Search Documents

By D. Minney

The quality of resin used in South African collieries is currently controlled according to South African Bureau of Standards, "SABS-1534:2002". It has however been found that resin which passed the SABS tests failed in underground short encapsulation pull tests. An investigation was therefore conducted to determine the characteristics of resins that are currently being used in collieries. A series of in situ short encapsulated pull tests was conducted to determine the effect of expired resin on support performance. The results showed that the longer the time after the expiry date the poorer the resin performance. A series of resin-torque tests has been performed using Anglo Coal's testing facility. The following parameters were investigated on different resins: Spinning speed, Mixing time, and Setting time. An attempt was also made to develop a new quality control procedure for resin. This procedure enables mining personnel to make sure that the quality of resin can provide the required support performance. The effect of spinning speed on resin performance was also investigated. The results showed the resin gelling times of resin decreases as the spinning speed increases. It is found that over-spinning with slow speed roofbolters may result in decreased bond strengths. It was found that a 30-second resin (10-second spin, 30-second hold) should never be spun more than 20 seconds, even with very slow roofbolters (100 rpm).

Jan 1, 2005

By Daniel W. H. Su

Underground roof geology reconnaissance is being conducted by CONSOL Inc. to enhance mine productivity. Often, roof instability within mine entries is the consequence of highly variable geology that cannot always be detected from information provided by widely-spaced surface core holes. Utilizing a combination of roof drilling data, geophysical logs, and borehole camera and fiberscope observations, roof geology mapping is conducted within longwall development entries in areas of specific concern prior to commencement of longwall mining, Depending on the uniformity of the site-specific roof geology, data point spacing along the longwall development generally ranges from one to five crosscuts. Surface core hole data are correlated with the roof geology mapped underground to validate the underground observations. Detailed roof geology maps can then be produced to enable ground control engineers and mine management to select cost-effective ground control techniques. However, this procedure is not necessary or useful in all situations and it is employed only when there is strong geologic evidence to justify a closer inspection.

Jan 1, 1999

By Gennaro Marino

Documented case histories are studied where data were found on the initial collapse of the overburden above the longwall panels. Under this scenario, the most controlled conditions exist for assessing the span capacity of the overburden (i.e., before failure the roof spans to fin coal abutments on two to all four sides). In an attempt to correlate theory to field observations, data are used on the overburden lithology, and the depth, width, and face advance of the panel, as well as, the subsidence conditions noted on the surface. The subsidence measured on the surface is used to determine when complete failure in the over- burden rock has occurred.

Jan 1, 1987

By David Dye

Good morning, everyone, and thanks Syd for that fine introduction. I am honored to be here to help you celebrate 25 years of advancement and success in the important field of ground control. I would also like to recognize Dr. Peng for his significant contributions in longwall mining and ground control. His contributions have had a major impact on improving safety and reducing fatalities in America?s mines. Thank you, Dr. Peng, for the important work you have carried on throughout the years. Many miners are alive today because of your dedicated work to protect them.

Jan 1, 2007

By Christopher Mark

"Many problems in rock mechanics are limited by our imperfect knowledge of the material properties and failure mechanics of rock masses. Mining problems are somewhat unique, however, in that plenty of real world experience is generally available and can be turned into valuable experimental data. Every pillar that is developed, or stope that is mined, represents a full-scale test of a rock mechanics design. By harvesting these data, and then using the appropriate statistical techniques to interpret them, mining engineers have developed powerful design techniques that are widely used around the world. Successful empirical methods are readily accepted because they are simple, transparent, practical, and firmly tethered to reality.The author has been intimately associated with empirical design for his entire career. But where his past papers have described the application of individual techniques to specific problems, the focus of this paper is the process used to develop a successful empirical method. A six-stage process is described:1. Identification of the problem, and of the end users of the final product2. Development of a conceptual rock mechanics model, and identification of the key parameters in that model3. Identification of measures for each of the key parameters, and the development of new measures (such as rating scales) where necessary4. Data sources and data collection5. Statistical analysis6. Packaging of the final productEach of these stages has its own potential rewards and pitfalls, which will be illustrated by incidents from the author’s own experience. The ultimate goal of this paper is to provide a new and deeper appreciation for empirical techniques, as well as some guidelines and opportunities for future developers."

