Search Documents

By Arthur Miller, Andrew Weakley, Heather E. Lawson

"IntroductionDynamic failure events in an underground coal mine, or “bumps,” are defined as “the sudden, violent bursts of coal from a pillar or pillars or a block of coal, resulting in a section, the whole pillars, or the solid block of coal being thrown into an open entry” (Peng, 2008). Reports of disastrous and often fatal dynamic failure events date back over one hundred years in the United States. Mining practices and technologies have significantly evolved over the course of the last century, yet these events continue to occur. The events at Crandall Canyon, Utah (Gates et al., 2007) and Brody No. 1 Mine in West Virginia (Barker and McNeely, 2014) are two recent failure events that resulted in a total of eleven fatalities. These events testify to the fact that dynamic failure remains an imperative safety concern. Furthermore, their continued occurrences indicate that engineering controls have proven inadequate at wholly mitigating the problem.Multiple conditions have been associated with the occurrence of dynamic failure phenomena, including• thick, competent strata that can create a bridging effect, resulting in high abutment stresses (Rice, 1935; Holland and Thomas, 1954; Iannacchione and Zelanko, 1995; Agapito and Goodrich, 2000; Peng, 2008; Whyatt, 2008; Whyatt and Varley, 2010)• overburden thicknesses greater than 500–700 ft. (Rice, 1935; Peng, 2008)• a strong coal that is resistant to crushing (Rice, 1935; Peng,2008) or that is “uncleated or poorly cleated, strong…sustains high stress and tends to fail suddenly” (Agapito and Goodrich, 2000)• the presence of sandstone channels or rolls that can serve to concentrate stresses (Iannachione and Zelanko, 1995; Agapito and Goodrich, 2000)• fracturing of strong units above or below the coal seam (Whyatt and Varley, 2010)• slip along pre-existing discontinuities (Peperakis, 1958; Whyatt and Varley, 2010)• multiple seam mining interactions (Campoli, Kertis, and Goode, 1987; Iannachione and Zelanko, 1995; Newman, 2002; Peng, 2008)• mining sequences that can cause anomalously high stress concentrations (Campoli, Kertis, and Goode, 1987; Iannachione and Zelanko, 1995)"

Jan 1, 2015

By Mark Colwell

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a chain pillar design methodology readily usable by colliery staff. The project was primarily funded by the Australian Coal Association Research Program and further supported by several Australian longwall operations. The starting point or basis of the project was the Analysis of Longwall Pillar Stability (ALPS) methodology. ALPS was chosen because of its operational focus; it uses tailgate performance as the determining chain pillar design criterion rather than simply pillar stability. Furthermore, ALPS recognizes that several geotechnical and design factors, including (but not limited to) chain pillar stability, affect that performance. There are some geotechnical and mine layout differences between United States and Australian coalfields that required investigation and, therefore, calibration before the full benefits offered by the ALPS methodology could be realized in Australia. Ultimately, case history data were collected from 19 longwall mines representing approximately 60% of all Australian longwall operations. In addition, six monitoring sites incorporated an array of hydraulic stress cells to measure the change in vertical stress throughout the various phases of the longwall extraction cycle. The sites also incorporated extensometers to monitor roof and rib performance in response to the retreating longwall face. The study found strong relationships between the tailgate stability factor, the Coal Mine Roof Rating, and the installed level of primary support. The final outcome of the project is a chain pillar design methodology called Analysis of Longwall Tailgate Serviceability (ALTS). Guidelines for using ALTS are provided.

