Search Documents

By Sabine Knoll

The thermodynamic properties of four liquid ternary zinc alloys, Au-Sn-Zn, Ag-Sn-Zn, AI-Sn Zn and Cu-In-Zn were measured with an electromotive force (emf) method at three or four cross-sections with an constant X:Sn or Cu-In ratio. At the Au-Sn-Zn and AI-Sn-Zn system calorimetric measurements were also carried out in order to compare the integral enthalpy of mixing from the direct measurements with the data of the emf measurements, which were derived by Gibbs-Duhem integration.

Jan 1, 2003

By Y. Fukunaka, M. Niinae, E. Kusaka, T. Kuzuya, R. Ishii

"Samarium oxalattr particles was precipitated in oxalic acid aqueous solution from samarium-loaded D2EHPA solution emulsified with a conventional impeller. The calculated fractional precipitation of samarium oxalate was reasonably compared with the value determined by chemical analysis. Morphological variation of oxalate precipitate particles was then examined with H2C2O4 concentration in aqueous solution, Sm(III) and D2EHPA concentrations in organic phase. The needle-like precipitate was identified as Sm2(C2O4)3 10H2O by XRD. Precipitates obtained at higher H2C2O4· or Sm(III) concentration greatly decreased the length of major axis of precipitate, while those at higher D2EHPA concentration increased it. The oxalate was further precipitated under ultrasonic irradiation. However, the morphological variation caused by theses processing variables was not so evident under ultrasonic irradiation as in an impeller or shaking mixer.IntroductionThe materials processing of the rare earth elements must be reviewed from the scope of industrial ecology, since they have the potential applications of magnetic materials as well as secondary battery in developing programs of the electric vehicle. The technological trend to develop the electric vehicle may greatly influence the concept of materials processing, since the global· environmental problem must accommodate with the sustainable development for mankind. The recycle design must be a key issue in the materials science and engineering.Solvent extraction provides a unique separation technology -in this sense. Doyle (1)(2) reported the integrating solvent extraction with processing of advanced ceramic materials, whose chemical composition and microstructure must be precisely controlled. In her paper, the higher productivity inherent to the present process superior to hydrolyzing metal alkoxides was emphasized. Oxalic acid has been used as precipitant for rare earth purification process, since rare earth oxalate has a very small solubility in water and can be easily decomposed to oxide. It is thus suitable for precipitation stripping agent in cationic exchange type extracting system (i.e. D2EHPA, VA-10, PC-88A and so on)."

Jan 1, 2000

By Liyuan Chai

The corrosion mechanism of A3 steel induced by chloride ions in the purified water had been investigated with the A C Impedance technique. The results showed that there were another two factors which determined its electrochemical corrosive rate: the electrode potential and coverage ratio of chloride ions on the surface of A3 Steel. The corrosion mechanism of A3 steel in the solution with chloride ions emendation was two steps of electrode process with the rate-determining step of 0,32kFeClFeCle+--¾¾®++.

Jan 1, 2009

By Guangwei Wang, Changle Zheng, Yifan Chai, Jian Guo, Weiwei Geng, Jianliang Zhang

In this paper, characteristic and kinetics of CO2 reaction with four different kinds of coke such as top-loading coke, dry quenching tamping coke, wet quenching tamping coke and semi-coke were investigated based on isothermal method. Electric resistance reduction furnace was used to heat the sample. Volume Model (VM) and Shrinking Core Model (SCM) were used to calculate the kinetic parameters and to contrast with the experimental results. The results showed that the Volumetric Model (VM) was much suitable for the reaction of top-loading coke, dry quenching tamping coke and wet quenching tamping coke, while Shrinking Core Model (SCM) was much suitable for semi-coke.

Jan 1, 2015

By Chuanfu Zhang

Based on Thermogravimetric and Differential thermal analysis (TGA-DTA), porous copper powder is prepared by thermal decomposition of complicated copper oxalate. The effects of various conditions on the morphology, crystalline grain size and specific surface area of copper powder were investigated, including temperature, duration, mixing ratio of nitrogen and hydrogen. Furthermore, composition and morphologies of the products were characterized by X-ray diffraction (XRD), Scanning electron microscope (SEM) and BET adsorption isotherm. It is found that porous copper powder was produced under optimum conditions. The specific surface area is over 6.74 m2?g-1, and average pore size in particles is about 30.3 nm. After comparison of SEM images, the final product Cu well inherits the morphology of the precursor, thus a mechanism of in-situ decomposition is proposed.

