Search Documents

By Paul Mitchell, Clive Potter, Miles Watkins

Meldon Quarry is a seemingly rare occurrence of acid rock drainage (ARD) in a quarrying operation.4 With surface waters discharging to a tributary of a salmon-bearing river, it is subject to stringent discharge conditions. The quarry predates effective environmental management, and preventative, control and treatment measures were not implemented until relatively recently. However, retrospectively implementing standard preventative approaches at the site is costly, technically difficult and of uncertain benefit. This paper overviews the recent site history and introduces data from a demonstration by KEECO (UK) Limited of its Silica Micro Encapsulation (SME) water treatment technology.

Jan 1, 2000

By Neil Hepworth

Neves Corvo Mine employs four mining and four backfill methods, including paste fill. The paper shows how the strength requirement for backfill in primary stopes was calculated and the relationship between laboratory strength and in situ strength requirement. The liquefaction of paste in secondary stopes is discussed with methods to determine the liquefaction potential. It was found from laboratory tests and the preliminary results of the underground trial, that the liquefaction potential of the paste is low at 2% and is high at 0.5% cement. The results to date are inconclusive regarding 1% cement.

Jan 1, 2001

By V. Galla

In the present paper, two large diameter columns 2 m tall and 1.3 m diameter filled with crushed (finer) and run off mine (coarser) heap leach materials respectively were used to perform unsaturated flow studies. Instruments measuring moisture content and matric suction were placed in the columns at different depths as water was applied at calibrated flow rates from the top of the columns. The outflows from the columns were recorded using tipping bucket rain gauge placed at the bottom of the columns. Unsaturated hydraulic parameters were also obtained for the heap leach materials, scalped (passing 4.75 mm sieve size) and whole (passing 37.5 mm sieve size) sample. The measurements obtained from the columns were later compared with unsaturated flow modeling results. The comparison indicated sensitivity towards the sample size selection for unsaturated hydraulic parameters, and initial conditions considered in the model.

Jan 1, 2009

By Donald W. Gentry

Mine valuation is a multifaceted, interdisciplinary process by which the economic viability of an old, existing, or new mining property or venture is determined. The problems associated with arriving at a representative and accurate value for a mining property are complex and numerous, and the procedures utilized in determining these values vary from simple, back-of-envelope calculations to sophisticated mathematical manipulations requiring computer modeling and analysis. Regardless of the complexity or the degree of sophistication associated with any particular project, the evaluation process must ultimately provide management with two basic types of information. First, the evaluation process should indicate whether or not the mining project is economically viable after careful consideration of all engineering, environmental, geologic, and other variables pertaining to the project. Second, the evaluation process should provide management in- formation on the relative attractiveness of the project when compared to other alternatives. In some cases, it may be extremely difficult to supply this information for a project directly. Nonetheless, the evaluation process should and must present all information necessary in a format which can be incorporated into the decision-making process as expeditiously as possible.

Jan 1, 1979

By Scott G. Britton

Many times during the construction of a project, whether large or small, the engineer will become involved with management of the work and workforce. In some cases, mine management will turn over the direction and responsibility of doing the work to the engineer. Because of this, it is important to know some of the basic principles of human resource applications- among other management concerns. This chapter, therefore, looks at the fundamental principles of human resource management. Three broad discussions are presented to the reader. These are: (1) organization, communications, and responsibilities of management; (2) analysis of worker motivation; and (3) supervisory leadership. Each topic encompasses the current thinking for coal mining and mining management. Much of the information in this chapter comes from Practical Coal Mine Management, by this author and published by John Wiley & Sons, Inc., which discusses in depth many of the ideas presented here. Interested persons are directed to this text for more information on management skills.

Jan 1, 1983

By Jianmin Qin, Raja V. Ramani

In this paper, the results of a research study on airborne dust transport in a full scale simulated longwall face are presented. The simulated longwall face was set up in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines to conduct experiments under controlled conditions. The controlled parameters in the experiments were the dust dispersion rate, dust size distribution, density of the dust, air velocity, and the rate of travel of the dust generating source. The analyses of the experimental results on mass concentrations, particle size distributions, and real-time respirable dust concentrations are discussed. There are definite spatio-temporal trends between the location of the shearer, the concentration at any location in the face, and the dust generation rates. The size-consist and density characteristics of the source dust, the air velocity in the face, and the air leakage into the gobs all affect the concentration.