Jan 1, 1999

By Peter Cain

Twenty years of research into the design of permanent gateroad support (packs) in coal mines have resulted in two methods of pack design based on engineering principles. The first, the detached block concept, is based on static loading of the support system by an hypothetical detached block. The second, the roof beam tilt concept, is based on the dynamic loading of the support system as the roof beam tilts over the roadway about a pivot point located in the rib-side. The roof beam tilt concept has been used on a number of occasions to design packs in a variety of conditions. However, recent work in the Sydney Coalfield of Cape Breton Island, Nova Scotia, has shown that design criteria based on the roof beam tilt concept in its present state of development are far from universal in application. After a review of published pack performance data, including detailed studies conducted in the UK, France and Canada, it was found that consideration of the mechanical properties of the roof beam produced a design criterion that fitted the available data. Modifications to the design process using the roof beam tilt concept are suggested for use in pack design. The work also revealed that current research in other aspects of coal mine ground control, particularly the areas of powered support design and subsidence prediction, may provide valuable information leading to major advances in this field. Such developments could also extend the application of the roof beam tilt concept to the design of pillar systems.

Jan 1, 1993

By Yao Yuping

The strength and deformation of more than two hundred coal samples have been tested in the condition of triaxial compression. The regression equation showing the relationship between coal strength and pressure in the pores as well as confining pressure, was obtained. The appropriate calculation for stress-strain curve was carried out. Further, an analysis shows the variation of coal strength and its modulus of elasticity in methane medium.

Jan 1, 1992

By Saeed Zhandi, Behdeen Oraee

"Rock bursts remain an important problem in longwall coal mining. These bursts are due to a sudden and severe failure of rocks from a high stress concentration in deep underground excavations that occur with the instantaneous release of strain energy stored in the rocks. They can potentially cause irrecoverable damage to equipment and personnel, thus accurate rock burst prediction and control is expected to be carried out by the mine design engineer. As a result, this can constitute major challenges for said engineer. In this paper, forensic engineering has been used to evaluate the possibility and extent of rock bursts in deep coal mining. For this purpose, established mining engineering principles, including factors influencing the severity of rock bursts, have been incorporated in the forensic engineering technique. The analyses took place in five steps:• Assessment of regional and local conditions prior to the event• Assessment of conditions after the event• Hypothesize plausible ways in which pre-event conditions can become post-event ones• Search for evidence that either denies or supports various hypotheses• Apply engineering knowledge to relate the various facts and evidence into a cohesive scenario of how the event may have occurred.The paper concludes by demonstrating a method for predicting rock bursts and preventing their reoccurrence. The methodology used in this paper, together with the results obtained, can serve as useful tools for the coal mine design engineer in the primary evaluation of rock burst potential in underground coal mines.INTRODUCTIONA rock burst is defined as the sudden and great failure of rocks due to a high stress concentration in deep underground mines. This phenomenon occurs with the instantaneous release of strain energy that is stored in the rocks, and can cause irrecoverable damages to both equipment and personnel (see Figure 1). Rock bursts pose a hazard owing to their lake of predictability; in fact, research into understanding rock burst mechanics and implementing techniques for their monitoring and prediction has been taking place for over 50 years."

Jan 1, 2015

By A. Chrzanowski

The integrated approach to monitoring surveys is based on a simultaneous utilization of geodetic, photogrammetric and geotechnical measurements of displacements, tilts, strains and any other geometrical parameters of deformation. New techniques for the integrated surveys are being developed at the University of New Brunswick in cooperation with the Canada Centre for Mineral and Energy Technology. A telemetry system for continuous monitoring of geotechnical measurements under difficult climatic and topographic conditions has been constructed and successfully tested in a coal mining area in western Canada. A generalized method for analysing the integrated deformation measurements has been developed and applied in the test area to yield three dimensional empirical modelling of surface movements from geodetic, photogrammetric and tilt surveys. The most appropriate model can be chosen from a statistical assessment of several modelling possibilities. The empirical model of the deformation can be employed in a "calibration" of the prediction (deterministic) model of the ground movements. A computer programme for two- and three-dimensional finite element modelling of elasto-plastic deformations has been developed at UNB as a part of the integrated approach. The :EM has been tested in predicting deformation in the test area in difficult geological conditions which were associated with an extraction of a steeply inclined coal seam. The results gave good agreement with the actual displacements obtained from geodetic measurements and confirmed the existence of a suspected fault.

