Search Documents

By Hubert E. Sherer

The mining industry is presently one of the most heavily capitalized industries in the U.S. (U.S. - Statistical Abstracts, 1979). U.S. sales of new mining equipment (not including environmental, preparation, or long distance transportation equipment) are projected to reach approximately $5 billion/year in 1980 (Frost and Sullivan, 1979). Of these new equipment sales approximately 30 to 40 percent of this equipment will be used to replace old equipment. Therefore, an increase of efficiency in the use of equipment replacement capital could have substantially positive effects for the U.S. mining industry. This is very critical in these times of restricted capital availability, double digit inflation, burdensome governmental regulation, and rising foreign competition in the mining industry. This paper examines the numerous factors that constitute the typical mine equipment replacement problem. A computerized, mathematical model is formulated to utilize historic cost and production information to predict equipment cost versus age for the existing and potential replacement machines. Another part of this computerized model determines the best equipment replacement strategy that accomplishes estimated production goals at a minimum discounted cost. This computerized model is an easily used, consistent method of determining the optimum replacement age for any equipment unit or fleet of equipment at a mining operation.

Jan 1, 1982

By C. M. Liu

"The Freeport-McMoRan Sierrita Crystal Plant produces Copper (II) Sulfate Pentahydrate (CuSO4·5H2O) through a series of cooling crystallizers. In this process, high supersaturation and unwanted spontaneous nucleation promote fine crystals. Seeding through recycled crystal classification can manipulate the crystal size distribution (CSD) for larger crystals. Proper selection of the crystallizer for seeding can prevent spontaneous nucleation and promote final crystal size. This study shows when seeding temperature is closer to the crystallizer temperature, suspension densities in the crystallizers are promoted and overall CSD shifts to a larger size of crystals. INTRODUCTION Figure 1 shows an overview of the crystallization process. The in-plant feed flow, called Pregnant Mother Liquor (PML), enters the first crystallizer and is subsequently cooled through a series of four crystallizers. Specific temperatures are targeted for each crystallizer to ensure the crystallization process is operating within the metastable zone (MSZ). The discharged flow from crystallizer #5 then enters two cyclones. The overflow from the cyclones contains smaller crystals providing seed crystals for crystallizer #5. The underflow from the cyclones begins the drying process. The overflow from crystallizer #5 enters cyclone #3 for removal of fine crystals and seeding purposes. The underflow from cyclone #3 has the capability to provide seed crystals for crystallizer #1 or crystallizer #2. The overflow leaves the system as Spent Mother Liquor (SML). Undersize crystals dissolve into the PML and return back to crystallizer #1.THEORIES AND METALLURGICAL TESTS Seeding requires an understanding of the crystal size, solution temperature and amount of crystals that enter the crystallizers (1). For the seed crystal size, classified crystal seeds can prevent fine crystals returning back into the system which eventually leads to excessive agglomeration (2). Proper selection of the crystallizer can ensure seeding at an appropriate temperature. Seeding at a temperature much lower or higher than the saturation temperature promotes spontaneous nucleation. Typically, seeding between 4-5°F below the saturation temperature is acceptable (5). A general rule of thumb is to add the seed crystals at the temperature between the solubility curve and the metastable zone. An experiment conducted by Mettler-Toledo AutoChem, Inc. indicates seeding close to the solubility curve rather than the metastable zone promotes a lower supersaturation and nucleation rate but yields a higher growth rate and a greater number of larger crystals (1). The amount of seed crystals can not only change the suspension density but also narrows the width of the MSZ in the crystallizers. An experiment conducted by Jaroslav Nyvlt reports with the crystals absent, the maximum allowable undercooling is 6.3 degrees at a cooling rate, 5°C/hour. With the presence of crystals, it narrows the MSZ width to 2.2 degrees (4). Industrial crystallizers normally operate at suspension densities between 15% and 25% by mass. When suspension densities are lower than 15%, it increases the risk of primary nucleation and the probability of incrustations; on the other hand, if the suspension densities are greater than 25%, it can cause a greater attrition rate and increase the probability of deposits (6). Moreover, operating suspension densities between 15% and 25% are also sufficient to minimize supersaturation rate which promotes crystal growth over nucleation (2, 6)."

