Search Documents

By St. Mergentime, K. Zeidler, V. Gall

2001, the New Jersey Transit Authority commissioned the JV Merco-Obayashi with the rehabilitation contract of the approximately 130-year-old, 4,200 ft long, partially brick- lined Bergen North Tunnel. The contract entailed the tunnel enlargement, shotcrete and rock dowels initial support according to the NATM, a waterproofing system, tunnel drainage and a cast-in-place concrete lining. The rock conditions encountered required design adaptations and significant modifications of the initial tunnel support. Flexibility, skill and extensive experience on the Authority’s and Contractor’s side finally lead to a success. This paper describes the operations and design modifications carried out.

Jan 1, 2003

By K. Soucek

Extraction of hard coal reserves, but also of mineral resources in general in the underground coal mines includes in itself many anthropogenic interventions in the earth crust. These interventions are closely associated with the solution of stability problems in the mine and with occupational safety. One of potential applications of such geo-technical interventions in rock mass is the chemical grouting technology. The chemical grouts are very suitable to affect the physical and chemical properties of rock mass. With the present development of chemical grouts, primarily based on polymers, there come into existence new composite materials during the grouting process (the so called geo-composites), which properties significantly differ from the original rock. An important factor, which affects a choice of chemical grouts and at the same time the effectiveness of grouting technology is the resulting properties of geo-composites. The properties of a coal geo-composite differ from the ones of the unmodified coal seam. On the basis of the laboratory geo-mechanical tests, the differences of properties of both material types were found. While the pure coal samples were destroyed very brittle and explosive, the geo-composite samples were making higher level of tenacity and load bearing ability after overstep of material strength. The presented paper discusses the different behaviour of these original and modified coal samples. The X-ray CT scans were used for observation and demonstration of failure evolution in these samples of pure coal and coal geo-composites after compressive loading.

Jan 1, 2006

By Sarkis G. Ampian

This late 1979 Bureau of Mines report presents current stocks and monthly consumption rates for Guyanese refractory bauxite (GRB), with emphasis on the impact of the GRB shortage on the refractory and downstream industries, general background material, and an evaluation of the situation resulting from the strike of Guyanese bauxite workers during the summer of 1979. A study by the Bureau indicated that industry stocks contained little more than a month's supply of GRB--30,000 calcined short tons (CST), at present consumption rates of 25,000 CST per month. The report was requested by the Federal Emergency Management Agency (FW) in response to refractory industry requests that the Government release GRB from the National Stockpile to minimize forecasted industry problems. The report traces the historical innovations in the high-alumina and/or bauxite-type refractory products industry, eventually leading up to fabrication of modern, high-quality firebrick and monolithic refractories.

Jan 1, 1980

By A. T. Iannacchione

Recent fatal injuries occurring during pillar retreat coal mining call for better identification of the hazards and recognition of risks. Ground control hazards associated with room-and-pillar retreat mining tend to intensify with depth, requiring extra precautions in the form of additional controls. In many locations these activities are further complicated by local complexities often associated with unique or novel circumstances, such as over-mining or under-mining. One technique recently studied by NIOSH, Major Hazard Risk Assessment (MHRA), may help mine operators to mitigate the risks associated with pillar recovery operations. The approach was trialed at two underground coal mines in southern West Virginia that are currently practicing pillar recovery. The first step in the MHRA process involved reviewing the segments or parts of the pillar extraction mining system and identifying associated hazards and threats to the operation. Some of the high risk hazards at these two sites included: ? Rock fall during pillar extraction covers equipment and injury occurs during recovery operations, ? Rock fall above the roof bolt horizon, potentially injuring ? workers and/or requiring recovery action, ? Rib fall under deep cover, potentially injuring workers, and; ? Strata instabilities associated with subsidence of the interburden due to simultaneously mining two seams in close vertical proximity to one another. The mines? risk assessment teams then considered each threat individually in order to systematically identify potential unwanted events. The top unwanted events were examined individually using structured risk analysis tools. The output from the process includes a list of priority existing controls for monitoring and auditing, and a second list of potential new controls. These controls consisted of: Examples of best practices, ? Enhanced communication, ? Implementing standard operating procedures (SOP), ? Protocols for emergency response actions, ? Effective layouts, ? Efficient monitoring, and; ? Successful audits. This paper documents the process as it unfolded at the two mines, and analyzes the strengths and weaknesses of the MHRA technique as it applies to pillar recovery operations. This work was part of a larger NIOSH research project. NIOSH was responsible for: 1) facilitating the risk assessment process known as Major Hazard Risk Assessment (MHRA), 2) documenting the risk assessment process, and 3) providing mine management with a written draft summary of the risk assessment process. The results of the risk assessment represent the thoughts and opinions of the individual risk assessment teams and should in no way be construed as an endorsement of the risk assessment output by NIOSH or the University of Pittsburgh.