Jan 1, 1984

By Joao Felipe Costa, Jair C. Koppe, Andre Zingano, Cleber Gomes

"Run-of-mine Brazilian coal has high ash content and low calorific power. Therefore, the coal must be washed to achieve the power plant specifications for burning coal. A large amount of waste results from the coal preparation, and it must be disposed of in waste piles or waste dams, depending on the material size. These waste disposals are the cause of serious environmental problems, not only in the short and medium terms, but mainly in the long term, due to the risk of provoking acid drainage or spontaneous combustion. Waste disposal requirements also demand large areas. Other problems include the pillar and roof stability in abandoned and mined out areas, building of edifices on the old and active mines, and mining under urban areas. To solve these problems simultaneously, backfilling the entries in mined out areas began with two objectives: to understand the mechanical behavior of the filling material and to model the backfilling of room-and-pillar coal mine entries through numerical simulation. Laboratory tests were performed for different filling material (with and without cement) to determine its mechanical properties and failure criteria. Based on this study, it was possible to conclude that the backfill method is a good strategy to improve the ground stability in room-and-pillar coal mines for the long term, especially for weak coal seams, and to reduce the quantity of material on waste piles on the surface.INTRODUCTIONRun-of-mine (ROM) Brazilian coal has high ash content and low calorific power. Therefore, the coal must be washed to achieve the power plant specifications for burning coal. Two types of waste are associated with power plants that bum coal for energy generation: 1) the waste from the coal preparation plant and 2) the ash from the power plant after coal burning.The Brazilian coal ash content in the ROM coal is between 45 and 55%. The clean coal is 20 to 30% ash for 4,500 kcal/kg (18,000 BTU). The coal preparation plant recovery is only about 35%. Santa Catarina State (SC) produces about 7 million tons/year of ROM coal, which results in a total of 4.5 million tons of waste. This is a large amount of waste that must be disposed of in waste piles or waste dams, depending on the material size. The waste and ash content is represented by silicate materials, such as clay and sand, and by sulfide materials, like pyrite and organic sulfur (between 1and5%)."

Jan 1, 2010

By Thomas Barczak

Longwall shields provide essential ground control in Iongwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of¬the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (I ) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield's capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.

Jan 1, 2002

By H. N. Maleki

Tension-torque relationships were investigated *n a coal mine for bath standard 5/8 in. (16 mm) bolts and a vibrating wire instrumented bolt, using conventional and controlled installation techniques. The instrumented bolts differed from the standard bolts by their head size and hole preparation procedures. The controlled installation technique developed by the U. S. Bureau of Nines (USBN) involved using hardened washers and lubrication in the bolt assembly, and maintaining a minimum thrust level during bolt installations. The object of this study was to determine the tension to torque ratio (lb/ft-lbs; for standard bolts and instrumented bolts for both conventional and controlled installation techniques, and to modify the bolt assembly so that the ratios would be equal for the instrumented and standard bolts for both installation techniques. It was shown that the instrumented bolts installed in faced holes had a similar tension torque ratio td that of standard 5/8 in. (16 mm) bolts installed in unfaced holes for each installation technique, and thus they were representative of other uninstrumentea bolts. This was achieved by evaluating the influence of several factors oh the relationship, including: facing the hale surface, introducing washers and lubrication in the bolt assembly, and applying different levels of thrust at installation due to bolter operator practice. The tension to torque ratio fur conventional bolts was only 21 (lb/ft-lb) for the coal mine, resulting in an installation tension of 4000 lbs (17.8 kg) with the typical installation torque of 150 to 400 ft-lb. This tension level was approximately 50 percent of the required bolt tension, and thus, it was concluded that torque standards are not sufficient to assure adequate bolt tension. .he low tension levels were due to the particular wait hardware in use, operator practice, and bolt fencing.

