Search Documents

By Michael Li

Unsaturated flow and solute transport were studied in three large columns measuring 1.5 m diameter x 2 m height, loaded with up to 3.7 t of oxidised waste rock, which was excavated from the Stratmat pile at Heath Steele Division, Noranda Inc. and contained elevated concentrations of zinc in the pore water. The bottom of each column was partitioned into 37 squares, each of which was drained independently. Following rain simulations at the top of the rock bed, the drainage in each drain port was monitored for volume and physicochemical parameters at pre-determined intervals. This paper describes some of the observations resulting from the experiments. The main conclusion of the study is that unsaturated flows in waste rock are heterogeneous, and flow channelling is ubiquitous. The results imply that the transport of solutes from oxidised waste rock to its toe drainage is subject to various controlling mechanisms, including geochemical equilibrium control and successive pore water dilution control.

Jan 1, 2000

By T. Negeri, A. O. Orumwense

Microwave pretreatment is one of the emerging technologies which have been reported as having potential economic benefits for the processing of amenable ores. The application of microwave pretreatment to the processing of refractory and finely disseminated ores is of great interest as the technology can potentially reduce high comminution costs and improve mineral liberation. Sized ore samples were subjected to microwave irradiation at power levels varying from 1 to 5 kW over exposure times of between 1 and 6minutes in order to determine the influence of heating rate on mineral transformation, ground product size distribution and mineral liberation. The microwave irradiated samples were ground and subsequently floated. A comparison is made with non-microwave treated samples. Flotation grade and recovery show a strong dependence on the microwave absorption characteristics of the mineral components of the ore, in the following decreasing order -sphalerite, galena, and lastly chalcopyrite.

Jan 1, 2003

By R. L. Grayson, S. S. Peng

Sampling of respirable dust and analyses of samples have been partially completed for a longwall panel. Physical and compositional properties which have been characterized include: 1. Respirable mass concentration, 2. Mineral composition, 3. Particle size distribution by mineral, 4. Particle shape distribution by mineral, 5. Particle angularity distribution by mineral, and 6. Respirable size distribution. Analytical techniques used in the characterization of samples are described, and results are reported with emphasis placed on relationships between the various characteristics and worker locations. Details of existing mining conditions, equipment arrangements, dust control methods and operating system parameters are presented.

Jan 1, 1986

By V. K. Karra

An improvement in the present day screen sizing methods calls for knowledge on i) how material in the size range: 0.5 x 1.5 times the through-fall opening of the mesh on a deck, splits between the oversize and undersize streams of the deck, and ii) how near-mesh content of the feed affects the screening performance. In the throughput based sizing method given here, this is accomplished through the introduction of a generalized partition curve and a near-mesh factor. A newly developed efficiency factor is employed in addition to the traditional screen sizing factors.

Jan 1, 1979

By James R. Piper

Cumulophyric feldspars, of varying morphology, carry myrmekitic quartz interstitially between microperthitic feldspar lamellae. The size, coarseness, and morphology of these crystals, together with concordant foliation features constitutes evidence that they are a product of primary crystallization, formed prior to eruption from a vent. These crystals occur preferentially along 2 - 5 mm thick tan, vesicular to compressed alteration bands intercalated with more densely welded light grey bands. In perlite with quartz at or below a 0.1% threshold, megascopic feldspars are less than 1%. Perlite with quartz above this level has megascopic feldspar concentrations >3%, typically in the 5-20% range.

Jan 1, 1991

By J. E. Gebhardt, L. Piga, G. Schena

The possibility of beneficiating a low-grade alunite ore from the Tuscany region of Italy was examined. Flocculation and flotation techniques were investigated to separate alunite and kaolinite from the ore, which also contained feldspar and quartz. Flotation was performed at pH 6.5 with oleic acid as collector and sodium silicate as dispersant. A concentrate containing 12% alunite with a recovery of about 65% and a concentrate containing 28% alunite with a recovery of 84% were achieved from the -38-µm feed samples containing 5.0% and 12.9% alunite, respectively. Poor recovery of alunite was achieved by flocculation methods.