Jan 1, 2009

By Daniel W. H. Su

The ability to predict the effects of longwall mining on topography and surface structures is important for any coal company in making permit applications and anticipating potential mining problems. The sophisticated finite element model described and evaluated in this paper is based upon five years of underground and surface observations and evolutionary development of modeling techniques and attributes. The model provides a very powerful tool to address subsidence and other ground control questions. The model can be used to calculate post-mining stress and strain conditions at any horizon between the mine and the ground surface. This holds the promise of assisting in the prediction of mining-related hydrological effects.

Jan 1, 1986

By K. A. Brunk

This paper describes Newmont's research, operations, history and experience with pre-treatment of preg robbing carbonaceous ores. The chemistry, physics and kinetics of chlorine treatment are described. Present operations, control strategy and projected changes are discussed. Included is a summary of the adsorption of chlorine into pulps and off-gas scrubbing.

Jan 1, 1987

By Robert W. Lawson

INTRODUCTION Prior to 1705, underground mining was limited to mineral deposits located above or a very small distance below the water table. The development of the steamdriven mining pump was motivated by the need to extract minerals from deposits considerably lower than the water table. Today, the majority of mine pumps are driven by electric motors, although some small utility pumps are driven by compressed air. Of the numerous types of pumps that might be applied to mine service, the two types used most frequently underground are the centrifugal and plunger pumps. Each of these types has its proper application. In most instances, plunger pumps are best for handling low water volumes against high heads, while centrifugal pumps effectively handle either low or high water volumes against low heads or high water volumes against high heads. This chapter describes pumps applied to underground mine service, where the mine service consists of mine drainage (removing mine water as it accumulates), mine dewatering (removing water from a flooded mine), and pumping for special applications such as hydraulic mining and hydraulic hoisting. CENTRIFUGAL AND PLUNGER PUMPS Modern mine pumps are classified as either centrifugal (kinetic) or plunger (positive-displacement) pumps. The following paragraphs describe each of these classifications. Centrifugal Pumps Centrifugal pumps may be grouped into various types, depending upon their various features: Number of Stages: In a single-stage pump, the total head is developed by one impeller, while a multi¬stage pump utilizes two or more impellers acting in one casing to develop the total head. Fig. I shows a cutaway view of a single-stage horizontal split-case double -section centrifugal pump. Fig. 2 shows a cutaway view of a six-stage medium-pressure split-case diffuser-type centrifugal pump. Type of Casing: A volute pump has a casing in the form of a spiral or volute. A circular-casing pump has a casing of constant cross section concentric with the impeller. A diffuser pump is equipped with a diffuser that converts velocity head to pressure head. Shaft Position: A horizontal pump normally has the shaft in a horizontal position, while a vertical pump normally has the shaft in a vertical position. Fig. 3 illustrates a vertical turbine-type slurry pump. Suction: A single-suction pump equips the first stage with a single-suction impeller, with fluid entering the impeller on only one side. A double-suction pump equips