Jan 1, 2015

By Marc Arl

Failures of the face and roof above longwall shields have caused days and sometimes weeks of lost production. A common recovery method for these failures has been to pump light weight cementitious grout into the roof and face cavity to stabilize the area This approach while effective is very time consuming and costly. Mines in several coal producing nations have over the past few years been applying phenolic foam grouts in these situations in lieu of cementitious materials. Phenolic foam is a two-component injection product intended for cavity filling, air and gas sealing and the consolidation of highly fractured strata. The properties of phenolic foam; rapid application, quick setting, high expansion rate, high compressive strength and excellent anti-static properties, produce a fast, safe and cost effective cavity filing solution. The product is also classified as fire resistant and so is also suitable for sealing off underground heatings and for aiding fire fighting operations in deep mines. This paper will discuss the application and use of phenolic foam in various underground coal mines in the world over the past few years.

Jan 1, 2005

By J. B. Lizak

This paper is not available for inclusion in the Proceedings at the time of printing, but it will be included as an insert.

Jan 1, 1984

By Jin He

Based on the simple-beam theory, a stress analysis model was established for undermining in multiple seam strip-pillar mining when the strip pillars were not columnized; the effects of various mining factors (e.g., mining depth, inter-burden thickness, recovery ratio, etc.) on inter-burden stability were analyzed; the changes in inter-burden stress distribution were investigated; and the important role that the inter-burden spacing and the mining width of the lower seams on inter-burden stability was studied. Finally, the actual practice used in Feng Feng Mine area was used as an example to demonstrate the rational mining width for a fixed mining depth.

Jan 1, 2006

By Freddie Hunter

An underground mining method for extracting an eight metre (26') coal horizon, containing a sandstone layer. A decrease in the thickness of the rock strata between the number two and number three seams of the Sasolburg Coal Field, has resulted in a total mining horizon approximately eight metres (26') thick. This parting varies in thickness and competency and in some areas is impractical to cut with a continuous miner. In addition, the general mining area is highly jointed. The top seam is first mined to a normal bord and pillar plan with a continuous miner. The bottom seam is then mined by selectively undercutting the stone parting constituting the floor of the top seam. In areas where this parting is between 0.75 - 2.50 metres (29.5" - 98") thick, it is suspended from the primary roof support installed when mining the top seam. Secondary, high extraction retreat mining is then undertaken in the coal pillars adjacent to the suspension supported headings in the bottom seam. Left in-situ, the parting provides lateral support to the pillar sidewalls in both the top and bottom seams, enabling high percentage extraction rates in what was previously thought an uneconomically mineable area. The paper proposed, presents the challenges and practical implications of executing the mining method, including the primary roof control of the top seam and the stone parting between scams.

Jan 1, 2003

By Jun Lu, Mark Van Dyke, Daniel W. H. Su, Greg Hasenfus

"This paper presents the geologic and ground control challenges that were encountered by CONSOL Energy’s mining operations in southwestern Pennsylvania. A sandstone-to-limestone geology transition was encountered by Mine A, where the primary 8-foot bolts were anchored in claystone. Upon experiencing roof sags and a roof fall in the return entry, 6-foot high-tension, fully-grouted primary bolts were employed along with 16-foot center cable bolts at every other strap to improve beam building and to ensure proper anchorage into the competent limestone. No longwall delay was reported within this geologic transition zone, although there was some difficulty in maintaining an open #2 entry airway behind the longwall face.The geologic encounter in Mine B was more complex, where fluvial deposits of massive sandstone channels, shale channels and pyritic-rich, green claystones were encountered on both sides of the mains, and which impacted both development and longwall ground control. In particular, poor transitional roof areas near the edges of the sandstone and shale channels often posed significant ground control challenges. In addition, hydraulic fracturing was sometimes utilized to enhance caving of massive sandstone behind the shields to relieve pressure at the face. Longwall face conditions and advance rates were documented to illustrate the effects of sandstone channels, shale channels, and green claystones on safety and productivity and to demonstrate the effectiveness of the hydraulic fracturing.Shale channels, slickensided zones, laminated roof zones, soft floor, and a regional syncline were encountered in Mine C, the combination of which posed unique ground control challenges during both development and longwall mining. The presence of soft floor, coupled with the presence of thick floor coal and deep cover, resulted in headgate convergence during retreat of the first right-hand longwall panel. Two-piece 8-foot bolts were sometimes observed to fail at the coupler within the laminated roof zone, and 6-foot, 1-piece, fully-grouted point-anchor bolts were employed as the primary bolts thereafter."