Jan 1, 1999

By M. Kaya

The main purpose of this study was to design a modular/mobile coal preparation plant with a capacity of 300 t/h for Seyitömer B3 vein (almost 70% of the whole SLI deposit). Firstly, coal washing properties and washability curves were determined by sink and float tests. Then, equipment sizing, selection, flow sheet development, economic evaluation, investment and operating costs were determined for coarse (-150+18mm), fine (-18+0.5mm) and slime (-0.5+0.1mm) coals. Economic evaluation of the proposed flow sheet showed the feasibility and profitability of the investment.

Jan 1, 2006

By William C. Beebe, Russell E. Martin

An account of driving and concreting two 900 m railroad tunnels for the Denver and Rio Grande Western Railroad under emergency conditions. Details the importance of on-site decision making by the Owner in completing the project successfully in record time. A general description of the geology and construction methods. The Thistle Drainage Tunnel drained water impounded behind the Thistle slide and serves as permanent diversion of the Spanish Fork River and Thistle Creek around the slide area. The project involved 684 meters of 5 m horseshoe tunnel, a 5 m diameter raised shaft and 23,000 cm of cut excavation.

Jan 1, 1985

By Jim Morris

This paper will describe the excavation of a 5.4 percent decline at the Montanore Project for Noranda Minerals Corporation. The 5.3 m by 4.9 m tunnel was driven to provide access for the exploration of a major copper-silver deposit. Soft ground and conventional drill-blast mining were used on the 4,270 m tunnel. Ground support consisted of steel sets and concrete in the soft ground and pattern rockbolts providing the majority of the rock support. A special feature of the project was the use of conveyor haulage in conjunction with the drill-blast excavation.

Jan 1, 1993

By Gao Zhizhong, Zheng Shibo, Gu Zhengxing

Extensive research on the beneficiation of Florida dolomitic phosphate pebble has been carried out by Lianyungang Design and Research Institute of China (CLDRI) in recent years. Test results indicate that the fine-particle flotation process could be used to effectively recover the phosphate values from Florida high-dolomite phosphate resources. With the CLDRI fine-particle flotation technology, a phosphate concentrate with 31% P2O5 and less than 1% MgO could be obtained from a flotation feed containing 25.8% P2O2 and 2.2% MgO at an overall P2O5 recovery of up to 85%.

Jan 1, 1999

By W. Dalmijn, H. de Ruiter

"The decline in students for mining and metallurgical engineering in the last few years has lead to the closure of many university departments in all first world countries around the world. Three independent studies carried out in Europe, Australia and North America indicate that during the next decade the demand for mining, minerals processing and metallurgical engineers will be significantly higher than the supply. Demand for engineers will increase even more because many of the professionals in industry are about to retire within the next 5 years. Meanwhile mining is a growth industry, minerals demand continues to increase in line with the growth in World GDP, as illustrated in the Graph at the end of the paper."