Jan 1, 1995

By Christopher Laughton, Michael P. Bruen

At Fermilab, a 4000-ft long underground complex has recently been constructed for a high-energy physics experiment. The complex is sited up to 350 ft, below grade principally in bedrock. The rock excavations were mined by TBM and drill and blast methods and supported by a combination of rock bolts, dowels and shotcrete. Water control was achieved using a combination of pre- and post-excavation grouting, drainage systems, drip shielding and air desiccation measures.

Jan 1, 2003

By Robin B. Steven

Rio Tinto's Kennecott Bingham Canyon Mine is one of the largest open pit copper mines in the world. In 1988 they completed a $400 million project using a conveying system to transfer the ore from an in-pit crusher to the concentrator. The longest conveyor, C-6, was 17,352ft long and ran in a tunnel through the mountain-side to the concentrator. The belt was removed after 14+ years after carrying 700 million tons of 10 minus ore. The paper discusses the original G6 belt's performance and new splicing methods used to achieve a 60% dynamic splice efficiency on the replacement belt.

Jan 1, 2004

By Raul Z. L. Cançado, Virginia S. T. Ciminelli, Roberto Galery, Armando C. de Araujo

Brazil is presently among the seven largest gold producing countries in the world. This paper discusses the evolution of gold mining through the history of Brazil. It also gives a general account of the present practices for mining, processing and extraction of gold. Flowsheets of some selected plants are presented. The environmental aspects involved with gold production are also considered.

Jan 1, 1987

By John C. Heter

The P.W. Gillibrand Company holds 705 placer and lode claims in the Precambrian San Gabriel Anorthosite Complex of the western San Gabriel Mountains. These claims contain large tonnages of ilmenite, magnetite and apatite with anomalous quantities of zirconium (zircon), niobium, vanadium and rare earth elements. Stockpiling of heavy mineral concentrates associated with aggregate mining from alluvial pits has occurred since 1984. The limited reserves of material from these alluvial deposits and their relatively low heavy mineral grades caused Gillibrand Company to initiate an extensive drilling and exploration program to develop the hardrock resources of ilmenite, apatite and magnetite.

Jan 1, 1995

By Jim Jonas

The Berkeley pit-lake was sampled during two seasons, fall 1997 and spring 1998, from the surface to the bottom. Various parameters were measured to determine what effect the seasons had on the water column. It was determined that a seasonal turnover did occur between the fall and the spring sampling; however, the depth of mixing due to turnover could not be established. Trends were observed which suggested that microbial activity was altering the iron speciation at depth, and subsequently masking the extent of mixing. Various trace metals were removed from the surface water by either co-precipitation with schwertmannite or adsorption.

Jan 1, 2000

By S. Triantafyllidis

The tailings produced from the Kirki (Agios Filippos) high sulfidation epithermal deposit processing plant are laminated, weakly cemented and their particle size ranges from fine sand to fine silt. They are mainly composed of milling residues of gangue (quartz, dickite/kaolinite, pyrophyllite, illite); sulfides and secondary minerals (jarosite group minerals, butlerite, anglesite, beudantite and gypsum) are present to a lesser extent. They have high Pb and Zn (average 0.75 % and 0.57 % respectively) and low S (1.04 to 2.92 %), Cu, As, Cd, Ni and Sb content (average 248, 163, 59, 27, 20 g/t respectively). Stagnant waters forming small ponds on the surface of the impoundments exhibit low pH and high heavy metal and sulfate concentrations. Negative Net Neutralization Potential (NNP) characterizes the tailings, indicating moderate to high potential for acid generation. Application of the TCLP test revealed that the tailings are characterized as toxic because of the increased solubility of Pb and Cd. On the other hand, As TCLP solubility is very low.

Jan 1, 2006

By N. Parra, M. N. Herrera, T. Vargas, C. González, B. Escobar

The bioleaching of mineral sulfide pulps in a bench-scale rotating-drum reactor was studied. The reactor contained horizontal paddles on the inner wall for lifting the mineral pulp. The performance of the reactor was tested by bioleaching a refractory pyritic gold concentrate in the presence of pure Thiobacillus ferrooxidans (ATCC 19859). The concentrate was efficiently bioleached at a 50% pulp density with the drum operating at from 0.5 to 1.0 rpm. Attempts at bioleaching the concentrate at the same pulp density used in a conventional stirred reactor showed severe inhibition of bacterial activity. The results demonstrated that the drum reactor allows the process to operate at much higher pulp densities than conventional stirred-tank reactors. This results in improved bacterial activity because of better attrition control of the mineral particles.