Jan 1, 2009

By Xiang Zhu

Xidagou is the largest waste water discharge channel of the Anshan Iron and Steel Complex (AISC) with average flow rate of 8000 cubic meters per hour, which is about 75% of the total effluent of the AISC. The waste water from Xidagou seriously polluted the Taizi River Basin. In order to meet the Chinese Class V Standard for Surface Water Discharge and the Standard for Recycled Industrial Water Reuse, with the aid of the World Bank, the AISC began the treatability studies in 1991. Based on the bench-scale test, the AISC carried out pilot-scale treatability studies on three different treatment processes and five different chemical coagulants for more than half a year in 1992. The study results show that the processes of primary sedimentation- chemical mixing and flocculation-secondary sedimentation-filtration can meet the requirement and that PFS and PAM are effective and economic chemical coagulants.

Jan 1, 1994

By Masanori Abe, Yoshitaka Kitamoto, Kazuhiro Nishimura

"Ferrite plating is a chemical processing which utilizes Fe2+ - Fe3+ oxidation to synthesizing polycrystalline films of ferromagnetic spinels (MFe20 4, M = Fe, Co, Ni, Zn, Al, Cr, TI, etc:) directly from an aqueous solution at 24 - 100°C. This low temperature process allows us to fabricate new ferrite film devices on · substrates of such non-heat-resistant materials as plastics, GaAs integrated circuits, and biomaterials. Synthesized from an aqueous solution the ferrite plated ·films are highly biocompatible. Thus various magnetic device and biomedical applications have been proposed and realized using ferrite-plated films. Ferrite-encapsulated polymer microspheres are applied to antibody carries for enzyme immunoassay, and also to toners/carriers for photocopying. Perpendicular magnetic recording media utilizing plated CoNi ferrite films are proposed. The low-temperature synthesized films of NiZn and Co ferrites are potentially used as soft-magnetic and/or insulating layers, respectively at high/microwave frequencies.IntroductionFerrite plating is a processing which facilitates the formation of crystalline spinel ferrite films with various compositions, (Fe, M)30 4 (M = Fe, Co, Ni, Zn, Al, Cr, TI, etc.), directly from an aqueous solution at 60 - 100°C [1]. This opened the door to fabricating novel ferrite-film devices using substrates of such non-heat-resistant materials as plastics and GaAs integrated circuits [2-4]; conventional ferrite film preparation techniques such as sputtering, vacuum evaporation, MBE, LPE, etc., require high temperatures(> -600°C) for crystallization of ferrites, which deteriorates the non-heat-resistant substrates. Recently we extended ferrite plating to be preformed at room temperature [5, 6]. This enables us to use as substrates such organic materials as biomaterials (e.g. enzymes) having very low heat-resistance."

Jan 1, 2000

By Larry G. Twidwell, Jannette L. Chorney, Bryce D. Ruffier, Katelyn M. Lyons, Daniel W. Gaede, Ryan J. Foy, Jerome P. Downey

The Army Research Laboratory (ARL) has an interest in the recovery and processing of rare earth elements. At Montana Tech, elevated temperature chlorination of rare earth oxides is presently being investigated as a potential methods leading to the selective separation and recovery of rare earth elements from mineral ores and concentrates. After preliminary evaluation, ytterbium oxide was selected as a representative surrogate material for more extensive chlorination studies. Methods used to determine the conversion and recovery include X-ray diffraction (XRD) and inductively coupled plasma (ICP) analysis. These data have been used to establish and confirm process conditions that consistently yield high conversion efficiencies. Based on the promising results, further experimentation is underway to ascertain the metallurgical response of other rare earth oxides and carbonates to the roasting process. The end goal is to create a robust process for industrial application that has greater efficiency and reduced costs as compared to current practice.

Jan 1, 2015

By Lawrence L. Brown

As part of the Federal effort to help maintain an adequate supply of fertilizer materials, the Bureau of Mines conducted research to characterize complex low-grade Michigan phosphate materials and to devise methods for recovering fertilizer-grade phosphate concentrates. The rock is from middle Precambrian sedimentary formations in the Marquette Range located in the central part of the Upper Peninsula of Michigan. Occurrence of phosphate-bearing sediments in Precambrian rocks is rare. This deposit, containing 12 to 15 pct P2O5 is believed to be the richest Precambrian phosphate deposit in the United States. Petrographic examination showed that the conglomeritic rock contains crystalline apatite both in "black pebbles" and in quartz matrix. Attrition scrubbing and sizing tests showed that there is no tendency for phosphate to concentrate in any of the sized fractions. In beneficiation tests, which included grinding to minus 325 mesh followed by phosphate mineral flotation using a fatty acid-fuel oil collector, a phosphate concentrate was obtained that had a grade of 30 pet P2O5 and a P2O5 recovery of 72 pct. This concentrate should be suitable for fertilizer manufacture.