Jan 1, 2015

By R. A. Kirkland

The oxygen consumption method utilises an oxygen sensor to monitor the gas-phase oxygen concentrations in sealed chambers filled with reactive waste rock with subsequent confirmation of the oxygen content by gas chromatography. Results of experiments utilising low sulphide (<0.5w1%) waste rock yielded reproducible oxygen consumption rates on the order of 10-10 mol O2.kg-1. s-1. Petrographic analysis of the waste rock material indicated that the dominant sulphide mineral is pyrite (FeS2). Assuming a stoichiometry of 1.75 moles of O2 per mole of SO4 sulphate release rates were inferred to be between 6 and 18 mg SO4 kg-1 wk-1 Typically these results are 2 to 3 times greater than measured sulphate release rates from humidity cells. Our findings suggest that this techniques offers a rapid. cost efficient method for determining sulphate release rates in waste rock piles, even at low sulphide concentrations.

Jan 1, 2000

By D. R. Schricker

Mine managers rely on their experience, section foreman&apos;s daily reports and occasional time studies to make important production, maintenance and forecasting decisions. This information is often subjective and imprecise, consumes expensive engineers time, is often biased and is restricted to short time periods. Managers need better information. Furthermore, if a recently purchased machine is being evaluated, a large increase (>10%) in productivity may be obvious, but small increases are usually masked by other variables. In today&apos;s highly competitive markets, cumulative small changes are important, especially since managers have already exhausted most available, obvious avenues of improvement. A technique to separate these charges from effects of other variables and to quantify the target effect is necessary. CSM researchers are addressing this need by developing an intelligent decision support system (IDSS). It provides key production and maintenance information to support management decisions by recognizing patterns in mining machine sensor data and representing knowledge about mine management, operations, layout and equipment. A continuous miner section at Western Fuels-Utah Inc.&apos;s Deserado Mine in Rangely, CO is the test facility for the research. Power transducers located in the sections load center provide kilowatt versus time data from continuous section equipment. The IDSS pattern recognition algorithms classify the kilowatt versus time patterns into individual machine operating modes. It produces an output similar to a typical industrial engineering time study but continuously, automatically and without an engineer in the section. It is relatively easy for a time-study engineer to identify the stop and end points of a cycle element and classify it by looking at the machine and glancing at a stop watch. The problem is that monitoring system hardware and software do not have these unique capabilities. Consequently, IDSS algorithms must automatically define the begin and end points of machine tasks and identify the task by recognizing patterns in kilowatt versus time data. However, many mines have file drawers of time-study type data that are not very useful. So, IDSS contains the knowledge representation subsystem (IDSS/KRS) to produce short reports containing only key information. This is difficult because mine environments continually change and information requirements differ for each management level. Consequently, IDSS/KRS must learn and adapt to new conditions in a dynamic mining environment.

Jan 1, 1990

By Brian Fulcher, John Eastlund, J. B. Copeland

Following the completion of the 7,600 m primary access tunnel by Kiewit/Parsons Brinckerhoff (K/PB) in April 1997, an exploratory East-West Cross Drift Tunnel was constructed at the Yucca Mountain Project over the proposed future repository block for high level nuclear wastes. The 2,681 m (8,796 LF) East-West Cross Drift Tunnel was excavated through volcanic tuffs having zones of incompetent rock using a re-built Robbins 5.000 m (16’-5”) hardrock TBM with a special arrangement of supporting equipment. Details of the unusual site and contract conditions will be discussed as well as with the unique tunnel equipment specified by the Owner. This portion of the Yucca Mountain project required eight months to complete.

