Search Documents

Coal mass strength properties must be estimated to obtain realistic estimates of coal pillar strength. The limitations of existing techniques for approximating these properties are discussed. The coal mass is anisotropic. The Hoek and Brown approach to rock mass property estimation is modified to allow for this. This approach requires the Rock Mass Rating (RMR) for the strata. In the normal case where bedding is sub-horizontal, these major planes of weakness have little effect on the strength of pillars. As a result of this the RMR must be measured parallel to bedding. This means that a significantly higher rating than that usually obtained for coal is observed. The use of mass strength property estimates in extant empirical relationships is outlined. At high width to height ratios, an acceleration in the rate of increase in pillar strength with increasing width to height ratio has been observed. The empirical relationship developed by Salamon (the so called squat pillar formula) takes account of this. This relationship was found to have significant limitations with respect to its universal application. Modifications arc made to Bieniawski's empirical formula to extend its use to large width to height ratio (squat) pillars. This new squat pillar formula has none of the disadvantages associated with Salamon's relationship. Strain softening was incorporated into non-linear finite difference numerical modelling to estimate pillar strengths. The technique outlined above is used to obtain peak coal mass properties. Modelled pillar strength was found to be sensitive to both peak and post peak mass strength properties. Post peak properties were found to be difficult to obtain and required some back analysis. Modelling results were used to estimate both the strength of squat pillars and parameters for use in a now squat pillar empirical strength relationship.

Jan 1, 1992

By Larry Howe

Second, or retreat mhng with Mobile Roof Supports (MRS) has now been part of coal mining in the United States for a decade Their utilization has evolved into mining applications which vary in seam heights from 38 inches to 170 inches, and overburden depths from outcrop to beyond 1200 feet This paper will detail the pillaring plans, lift sequences, and mnchky utilized in these operations and the rational for the plans A comparison of the current productivities achieved will be outlined

Jan 1, 1998

By Ulrich Langosch

In the 1990s the German mining industry introduced a new generation of shield supports. The new design of support has a maximum load capacity of 10,000 kN, making these units as strong as the shields used in Australia and in the USA. DMT took more than 3,100 underground observations in order to verify the roof fall frequency by statistical analysis. The results of this work have led to practical recommendations for roof control and the required shield support system on longwall faces. The underground observations have been correlated to Rock Mass Classification, to stress calculations and to the angle between the direction of the fissures and the direction of longwall mining_ The analysis work yielded the following two sets of results: 1. There is a critical distance between the canopy tip and the coal face (Tip to Face TF,n,). The TF,n, is predictable and relates to: the thickness of the first roof layer and its uniaxial compressive strength. The face support should have a TF that is less than the TFcrtt in every underground longwall situation. Exceeding the TF crit call immediately result in a roof fall. 2. Using the obtained regression equation DMT is able to calculate the probability of the roof fall frequency (FF), which describes the roof fall sensitivity. When TFcr;, is exceeded the predicted roof fall FF relates to: the measured support resistance (MSR) of the shield support the calculated vertical stress (p?) the fissure-direction index (DI = angle between main fissure direction and direction of mining) and the distance by which TFcrit is exceeded (ATF). Armed with these results DMT is now able to predict the critical distance between the tip of the canopy and the coal face (TFcrit), as well as the roof fall frequency, for all shield designs. By applying the new calculation method it is now possible to compare alternative longwall layouts and different shield support types under pre-set geological conditions. Mining engineers on site are therefore in a position to make the necessary roof control preparations required to run the longwall operation to maximum efficiency. The results provide a useful basis for making practical recommendations and for selecting the most effective design of shield support. The paper uses practical examples to demonstrate the R&D results and present the various methods now available for calculation and prediction in longwall roof control.

Jan 1, 2003

By Eric Westman

Ground control problems caused by multiple-seam interaction frequently sterilize coal reserves. Interaction mechanisms differ for overmining and undermining and are controlled by mining, spatial. and geologic conditions at each site. A multiple-seam interaction analysis software program, UGLY (Uppersearn Gateroad Longwall Stability), has been used to evaluate sterilization of coal reserves due to overmining at three locations. Four case histories were reviewed to determine the effectiveness of improved ground control in mitigating interaction effects.