Jan 1, 1984

By Saeed Zandi, Kazem Oraee

"Tunnels and galleries are the most important structures in coal mines. They are used for variety of purposes, such as transporting ore and people and for ventilation. A well-designed support system is necessary to stabilize structures and prevent collapse.Using rock bolts increases the strength of the rock in which tunnels are made. Rock bolts are used extensively in most underground mines today, and coal mines are no exception. Almost all galleries in a typical coal mine use some type of rock bolt, at least, as a means of partial or supplementary support.In this research, changing the support system from expensive methods to the use of rock bolts as the primary means of support is discussed, with the focus on a particular gallery in Hejdak coal mine. Visionary design methods, in conjunction with rock mass classification schedules, were used to determine an optimal rock bolt pattern. For this purpose, rock mass rating (RlVIR) and quality index (Q) classification systems were used. Several empirical methods were also used to design an optimal pattern for rock bolt installation in the particular tunnel under analysis.As such, the tunnel support system was designed using both finite element and empirical methods. Finally, the results obtained from both numerical and empirical methods were compared under different load conditions. The methodology prescribed in this paper, together with the comparison, can be a useful tool when selecting a support system. The results can also be used to design a support system in this and any other coal mine with similar conditions.INTRODUCTIONSince the advent of underground excavation techniques, one of the biggest challenges has been stabilizing tunnel walls and preventing roof collapse in tunnels and other underground openings, such as galleries. Loose rocks and layers drop into tunnels and galleries, except in very hard rock. Underground roof collapse and falling rocks can have devastating effects on the safety of operation personnel and equipment and can seriously affect production. When designing an underground coal mine, the stability of tunnels and galleries is an important parameter that should be studied carefully because it has an important role in the production process of the mine. Therefore, an appropriate and well-designed support system is necessary for preventing collapse and helping to stabilize the tunnels and galleries."

Jan 1, 2016

By Yanfa Gao

Abstract In order to control and reduce ground subsidence due to coal mining, and to protect building, railway and other surface construction, a new subsidence control method is proposed. Ground subsidence is reduced by grouting bed separations in overlying strata with fine-coal ash. Engineering application tests have been performed for 5 years in Tangshan Coal Mine. Kailuan Group Corporation. China. The technology has been applied to 4 fully mechanized sublevel caving mining faces. Its effect in reducing subsidence has been significant. The technology including grouting engineering design method and ground subsidence prediction theory is introduced in detail. Keywords: overlying strata separation, multi-layer grouting, subsidence control

Jan 1, 2002

By David P. Conover, Jake Bain, Christopher M. Ross

"Highwall mining of thick (up to 100 ft) steeply dipping (20° or more) coal seams provides many challenges, both geotechnically and operationally because seam dips near or in excess of highwall mining machine capabilities are encountered. Maximizing coal recovery while maintaining highwall stability requires innovative techniques with regard to web and barrier pillar layout, depth of penetration, and choice of mining horizon within the seam. Stability of highwall mining slopes, openings, and pillars are typically analyzed using the ARMPS-HWM program, as well as LAMODEL, UDEC, and Slope-W modeling. Highwall stability can be maintained and highwall mining production optimized by applying design criteria in creative ways, including alternating miner penetration depths and initiating mining of thick seams toward the bottom of the seam. Highwall mining of thick, steeply dipping coal requires careful planning and execution, including close cooperation between geotechnical design engineers, the mining company, and the highwall mining contractor. This paper describes the application of creative design techniques to a specific pit arrangement at the Westmoreland Kemmerer Mine, Kemmerer, Wyoming. Highwall mining was accomplished by UGM ADDCAR Systems, LLC, on a contract basis. INTRODUCTION Highwall mining is a technique for attaining additional coal recovery after the economic strip limit is reached in surface mining. It involves remote deployment of a continuous miner in openings beneath the final highwall, with no personnel entry. Many candidate areas for highwall mining have thick and steeply dipping seams. Mining downdip presents challenges related to the maximum pulling capacity of the machine, traction of the cutting head, and material conveying, all of which limit penetration depth. Maximum penetration is greater for flatter slopes and decreases for slopes nearing the threshold of the maximum machine operating angle. Most highwall mining operations are relatively flat with slight undulations within the seam; therefore, the highwall mining pillar design criteria applies fairly equally to the entire mining area. However, in steeply dipping deposits, design criteria based on higher overburden loads at the far end of the penetration are excessively conservative for the shallower portions of the openings near the highwall."