Jan 1, 1982

It took me nearly nine months to make the move from Arizona to Berkeley, opening an office and planning our new home. While I was in Warren Dorothy had rented two rooms for my office In the new California Commercial Union Building at 315 Montgomery Street in San Francisco. She made such a good choice that this remained my address for more than 50 years Dorothy had also looked over many lots In Berkeley, and took an option on the one that pleased her the most. It was a beautiful lot, or rather three, as we took three lots to protect our view. The only possible drawback was that it was in a new district and there were only two houses within two blocks. No one could tell how the area would develop but we liked it so much that we bought the lots on the spot and signed a note to guarantee payment. Dorothy's good judgment was shown by the fact that after 50 years we are still glad to be living on the same property, at 168 Southampton Avenue. We arranged a meeting with the distinguished architect Bernard Maybeck-and employed him to design a house for us. Dorothy spent most of her time with Maybeck planning the house and an attached studio for her, and she later wrote an amusing essay on her dealings with Maybeck. They were so successful that even now we could not think of any changes we would have wanted. It took several months to design a house that suited Dorothy and would fit on our hilltop. I was glad to overcome some of Maybeck's scorn for "only an engineer" by showing how, by rotating the studio addition 45º, it would fit the lot without serious excavation. We finally signed a contract with Maybeck, borrowing so much money that it scared us. First Consulting After short jumps to the gold mines in the Secret Pass District near Kingman, Ariz., and to the Espiritu Santo prospect adjoining the rich

Jan 1, 1976

By Henri Letient, Tom Aley, David Evans

Antamina is a large open-pit copper and zinc mine located within the Central Andes of Northern Peru at an altitude of 4300 masl. The facilities are situated within the headwaters of several watersheds, within the Amazon basin. Nearby villages rely heavily on springs and streams for drinking and irrigation water. The principle source of baseflow during the dry season is from Cretaceous karstic limestone aquifers. Antamina will produce nearly 1.4 billion tonnes of waste rock over its mine life. Finding suitable sites for storing large volumes of waste rock is often a challenging task – especially in karstic, alpine terrain. Detailed hydrogeological investigations are essential for delineating the karstic hydrogeologic watersheds associated with the proposed waste facilities, which are often very different than topographic (hydrologic) watersheds. Contamination vulnerability mapping at Antamina consisted of geological and karst mapping, geophysical surveys, geochemical testing, dye-tracer studies, drilling and aquifer testing. Detailed mapping followed by dye-tracer studies proved to be the most cost-effective methods for characterizing the karst aquifer systems. The results were used to optimize waste rock management at the site to minimize potential impacts on groundwater resources.

Jan 1, 2005

By Bruce Hebblewhite

"Historically there have been a number of different hypotheses and empirical models developed in an attempt to describe the nature of fracturing above longwall panels in underground coal mining. The motivation for such models varies, ranging from understanding the impact of mining on surface subsidence to back-analysis of caving behaviour in the immediate roof behind the longwall face. One of the most critical motivating factors that is taking on increased importance in many coalfields is the need for better understanding, and hence prediction of the impact of mining on overlying strata, particularly strata units acting as aquifers for different groundwater horizons.This paper reviews some of the major prediction models in the context of observed behaviour of strata displacement and fracturing above longwall panels in the Southern Coalfields of New South Wales, south of Sydney. The paper discusses the parameter often referred to as “height of fracturing” in terms of the critical parameters that influence it, and the relevance and appropriateness of this terminology in the context of overlying sub-surface subsidence and groundwater impact. The paper proposes an alternative terminology for this parameter that better reflects what it is and how it is used. The paper also addresses the potential role of major bedding shear planes mobilised by mining and their potential influence on overlying subsidence and groundwater interference.INTRODUCTIONKnowledge of the detailed nature of rock deformation and failure above any form of large-scale underground mining is always going to be limited to interpretation from a very incomplete set of data. It is extremely difficult, if not impossible, to directly measure the detailed nature of the rock failure, fracture networks, and deformational behaviour above an extracted mining area. Limited techniques such as borehole extensometry can provide some evidence of relative or incremental deformation in the direction of the borehole (usually vertical). However, such data cannot assist below the horizon where full caving has caused major rotation and dislocation of rock blocks and effectively destroyed the instrumentation borehole. Above such a horizon, the data is only valid along the axis and in the direction of the borehole, and to the level of detail defined by the extensometer anchor spacing intervals. It is often also restricted by major shear planes intersecting the extensometer borehole and cutting off the instrumentation below the level of the shear horizons."