Jan 1, 1982

By Wang Jia, Chai Li-yuan, Zhang Jin-Long, Peng Bing, Zhang Qiang

"Electrolytic manganese dioxide (EMD) residue was mixed with shale and fly ash as the main materials to make solidification/sintering brick for the utilization of the residue from EMD production. The effects of sintering temperature, sintering time, solid waste content and cooling process on its mechanical properties and toxic elements solidification were investigated according to compressive strength and leaching toxicity. The results showed that the calcined residue had capability of solidifying toxic metals and exhibited perfect strength after treated in the optimal parameters of EMD residue below 50%, temperature at 1000-1100°C, time3-5h, and semi-quenched at 600°C1 InstructionSolid clay-brick holds the leading position among building materials for a very long time in China. The traditional technique of making clay-brick has the drawbacks of backward process, simple facilities and single product. Since Chinese Reform and Opening-up, urban-rural construction and real estate have been booming with the rapidly development of national economy and science technology. The problems of ruining fertile land, environment contamination and high energy consumption in the traditional technique of clay-brick making have not been solved yet. On the other hand, more than 7 billion tons of industrial wastes are accumulated over years which occupies over 6.7 million hectares filed and causes serious environmental problems[1-31. Strategy present in ""The Chinese Agenda of the 21st Century"" required the production of wall materials less energy conservation, land saving and waste recycling.Coal gangue[4-9l, fly ash[I0- 13l, sludge from waste water treatment and tailings of gypsum, pyrite, copper mine, high silicon containing iron, asbestos and ects [l4-lSJ are the solid wastes used for brick making around the world. There are two kinds of process for brick making, high temperature sintering and low temperature steam curing[19•201. Although the technology of two brick making made great progress and got widely application in construction field, no precedent for preparing sintering-bricks with EMD residue as materials occurred in China because of its complicated processing technics and lack of sufficient practical experience to guarantee the bricks' quality.In this study, EMD residue was mixed with shale and fly ash as the main materials to make solidification/sintering brick. The effects of sintering temperature, sintering time, solid waste content and cooling process on its mechanical properties and toxic elements solidification were investigated according to compressive strength and leaching toxicity."

Jan 1, 2011

By Signe Kjelstrup, Leiv Kolbeinsen, Marit Takla, Odne Burheim

"This paper presents a Seebeck-type solid state thermoelectric power generator unit, designed to investigate the possible recovery of radiant waste heat at a silicon plant in Norway where roughly 703 of the total input energy leaves the process as waste heat. The unit is 0.5 m x 0.5 m and is built of 36 commercially available thermoelectric devices based on bismuth telluride p - and n - type semiconductors. Thermoelectric devices directly convert fractions of a heat flux into an electric current (and vice versa) and may therefore be convenient for recovery of waste heat when the heat source is discontinuously available. The purpose of the thermoelectric unit is to give a proof of principle of direct thermoelectric energy conversion on a large scale. We present the initial test results for the generator. At an average temperature difference between the heat reservoir and the heat sink of 98°C, we measured an open ciruit potential of 23.44 ± 0.06 V and the matched load power output was 39.4 W. At a temperature difference of 220°C, we predict the generator open circuit potential to be 40.8 V, which corresponds to an efficient Seebeck coefficient of 242 µV /K, and matched load power output to be 120 W.IntroductionThe world's power demand increases, driven by population growth and increase in living standards and simultaneously global warming is recognized as one of our most serious environmental problems. According to the International Energy Agency[l], the industrial sector accounted for approximately one third of the total global power consumption in 2005. Increasing the energy efficiency of industrial processes thus represents a benign and substantial route for addressing environmental concerns and energy security.In accordance with the second law of thermodynamics, all real processes are associated with lost work which is energy being dissipated as heat to the surroundings[2]. Improving the energy efficiency of industrial processes is about finding the process path associated with a minimum of lost work. The more evenly the losses are distributed, the smaller are the losses [3, 4]. In addition, exploiting the unavoidable waste heat will contribute to improve the energy efficiency. The waste heat may be utilized for heating purposes and/or it can be upgraded to work for instance via some sort of heat engine."