Jan 1, 2017

By Rudrajit Mitra, Tien Dung Le, Chengguo Zhang, Bruce Hebblewhite, Joung Oh

"Geomechanical and geotechnical characteristics of coal seam are important parameters that directly affect the cavability of top coal in the longwall top-coal caving (LTCC) method. The impact of these parameters such as coal strength, coal deformation modulus, coal discontinuities and top-coal thickness on cavability has not been fully understood in previous numerical analyses. The limitation and selection of the numerical modelling codes were two of the main reasons. In this paper, detailed caving simulations are performed using a 2D distinct element method (DEM) code, UDEC, to study the effect of various critical parameters on top-coal cavability. The numerical analysis evidently shows that the coal deformation modulus, coal discontinuities, and top-coal thickness have considerable influences on cavability. Coal strength is also a factor but to a lesser extent. The results presented in this paper contribute to the understanding of top-coal cavability in different mining environments and facilitate the development of an advanced cavability evaluation criterion. INTRODUCTION The longwall top-coal caving (LTCC) method was originally developed in the 1950s in the former Soviet Union and France (Tien, 1998). The method was nearly abandoned in Europe after the mid-1980s; however, it has been significantly improved and widely applied in China since the late 1980s. A conceptual model of the LTCC method is shown in Figure 1 in which a thick coal seam is divided into two sections including the lower or cutting section, and the upper or top coal section. The lower section of coal seam is mined by conventional longwall method. Meanwhile, the upper section is recovered by caving through the face support. The LTCC method is considered to be the most viable option for mining general thick seams. Compared to the multi-slice longwall (MSL) method, LTCC has the major advantages (Zhongming, 2001; cited by Vakili, 2009):"

Jan 1, 2017

By Vince Caggiano

The newly developed Hilti OneStep roof bolt combines the standard 5-step anchoring process (i.e. drilling, transfer of drill steel, insertion of resin, insertion of rod and tightening) into one easy operation. It also replaces 4 items (drill head and steel, adhesive cartridge and anchor) for simplified material management. This paper describes its history of development, and bolt, bolt drilling and bolt resin specifications, experimental test results in Germany where it achieved a reduction of 36-42% in roof bolt cycle time and 25-30% improvement in gateroad development rate. In the U.S. coal mines, a time study showed that OneStep can save approximately 50 seconds in installation time per bolt.

Jan 1, 2005

By Peter Zhang

"Room-and-pillar mining with pillar recovery has historically been associated with more than 25% of all ground-fall fatalities in the underground coal mines of the United States. The risk of ground falls during pillar recovery increases in multiple-seam mining conditions. The hazards associated with pillar recovery in multiple-seam mining include roof cutters, roof falls, rib rolls, coal outbursts, and floor heave. When pillar recovery is planned in multiple seams, it is critical to properly design the mining sequence and panel layout to minimize potential seam interaction. This paper addresses geotechnical considerations for concurrent pillar recovery in two coal seams with 70 ft of interburden under about 1,000 ft of depth of cover.The study finds that, for interburden thickness of 70 ft, the multiple seam mining influence zone in the lower seam is directly under the barrier pillar within about 100 ft from the gob edge of the upper seam. The peak stress in the interburden transfers down at an angle of approximately 20° away from the gob, and the entries and crosscuts in the influence zone are subjected to elevated stress during development and retreat. The study also suggests that, for full pillar recovery in close distance multiple seam scenarios, it is optimal to superimpose the gobs in both seams, but it is not necessary to superimpose the pillars. If the entries and / or crosscuts in the lower seam are developed outside the gob line of the upper seam, additional roof and rib support needs to be considered to account for the elevated stress in the multiple seam influence zone. INTRODUCTION Room-and-pillar mining accounted for about 40% of underground coal production in the United States in 2016. Pillar recovery, practiced in about one-third of the room-and-pillar mines, represents about 10% of the coal mined underground, yet it has historically been associated with more than 25% of all ground fall fatalities (Mark, Chase, and Pappas, 2003). In some U.S. coal fields, particularly central Appalachia, many coal mines are operating under geological conditions with multiple coal seams. The risk of ground falls during pillar recovery increases under multiple-seam mining conditions. The hazards of pillar recovery associated with multiple-seam mining include roof cutters, roof falls, rib rolls, coal outbursts, and floor heave (Mark and Tuchman, 2007; NIOSH, 2010b). Pillar retreating creates abutment pressure, not only in the currently mined seam, but also in the overlying or underlying seams. Multiple-seam interactions become more pronounced as overburden depth increases and interburden thickness decreases. To safely recover the pillars in multiple seams, it is critical to properly plan the mining sequence and panel layout to minimize potential multiple-seam interaction."