Jan 1, 2005

By Keith E. Dyas, John Nelson, Ronald T. Johnson

GENERAL DESCRIPTION The Bruce mine of Cyprus Mines Corp. is located in Bagdad, AZ. The mining method used is open cut-and-fill. Of the annual production of 81 647 t (90,000 st), approximately 83% is taken from load-haul-dump (LHD) stopes and the balance from slusher stopes. All ore is produced from the area between the 1250 level and the 2300 level. The average travel time from the shaft pocket to the stope is approximately 5 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip The Bruce ore body occurs in quartz-sericite schist with Dick rhyolite on the footwall and andesite on the hanging wall. Diabase dikes are found in the hanging wall; there is also a dike coming off the footwall and crosscutting the ore body. All of the rock types are of the Precambrian Yavapai series and have been subjected to regional metamorphism. A composite of the ore body is given in Fig. 1. The deposit is of massive sulfides occurring as a steeply dipping replacement body. On the upper levels the ore is veinlike with widths from 0.6 to 4.6 m (2 to 15 ft), dipping at 1.4 to 1.5 rad (80° to 85°). On the lower levels the ore is dipping from I to 1.2 rad (60° to 70°) with widths from 3 to 16.8 m (10 to 55 ft). The strike length varies between 107 to 183 m (350 to 600 ft). The rhyolite footwall generally has a knife-edge contact with the massive sulfides. The exceptions to this are the upper levels where there is a 1.5 to 3 m (5 to 10 ft) band of silicified sericite schist between the sulfides and the rhyolite. In the southern part of the ore body the hanging wall is tuffaceous andesite and andesite. In this area the contact is generally sharp and easy to follow. However, to the north there is a large chlorite schist zone that crosscuts the bedding and comes in contact with the massive sulfides. This is apparently due to hydrothermal alteration of the andesite. The chlorite schist is highly mineralized with chalcopyrite and pyrite and quite often forms economic pockets of ore. In the massive sulfides the chief ore minerals are sphalerite and chalcopyrite. Pyrite is the predominant sulfide with considerable pyrrhotite throughout. Bright arsenopyrite ouhedrons in fine grain massive sulfides are quite common. Occasionally small amounts of galena are seen, usually near the foot or hanging wall contacts. On rare occasions tennanite is associated with massive arsenopyrite. Minor amounts of quartz, calcite, and un¬replaced remnants of sericite schist occur, but essentially pyrite is the gangue in which the ore minerals occur. The ore values are in excess of 3.5% copper and 12.5% zinc with some silver and rare gold as byproducts. Ground Conditions The massive sulfides are generally self-supporting. One exception is in the 1850 stope where the ore body is 9 to 11 m (30 to 55 ft) wide and 152 m (500 ft) long. There are flat to shallow dipping slips and seams in the ore, creating extremely blocky ground. For support, old 25.4-mm (1-in.) hoist ropes were installed tensioned to 27 t (30 st), and then cement grouted over the entire length in longholes [14 to 15 in (40 to 50 ft) in length) drilled on 3-m (10-ft) centers from the level above. This has tied the formation together very successfully and virtually eliminated the blocky ground condition. Both the hanging wall and footwall are quite shaley in some areas. Reasons for Adopting Trackless Open Cut-and-Fill Methods First, any method other than open cut-and-fill would have caused too much dilution. The use of rubber-tired mining equipment in the pro¬duction stopes requires a footwall ramp. The inclines in ore will be mined out, so this ramp in the footwall will provide access to and from the stopes (Fig. 2). This incline is very expensive, but necessary to convert existing stopes to LHD mining. 'The final cost of ore mined by the LHD machines has not been determined. As of 1972, tons per manshift in the 2150 stope-the only one to complete a full cut-had increased from 7.58 t (8.36 st) to 12.83 t (14.14

Jan 1, 1982

By A. L. DeVegt, H. G. Bayer, C. J. Buisman

During the last ten years, Paques Inc. has been engaged in the development and installation of treatment systems to remove sulfur compounds from water and gaseous streams using biotechnological processes. Metal and sulfate can be removed from mine waters in two biological steps. In the first step, sulfate-reducing bacteria converts sulfate to hydrogen sulfide (H2S). The HS reacts with the dissolved metals to form insoluble metal sulfide precipitates. In the second step, sulfide-oxidizing bacteria convert excess H2S to elemental sulfur. The Budelco Zinc Refinery in The Netherlands installed a groundwater treatment system to remove metals and sulfate using the biological steps described above. The system has been operating since May 1992 and has been treating 5,000 m3/d (180 thousand cu ft/day). A pilot plant began operation in November 1995 at Kennecott's Bingham Canyon Utah copper mine to develop processes for metal and sulfate removal from groundwater and for the selective copper recovery from leach water. The principle of the biotechnological methods, the full-scale experience and an overview of the test program at the mine are presented

Jan 1, 1999

By Rick McGregor, David Blowes, Mike Choi, Ralph Ludwig

The oxidation of sulfide minerals at an ore transfer location in Western Canada has resulted in widespread contamination of underlying soil and groundwater. The oxidation of sulfide minerals has released sulfate [SO,] and heavy metals including cadmium [Cd], copper [Cu], nickel [Ni], lead [Pb], and zinc [Zn] into the groundwater. A compost-based sulfate-reducing reactive wall was installed in the path of the plume in an attempt to reduce the potential impact of the heavy metals on a down-gradient marine inlet. Monitoring of the reactive wall over a 21-month period has shown that Cu concentrations decrease from over 4000 ug/L to less than 5 ug/L. Cadmium, Ni, Pb, and Zn concentrations also show similar decreases with treated concentrations generally being observed near or below detection limits.