Jan 1, 1999

By D. L. Kowal, P. J. Whittaker, M. A. Tuzun, N. O. Lotter

The area of flotation testing of drill-core is important in the business plan of most mining companies. Metallurgical information derived from this practice can be used to advantage in strategic decision-making. Sampling, flotation testing and subsequent Qem SCAN analysis of a mineral resource is one example of this approach. Anew resource, located in Sudbury, Ontario, is being assessed for the Sudbury Operations of Falconbridge Limited, which includes the Strathcona Mill. In this case, it was possible to improve the value of information from sampling and flotation testwork by using an improved, statistically-based test design, by sampling the resource by generic end-member ore type, and by integrating the Mineral Processing and Mineral Science disciplines into a Process Mineralogy team. In addition to producing standard metal grade and recovery information, this new approach provides more reproducible information from representative samples and flotation testing in a replicate format. Qem SCAN technology is used to produce a size by size mineral balance, including both modal percentages and liberation, from which flotation models for each ore type can be developed. As a result, a key understanding of the potential behaviour of a given ore type, if mined and then processed at the current mill operation, is gained at the 95%confidence level. The three ore types of this mineral resource were shown to have different flotation characteristics. Quantifying the mineralogy and liberation in each of the three ore types, has shown that this difference is due to changes in modal percentages of ferro-magnesium and magnesium silicate minerals such as pyroxene, talc and serpentine. Liberation across the three ore types is very similar and is therefore not responsible for variation in flotation performance.

Jan 1, 2003

By Pierre Ollivier, Dominique Morin, Pr. Ivo Toromanoff

Refractory gold ores have been processed by bio-hydrometallurgical process at B.R.G.M. (Bureau de Recherches Géologiques et Minières), Research Centre ,Orleans,France. The liberation of gold has been studied and the following steps for gold recovery improved. The overall process flowsheet has been established comprising different ways of treatment before the final discharge of the effluent. Iron and arsenic are successfully precipitated under well controlled Eh-pH conditions. Long term stability tests have been conducted and the research programme is to be continued with the crystallo graphic studies of the precipitates. Economical studies have been performed on the base of data obtained on parameters studies.

Jan 1, 1990

By S. K. Mukherjee, A. W. Laurito, M. M. Singh, N. I. Jayaraman

This paper describes the application of foam to control respirable dust in a double-drum longwall mining section. The feasibility of injecting an adequate quantity of foam through the shearer drum was initially established in the laboratory. Thereafter, underground testing of the foam system to determine its effectiveness on an active operating longwall was conducted in a mine in West Virginia. The foam system proved superior to the water spray system. The details of the laboratory and field investigations, the results obtained, and the degree of acceptance of this system by the mining company are discussed in this paper.