Jan 1, 2012

By Eiji Iwamura

"Two types of diamond-like carbon (DLC) films with different microstructures were prepared by unbalanced magnetron sputtering, and the tribological properties of the nanoscaled DLC multilayer coatings consisting of alternating layers of graphitelike and amorphous-like microstructures were examined. The DLC microstructure was characterized by certain features of graphite-like clusters, in that some of them had onion-like structures. The films filled with the clusters were obtained in a condition with an incidence of high influx of energetic electrons, and the other films without apparent cluster structures were formed in a condition with ion bombardment controlled by negative bias voltage applied to substrates. Stacking each film layer-by-layer, the nanoscaled multilayered coatings showed superior tribological properties to individual single-layered films due to the combination of properties induced by the difference of microstructures.IntroductionIn various tribologiql applications, it is necessary for diamond like carbon (DLC) coatings to have adequate adhesion, significant hardness and a concomitant low friction coefficient. A number of deposition techniques and coating structures have been proposed to achieve suitable DLC properties [1-3]. However it is still difficult to obtain a satisfactory level of combination of the properties particularly desirable for engineering applications.In this study, the features of unbalanced magnetron sputtering were demonstrated with the effect of ion and electron bombardment. Two types of microstructures , namely amorphous-like and graphite-like, were prepared by changing the condition of the charged particles bombardment during deposition. Using the difference of properties induced by the microstructures, nanoscaled DLC multilayered structures were examined in an attempt to improve tribological properties."

Jan 1, 2000

By Jorge Alberto Soares Tenório, Romano Espinosa, Felipe Fardin Grillo, José Roberto de Oliveira, Denise Crocce

"The aim of this work was evaluation of the recovery of Zn and Fe of the EAFD added to the hot metal in the form of briquette at temperature of 1500°C. The EAFD was agglomerated by cold briquetting and introduced in the hot metal. This study utilized a bench-scale equipment to melt, during this process to kept a flow rate of inert gas above the bath. Were collected periodically metal samples and the samples were analyzed for determination of the content of total silicon and carbon by chemical analysis. Zinc oxide, zinc ferrite and other oxides were reduced and were volatized and collected by a cleaning system of dust (baghouse) located on top of the oven. More than 98% of iron were recovered from EAFD during the test. It was possible to produce a dust containing about 68% zinc by means of adding of EAFD.IntroductionIn the first semester of 2010, steel production was about 706 million tons, 27.9 % more than in the first half of 2009. Not a significantly increase if 2010 data is compared with the first semester of 2007 (only 7.2 % higher), before the world’s economic crises. Steel production is divided into two main routes. The first one, and most used, is the Basic Oxygen Furnace Process (BOF process), which in 2008 accounted for approximately 67.1 % of steel production. The second route is carried out in the Electric Arc Furnace (EAF) that in 2008 represented 30.6 % [1 ].Electric arc furnace dust (EAFD) is a solid waste generated during the steel making process. It is classi?ed according to NBR 10004 as dangerous solid waste-class I, because the elements Pb e Cd leach in water exceeding the maximum limits permitted by the NBR 10004 [2 ]."

Jan 1, 2012

By Jiayan Li, Yi Tan, Yao Liu, Yaqiong Li, Shenrui Wu

"A metallurgical grade silicon (MG-Si) refining concept process was presented. Under vacuum conditions, silicon was selectively oxidized by high purity silicon dioxide to form gaseous silicon monoxide while impurities with low vapor pressure in MG-Si were rejected in residue; Then high purity silicon was obtained from the disproportionation of condensed silicon monoxide; and by-produced silicon dioxide was recycled for the oxidation step. Thermodynamics on boron rejection during the oxidation were studied in this work. In the temperature range of 1200-1800K, the saturated vapor pressure of boron, and the Gibbs free energy changes, the equilibrium partial pressures of silicon monoxide and boron oxides of potential reactions were calculated. And the effect of boron activity in MG-Si was also discussed. The results indicated that boron in MG-Si can be rejected during the oxidation and it showed the potential for the further development of the new refining process.IntroductionAs global energy consumption growing dramatically, higher prices of energy and global warming problem have attracted more and more attention [1]. As a clean and renewable energy industry, the photovoltaic (PV) industry converts solar energy to electricity using solar cell device and has a growth rate of about 30% in recent years. It has caused a shortage of silicon feedstock due to that about 90% of solar cells are made of crystalline silicon. And high energy consumption during the production of silicon material, i.e. solar grade silicon (SoG-Si), is main obstacle for its mass production."