Jan 1, 2017

By William B. Beerbower

When full length resin grouted bolts were introduced into U. S. coal mines some 11 years ago, it was assumed that safety would be the primary benefit. There is ample testimony to substantiate the safety factor as an important reason for using resin roof bolts. More recently, it has been determined that many coal operators not only concur with the safety consideration but also benefit economically from the safer working conditions resulting from a reduction in roof falls. IMPROVED SAFETY Some typical roof fall reduction experiences with resin bolting follow: ? Western Kentucky Mine - Resin bolting reduced roof falls by 80%. ? Southern West Virginia Mine - Experienced 141 roof falls between 1971 and 1972. In 1973 with resin bolting, roof falls were reduced 85%. ? Western Pennsylvania Mine - In 1973 had 59 roof falls with mechanical bolts. During the same period of 1974 with resin, only 19 falls were experienced - a reduction of 66%. The overall experience with resin bolted roof support has been an average 50% reduction in roof falls. Long term, this can translate into improved worker morale. As a matter of fact, a general mine foreman at the same Southern West Virginia mine mentioned above commented that improved miner morale was noticeable following the introduction of resin bolting. HOW GREATER SAFETY CAN BE COMBINED WITH INCREASED PRODUCTIVITY IN COAL MINING OPERATIONS Experience has also shown that a reduction of roof falls with resin bolting has resulted in increased production for many coal operators. Some typical examples with mines using resin bolting follow: ? Western Kentucky Mine - Resin bolting contributed to increasing production from 7000 to 11,000 tons per day, due to a 80% reduction in roof falls. This was accomplished in part by a reduction of 50% in timbering requirements and the reassignment of three roof fall cleanup crews to coal production. ? Pennsylvania Mine - Following resin bolting introduction the section showed a 50% increase in production. ? Central West Virginia Mine - Continuous miner production averaged 6 cuts per unit shift prior to resin bolting. Reduction of cleanup time, resulting from improved roof support with resin bolting, increased production to an average of 9 cuts per unit shift. PROPERTIES OF RESIN BOLTING SYSTEMS Several of the important properties of resin bolting systems which contribute to its improved performance are listed below: ? Full length anchored resin bolts and many resin anchored, point anchored bolts provide effective resistance to changing rock strata stresses throughout their length, thereby improving stabilization of rock strata over long periods of time. ? Individual layers of rock are anchored into a single high strength beam providing excellent resistance to vertical and lateral strata movement, the most common cause of roof failure. ? Moisture cannot corrode the fully grouted bolt. ? Has twice the pull strength of mechanical bolts (See Figure 1)