Jan 1, 1987

Crushing and grinding The Crushing and Grinding Technical Committee There was substantial activity in the area of crushing and grinding with the improved outlook in the industry. The Crushing and Grinding Committee's theme of 1987's Annual Meeting in Denver was Fundamentals of Mechanical Design for Crushing and Grinding Mills. At the meeting, the concept of gearless sag mill variable speed drives was taken out of the closet, dusted off, and a wraparound motor was put on hard copy with the ordering of a 9.7- x 4.5-m, 8.2-MW (32- x 15-ft, 11,000-) sag mill. Additionally, comparisons were provided to the mill design of the gearless drive sag mill and the twin 4.5 MW (6000 hp) do variable speed drives placed on the drawing board for the Kennecott UCD Expansions. This involved a 10- x 4.5m, 8.9 MW (34- x 15 ft, 12,000 hp) sag mill. Differing opinions were also expressed in technical presentations pertaining to the need for quality mill specifications in design and manufacturing. J. Berney-Ficklin of Bechtel presented a paper outlining the need for quality design and manufacturing specifications in large scale grinding mills, and the overall cost reduction in capital and operating costs. Others presented differing specific views, but all emphasized a central theme. Quality and reliable designs in large mills should not be compromised. In-pit crushing applications continue to increase, overseas and in the US, in both mining and quarrying. Different in-pit crushing units have been classified as mobile, with integral transport systems; semi-mobile, typically modular systems that use separate transporters for repositioning; semi-stationary plants that must be dismantled before transporting and typically require earthwork and concrete foundation work; and stationary in-pit crushing plants, which remain in place for the life of the pit. The majority of equipment sales of conventional crushing and grinding circuits in 1987 were to gold mining operations. There have been two areas of end use: • conventional jaw/gyratory or impact crushing circuits preparing low grade ores for heap leaching; and • small scale sag/ball mill circuits preparing higher grade ores for classical cyanide leach/ recovery circuits. There was also continued interest in ABC and SABC circuits for both base and precious metals plants. High pressure roll crushers continue to attract considerable interest in the cement industry. There, they are used to prepare raw materials or clinker for subsequent ball/tube milling. However, they have apparently been less successful in the mineral industry where the energy savings/ capacity gains have been much less dramatic. Several papers covering the theory and application of these machines were presented in an industrial minerals session on cement at the SME Annual Meeting. The Third International Conference on Hydrocylones, held in England in October produced several papers of interest on classification and screening to the mining industry. In particular, a new cyclone apex, developed by Mt. Newman Mining, shows promise of reducing water flow to the cyclone underflow stream and, therefore, increased underflow pulp densities and reduced fines recycle in grinding circuits. A twin vortex hydrocyclone was also described and shown to give a sharper split than conventional units. Similar double cyclones were introduced in the 1950's, but failed to achieve widespread acceptance. This was due mainly to a proneness to blockage in the transitional zone. It will be interesting to see whether this latest variant can overcome this problem in the typical operation. A number of North American iron ore plants installed the capability to produce fluxed iron ore pellets. Most chose to grind the stone on site with circuits designed to grind taconite ore. Methods employed to grind this material included single-stage ball mills closed with fine screens, rod and ball mill circuits - both open and closed with cyclones - and semiautogenous mills, followed by ball mills closed with screens or cyclones. Dewatering and tailings disposal B.M. Moudgil and D.L. Sober, University of Florida Due to tightened environmental regulations and the need for more efficient land use, a greater interest in dewatering and waste disposal has developed. As a result, research efforts in flocculation, surface chemistry, and polymers science have focused on the problems related to the dewatering of solid mineral wastes. A few studies have been conducted to examine the flocculation process. Hogg et al., (1987) discussed the formation and growth of flocs. They determined the size and density of flocs was controlled by the physical conditions of the system (e.g. agitation,

Jan 5, 1988

By B. K. Parekh, W. M. Goldberger

Sludge obtained during the production of magnesium (Mg) from molten MgCl2 by electrolysis contains entrapped magnesium particles. The sludge containing the magnesium particles is a friable, continuous matrix of frozen salts that may also contain some oxides and impurities. Due to the high reactivity of magnesium metal with water, a dry process was developed to recover magnesium metal from the sludge. The process utilizes mineral-processing unit operations. The steps include selective comminution, screening, attritioning and tabling. Recovery of the high-grade (>90%) metal was in the 70% range. The novel process was also successfully applied to a magnesium-alloy for the recovery of metal from the sludges.

Jan 1, 1997

By Pedro E. Rengifo

Splicing methods have undergone considerable developments over the last 2Oyears. Continuous conveyor belt service is dependent entirely on the strength and life of the splice to hold the two ends together. Ultimately, belting performance is dependent on the quality, efficiency, and technique of the splicer. As customers demand better belting performance and running tensions increase, the need for splices that perform as efficiently as the belting has increased also. Higher dynamic belt constructions have also dictated the need for "new"sp1icing techniques. Regardless of the belt type used or spliced, one item that is most necessary with all belt types is the quality of the workmanship and standardized splicing methods that employ all of the necessary elements required to ensure reliable field service. This paper will explore the use of Goodyear-issued internal standards for field splicing following the constraints of quality and efficiency for fabric and steel cord reinforced belting. Also included are the 10 most common mistakes made by splicers, Goodyear-issued Field Quality Assurance Standards, and check lists for end users to adhere to the manufacturers' requirements for splicing including materials and specifications for conveyor belt splicing and repairs.

Jan 1, 2004

By E. M. Frizzell

Decisions affecting ground control design require detailed knowledge of roof rock geology. This is especially true when weak roof materials and anomalies create hazardous conditions and. if not properly supported, result in roof falls. The U.S. Bureau of Mines has developed a system to evaluate geological conditions by using a roof drill that will provide an estimate of the compressive strength of the roof rock in real time. Through the use of sensors and a microcomputer on the roof drill critical drilling parameters can be interpreted and analyzed almost instantaneously, making it possible to inform an operator of hazardous roof conditions such as voids and changes in strata during the drilling process. Geotechnical data can be downloaded to a portable semiconductor memory device, which is brought to the surface so that data can be directly accessed with a personal computer for further analysis. Results from field tests are presented.

Jan 1, 1992