Jan 1, 1997

By Thomas M. Barczak

The decade of the 90's brought an unprecedented increase in the development of innovative technologies to provide more effective and easier to install roof support in underground mines. To facilitate the application of these technologies to improve mine safety. National Institute for Occupational Safety and Health (NIOSH) developed the Support Technology Optimization Program (STOP). STOP is a windows based software program that provides mine operators with a simple and practical tool to make engineering decisions regarding the selection and placement strategy of these various standing roof support technologies. This program includes a complete data base of the support characteristics and loading profiles obtained through safety performance testing of these supports at the NIOSH Safety Structures Testing Laboratory. Support design criteria in the form of the required support load density at a specified convergence can he established from four options: ( 1 ) a data base of measured ground reaction data from various mines or ground behavior information inputted by the user. (2) determination of loading requirements based on a detached roof block or rock failure height. or (3) criteria based on the current roof support system, and (4) arbitrary criteria set the by user. Using these design criteria, the program will determine the installation requirements for a particular support technology that will provide the necessary support load density and convergence control. Optimization routines are also available to determine the most efficient support design for a user specified support installation- In addition to these performance measures. STOP can be used to compare material handling requirements and installation costs. Comparisons among the various support technologies are easily made including graphical analysis of relevant support parameters. This paper describes the STOP and its application to optimize standing secondary roof support systems.

Jan 1, 2000

By Lorraine Kent

Mine tunnel support using rockbolts was introduced in UK coal mines over the period 1987- 1992 and is now used in over 70% of all mine tunnels. In every case the reinforcement design has been based on the observational approach. After the initial reinforcement design has been established appropriate action levels are defined for predetermined amounts of movement indicating the onset of instability. If the action levels are exceeded appropriate remedial action is taken usually in the form of additional support or reinforcement to maintain stability. This paper outlines the observational design method as used in UK coal mine tunnels. It discusses the low cost instrumentation which has been developed to monitor roof deformation, dual height telltales, how action levels are defined based on the geotechnical environment and the types of remedial measures typically taken. An alternative approach for dealing with areas of increased deformation involves reacting to early roof movement trends and modifying the support installed at the face of the development accordingly. Installation of additional support at the face of the heading improves ground control in poor geotechnical conditions and has the advantage of potentially reducing later additional support costs. A case study is described to illustrate how 'early' action levels can be incorporated into a roof support plan enabling a flexible roof support strategy. Such a system will be site specific and continued analysis of monitored information will be required to confirm the action levels or to adjust them according to any change in geotechnical environment. More accurate roof deformation monitoring systems, such as the Remote Reading Telltale system recently developed by Rock Mechanics Technology Ltd. (RMT) and currently undergoing Mines Safety and Health Administration (MSHA) approval, are ideally suited to this application. The Remote Reading Telltale system provides accurate mine wide monitoring of roof condition on a surface PC.

Jan 1, 1999

By C. Babcock

This Bureau of Mines report considers some equations for mine pillar design from 1833 to the present. Most of the equations are of essentially the same kind, using pillar width to height relationships. The effects of end constraint and test volume size, that were implied in some of these early equations have received special emphasis in recent years. Experimental testing in the laboratory throughout the period given has been on prisms or cubes of coal or rock. Most of the present concepts have been known since about 1912. Wilson has recently emphasized the effect of end constraint in his confined core concept, but a number of other earlier relationships have indicated an awareness of the effects of constraint as well.

Jan 1, 1981

By L. Z. Wojno

Tunnels in South African gold mines are developed at depths down to 3 600 m below surface where the virgin rock stress approaches 100 MPa and, on occasions, through rock where the field stresses exceed 150 MPa. In addition, many tunnels are subjected to increases in field stress of over 50 MPa during their useful lifetime. As a consequence, the walls of most tunnels are fractured causing the rock to dilate into the tunnel. Quantitative data on the extent of this fractured zone are presented. The function of support in these circumstances is to reinforce and maintain the integrity of the fractured rock. In 80 per cent of the 800 km of tunnels developed annually, the support methods used are capable of maintaining the stability of the tunnels. However, the remaining 20 per cent of tunnels is subjected to severer conditions where dilation in excess of 250 mm occurs and/or where the probability of strong seismic ground motion is high. In these tunnels, additional support is required. The type and pattern of support for both normal and severe conditions is described. In spite of the improved support used, damage to tunnels may occur. To minimize this damage, the concept of a rock reinforcing tendon that will yield and do work, when subjected to quasi-static or rapid deformation, has been put forward. Specifications for such a tendon are presented and the development of certain yielding tendons are described.

