Search Documents

By Christopher Mark

The Bureau of Mines is conducting research to assess the effectiveness of different chain pillar designs in maintaining gate entry stability. The study described in this paper was performed in a 1200 ft long, experimental headgate section which contained three pillar designs: - a three-entry, yield-abutment pillar' system, - a four-entry, yield-yield-abutment pillar system, and - a five-entry, all-yield pillar system. As the longwall mined by the experimental section, Bureau engineers monitored entry convergence, roof sag, and changes in roof quality. The results of the study indicate that the all-yield system performed at least as well as, and probably better than, the two abutment pillar systems.

Jan 1, 1988

By Madan M. Singh

Currently longwall coal mining operations require at least 3 entries on both the headgate and tailgate ends because of ventilation and safety requirements. Driving of entries, however, is a slow and costly process. Often it is a bottleneck in longwall development. Single entry gateroads are permitted in Europe and commonly used there. This study entailed ascertaining the feasibility of using a single entry in the United States, without sacrificing safety. This design was conducted for an operating longwall mine in the Black Warrior coalfield in Alabama, An understanding of rock loads and consequent support requirements is prerequisite to the design and successful demonstration of the single entry system. Efforts in this regard were directed at determining center (packwall) support requirements for various single entry widths. Critical to the analysis is knowledge of the nature and extent of side abutment stresses. In collecting geological and geotechnical information relating to the stability of the single entry, Engineers International, Inc. engaged in the following: ? Examination and inspection of the single entry demonstration at the Sunnyside Mine in Utah. Severe ground conditions and unacceptable levels of entry closure were experienced there prior to the tailgate phase. Observations at the mine presented a clear perspective on possible ground control problems for future single entry designs. ? Reconnaissance inspection and classification of roof rock conditions. ? Detailed mapping of roof structure in the areas to be instrumented. ? Installation of convergence stations in the longwall headgate to monitor roof movement during mining. ? Measurement of side abutment stresses in a yield pillar in the area of the convergence measurements. ? Measurements of coal fracture distribution by the detail area method. ? Rock properties determinations of roof, coal, and floor rocks; samples obtained by core drilling. ? Determination of floor bearing capacity by in-situ testing.

Jan 1, 1982

By Richard C. Repsher

The U.S. Bureau of Mines has developed a method and device designed to detect lose rock material in underground mines. The technology is designed to be an aid to mine workers in detecting hazardous roof conditions in underground mines which can complement or replace the traditional roof sounding techniques where the miner relies on experience to determine whether rock conditions are sound. The leading cause of accidents and fatalities in underground mines is falls of lose rock pieces or rock slabs from the mine roof. The device is an electronic roof sounding device that acoustically determines the integrity of mine rock. In previous research the Bureau of Mines found that loose rock, when impacted, vibrates at a much lower frequency than intact rock material. A major problem in determining rock stability using this technique has been the repeatability of the matt signal. This difficulty baa been greatly reduced in the current design by measuring the power spectra contained in two separate frequency bands of the signal produced by striking the rock in question. The ratio of the energy contained in each band is computed. This process minimizes any striking force differences, producing accurate, repeatable results for solid rock as well as loose, drummy material. The prototype has been successfully- tested in a variety of underground environments including coal, uranium, molybdenum, silver and salt. The technology has been investigated by the U.S. Mine Health and Safety Administration and the Department of Energy for use in detecting detached tunnel lining areas in nuclear repositories. The paper will discuss the technique, applicable results, and future applications.

Jan 1, 1990

By D. L. Price

This paper presents a method of measuring field power consumption of shearers and deriving specific energy consumption versus shearer haulage speed performance curves. A description of a computer program which simulates the cutting action of a shearer drum is presented. A comparison between the field specific energy curves and the computer simulation results is made. The simulation results compare well with the field data where all the coal seam is being cut by the shearer. The computer simulation results give hack-calculated field pick force cutting characteristics, which allow the performance of the shearer to be predicted for other operating conditions, e.g. effect of changes to pick lacing, effect of changing the drum rotational speed, allows the calculation of power requirements for a particular production rate.