Jan 1, 1999

By D. Panias

Alumina hydroxides such as gibbsite (Al(OH)3) and boehmite (AlOOH) are precursors of many types of alumina that find important industrial applications. The thermal decomposition of AlOOH, which is a more energy saving precursor compared to gibbsite, gives rise to the formation of ?-, d-, ?- and a-aluminas that are used for the production of catalysts. The applications of the aluminas are governed by their properties that are a function of the precursor material and its microstructure. The microstructure in turn is a factor of the method and conditions applied, as well as, in the case of soft chemical processes, on the anions present. Towards these ends, this study was focused on the effect of different anions on the physicochemical characteristics of the alumina hydroxides precipitated in the first 5 minutes after the perturbation of the stability of a supersaturated sodium aluminate solution (Bayer liquor).

Jan 1, 2006

Industry and regulatory agencies have requested guidance on safe blasting near transmission pipelines. The US Bureau of Mines (USBM) and Amax Coal Co. studied surface coal mine overburden blasting near four steel and one PVC pipeline of 15 to 51 cm-diam (6-20 in.-diam), monitoring vibration, strain and pressure. Unlike tests of small blasts simulating construction, these were up to 1 t (2200lbs) per delay in 31-cm (12-in.) blastholes. Worst-case comparisons showed that 12.7 cm/sec (5 in./s) blasting vibrations produced strains about one fourth that of pressurization and 10% to 18% of the ultimate tensile strength. No failures occurred from blasting as close as 15 m (50 ft), which produced vibrations over 60 cm/sec (24 in./s).

Jan 1, 1995

By W. H. Pailes, V. Castranova, K. Van Dyke, J. H. Kang

Recruitment and activation of phagocytic cells after inhalation of occupational dusts has been implicated in the development of pulmonary inflammation, fibrosis, or emphysema. Plateletactivating factor has been described recently as a potent inflammatory agent. The objective of the present study was to investigate if platelet-activating factor might play a role in the inflammatory response of the lung to occupational dusts. In vitro exposure of alveolar macrophages to cotton dust (4 mg/ml), silica (10 mg/ml), or coal dust (10 mg/ml) results in the release of picomole levels of platelet-activating factor with a potency of cotton dust > silica > coal dust. Time course studies indicate that platelet-activating factor release from alveolar macrophages is maximal approximately 10 minutes after in vitro exposure to silica. In vitro, platelet-activating factor is a direct stimulant of polymorphonuclear leukocytes increasing chemiluminescence 2.3 ± 0.3 fold above control. The maximal response occurs in the dose range of 10-10 to 10-7M platelet activating factor. In addition, plateletactivating factor potentiates the response of polymorphonuclear leukocytes to a second stimulant; i.e., chemiluminescence generated from polymorphonuclear leukocytes exposed to plateletactivating factor (10-9M) plus chemotactic peptide (FMLP, 10-9M) is 88 ± 22% greater than the sum of the separate effects of these stimulants. In contrast, platelet-activating factor is not a direct stimulant of alveolar macrophages in vitro, having no stimulatory effect on chemiluminescence or superoxide anion release even at levels of 10-6 to 10-5M platelet-activating factor. However, platelet-activating factor (10-5M) does potentiate zymosan-stimulated activation of chemiluminescence and superoxide release from alveolar macrophages by 117 ± 56% and 30 ± 4%, respectively. In conclusion, these data indicate that exposure of the lung to occupational dusts results in the release of platelet-activating factor which may activate polymorphonuclear leukocytes and potentiate the responsiveness of alveolar macrophages to dust. The net result would be pulmonary inflammation and hypersecretion of reactive species by pulmonary phagocytes which could lead to tissue damage and pulmonary disease.