Jan 1, 2015

By Daniel W. H. Su

Current longwall pillar design relies heavily upon past experience and many assumptions about pillar and entry response to longwall abutment pressures. Caving characteristics of the immediate and main roof strata are known to play an important role in the overall pressure redistribution, which determines the maximum abutment pressure, abutment pressure at the T-junction, and the width of influence zone. This paper presents the results of an extensive geomechanical study in a longwall panel at a West Virginia coal mine. The response of eight headgate pillars and the adjacent entries was monitored as the longwall face approached and passed by the instrumented locations. Overburden response to longwall mining was also monitored, and height of the highly fractured zone above the gob was determined by postmining drilling. Good agreement was observed between the measured stress changes and those computed using the known height of the highly fractured zone. The results provide a detailed picture of the response of overburden strata and chain pillars to longwall mining.

Jan 1, 1987

Large-scale shear apparatus is designed to investigate the shear hehaviour of simulated soft rock joints under constant normal stifmess condition. Regular saw-teeth profiles having inclinations between 9.5" and 26.5" have been tested. The strength envelope based on these test results indicates that predictions made by Panon (1966) are accurate for the lower asperity angles. However, for higher asperity angles, Patton's model overestimates the shear strength especially in the low to medium normal stress range. In contrast, while Barton's model (1973) is realistic for Constant Normal Load (CNL) condition, it seems to be inappropriate for modelling the shear behaviour of soft joints under Constant Normal Stiffness (CNS) condition. An empirical strength envelope for the prediction of peak shear strength of joints is proposed in this study to account for the change in normal stress and surface degradation during CNS shearing.

Jan 1, 1997

By Ihsan Berk Tulu, Keith A. Heasley, Chris Mark

"The Analysis of Retreat l\.fining Pillar Stability (ARJ\1PS) and the Lal\.fodel programs have been used successfully in the U.S. for designing safe pillar recovery operations for many years. However, the recent Crandall Canyon l\.fine collapse showed that further research is required to improve the pillar design for recovery under deep cover. To this end, the National Institute for Occupational Safety and Health (NIOSH) and the West Virginia University (WVU) l\.fining Engineering Department have been working together to improve both the ARJ\1PS and the Lal\.fodel programs.This paper compares and analyzes the overburden loads calculated by ARJ\1PS 2002, the new ARJ\1PS 2010, and the Lal\.fodel program with regard to the retreat pillar line, the gob, and the barrier pillars. The analysis shows a number of distinct differences between the ARJ\1PS and Lal\.fodel loading distributions. Ultimately, the programs, with their distinctive load distributions, are used to analyze a database of 52 deep cover pillar retreat case studies, and the ability of each program to discriminate between successful and unsuccessful retreat pillar plans is evaluated.INTRODUCTIONThe Analysis of Retreat l\.fining Pillar Stability (ARJ\.f PS) and the Lal\.fodel programs have been used successfully in the U.S. for designing safe pillar recovery operations for many years. However, the recent Crandall Canyon l\.fine collapse showed that further research is required to improve the pillar design for recovery under deep cover.Pillar recovery accounts for less than 10% of the coal produced from underground coal mines; however, in the period between 1989 and 1996, it accounted for more than 25% of all ground fatalities (l\.fark et al., 2003). In the past 15 years, the safety of retreat mining operations has greatly improved. l\.fark (2009) explains three steps promoted by l\1SHA and NIOSH for safer pillar recovery:1) Global stability through proper pillar design2) Local stability through proper roof support3) Worker safety through proper section managementThe ARJ\1PS and Lal\.fodel (Heasley, 1998) programs have been playing an important role in guiding mine operators in designing pillars to ensure the global stability of a retreat panel."

Jan 1, 2010

By Christopher Mark

Dr. Christopher Mark serves as Team Leader of the Rock Mechanics Section in the Rock Safety Engineering Branch of the NIOSH - Pittsburgh Research Laboratory. In this position he leads a multi-disciplinary team and conducts individual research directed towards fundamental ground control safety issues affecting miners. Dr. Mark is recognized as one of the country?s leading authorities on coal mine ground control. Through his research, he has made numerous important contributions to mine safety that have been widely adopted into mining practice. He is a highly original researcher, and has often developed new and innovative methods to tackle extremely complex problems in his field. In recent years Dr. Mark has also achieved wide international recognition. Five research projects in Canada, Australia, and South Africa have been based largely on his work.