Jan 1, 1992

By Syd S. Peng

A total of 209 cases of subsidence data over longwall panels in 16 US coal seems have been collected and built into a subsidence database. The database is developed under MS Windows environment. It uses a very user-friendly menu driven system. The empirical formulae for a number of commonly used subsidence parameters have been derived from those collected subsidence data.

Jan 1, 1995

By Danny J. Van Roosendaal

An investigation was undertaken to determine hydrogeological effects of subsidence over a longwall coal mine in the Illinois Basin. At this mine, approximately 200 ft of bedrock overburden is overlain by up to 150 ft of glacial till and localized water-bearing glacial sediments within a buried bedrock valley that overlies the longwall panel. A finite-element mechanical model of the subsided longwall panel shows sufficient strain to enhance permeability throughout the bedrock portion of the overburden. However, examination of the actual surface subsidence profile indicates that the overburden deformation is localized in narrow zones at the panel edges. The aquifer units at the base of the glacial sediments are confined by glacial clays (above) and weathered shales (below). Elevated water levels were observed in the glacial aquifers during subsidence, which indicates that the clays and shales maintained confinement as the overburden subsided and deformed. A three-dimensional ground-water flow model was used to simulate the effects of subsidence on the hydrogeologic system and to estimate inflows into the mine. Longwall retreat was simulated by several model runs, each representing a new longwall face position. Simulated heads and mine inflows were calibrated with recorded water levels and observed inflow conditions by modifying the hydraulic conductivity of particular model layers. Model calibration indicates that the permeability of certain lithologies, such as plastic underclays and weathered shales, is not significantly enhanced by subsidence. A worst-case scenario was simulated by inserting a deeply incised, sandfilled valley into the model, which had only minimal impact on the simulated mine inflows.

Jan 1, 1995

By David K. Ingram

The objective of this U.S. Bureau of Mines (USBM) investigation was to characterize overburden response due to longwall mining. Subsurface strata and surface deformations were monitored at two sites in southeastern Ohio. Site A included two adjacent longwall panels. Site B consisted of one longwall panel. Both sites had similar mine geometries and overburden thicknesses. The major difference between the two sites was the rock strata within the overburden. Multipoint borehole extensometers (MPBX) were employed to measure subsurface displacements. Survey monuments were installed above the centerline and profile of each panel to measure surface deformations. Subsidence of the surface was observed before and after movement was detected in the MPBX units. Initial and final displacement of the MPBX units occurred at the same time at both sites. No deformation was detected outside the panel area. The development of overburden deformation was different over each panel. The final subsurface failure characteristics also varied between panels.

Jan 1, 1994

By J. Nielen van der Merwe

During the process of pillar extraction at the Welgedacht Colliery, an unexpected pillar collapse resulted in the entrapment of equipment. The area was visited soon after the event to evaluate the stability of the area for the purposes of extracting the equipment. It was found that the area had stabilised sufficiently to allow work without undue risk to the safety of workers. The equipment was reclaimed successfully. A subsequent investigation into the reasons for the collapse was conducted. It entailed detailed underground and surface subsidence observations and numerical modeling. It was found that none of the perceived negative factors that were present at the time could result in pillar loads that were sufficient to cause the collapse. It was concluded that the local pillar strengths were less than the nationally used value and that they were possibly further reduced by aging.