Jan 1, 1991

By Gregg A. Swayre, Roger N. Clark, Stephen J. Sutley, Kathleen S. Smith

Imaging spectroscopy is a relatively new remote sensing tool that provides a rapid method to screen entire mining districts for potential sources of surface acid drainage. An imaging spectrometer known as the Airborne Visible/InfraRed Imaging Spectrometer (AVIRIS) measures light reflected from the surface in 224 spectral channels from 0.4 - 2.5 µm. Spectral data from this instrument were used to evaluate mine waste at the California Gulch Superfluid Site near Leadville, Colorado. Here, the process of pyrite oxidation at the surface produces acidic water that is gradually neutralized as it drains away from mine waste, depositing a central jarosite zone surrounded by a jarosite + goethite zone, in turn surrounded by a goethite zone with a discontinuous hematite rim zone. Leaching tests show that pH is most acidic in the jarosite and jarosite + goethite zones and is near-neutral in the goethite zone. Measurements indicate that metals leach from minerals and amorphous materials in the jarosite + goethite and jarosite zones at concentrations 10 - 50 times higher than from goethite zone minerals. Goethite zones that fully encircle mine waste may indicate some attenuation of leachate metals and thus reduced metal loading to streams. The potential for impact by acidic drainage is highest where streams intersect the jarosite and jarosite + goethite zones. In these areas, metal-rich acidic dace runoff may flow directly into streams. The U.S. Environmental Protection Agency estimates (U.S. EPA, 1998) that mineral maps made from AVIRIS data at Leadville have accelerated remediation efforts by two years and saved over $2 million in cleanup costs.

Jan 1, 2000

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

7.1 INTRODUCTION Subsidence measurements include surveys of surface and sub- surface movements and measurements and monitoring of surface structural damages. In this chapter the most commonly employed methods are discussed. 7.2 MEASUREMENT OF SURFACE MOVEMENT Surface movements involve two basic components, subsidence and displacement. The other five components (i.e., slope, curvature, strain, twisting, and shearing) are derived from the two basic components. Since all measurements are geometrical, they can be measured by common surveying techniques. 7.2.1 MONUMENTS The first step is to select the types of monuments or surveying stations. Various types of monuments have been employed. The simplest one is a paint mark on the pavement or concrete slab, although this should be discouraged because it is easily affected by artificial or environmental factors. Others use steel or wooden rods, 2 to 3 in. in diameter or square by 2 to 5 ft long, driven all the way down, flush with the ground. Both types of-monuments have no provision for frozen ground heave and both are tampered with easily. A more elaborate type is shown in Fig. 7.1 (O&apos;Rourke et al., 1982). A rebar or iron pipe, 2 in. in diameter by 6 ft long is driven down to nearly flush with ground surface. The top 4-ft section of the hole around the pipe is enlarged to 1 ft in diameter and grouted with concrete. The most sophisticated type of monument is shown in Fig. 7.2 (Conroy and Gyannaty, 1983a). It consists of two hollow steel pipes. The inner I-in. pipe, 10 ft. long is enclosed by a 2-in. pipe at the upper 5-ft. interval. The gap between pipes is filled with foam to isolate the inner pipe from external environmental effects. The bottom of the inner pipe can either remain open or be sealed with a cap, depending on whether the ground is dry or wet. 7.2.2 MONUMENT ARRANGEMENT AND SURVEY LINES The monuments are installed strategically to form survey lines. Three basic types of monument arrangements are shown in Fig. 7.3. Figs. 7.3a and 7.3b are for single and multiple panels respectively; Fig. 7.3~ is mainly for research purposes with multiple survey lines both in longitudinal and transverse directions. This is extremely useful for defining the distributions of ground deformation, as shown in Figs. 2.10 and 2.11. Basically there are two types of survey lines: the whole basin survey line which extends across the panel width or length (e.g., lines R, R, in Fig. 7.3 a&b), and the half basin survey line which covers approximately half of the panel width or length (e.g., lines R, F in Fig. 7.3 &b). Survey lines are generally straight and linear. They should be located on the major crosssections of the subsidence basin. Survey lines must extend beyond the edge of the opening for a sufficient distance so that the edges of the subsidence basin can be determined accurately. The minimum distance from the edge of the opening must be [ ] where h = mining depth, [ ] = angle of draw, and [ ] = 5 to 7 times monument spacing for whole basin surveys, or 8 to 10 times the monument spacing for half basin surveys. There must be at least two controlling monuments at each end of each survey line. Controlling monuments must be located beyond the influence of underground mining. The spacing of the monuments ranges from 15 to 200 ft. The UK National Coal Board (NCB, 1975) recommended a spacing equivalent to 0.20 of the mining depth. Peng and Geng (1982) recommended that the maximum monument spacing be dependent on mining depths as follows:

Jan 1, 1992

By Jorma Miettunen

The Plant. The annual production of the Pyhasalmi mine is 900 000 tons of copper- zinc-pyrite ore containing approximately 0.7 % Cu, 2.5 % Zn and 30 % S. During 1976...1981 altered surface ore, 850 000 tons in all, was also treated at the concentrator. The surface ore was crushed and ground in a separate plant and was then fed into the copper or zinc flotation or was flotated in its own circuit, depending on the degree of alteration and the content of copper and zinc in the ore. The surface ore was exhausted in October 1981. Flotation comprises three consecutive flotation circuits; copper, zinc and pyrite circuit. The zinc circuit includes an open circuit roughing and scavenging. The scavenger concentrate and cleaner tailing are pumped to the middlings flotation. Rougher concentrates of the open circuit and the middlings flotation are pumped to cleaning which includes four stages. Figure 1 describes the flowsheet of the zinc circuit.

Jan 1, 1982

By B. J. Arnold

Coal froth flotation cells typically receive little attention in coal preparation plants. They process only a small portion of the total coal feed (perhaps 5-1 0% of the total plant feed in the United States), they are viewed as a way to take the load off the refuse thickener, and their operation is not well-understood by cleaning plant operators. Operating parameters are set based on the equipment supplier information, and reagent dosages are set at the recommendation of the latest chemical vendor. The cells then operate day in and day out, recovering coal and producing a product that may not meet ash or sulfur specifications or that may be the wrong percent solids for downstream dewatering operations. If improvements can be made to this circuit, then the whole plant will benefit. Paying attention to rate and residence time and the wealth of data from the literature or from a series of targeted laboratory tests can give operators the key to improving the performance of froth flotation cells AND overall plant performance. This paper provides an overview of froth flotation rate and residence time data and gives practical suggestions for specifying and using laboratory tests to improve froth flotation performance. Suggestions for improving froth cell performance are also given based on available literature data.

Jan 1, 1999

By Harold Bloom

The Mount Pleasant Mines, or Mount Pleasant Joint Venture as it is presently known, is located approximately 59.5 km (37 miles) south of Fredericton, NB, Canada. Earliest indications of mineralization were found in 1954, during a regional reconnaissance geochemical stream sediment survey carried out over large parts of New Brunswick and the Gaspé Peninsula. The regional geology of New Brunswick is shown in Fig. 1. This program, sponsored by Selco Exploration Co. Ltd. of Toronto was conducted by H. Bloom, H.E. Hawkes, J.E. Riddell, and J.S. Webb. At its conclusion in 1955, 30 significant anomalous drainages were identified for follow-up evaluation. A total of 4937 sample sites were occupied. Geochemical reconnaissance using stream sediment sampling was a new technique which had only been field tested the previous year in the Gaspé and the northern coastal area of New Brunswick. Sediments collected from known mineralized drainages were found to leave a train of anomalous heavy metals from 1.6 to 9.7 km (1 to 6 miles) in length. When the exercise was extended to a reconnaissance survey, the previously unknown mineralized prospect at Nash Creek, New Brunswick, was discovered, staked, and later drilled (Hawkes and Bloom, 1956). Although it did not come into production, the discovery left little doubt as to the viability of the method and led to the Selco sponsorship of the program for the following two years.