Jan 1, 2019

By Bernie W. Martin, Jesus Schabib

The East Side Access (ESA) Project in New York will be the largest tunneling project ever undertaken by a US railroad. The objective of the ESA project is to connect the Long Island Rail Road (LIRR) Main Line and Port Washington Line in Queens to Grand Central Terminal in Manhattan. The Project is divided into two distinctive segments: Manhattan and Queens. The Queens segment is subdivided into two major components; cut and cover tunnel construction and bored tunnels. The bored tunnels in Queens consist of five tunnels driven from a launch shaft and traverse a railway storage yard, Sunnyside Yard and terminate under the multitrack mainlines of Amtrak and LIRR at portals in the heart of Harold Interlocking where1200 trains pass every day. The soil consists of remnants of glacial till moraines and of outwash and till deposits of inter layered gravel and fines, with the occasional boulders and cobbles and with a high ground water table. It is anticipated that a Pressurized Face Machine, either slurry or Earth Pressure Balance equipped with roller disks to mine the boulders encountered as well as the mixed face, will be used to mine the tunnels. One pass reinforced concrete gasket bolted liner will be used. The cut and cover construction consists of an approximately 21.3 m (70 feet) deep excavation supported by slurry walls and jet grout columns. The slurry walls, in combination with overlapping jet grouted columns, are installed to top of rock forming a closed bathtub to control external groundwater drawdown. Maintaining the groundwater level near its original elevation is of paramount importance in order to prevent undesirable settlements and migration of groundwater that could be contaminated. Mitigation measures to prevent the migration of nearby plums are contemplated for all types of tunneling and excavation work in this site of the ESA project.

Jan 1, 2001

By M. Fofana

The use of a laboratory-scale magnetic fluid-based separator for coal separations was examined. A Frantz laboratory magnetic separator was modified by fabricating new pole pieces of the appropriate geometry to provide the proper magnetic field gradients. Two separation chambers, which were constructed out of Plexiglas, were designed to fit between the pole pieces. A commercially available, water-based, ferro-magnetic fluid was used as the separating medium. The separating density was changed by varying the intensity of the electromagnet. Both batch and continuous separations were made using 0.59x0.50 and 0.18x0.15 mm coal. The results are compared to those obtained using organic liquids.

Jan 1, 1996

By L. M. English

In the past 30 years, the research arena has changed significantly in all fields, mining included. The relative representation of the topics of research, how the research is performed, and who has performed the research have all changed significantly over these decades. Although there are a lot of subjective ideas concerning these changes, and there is a fair amount of anecdotal "analysis," there has been no actual study of these trends to verify the facts. The period studied is divided into six five-year periods for the purposes of comparison. Some of the trends analyzed are as follows: ? Co-authorship ? Research areas ? Research sponsors ? Cooperative efforts