Jan 1, 1999

By S. J. Jung

The goal of this research is to demonstrate how optimization methodology can be coupled with the finite element method for greater stability of underground mine openings. As a result of increasing mining depth and intersection of geologic discontinuities, mining environments are becoming more complex. Current design procedures are rapidly becoming inadequate. In this research, the finite element method has been coupled with optimization criteria to design more stable and safe underground openings

Jan 1, 1993

By Nicholas P. Kripakov

The unpredictable massive collapse of roof in openings developed under apparently safe and stable roof conditions in coal mines of the United States has been of much concern for many years. One type of massive caving phenomenon is often attributed to cutter roof, a failure that initiates at one and/or both upper corners of an entry and propagates nearly vertically resulting in overall failure with little or no warning. This paper reviews current methods being used to control cutter roof and suggests new alternatives. The impact of basic parameters that include mine geometry, overburden geology, rock properties, and in situ stress conditions is discussed in the context of their relationship to this problem. The effects of various stress control measures are investigated with model analysis to gain insight into means of reducing the high level of stress known to exist at the entry corners of a West Virginia coal mine prone to cutter roof. The results are presented in the paper and the feasibility of their practical implementation is discussed.

Jan 1, 1982

By Michael Karmis

During the last 25 years, technological advancement and subsidence research have resulted in more accurate and diverse prediction capabilities. The work presented in this paper focuses on the development of integrated prediction capabilities for dynamic deformation indices and for strains over sloping terrain. In order to assist subsidence engineers with accurate prediction methodologies, the research also addresses the development and validation of techniques that can enable model calibration using alternative measured subsidence parameters such as horizontal or ground strain instead of the traditional vertical subsidence values. This paper presents the basic concepts and validation of the above mentioned enhanced prediction and control methodologies, which are necessary for effective assessment and control of mining-induced subsidence, using examples and case studies. In addition, a risk assessment approach for evaluating landscape stability over mined areas is presented. The enhanced prediction methodologies have been incorporated into the Surface Deformation Prediction Software (SDPS) package.

Jan 1, 2008

By Jamal Hematian

Understanding the behaviour of rocks in a high horizontal stress field, such as that in Australia, is critical when analysing the stability of underground structures. This paper addresses the significance of the post-failure behaviour of rocks on the stability of underground structures which are under the influence of a high horizontal stress field. The research work was conducted through a combination of numerical modelling, laboratory testing and field investigation. A number of 2-D FE model of roadways were constructed based on the data obtained from laboratory testing and field investigations. The models were then analysed using three different solution techniques; simple linear-elastic, non-linear elastic-plastic and elastic-plastic with consideration of post-failure behaviour (softening model). Results indicated that the post-failure behaviour of rocks significantly influence the stress and displacement patterns around the roadway. The stress and displacement patterns as well as the extent of the yield zone around the roadway predicted by the softening model were in good agreement with that from the field study. Based on the results of the study, an appropriate support system has been suggested to govern the stability of roadways.

Jan 1, 1994

By Kenneth Rigsby

Black Mountain Resources' Highlands Mine No. I is a full extraction room and pillar operation located in Harlan County, Kentucky. Black Mountain extracts the 0.9 to 1.1 meter (36- to 42-inch) thick Owl Scam that is situated 60 to 70 meters (200 to 235 ft) above the longwall panels of the abandoned Arch No. 37 Mine, in the 3.4 meter (I I ft) thick Harlan Scam. In the areas where full extraction has taken place, the overburden above the Owl Seam ranges from 60 to 430 meters (200 to 1,400 ft). A short room and pillar panel was developed above an extracted longwall panel to test the selected pillar size, to evaluate support systems, and to verify the shape of the subsidence profile over the recovery end of the depleted longwall panel. It is over the recovery end that Highlands Mine No. I would access the Owl Seam reserves that exist above the No. 37 Mine. Black Mountain selected pillars sizes to be employed above the longwalls based on the ability to fully extract a pillar employing extended cuts. After a mechanical testing program was completed and mine behavior and top disturbance were observed in the test panel, John T. Boyd Company (BOYD) verified pillar stability and designed support systems. BOYD previously designed No. 37 Mine's gate pillars and studied subsidence and gob formation over its longwall panels; this effort aided the analysis of overburden movement and pillar integrity at Highlands Mine No. 1.