Jan 1, 1982

By Gift Makusha

Surface subsidence associated with coal mining activities in the Mpumalanga Province of South Africa changes the natural environment in several ways, and current challenges for mining companies include rehabilitation of the natural environment and the prevention of further degradation. To monitor the spatial and temporal evolution of surface subsidence, traditional fieldbased monitoring approaches such as GPS and spirit leveling are employed at a number of locations. However, the resulting measurements are point-based, and frequent revisitations are necessary to map the evolution of surface subsidence basins over time. To address these limitations, differential interferograms derived from repeat-pass satellite-borne synthetic aperture radar (SAR) systems were tested for their ability to measure and monitor surface deformation. The SAR data was captured by the European ERS-1 and ERS-2 satellite and covered a timeframe between 2008- 09-15 and 2008-09-15. The resulting interferograms revealed several features indicative of surface subsidence. Ground truth data confirmed the presence of a subsidence basin, detected using differential interferometry techniques during the 35-day period between April 12, 2008 and May 17, 2008; a maximum vertical deformation of 3.2 cm (1.3 in) was recorded. Interferometric monitoring revealed an eastward migration of the subsidence basin between June 2, 2008 and September 15, 2008 with an additional 4.7 cm (1.9 in) of subsidence observed. This migration coincides with the advance of the working face of the mine during this period. Finite element modeling will be performed in order to model the rates and evolution of surface subsidence haloes as underground mining advances. These presented results demonstrate the ability of interferometric synthetic aperture radar techniques to measure surface subsidence as well as the monitoring of the evolution of subsidence basins over time. This implies that the technique could be included, together with traditional field-based surveying techniques, in an operational monitoring system. With knowledge on deformation rates and subsidence basin evolution, informed decisions on current and future infrastructure development can be made and remedial actions and prevention strategies can be formulated for the problems associated with environmental degradation.

Jan 1, 2011

By Radoslaw L. Michalowski

The operation of mobile mining equipment near the crest of stockpiles and wastedumps often results in localized slope failures. The Bureau of Mines has developed a computer code based on a rigorous limit plasticity approach which determines the admissible total weight for a concentrated loading near the crest of these otherwise stable structures. The program is based on a three- dimensional analysis and provides an upper bound solution to the load that can be applied to the top of the operating distances for mobile equipment from the slope edge. This presentation will discuss the application of limit plasticity to the development of the local three-dimensional collapse mechanism, and the use of the computer code based on this approach for mining applications.

Jan 1, 1990

By Thomas W. McClain

This paper describes the importance of considering ground control measures when importing U.S. continuous mining technology in foreign countries. Important ground control factors are discussed. Each year the USA exports a significant amount of continuous miner equipment (i.e. continuous miners, roof bolters, coal haulers, shuttle cars, continuous haulages, scoops and feeder-breakers). International customers see the opportunity to significantly improve their productivity and increase their longwall gateroad development rates by implementing the room-and-pillar (place changing) mining systems used throughout the USA. However, a number of issues are often overlooked or not thoroughly evaluated when selecting the equipment, often resulting in lower than expected productivity. Ground control is one of the critical factors that must be addressed. Since 1993, the author has assisted numerous international customers and manufacturers with implementing or improving the performance of continuous miner and room-and-pillar systems in Australia, India, Mexico, South Africa, and the United Kingdom. An essential first step is to conduct a thorough ground control study, and then integrate its findings into mine layout, equipment selection and section operating plans. Based on actual case histories, the author will present a number of examples and "Do's and Don'ts." Another key to success is the involvement of manufacturers and suppliers with customers when implementing new systems and technology. The importance of allowing for cultural evolution by both management and workers for acceptance and successful implementation of any new system is also discussed. Over the past ten years, the global coal industry has gone through some very dramatic changes. Countries that previously experienced a freight advantage, such as Australia shipping coal to Japan and Korea versus the United States, are finding they are now in a world coal market similar to other commodities and products. Today, coal prices arc stated F.O.B. at the consumer, and the origin is often irrelevant. Also, previously state-run coal industries have been privatized, such as the United Kingdom, and others such as Poland and India are currently going through the same transition from state-run to the private sector. In all cases, the key to continued viability, or survival, depends largely on reducing costs in order to compete for a market share. Two ways exist to reduce costs. First, almost everyone tries to reduce expenditures. Depending on the circumstances at a given mine or in a specific country, this helps to some point. However, most find that secondly, production must be increased to achieve the necessary cost reductions to compete in today's global coal market. As a result, over the past ten years, foreign companies and countries have looked to the USA for new mining methods and systems to significantly increase productivity. Thus, a major portion of American equipment manufacturers and suppliers sales have been exports, which has played a major role in helping to "keep-the-doors-open" for a number of companies through the lean 1990's, when American coal companies were postponing capital expenditures and expansions. As foreign companies and countries have looked to the USA for ways to improve productivity, they have become particularly interested in continuous miner equipment systems and most often "room-and-pillar," "bord-and-pillar" or "place changing" mining systems for four reasons. First, in countries such as the United Kingdom and Germany, who have been longwall mining for generations, there remain numerous remnant small pockets of reserves in existing mines that are either too small or too difficult to longwall mine, and are conducive to the flexibility of continuous miner systems. Second, for countries such as Australia, who have experienced the constant problem of developing longwall gateroads in a timely manner to avoid longwall move delays, new or alternate methods are required. Third, companies and countries using roadheader machines on coal production are recognizing the increased productivity potential of continuous miner equipment. Fourth, countries such as South Africa and India, where a substantial amount of the production comes from conventional mining methods, "drill-and-blast", companies are recognizing the opportunity to improve by implementing continuous miner technology. Colliers & Associates, Inc. has found that over the past eight years too often foreign companies or countries purchase American continuous miner equipment without first conducting a thorough geologic, geotechnical and ground control study for the reserves to be mined. The problems are compounded by not developing mine plans, and submitting them to the regulatory authorities for approval prior to purchasing and even implementing the equipment.