Jan 1, 2012

By Lin Li, Xiang Li, Yifang Zheng, Jilai Xue, Jun Zhu

"Al drops and gas bubbles in the anode-cathode space of aluminum electrolysis cell are of great importance for cell operation improvement in metal loss, current efficiency and energy consumption. A direct observation on the Al drop, gas bubble and ultrasound was carried out through a see-through cell. The Al drop immersed into the cryolitic melt was found moving up and down irregularly in the anode-cathode space without electrolysis, which was then completely dissolved into the melt. During electrolysis, the Al drop came to the anode area and reacted with the gas bubbles generated on the anode. Under ultrasound, the gas bubbles were removed from the anode surface while the Al drop was kept on the side of anode. The observed phenomena were useful for technology improvement in reducing the anode-cathode distance or lowering the energy consumption in aluminum electrolysis.IntroductionDuring aluminum electrolysis, aluminum metal drop and anodic gas bubble are in close contact each other within the anode-cathode space, and the interaction between them can produce significant impact on metal loss, current efficiency and energy consumption. The motions of the Al drop and the gas bubble are also related to the dissolution of aluminum metal into cryolitic melt and the cell voltage drop due to the bubble layer covering the anode surface.A number of studies have been carried out using different types of see-through cells, where the dissolving process of metal Al into cryolitic melts (metal fog) in the anode-cathode space was directly observed and photographed [1, 2]. With the similar method, some direct observations on the anodic bubble behaviors with and without ultrasound were performed during aluminum electrolysis [3-6]. However, to our best knowledge, there is no published work on direct observation on the behavior of Al drops and anodic gas bubbles staying together within the same anode-cathode space, as well as the motion and interaction of them in cryolite-alumina melts."

Jan 1, 2011

By Nobuo Kikumoto

Recently, the treatment of industrial waste materials has been a serious social problem here in Japan. Filling them in ponds is now strictly prohibited due to a limited land area and incineration method is also regulated as not to generate DXN. In these conditions, Onahama Smelter has begun to treat shredder dusts (SD) of car at reverberatory furnaces to recover various metals such as copper, gold, silver and palladium without generation of DXN. The total volume of these dusts is expected more than 1 million metric tonnes a year in Japan. Onahama Smelter is now planning to treat about 20% of them in the near future by using tonnage oxygen. In this paper, the heat balance, control method of DXN and treatment of these dusts in reverberatory furnaces are described. DXN : Dioxin (The generic term of PCDD and PCDF)

Jan 1, 2000

By Tobias Dubberstein, Hans-Peter Heller

The viscosity of Fe-Cr-Mn-Ni TRIP/TWIP (Transformation Induced Plasticity, Twinning Induced Plasticity) steel with varied nickel content is investigated using a vibrating finger viscometer. The viscosity of the melt is calculated from the change in power input in the field coil by an immersed finger into the liquid steel to maintain a constant peak-to-peak amplitude of the sine wave of oscillator compared to the idle state. Nickel content in steel is varied from 3 wt% to 9 wt%. The dynamic viscosity (η) at 1600 °C for 3 wt% Ni is 3.73±0.14 mPas, for 6 wt% Ni 3.50±0.03 mPas, and for 9 wt% Ni 3.93±0.09 mPas. There is a kink from low to high nickel content in viscosity values of Fe-Cr-Mn-Ni alloys. This phenomenon can be explained by a change in coordination number in the melt, as reported for Fe-Ni binary system in literature. The availability of viscosity data delivers relevant input to model free fall atomization processes of FeCrMnNi alloys.

Jan 1, 2015

By V. M. Lsoitko

Statistical methods of technological mineralogy are used to model processing flowsheets in order to improve ore dressing efficiencies. The procedure involves determining geological and mineralogical characteristics of ores, classifying ore types and metallurgical procedures, and developing computer programs to interpret essential mineralogical parameters from on-stream analysis data. The on-stream analysis data include magnetism, radioactivity, luminescence and assays. The data are interpreted by computer and appropriate adjustments are made automatically in the plant.