Jan 1, 2003

By James Pile

The San Juan Coal Mine, located near Farmington, New Mexico, supplies the San Juan Generating Station with more than 6 million tons of coal annually. To replace dwindling surface mine production, San Juan installed a longwall in 2002. The roof rock in much of the underground reserve consists of interbedded coals, carbonaceous shales, and mudstones. Roof support consists of fully-grouted roof bolts, both tensioned and non-tensioned, supplemented by modified cable trusses. Short-encapsulation pull tests conducted by San Juan's geotechnical engineering department showed that some of the immediate roof layers provided variable bolt anchorage. To ensure that the roof bolts were obtaining the necessary anchorage, additional tests were conducted in a variety of locations. The results have been used to determine the optimum support design for different areas of the mine. Another series of tests evaluated the performance of several bolt and hole diameter combinations. The experience at San Juan Mine shows that short-encapsulation pull tests can provide the information necessary to improve ground control in variable roof conditions. It also illustrates how a pro¬active geotechnical engineering program can be an essential component of a state of the art underground coal mine.

Jan 1, 2003

By Richard G. Burdick

The Bureau of Mines', Denver Research Center has been conducting research for the past few years on the use of resistivity methods to locate abandoned mine workings. As this work has progressed, it is apparent that in some cases, in addition to detecting the old workings; stoping, precursive to surface subsidence has also been detected. This paper describes the Automated Resistivity method and discusses sites in Colorado. Wyoming. and Illinois where the subsidence phenomenon has been observed.

Jan 1, 1982

By William D. Gallant

This paper presents the results of a joint cooperative research project between the CANMET Cape Breton Coal Research Laboratory and the Cape Breton Development Corporation to observe the subsidence profile over the stopline of 2 West panel, Phalen Mine. A novel technique was designed and Implemented to determine vertical displacements of the overlying strata from within a near horizontal borehole drilled over the 2 West panel. Restrictions on data collection techniques due to the submarine nature of the coalfield are discussed. Development and implementation of the borehole technique using a piezometer and inclinometer Is described. Performance of the instruments and profiles obtained by them are presented and compared. Recommendations for design improvements are made to Improve the efficiency of the technique.

Jan 1, 1990

By Wen H. Su

Multiple seam mining and its associated problems are very serious in Southern West Virginia where poor planning or lack of knowledge in seam interaction often results in complete loss of coal properties. Several measures have been proposed to alleviate the interaction prob¬lems under various multiple seam conditions, but few of them are spec¬ific in terms of mining plan. Two parallel approaches are adopted for this paper. One is field investigation which consists mainly of mine site visits and gathering of data. The other is the two-dimensional finite element simulation of mine workings using the data gathered as input. Two typical cases which represent the past and present multi¬ple seam mining practice in West Virginia were investigated. Much attention is focused on the interaction problems experienced and the important parameters controlling interaction. Several key parameters controlling interaction in multiple seam mining were analyzed. Proper mining plans, by which the interaction problems can be minimized, are proposed for the individual cases after a better understanding of the interaction mechanism was realized through finite element analyses.

Jan 1, 1984

By Clarence O. Babcock

Since Vicat in 1833, the width to height ratio of a mine pillar has been taken as the fundamental variable in pillar design. From work in the laboratory by many investigators testing rock, Coal and concrete samples, it has been concluded by some that pillars with a width to height ratio of 10 to 1 are indestructible. It has also been concluded that a constrained core exists within the pillar which increases the pillar strength. The role of the roof and floor, if mentioned at all, is often noted in an incidental way. In the present work on laboratory testing of model pillars on concrete, coal, and rock instrumented with special strain gages, it was concluded that the end constraint and not the width to height ratio is the significant variable in determining the pillar strength. In tests where the end constraint is steel, a large compressive stress is produced on the horizontal plane of the pillar, and this effect increases as the width to height ratio is increased, resulting in an increase in pillar strength. If the end constraint is not steel but something with a small Young's modulus, the state of stress in the horizontal plane may be tensile, increasing as the width to height ratio increases, resulting in a decrease in pillar strength. Related to mining, the results are that a large width to height ratio pillar is strong for strong roof and floor and weak for weak roof and floor. That is, the roof and floor and not the width to height ratio determine the pillar strength. The confined core condition should be verified by testing if large pillars are to be used. If there is no confined core or the pillar is in tension, smaller pillar sizes should be used. The final conclusion is that the geometry alone is meaningless in pillar design.