Jan 1, 1991

By Raymond E. Riethmann

El clasificador de espiral fue diseñado originalmente para circuitos cerrados de molienda. Desde entonces se ha aplicado con éxito a otros trabajos de clasificaci6n donde se necesita realizar un corte de dos productos. Inherentemente a las cualidades especiales de este cla- sificador está especialmente preparado para: clasificar, lavar, o agotar materiales tales como minerales, roca fosfática, arenas, carbbn, conchas de ostra y sales fosfáticas. Presentamos ahora las características de operation, flexibilidad de diseiio y líneas maestras para una apropiada aplicación.

Jan 1, 1982

By R. A. Jankowski, J. J. McClelland

Laboratory tests were conducted by the U.S. Bureau of Mines to determine the respirable dust reduction effectiveness of and interaction between face airflow and water sprays for a continuous miner. Exhausting face ventilation was varied from 3,000 to 9,000 cfm (1.42 to 4.25 m3/sec). Spray-water-flow was varied from 15 to 35 gpm (0.057 to 0.132 m3/min), while nozzle operating pressure was varied from 80 to 200 psi (5.62 to 14.06 kg/cm2). Results from gravimetric dust samples indicated that airflow had the greatest individual impact on reducing dust levels, with return and operator concentrations reduced by as much as 57% and 99%, respectively. Interactions between dust control parameters were found to be significant. Often, these interactions defined a level of application for a control parameter where further increases in that parameter failed to produce additional reductions in dust concentrations. In several cases, increases in a control parameter resulted in higher dust levels at the operator&apos;s location. These higher dust levels were attributed to additional rollback and/or airflow turbulence. Regression modeling indicated that increases in airflow to 8,400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.84 kg/cm2) typically were beneficial at the operator and return sampling locations.

Jan 1, 1991

By Don Morris

The Building Products Company is Phoenix based and owned by Mission Clay products of California. Building Products is the only manufacturer of vitrified clay pipe in Arizona. The marketing area includes Arizona, Nevada, Utah, New Mexico, and California. Building Products, promoted by Arizona Public Service, was formed in 1970. Raw-materials prospecting was undertaken for 2 years, after which a $5-million plant was built. Initially, a satisfactory vitrified product could not be made with the raw materials then in hand. Subsequent prospecting and testing led to an acceptable raw-materials mix. Testing to upgrade the final product is a continuing process. The basic raw-materials supply must be adequate, secure, and capable of sustaining close tolerances in the final product. These needs are met by mining four geologic materials at three different localities: (1) refractory aluminous shales (two horizons-one pit) Colorado Plateau Province (Mogollon Rim); (2) less refractory aluminous materials from late Cenozoic lacustrine materials near Dewey in the Transition Zone (TZ); and (3) Precam¬brian "slate" from near New River along the southern edge of the TZ. Other additives include grog (ground-up, broken pipe) and barium carbonate that ties up what gypsum there is. Calcium magnesium carbonates are deleterious components that are minimized by careful selection of the mined products. The raw materials are blended and mixed, ground to 12 mesh, mixed in a pug mill, depleted of air, extruded into pipe ranging from 6 inches to 42 inches in diameter, transported to a hot-air drying room, fork-lifted to an appropriate kiln, and fired at a 1900-2000° F range. The "Rim" kaolinitic shales, being the most refractory ingredient, stabilize the pipe during the firing process. They are very plastic, and therefore facilitate extrusion. The Dewey clay fuses at a low temperature and forms an impervious glasslike binder. It also is plastic. The "slate" forms platy particles that tend to orient themselves during laminar flow. This provides strength for both the green and dried product. It doesn&apos;t absorb water, which helps the drying process. Grog remains stable during firing, and therefore helps to control shrinkage. The development of appropriate raw materials and proper mixtures has been done empirically.

