing a considerable percentage of acicular grains with aspect ratios (approximately = 8um long with widths = 1 um) similar to those of asbestos particles suspected of causing cancer, Optical-and electron-microscopic examinations were used to monitor the size and shape of the grains in the ground products. Although customized milling techniques do have noticeable effects in producing acicular grains, the prismatic nature of fracturing in the non-asbestiform tremolites limited the number of acicular grains that could be purposely produced, and indicates that the likelihood of high concentrations of acicular particles occurring under normal mining and milling conditions is small.

Jan 1, 1991

By S. Malinov, J. J. McKeown, W. Sha, S. McShane

"A model is developed for prediction of fatigue stress life S-N diagrams for Ti-6Al-4V alloy at different conditions, using Artificial Neural Network (ANN). Different factors which have influence on the S-N diagram are involved as input parameters of the NN, namely microstructure, environment, texture, test/work temperature, surface treatment and stress amplitude. As the output the S-N fatigue diagram is simulated and plotted.The model is based on standard multilayer feedforward neural network. The NN is trained with a comprehensive data set collected from the literature, using Levenberg-Marquardt training algorithm in combination with Bayesian regularisation. A very good performance of the trained Neural Network is achieved. Good correspondence between ANN"" prediction and experimental S-N diagrams is observed. Using the model S-N diagrams for different conditions are predicted and analysed. Graphical User Interface is developed for use of the model. We believe that the model will be important for practical applications in solving various problems on fatigue behaviour of the titanium alloy.IntroductionTitanium and its alloys have an increasing range of applications due to their very good combination of mechanical properties, corrosion and erosion resistance. They are currently finding widespread applications in many industries due to their desirable and versatile properties. Most important among the alloys is Ti-6AI-4Y. Jet aircraft manufacturers are the principal 'consumers of Ti-6Al-4V and it is often specified for critical parts, the failure of which could result in the loss of an entire system. A generic class of Ti-6AI-4V has been developed over the past years and it has become the best understood of all the titanium alloys. The advantages of titanium alloys include: (i) low densities, giving very attractive strength to weight ratios allowing lighter and stronger structures; (ii) superior corrosion and erosion resistance in many environments; (iii) high temperature capability. Although the titanium materials are still considered as expensive materials, for many applications the cost of titanium alloys can be justified on the basis of their desirable properties."

Jan 1, 2001

By S. W. Ip

Over the years, the importance of surface and interfacial phenomena has been neglected by the copper-nickel industry. As a result, little data on the surface and interfacial tension of the Ni matte and slag system are available in the literature. In view of the scarcity of information in this area, the surface tensions of the Ni-Fe-S system together with the Ni-Fe-S and fayalite type slag system were measured using the sessile drop technique. Drop images were obtained by X-ray radiography. For the Ni-Fe-S system, the results showed that the surface tension of the matte increases with matte grade. The surface tension behavior with changing matte grade showed a slight negative deviation from ideality. This indicated that FeS is slightly surface active in the nickel matte system. Results also indicated that small increase in sulphur content in the matte can decrease the surface tension quite significantly. The measured surface tension of the Ni-Cu-S system showed a linear relationship with the Cu2S content in the matte. The surface tension decreased with Cu2S content. Interfacial tension measurements showed a similar trend. That is, interfacial tension increased with increasing matte grade. The presence of MgO (-1.5%) and A12O3 (-6%) in the slag does not affect the interfacial tension value. Effects of matte surface tension on phenomena such as entrainment of matte in slag and infiltration of matte into refractory pores are discussed. The calculated flotation coefficients indicated that flotation of nickel mattes cannot be avoided by changing the matte grade. Filming of matte on bubbles can occur below a matte grade of about 19% Ni3S2. As for infiltration, refractory bricks containing high Cr2O3 will be easily wetted by matte regardless of matte grade. Therefore, bricks containing high Cr2O3 can easily be infiltrated by liquid matte.

Jan 1, 1993

By Edward P. Hagarty

The Hazardous and Solid Waste Amendments (HSWA) of 1984 added Subtitle I to the Resource Conservation and Recovery Act (RCRA), authorizing the Environmental Protection Agency (EPA) to develop and implement a new regulatory program for Underground Storage Tanks (USTs) containing petroleum and other regulated substances. Technical standards required for release detection, prevention, and correction as necessary to protect human health and the environment were promulgated as described in 53 Federal Register 37082 (September 23, 1988). Virginia State Regulations (VR 680- 13-02) and U.S. Army Regulations require that a Corrective Action Plan and a Site Clearance Report be prepared to explain the details of remediation of any contaminated media. Construction of new buildings is proposed in two different areas at Fort Myer in Arlington, Virginia, where USTs containing gasoline, diesel and heating oil were located. Tightness testing performed on these USTs in September 1991 indicated that some of the tanks were leaking. Many of the tanks were removed for permanent closure. Initial Abatement (excavation of contaminated soil) was &ed out immediately. A detailed Site Characterization Study which included Hydropunch", field screening using immunoassay, and pilot test - dual phase (water and soil gas) extraction was conducted. Environmental media were analyzed for volatiles, semi-volatiles and metals. A detailed risk analysis (RA) was performed to determine risk-based clean up levels for benzene, toluene, ethylbenzene, xylenes (BTEX); polycyclic aromatic hydrocarbons (PAHs); and methyl-tertiary butyl ether (MTBE). The RA also discussed the presence of lead in the soil. Before constructing any buildings in these contaminated areas, remediation must be conducted in accordance with the State, Federal and other applicable regulations. The remedial alternatives evaluated included Vapor Enhanced Groundwater Extraction, Soil Vacuum Extraction, Soil Washing, Soil Steaming, Active and Passive Ventilation SolidificationlStabilization, Vapor Barrier Construction, and Excavation with Off-site Disposal. This paper discusses: (a) delineation of soil contamination @) risk analysis (c) evaluation of remedial alternatives and selection of the most appropriate technology and (d) consideration of various regulatory issues.