Jan 1, 1987

By J. R. Koehler

The failure of yield pillar-based gate mad designs to provide adequate ground control performance is primarily related to the use of "critically" sized chain pillars. A "critical" pillar is one that falls into a range of pillar sizes that are too large to either yield nonviolently or yield before the roof and floor sustain permanent damage, but are too small to support full longwall abutment loads. To directly compare the in-mine performance of critical and yielding pillar designs, the U.S. Bureau of Mines recently completed a field study in a tapering gate road at the Sunnyside No. 1 Mine, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m-wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m-wide design more closely approaches proper yield pillar dimensions. Probehole drilling of several 10.6-m-wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset. suggesting a properly functioning yield pillar design.

Jan 1, 1995

By Larry Stolarczyk

A clear vision of the future coal mining industry was developed into a hierarchy of technology needs by the National Mining Association (NMA) and the Chief Executive Officers of the mining industry. Although improvements in safety and environmental factors were the main drivers in the technology roadmapping workshop sponsored by the Department of Energy, the agile mining machine of the future must efficiently extract coal from deeper, thinner, and more geologically complex coal beds. One of the challenges will be to develop sensors and software that enable clean coal cutting in a changing geologic environment. The roadmap identifies imaging ahead of raining and horizon control within the top ten needed technologies. For these technologies to be adopted by the mining industry, they must be proven to be effective while driving down mining cost and risk. This paper describes how three-dimensional imaging ahead of mining and horizon sensors enable improved ground control and safety in the mining of underground coal.

Jan 1, 2003

By Ross Seedsman

Discussion on the design of roof support in tailgates has often been conducted without a clear statement of the stress and failure conditions acting. There is general agreement that in the tailgate the vertical stresses above the chain pillar increase. Within the stress 'bulb' associated with this vertical stress increase there will be an increase in horizontal stress. This does not mean that the horizontal stresses acting across the roof line increase. In retreat longwalling, the proximity of the tailgate to the adjacent goof results in a substantial reduction in the horizontal stress field acting in the immediate roof. Furthermore, at the face/tailgate corner the onset of significant compression of the chain pillar. if it is designed to yield, will result in a further reduction in the horizontal stresses in the immediate roof. It is suggested that this latter mechanism can cause the horizontal stresses in the immediate roof to go to zero. Whatever, the horizontal stress acting across the roof in the face/tailgate corner will be significantly lower than in the face/maingate corner. The implication of the model is that support design in tailgates should be based on the assumption of zero horizontal (in fact tensile) stresses. How the roof behaves in a tensile stress environment is a function of joint spacing and orientation compared to excavation width and direction. It is speculated that the empirical relationship between support density and roof rating results from the relationship between joint spacing and bedding spacing. The onset of stress reductions has major implications to the design of cable and bolt anchorages in the tailgate environment.

Jan 1, 2001

By Timothy Ross

The Pittsburg & Midway Coal Mining Co.'s Kemmerer Mine is one of the deepest surface coal operations in the world, with the highwall extending to approximately 1,000 ft above the pit floor. To increase recovery, auger mining is being evaluated beneath the highwalls of several seams representing the current economic limit of pit development. The primary augered seam is over 50 ft thick, can approach 100 ft thick, and dips into the highwall at an average of 17 degrees. The seam thickness and dip present many geotechnical design and operational challenges for multiple Sup to five) lift augering. This paper presents the design criteria and methodology applied to determine appropriate web and septum thicknesses for the various cover depths anticipated, as well as operational measures that can be taken to increase overall coal recovery. The primary tool used in the design was the finite difference code FLAG. Models incorporating typical strata sequences associated with the coal seam were run at several different cover depths corresponding to the maximum anticipated auger penetration. Web and septum thicknesses were varied until the minimum thickness satisfying a given safety factor criterion was determined. Using this procedure, design curves were developed for web and septum thickness versus cover depth. Operationally, several recommendations were developed to ensure that overall coal recovery is maximized. By angering across the scam dip, auger penetration per hole can he increased dramatically, and by carefully planning maximum planned auger penetration versus hole spacing, increased coal recovery can be safely attained.