Jan 1, 1995

By M. Visnjic

Open Pit Mine Production scheduling under commodity price uncertainty suffers from an exponentially increasing problem size as simulations and real options flexibility are used to generate and evaluate multiple production schedules. Robustness evaluation techniques attempt to evaluate a production schedule that is generated on a single set of economic parameters against several varying prices and sources of uncertainty. This approach is invalid as the corresponding optimal LOM mine plan will change for each set of evaluation parameters. Using commodity market futures and treasury bonds as production schedule economic input parameters provides fully price and time-value-of-money risked scheduling parameters that maintain a deterministic problem size. This paper will provide comparative analysis of project NPV’s coming from traditional price uncertainty evaluation based on a single fixed LOM mine plan using varying prices versus evaluation based on varying LOM plans that are both generated and evaluated using varying prices. When cross evaluating constant price mine plans against simulations, the upside potential and downside risk of a project are significantly misrepresented. INTRODUCTION The life of mine (LOM) production scheduling problem seeks to answer the question of from where and when to extract a given block within the ultimate pit limit as well as where and when to process it. Solving this problem takes into account the constraints of extracting any particular block while seeking to maximize the net present value (NPV) of the mineral asset as a whole. A direct driver of the value of a block, and there for the entire asset, is the market price of the commodity in question. Complications arise when an optimal production schedule is attempted to be solved under price uncertainty. Many solution methodologies have been proposed in an attempt to optimize under this criterion, yet there are three salient aspects that are overlooked during this process. They are: • Generating a single production schedule and evaluating it against many simulated price paths. • Failing to understand the mechanism describing particular commodity price behavior • Inappropriate risk adjustment In an effort to address these aspects of production scheduling under commodity price uncertainty, we propose a methodology to define the economic parameters as input that is applicable to most if not all production scheduling approaches. This methodology will not only simplify the production scheduling process in terms of establishing block value but utilizes the risk adjustment of real options valuation to avoid the arbitrary blanket risk adjustment of traditional discounted cash flow valuation. Our findings conclude that attempting to optimize around individual price paths is futile and using a market risk adjusted single price forecast provides a justified economic basis for production scheduling while maintaining the same problem size as a deterministic production scheduling problem.

Jan 1, 2019

By E. Watkins, V. Gangrade, P. Zhang, J. Addis, D. W. H. Su, T. Minoski, C. Hollerich, M. Van Dyke, S. Schatzel, H. Dougherty

"This paper presents the results of a comprehensive study conducted by the Centers for Disease Control (CDC), National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD) to evaluate the effects of longwall-induced subsurface deformations and permeability changes on shale gas well integrity and safety under shallow cover. NIOSH researchers selected a study site over a southwestern Pennsylvania coal mine, which extracts 1,500-ft-wide longwall faces under 482 feet of cover. One in-place inclinometer well and three permeability monitoring wells were drilled and installed over a 125-ft by 275-ft centers abutment pillar. In addition to the inclinometer well and monitoring wells, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the first 1,500-ft-wide longwall panel on the south side of the abutment pillar mined by the site.A number of FLAC3D finite difference simulations (Itasca Consulting, 2017) were conducted to estimate surface subsidence, coal pillar pressure increases, and horizontal displacements in the in-place inclinometer (IPI) monitoring well. Comparisons of the FLAC3D finite difference simulation results and the surface, subsurface, and underground instrumentation results show that the measured IPI casing deformations are in reasonable agreement with those predicted by the FLAC3D models, and that the measured surface subsidence and underground pillar pressure are in excellent agreement with those predicted by the 3D models. Measured permeability changes were incorporated into a preliminary calculation to evaluate the effect of a hypothetical shale gas well leak on longwall ventilation. Results from this 2018 research clearly indicate that under shallow cover, the measured horizontal displacements within the abutment pillar are at least one order of magnitude higher than those measured in a 2017 study under deep cover and slightly higher than those measured in a 2014 study under medium cover. This research represents a very important step and initiative in utilizing the knowledge and science obtained from mining research to improve miner and public safety as well as the safety and health of the workers in the oil and gas industries"

Jan 1, 2019

By W. J. McDonough

Rapid growth and acceptance of engineered materials have changed the way we live. We have come to expect improved performance at less cost. At the same time, our awareness of societal and environmental issues created by these materials during and after their lifetime has been heightened. As a result, material lifecycle analysis is receiving considerable attention. Material lifecycle analysis evaluates the cost/effective tradeoffs at each stage of a material's life: feedstock, fabrication, performance, recycle, and disposal. The U.S. Bureau of Mines investigates a material's lifecycle using technical cost models augmented with decision and impact analyses. Results of these studies are useful in gaining a better understanding of current material selections and illustrating the multifaceted issues associated with engineered materials in today's society.