Jan 1, 2001

By William Kendall

INTRODUCTION Stillwater Mining Company, with its two underground, hard rock mines in South Central Montana, is the largest primary producer of palladium and platinum in the Western Hemisphere. Platinum Group Metals (PGMs) are mined from a specific zone within the Stillwater Complex, a layered mafic/ultramafic igneous intrusion, named as the J-M Reef. Over much of the J-M Reef, the economically minable, mineralized horizon is contained at typical horizontal widths of 6.5 ft to 8 ft wide. This feature of narrow mining widths has made it challenging to safely and effectively mine these areas of the J-M Reef using mechanized cut and fill and sublevel sill development mining methods. Mechanization of most or all of the steps of the mining process is important to Stillwater in the continuous pursuit of high standards in safety and health. Mechanized bolting within the J-M Reef ore production headings is an important piece of reaching these objectives. In general, metal/non-metal mining requires varied mining techniques, as compared to more traditional bedded mineral/resource deposits. Narrow vein mining is a selective mining technique that generates a minimal amount of waste material while obtaining the more valuable ore deposits. Drilling and bolting in narrow vein mining has traditionally been performed with air-powered, hand-held ?jackleg? equipment because mechanized equipment is, typically, too large for the selective narrow vein techniques. In addition, traditional hand-held pneumatic equipment provides significant flexibility for small-opening, narrow-vein developments, reducing waste rock handling and improving ore recovery management. The hand-held equipment is also relatively inexpensive to purchase. Due to its simplicity, it is also relatively easy to train operators to use hand-held equipment. Hand-held equipment has been routinely used to safely install ground support and to develop production faces in hard rock mines for many years. Although it is effective, the hand-held equipment requires operator exposure to certain inherent hazardous conditions in the active face/development mine areas. These include falling rock, tripping hazards, bending/twisting/lifting hazards, high noise levels, and chemical fumes from the hammer exhaust. Based on health and safety statistics from the Stillwater mines, operation of the rotary-percussive hand-held equipment adversely affects the long-term health of the operator?continual jackleg operation frequently results in long term damage to hearing, shoulders, arm and wrist joints, and back injuries. This reduces the quality of life for the operator and also results in higher personnel turnover rates for the mining company.

Jan 1, 2014