Jan 1, 1989

By Alex Luyima, Honglan Shi, Lifeng Zhang, Yongqing Jiang

"Leaching process has been suggested to recover most metals from waste PWBs. In this study, the leaching behavior of most metals present in waste PWBs is evaluated before and thermal treatment. Different leaching acids: hydrochloric acid (HCl), nitric acid (HNO3) and aqua regia are compared. The effects of acid concentration, particle size of sample, leaching time and temperature are examined. Results revealed that most metals are present in small particle size and sequential leaching of PWBs with a combination of HCl acid and aqua regia is capable of dissolving most of the metals content of PWBs. Leaching of thermally treated PWBs produced the highest leaching percentages for similar leaching conditions.IntroductionApproximately 20–50 million tonnes of electronic waste (e-waste) is produced globally per year. Waste Electrical and Electronic Equipment (WEEE) or E-waste is one of the fastest growing waste streams in the world. In developed countries, it equals 1% of total solid waste on an average [1]. The growing stockpile of used and obsolete consumer electronics has been called the “largest toxic waste problem of the 21st century [2]. Printed wiring boards (PWBs) is an essential part of almost all WEEE, and accounts approximately 3% of all WEEE by weight [3]. PWBs are a platform upon which microelectronic components are mounted. PWBs contain metals (~40 wt. %), ceramics (~30 wt. %) and plastics (~30 wt. %) [4]. The metallic part includes; Cu, Pb, Zn, Fe, Cd, Be, Cr, Au, Pt, Pd, Ag, etc. The plastic part of the PWBs is mostly epoxy resins. These plastic resins also contain very toxic halogenated flame retardants (HFRs) [5]."

Jan 1, 2012

By Kun Wang, Xinhui Li, Huaqing Xie, Qingbo Yu, Qin Qin

"Three typical model compounds of bio-oil (ethanol, acetone and phenol) were studied in the steam reforming process for hydrogen production. In the thermodynamic analysis, the three componds showed the similar trends. The hydrogen yields increased with the increase of steam/carbon (S/C) ratios, and the temperatures of the maximum hydrogen yields moved afterward to low temperature zone. However, the hydrogen contents were just about 70%. For improving hydrogen yield, a new system for steam reforming of bio-oil with site CO2 capture was put forward. This system required the catalst with the larger granularity having greater mechanical strength and higher abrasion resistance. So, six Ni-base catalysts loaded on Al2O3 particles prepared were used and among them, Mg-Ni/Co catalyst showed the best catalytic performance. For the simulated bio-oil (the mixture of the compounds), the hydrogen yield can attain 63% with Mg-Ni/Co catalyst with the good stability and regeneration ability.IntroductionCurrently the interest in the use of hydrogen as a clean energy carrier is increasing, and the main way for producing hydrogen is steam reforming of fossil fuels, containing steam reforming of nature gas, naphtha and coal. But this way caused substantial amounts of CO2 emitted, and these sources of hydrogen which are non-renewable energy will eventually be used up [1, 2]. As a kind of renewable energy, biomass is recognized as an attractive alternative to fossil fuels, because of its neutral CO2 emissions [3]. There are mainly two thermochemical processes using biomass to produce hydrogen, gasification and flash pyrolysis followed by steam reforming (SR) of the biooil produced in the flash pryolysis process [4]. The latter was known as one of the most promising and economically viable methods for hydrogen production [5]. In the last decades, the biomass flash pyrolysis technology was adequately developed and fairly mature [6]. But the steam reforming of bio-oil is still at the research stage and yet has been leading to more and more concerns by the researchers. In their research, the catalysts were widely studied and yet mainly were powdery[7-10], and the reactors manily were fixed bed reactors[11-13], readly causing the carbon deposition and the catalyst deactivation, against the continuous running. In this paper, a new systerm was put forward and could realize continuous production of hydrogen, yet needed catalysts with the larger granularity having greater mechanical strength and higher abrasion resistance, as well as powdery CO2 sorbents which mainly calcium oxide based ones.In this paper, the thermodynamic analysis of the steam reforming processes of three typical bio-oil model compounds (ethanol, acetone, phenol) was performed, and the effect of S/C ratio and temperature on the hydrogen yield and the compositions of gaseous products were investigated. Then, a new systerm for steam reforming of bio-oil with site CO2 capture was put forward, and the catalysts with a certain granularity were prepared and studied."

Jan 1, 2014