Jan 1, 1992

By John W. Welty

Volcanic activity occurred during six periods of Arizona's geologic history. Precambrian volcanism occurred in two pulses at 1.8-1.6 billion years (b.y.) ago and at 1.2-1.1 b.y. ago. Volcanism occurred again in mid-Jurassic and Laramide (Late Cretaceousearly Tertiary) time. Volcanic rocks from these times are not used commercially in any significant quantity. Middle and late Cenozoic magmatic activity covered large areas of Arizona with voluminous volcanic rocks. During the mid-Tertiary magmatic pulse, explosive silicic magmatism, with eruption of areally extensive ash-flow tufts, covered large areas in the Basin and Range Province, while the Colorado Plateau remained largely unaffected. Basalt eruption also occurred during and immediately after silicic volcanism, leading to compositionally diverse suites of volcanic rocks. Late Cenozoic volcanism occurred throughout Arizona and was dominated by wide-spread eruption of basalt flows with local cinder-cone clusters and siliceous volcanic deposits. Perlite deposits near Picketpost Mountain in northeastern Pinal County account for the bulk of the industrial uses of mid-Cenozoic volcanic rocks. Other perlites of presumed middle Tertiary age are present in central, southeastern, and western Arizona, but to date remain unexploited. Arizona Fire Agate is a valuable gem material and is associated with volcanic rocks of middle Tertiary age. Basaltic rock of this age also is utilized in the manufacture of rock wool for insulation. Late Cenozoic volcanism produced most of the industrial-quality volcanic rocks. Basalt, cinder cones, and materials of rhyolitic composition are commercially exploited by municipal and Federal agencies and private industry for aggregates, road conditioners and maintenance materials, asphaltic concretes, cinder block construction, pozzolans, and landscaping. These deposits are generally confined to the Flagstaff and Springerville areas. A famous peridot gem locality is associated with late Tertiary basalts at Peridot Mesa on the San Carlos Indian Reservation. Important products derived from altered volcanic materials of late Cenozoic age include clay and zeolite. Arizona's volcanic-rock sequences are still incompletely known, particularly in central and western Arizona. The potential for recognition and exploitation of important new deposits of useful volcanic materials is high.

Jan 1, 1987

By James J. Scott

Shale formations are the Nemesis of the Mining Engineer. Shales react to changes in environment in the most unusual and unpredictable manner. Increase in temperature may cause spalling, increase moisture and compression induced fractures may occur, and if a full face is exposed it may deteriorate due to atmospheric exposure. Combine only small amounts of shale in layered fashion with hard brittle competent rock and the whole structure may be fractured and fail due to stresses generated in and around the shale. In this paper the author will discuss failure mechanisms encountered under various field conditions and remedial action which may be employed by the engineer.

Jan 1, 1969

By Y. A. Attia

Auriferous sulfide ores often contain very finely disseminated gold and other precious metal particles inside the sulfide crystals. The encapsulation of precious metal particles gives rise to the refractory nature of such ores to current extraction methods. As a result, these fractions are frequently lost in the tailings. The purpose of this work was to investigate the feasibility of pretreating these refractory tailings with bioleaching before employing standard extraction techniques such as cyanidation. Leadville gold ore tailings containing auriferous pyrite were first concentrated by froth flotation. The pyrite concentrate was treated for different periods of time with 12 weeks adapted thiobacillus ferrooxidans before cyanide leaching. The bioleaching of the concentrate before cyanide leaching increased the gold extraction from 32% to 95% and that of silver from 48% to more than 98%.

Jan 1, 1987

By B. J. Scheiner

The Bureau of Mines, U.S. Department of the Interior, has investigated the use of rheology to provide insight into the mechanism of flocculation. A technique developed by Tattersall has been modified and used to explain the flocculation of calcium montmorillonite with polyethylene oxide. The results indicated that there are two types of bond systems operating during the flocculation sequence. Also, flocculation results are highly dependent on the shear rate and the amount of polymer added.

Jan 1, 1989