Jan 1, 1999

By R. D. Lama

The concept of rigid or yielding bolts is discussed based upon support requirements for excavations of equivalent geomechanical behaviour. The concept of equivalent geomechanical behaviour is introduced for comparison purpose where the rock mass properties are varied for a given depth (stress) so that the deformation of the roof without any support remains constant = 300mm. A simple experimental theoretical analysis for a uniform stress field acting on an axi-symmetric excavation is conducted to establish roof bolt requirements under different conditions such as width of a given excavation, time of setting of support etc. Results are presented in graphical forms.

Jan 1, 1992

By John Stankus

Seam interaction in multiple seam mining has significant effect on entry stability. The remaining pillar in an old working usually creates a high stress concentration zone while the gob creates a stress release zone. A good panel layout should take advantage of the stress release effect created by old workings. This paper presents two case studies of multiple seam mining. The Jennmar Finite Element Analysis System (JFEA) is utilized to analyze the seam interaction effect and identify the mess concentration and relief zones Panel layouts are designed bad on the results of the finite element analysis Appropriate roof support system are also designed for different seam interaction areas.

Jan 1, 1999

By Frank E. Chase

Geologic structures have been responsible for numerous underground accidents and fatalities, and are a constant-source of down time. During - longwall mining, ground control problems associated with geologic anomalies are aggravated by the abutment pressures which develop as the panel is retreated. Therefore, it is imperative that these structures be recognized and properly supported in head- and tailgates. Fractures, faults, clay veins, igneous dikes, and ancient stream channels (paleochannels) disrupt the lateral continuity of the mine roof and can cause falls in gateroads. Horsebacks and kettle bottoms are also hazardous because abutment pressures tend to "pop out' these structures into the gateroads. This Bureau of Mines investigation describes the physical characteristics associated with hazardous geologic structures, identifies the coal fields where-they have been observed, and, where possible, suggests support strategies and other mine plan modifications to help minimize their effect.

Jan 1, 1990

By Jialin Xu

Bed separations position, size, development characteristics and their influence factors have been analyzed in-depth by experimental and theoretical methods. The results show that the key strata determine the creation, development and space-time distribution of the overburden bed separations and fractures. Based on the dynamic growth principle during the two-stage development of bed separations, the theory of section-grouting for the overburden bed separation space and the O-ring theory for the pressure-relieved methane drainage are proposed. The technique has been applied in some coal mines in China to reduce surface subsidence and for methane drainage. Keywords: rock strata movements; key stratum; bed separation; bed separation grouting; pressure-relieved methane drainage

Jan 1, 2003

By I. L. Follington

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.1 Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production, Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required. A mechanism has been postulated for the deformation behaviour of the roof and pillars in a mechanised pillar extraction operation from the continuously monitored data, observational data and results of previous studies. The 7 m wide fenders were observed to yield under abutment stresses before lifting commenced. The stability of these fenders throughout the lifting sequence was considered to be dependant upon the magnitude of their post peak load carrying capability. This is influenced by the post peak stiffness and the extent of roof lowering in the vicinity of the fender. Difficulties with fender extraction occurred where remnant coal left standing in the goaf caused uncaved goat to bridge to the mined fender. Difficulties were also experienced where sub-vertical jointing occurred in the roof of the split reducing it's ability to bridge effectively. Despite the relatively short monitoring period, the potential role and application of continuous monitoring in advancing understanding of the rock mass response to mechanised pillar extraction operations has been demonstrated. This understanding now requires enhancement and shows great potential for aiding the optimisation of mechanised pillar extraction operations.