Jan 1, 1984

By Bruce H. Gardner

This paper describes the application procedure of the Stress Control mine design method. This procedure has evolved over the past 20 years of the practice of this Method in trona, potash, salt, and, most recently, in coal mining. The Stress Control Method of mine design has been defined and amply described in previously-published work (1,2,4) -- likewise, the associated system of in situ instrumentation (3,4) and the computer modelling technique (2,3,4) which are the principal tools of this method. The present paper defines the procedure by which the in situ instrumentation and computer modelling cools are combined in adapting the general concepts of Stress Control to produce site-specific design solutions. This procedure is illustrated by means of case examples from three mines. The Stress Control Method utilizes the geometry of underground excavations, particularly through the time sequence of the creation of yielding pillars, to control stresses. The time sequence is devised such that all the primary stress envelopes are transformed into a single secondary stress envelope, surrounding the group of rooms separated by the yielding pillars. The secondary stress envelope provides protection to the roof and floor boundaries from all the external stresses. This stress relief effect removes the cause of roof and floor failure -- high shear stress in the weakly confined boundaries of underground openings. It thereby replaces artificial support with ground self-support, enabling simultaneous in¬creases in stability and percent recovery. Within limits which are still being explored and extended, the Stress Control Method has proven capable of overcoming the trade-off between stability and extraction ratio which has afflicted conventional mining methods. The application procedure of the Stress Control Method is outlined below in terms of the objectives, structure, and stages of a generic mine rock mechanics program for the site-specific adaptation of the time control yield pillar design technique.

Jan 1, 1984

By David A. Newman

Severe roof control problems have plagued a West Virginia underground mine since its initial development in the late 1970's. Adverse roof conditions in the Eastern portion of the reserve result from a combination of mining: - perpendicular to the major principal horizontal stress direction, - near lineament intersections, - in areas where the ratio of horizontal stress to vertical stress exceeds 2.00 to 4.00, and - where laminated strata are present in the immediate roof. The focus of this study is to identify the engineering (mine orientation, roof safety factor) and geological parameters (lineament and horizontal stress orientation, horizontal to vertical stress ratio, and immediate roof lithology) causing poor roof conditions and to quantify their influence on projected mining conditions in the Western portion of the reserve Rose diagrams were used to illustrate the correlation between the orientation of eight hundred thirty-six (836) roof falls with that of forty-four (44) lineaments and the principal horizontal stress Similarly a composite map was used to demonstrate the relationship between roof falls and the ratio of horizontal stress to vertical stress The immediate roof strata across the property were categorized as either laminated or non-laminated based upon a thorough examination of one hundred sixty-two core logs. The presence or absence of fireclay, a rider coal, and carbonaceous shale was also noted because of the historic correlation with poor roof conditions. Rock strength and physical property tests were conducted on selected immediate roof strata recovered from coreholes drilled along the mains projected to the Western portion of the reserve Potential roof control problems in the Western reserve were quantified based upon the correlations developed by analyzing engineering and geological data The main conclusion is that laminated roof strata, the rider seam, and its associated fireclay will have the greatest influence on mining conditions. Roof problems attributable to horizontal stresses will not be as severe in the West due to an increase in overburden depth and corresponding decrease in the stress ratio. Recommendations are provided for mining orientation, the layout of mains and submains, panel location, and roof support based on intended service life.

Jan 1, 1999