Jan 1, 1994

By Suguru Kohno, Yoshihiro Momose, Masakazu Honma, Tokirou Kamosawa

Copper metal surfaces have been examined by an extremely sensitive surface analysis technique called temperature programmed photoelectron emission (TPPE). The surfaces were ultrasonically cleaned and subsequently abraded by a screw in organic solvents and water. The TPPE apparatus is composed of a Geiger counter with Q gas (He+ iso-C4H10). The curve of photoelectron emission (PE) intensity vs. wavelength from 300 to 170 nm, termed PE spectrum, was repeatedly measured at different temperatures in the temperature- increase process from 25 to 350°C. The number of emitted electrons in a PE spectrum (PE total count) increased, reached a maximum at-250°C, and decreased with increasing temperature. With the surfaces cleaned alone in the liquids the maximum PE total count decreased in the order C3H70H > (CH3) 2CHOH > C2HpH > CHPH > H2O. With the mechanically abraded surfaces in the liquids the maximum PE total count changed as a function of the abrasion period and the maximum tended to appear at higher temperature with increasing abrasion period; the maximum value at 10-min abrasion decreased in the order H2O > CHpH > C2HPH > (CH3) 2CHOH > n-C3HpH. It was suggested that the TPPE behavior can be related to the acid-base interaction between the alcohols and the abraded metal surfaces and the presence of a contaminant over layer on the surface. From the XPS analysis of the 01 s spectra it was suggested that the chemical change of the adsorbed oxygen to oxide oxygen with temperature plays a substantial role in the appearance of the maximum PE total count.

Jan 1, 2000

By Mitsuhiro Ito

"To allow various wastes containing high levels of chlorine to be used as alternative raw materials for Portland cement, two practical methods of chlorine removal were developed. In the first method, chlorine is extracted from the wastes during the cement manufacturing process. In the second, ash-dust waste with high chlorine content is first washed and then dehydrated to cake before being introduced to the cement manufacturing process. This cake can be used as an alternative for some cement raw materials. By combining the two methods, various wastes previously considered unsuitable for recycling due to their chlorine content can often now be used in cement manufacturing plants. As such, these methods represent a major contribution to environmental protection as well as a solution to problems relating to the diffusion of heavy metals and dioxins from cement plants.1. IntroductionWaste generation levels have risen rapidly in recent years. in both the consumer and industrial sectors and today, the need for effective, efficient waste management is one of the most pressing and serious problem of today's society.The Japanese cement industry has reacted to the increase in waste generation by using certain materials as alternative raw inputs or fuels for cement production, in an effort to contribute to society and conserve energy resources.These wastes often contain non-negligible levels of chlorine and heavy metals, however, both of which are unsuitable for cement production. Depending on the element content, Heavy metals have a particularly negative effect -on cement quality; in addition, they can be released into the environment. Chlorine, on the other hand, is contained in large amounts in incinerated ash from household wastes as well as in certain plastics. Both substances are considered impediments in cement-production, not only because they reduce the quality of the cement produced but also because they impair operating safety on cement production lines.To address this problem, two practical technologies have been established for separation and recovery of chlorine components during cement pre-processing and production. This paper introduces the application of these technologies with a special focus on incinerated ash from urban wastes, a representative form of waste material having notably high concentrations of chlorine, heavy metals, and dioxins. We also outline the technologies enabling this material to be used as an alternative input to cement production."

Jan 1, 2000

By Leonard Harris, Rosa H. Harris

"It is becoming increasingly obvious to mining and exploration companies, when operating overseas, that their activities should not conflict with the interests of the surrounding communities. The world's largest gold heap leach operation, Minera Yanacocha has installed community assistance programs in Peru concerned with health, education, electrification, agricultural assistance and road improvements. The programs are conducted with joint venture partners consisting of the company, the community people, the contractors and suppliers, government and non government organizations and a ladies association composed of the employees' wives and female staff.IntroductionThe l 990's is the decade highlighted by enormous investments in mineral exploration and mining projects in the developing world. Figure 1 illustrates the distribution of exploration spending by mining companies in 1995."

Jan 1, 1997