Jan 1, 1987

By William S. Gilmer

INTRODUCTION As man moved through the ages into the era of metals, he became increas¬ingly dependent on the extraction and beneficiation of various ore types. His progression has required more material, new sources, and inevitably, a need to extract the values from ores of much lower yield. Inherently welded to this need to extract has been the attendant requisite of power and water to carry out these tasks. With the richness of these deposits diminished, and the in¬crease of demand, mining has become so intimately tied with the needs of these auxiliary systems that the modern day milling operation can ill afford to ignore them. In the times of Agricola 16th century methods of milling required little thought for power or water consumption. Reduction was accomplished by hand¬sorting and hammer and grinding done with stamps and millstones. Medieval concentration was carried out by the "Jigging sieve" with agitation supplied by the sleeveless arm of the operator (The Mines Magazine,_ March 1933). Little consideration was likely given to the power source unless it became apparent that he had insufficient means to meet the demands of a dawn to dusk operation. Fuel for power production was also probably of little consequence unless sustained drought or warring neighbors burned the miners fields. Water was available from any adjacent stream with recycle, potable, tailings and mill consumption all going and coming from the same source. By the end of the 18th century and the early 19th century the requirements of larger throughputs and better re¬covery were forcing the miner to the need for greater sources of power and water. Arrastras, capable of accepting several hundred pounds of charge, con¬sisted of a clay bottom, a "liner of rocks harder than the substance to be crushed" and a revolving center post in which the ore was ground and amalga¬mated. Used in conjunction with a slucing system, this formed the primary recovery method of the time. Power was supplied by horse or oxen or, if terrain was amenable, by use of a horizontal or overshot water wheel. A typical system required 4.5 kw (6 hp) and needed to run in the vicinity of 15 rpm (Pre¬ston, 1895).

Jan 1, 1986

By James C. Burrows, Frances Kramer Mesher

Tungsten-containing ores are mined on all continents of the world. China is the world&apos;s largest producer and controls the world&apos;s largest reserves. The USSR, itself a sizeable producer, is estimated to be the world&apos;s largest consumer. The major use for tungsten in the noncommunist world is in production of cemented tungsten carbides for cutting, drilling, and wear parts. Other major uses include lamp wires, steels for tools, and armaments. Real tungsten prices have been in a general decline since 1977-1979 as the tungsten market undergoes basic and lasting structural changes.

Jan 1, 1986

By Mark R. Rybak, James Delmonte, Travis Hartman

The City of Phoenix, Arizona designed a 7.2 km (4.5 mi) long water transmission main from the South Mountain Reservoir to the Ahwatukee Foothills Reservoir to address the growing demand for drinking water in the southeast valley. The pipeline design called for a bored tunnel in a very environmentally sensitive area. The Reach3B contract included an 2.44 m (8 ft) diameter TBM excavated tunnel, 1,847 m(6,060 ft) in length. The geotechnical investigation revealed that the tunnel would likely pass through zones of loose to moderately cemented soils (caliche). The primary tunnel support would consist of rock bolts, circular steel ribs, hard wood lagging, and mine straps. A TBM that could handle the ground conditions and allow for efficient ground support installation was required. This paper describes the construction of a small diameter rock tunnel in challenging ground conditions.

Jan 1, 2003

By K. B. C. Brady, B. E. Scheetz, J. E. Cuddeback, T. W. Bergstresser, W. A. Telliard, S. C. Parsons, R. J. Hornberger

Two weathering procedures are being developed by the Acid Drainage Technology Initiative in cooperation with federal agencies(OSM and EPA). Objects are to: (1) standardize existing humidity cell and leaching column procedures; (2) improve test methods by maintaining a carbon dioxide enriched environment needed to optimize carbonate mineral dissolution, and quantifying particle size variables to evaluate reaction kinetics, and (3) provide flexibility in test method implementation consistent with EPA guidelines for Performance-Based Measurement Systems. Preliminary results indicate the CO2enriched leaching environments produce alkalinities that are similar to field observations and greater than the tests run under atmospheric PCO2. Leaching columns produce higher alkalinity than humidity cells.

Jan 1, 2003