Jan 1, 2007

By Yongjie Yang

Experimental study on the strength and deformation characteristics of coal under cyclic loading provides guidance for designing coal pillar which is subjected to repeated mining influence during mining. This paper studies the strength, deformation and fatigue process of No.3 coal from Xinhe Colliery under cyclic loading by the MTS815.03 servo-controlled rock mechanics test system. The results indicate that coal is more susceptible to fatigue damage than other hard rocks. Under uniaxial cyclic loading, the fatigue failure ?threshold value? of coal is smaller than 78% of its uniaxial strength, and there is also some fatigue damage when cyclic loading and unloading experiment is carried out below the fatigue failure ?threshold value?. Axial deformation can be divided into three stages: Initial deformation, steady-state deformation and accelerating deformation. Transverse deformation can be divided into two stages: Stable deformation and accelerating deformation. When the transverse deformation begins to increase rapidly and the deformation recovers only slightly upon unloading, it?s a precursor to failure of coal. Under cyclic loading, fatigue failure develops through a process of compaction, strain hardening, and strain softening.

Jan 1, 2006

By Jesse L. Craft

Field investigation of surface subsidence events associated with both active and abandoned underground coal mines in the United States has established criteria that enable the prediction and classification of mine-related subsidence. The key was establishing the role of geology in all types of subsidence and the recognition of beam subsidence in specific geologic settings. The classification is based on overburden thickness, variations in stratigraphy, topography and mine plan. Types of subsidence are Pit, Room, Sag, and Beam. Pit subsidence is associated with three geologic settings: shale overburden, seasonally wet unconsolidated overburden, and perched water table in unconsolidated overburden. Room subsidence occurs where the roof across the width of the room fails to the surface and a shallow depression develops. Sag subsidence develops where the pillars are failing in conjunction with roof failure. Overburden thickness is generally greater than 150 feet. Beam subsidence can occur in all terrains. It is associated with retreat mining and room and pillar mining where pillar crushing or pillar compression has taken place and barriers are left inplace. They occur as beam arch or one-sided beam subsidence. Beam arch failure occurs where mining has taken place on both sides of a coal barrier. One-sided beam failure is associated with retreat mining moving from a barrier towards the entry in hilly topography. This type of subsidence occurs where a hard, thick, rock unit is acting as a bridge supporting the overburden and outcrops on the hill side.

Jan 1, 1992

This paper is not available for inclusion in the Proceedings at the time of printing, but it will be included as an insert.

Jan 1, 1984

By G. P. Neobutov

The near surface inclined gold ore deposit is mined out at freezing temperature. The replacement of ore pillars by artificial freezing rocks during the rock pressures control in this conditions presented no difficulties. At the present, the mining operations are maintained at a depth of more than 300 meters. The exploration of mining conditions showed partial warming of rock mass and unstable ground conditions. Analytical calculations using a mathematical model of heat exchange predicted undesirable duration of freezing of artificial pillars. Practical techniques and recommendations for mining with ice pillars as an artificial support system using a new freezing method are discussed.

Jan 1, 1996

By Zhanjing Yu

Longwall ground behavior in the Illinois Coal Basin was studied in the past (1, 2, 3). Most of the past studies, however, were concentrated on either surface subsidence or underground structural behavior. In this study, both surface and in-mine ground behaviors are considered, which include: 1) stress and deformation characteristics in the chain pillars; 2) roof and floor deformations; 3) surface subsidence characteristics, including time effect; 4) relationship between the surface subsidence and underground strata behavior; and 5) the ultimate hearing capacity underneath the chain pillars. Field measurements and tests were conducted and the data were analyzed using both analytical and statistical methods. The findings in this study can he used by mine operators in the Illinois Coal Basin for longwall ground control planning and design.

Jan 1, 1994

By M. W. Fabjanczyk

Cement and resin encapsulated tendons are widely used in the stabilisation of mine roadways. One of the main factors in controlling the efficiency of the reinforcement is the ability of the tendon to generate load in response to rock deformation. The analysis of field data from instrumented reinforcing tendons complimented with extensive laboratory investigations have more accurately defined the mechanisms by which load generation occurs. The role of reinforcing tendon profiles, hole geometry and encapsulation medium properties in controlling the reinforcement stiffness and capacity are discussed. The results of the investigation have implications in both the design of rock reinforcing systems and the optimisation of encapsulation mediums and tendons.

Jan 1, 1992