Jan 1, 1992

By D. W. H. Su

Following a roof fall in the B12 headgate of a CONSOL Pennsylvania Coal Company (CCPC) underground coal mine in February 1998, CONSOL R&D and Exploration initiated an underground roof geology reconnaissance program along the B13 and B14 developments to define potential roof instability areas and to recommend appropriate supplemental headgate support. This reconnaissance program revealed the presence of a thick, massive Pittsburgh sandstone channel overlying the B13 and B14 panels. Surface and underground core holes confirmed the close proximity and the very massive, nonlaminated nature of the sandstone. To mitigate anticipated adverse conditions at the B 13 and B 14 longwall faces due to delayed caving of the massive sandstone behind the shields, a task force consisting of Operations, Exploration, and R&D personnel was formed in May 1998. Several operational adjustments were made by mine management, including repairing damaged lemniscate links, maintaining immediate forward shield support, and implementing measures recommended by the task force intended to boost the shield set load density at the face. After reviewing available geotcchnical information, the task force also recommended fracing of the massive sandstone over the B13 and B14 panels to enhance caving characteristics and further reduce the bending-induced stresses in the sandstone near the face. Horizontal fracs were created at a horizon about 25 feet above the Pittsburgh seam main bench over the two panels in June and November 1998, respectively. To evaluate the effect of sandstone fracing and operational adjustments on the bending-induced stresses in the sandstone, three finite element models were constructed and analyzed. Results from the finite element analyses indicate that one horizontal frac, 25 feet above the Pittsburgh seam, would reduce the bending-induced stresses in the sandstone by approximately 50 percent, maintaining them at a level below the ultimate strength of the sandstone. Operational adjustments to increase the support set load density and support stiffness could reduce the bending-induced stresses in the sandstone by a maximum of an additional 10 percent. Shield pressure monitoring at the B14 midface confirmed the presence of a lower roof pressure zone inby and outby the 1314 frac holes. This lower face pressure significantly contributed to improving the B13 and B14 longwall productivity and safety. The total production downtime due to bad top at the B 12 face within the interval of channel influence was 30,600 minutes compared to about 3,500 minutes each for the B13 and B14 faces. The average longwall advance per machine shift for the B13 and B14 faces within the channel was about 70 percent higher than that for the B 12 face.

Jan 1, 2001

By Hui Chen

The paper describes the use of a physical model technique to investigate the failure modes of mine tunnels with reference to the in situ stress field. The characteristics of stratification commonly encountered within UK coal mining conditions have been taken into consideration. The investigation has indicated that the weak floor strata in coal mining tunnels, under the action of high rock stresses, will be subject to the floor lift problem in both predominantly horizontal and vertical stress fields. However, the failure mode and mechanism varies between the two stress field patterns. In the predominantly horizontal stress field, the tunnel floor tends to fail by gradual bending of the laminations, whilst in the predominantly vertical stress field, the floor tends to fail by a shearing action with the failed material lifting in the form of a block. The failure mechanism is discussed with reference to mechanics theory.

Jan 1, 1993

By C. D. Peters

The Bureau of Mines has been researching remote sensing analysis of an underground coal mining area in Utah and computer-aided methods of defining ground control hazards in this mining area. As a result of these studies, a preliminary potential hazards map was developed for the test site. This map is based primarily upon a lineament (linear feature) analysis of Landsat satellite data. Other data used were paleochannel location data, resistivity data, and information from surface and underground field checking of the lineaments and ground control problems in the mine. Lineaments proved to be reliable indicators of hazardous areas, although the type and degree of hazard varies with different lineament trends and the presence of other conditions such as lineament intersections and intersections with other geologic structures or with paleochannels. Lineaments were observed to match faults, joints, and/or joint trends in the area. The paleochannel data, derived from drill hole data, provided basic information about potentially hazardous areas in the mine by suggesting where paleochannels could cause instability in the roof rock. The ground control problem data served largely to define the relative degree of hazard associated with lineaments and the types of hazards encountered in the mine. Resistivity data helped confirm the presence of fractures where they were expected to occur both from surface geology and from the lineament data.

Jan 1, 1986