Jan 1, 2000

Liebherr Mining Equipment Co., of Newport News, VA and Baxter Springs, KS, introduced the T282, a new two-axle, diesel-electric, AC drive haul truck with a payload capacity of 327-t (360-st). The T282 was unveiled at a press briefing in October 1998 at the company's Baxter Springs research and development1 manufacturing facility. In addition to an increase in pay- load capacity, the truck's AC drive system has been de- signed to allow for easy configuration to a trolley-assist system with minimal additional equipment. The T282 provides fuel savings, reduced maintenance requirements, and reduced downtime and maintenance costs, providing the mine operator with increases in productivity. Basic dimensions and weight of the T282 are: ? Overall length, 14.5 m (47.5 ft). ? Overall width, 8.7 m (28.7 ft). ? Loading height, 6.5 m (21.2 ft). ? Height - body up, 13.9 m (45.9 ft). ? Empty vehicle weight, 201 t (221 st). ? Operating weight - loaded, 528.6 t (582.6 st). ?Engine, Detroit Diesel 16V4000 at 2 MW (2,750 hp). ?Electric drive system, Siemens/Liebherr.

Jan 1, 1999

By J. G. Groppo, B. K. Parekh

A series of performance studies were conducted using countercurrent column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia using a 150-mm (6-in.) inside diameter column that was 5.8 m (19 ft) high. Both thickener feed and classifying cyclone overflow with a typical size distribution of 150 µm (100 mesh) X 0 were tested. The percent solids of the column flotation feed varied from 1.5% to 15% while the ash content ranged from about 30% to 60%. The concentrates produced contained 2% to 10% ash with Btu recoveries of nearly 90% using 0.12 to 1.25 kg/t (0.25 to 2.5 lbs per st) fuel oil and 0.12 kg/t (0.25 lbs per st) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from seven different seams are discussed as well as scale-up relationships used to design a full-scale installation presently in operation.

Jan 1, 1991

By Bekta? Uz

In this research, geological characteristics of sand quarries around the village, Kemerburgaz Akpinar, are studied and the mineralogical, petrographical, chemical and technological characteristics (such as sieve analysis, relative density, water absorbtion etc.) of the sand samples, obtained from the area are explained. In the general area sand' quarries, being in lacustrine formations belonging to Neogen, the stratigraphic location of the sand occurences take place at high levels of these formations, geologically. All of this pattern, being under 1 mm with a ,particle dimension, it ranges from 0,5 mm in the quantity of 99 % to 0,25 mm in the quantity of 15 relative density is 2,65 g/cm3 ; water absorbtion is 0,9%. Mineralogically, the sand samples contain Quartz (84%), Feldspar (3%), Calcite + Aragonite (10%), Pyroxen+Amphibole (1-2%), Garnet+Tourmaline (0.5%), Olivine (0.1-0.5%). Besides, sand samples contain SiO2 with the quantity of above 90%. Containing Quartz at high levels for mineralogical, petrographical and chemical characteristics, Akpinar sand will be evaluated as silica sand when the carbonate mineral is removed with the method of ore preparation such as leaching.

Jan 1, 2005

By L. R. Nelson

Cyprus Pima is a medium-sized open-pit copper mine located 35 km (22 miles) south of Tucson, AZ. The ore body was discovered using geophysical prospecting methods in 1953 and was originally worked as a small underground mine followed by small open-pit operations. As mining equipment grew larger and the economic ore grade dropped, the operation grew in size, through four expansions, to the present 50 500 tpd (56 500 stpd) milling rate. The remaining stripping ratio is about 2.5 to 1. Mining equipment includes 11 electric shovels ranging in size from 6 to 15 m3 (8 to 20 cu yd) and 42 diesel-electric haulage trucks ranging in size from 89 to 223 t (100 to 250 st). Mine planning is performed at Cyprus Pima to serve several functions. The most important is to plan ahead, one year at a time, to predict the ore grade and stripping requirements on a month-by-month schedule. This yearly plan is necessary for budget preparation and is revised once each quarter to incorporate variations in actual production experienced during the preceding quarter.

Jan 1, 1979

By M. T. Ityokurnbul, M. P. Trubelja

Concentrate flow rates were measured for the flotation of -100-mesh Lower Kittaning coal in a computer-controlled 0.076 x 3.5-m pilot flotation column. The variables studied were recovery zone height, airflow and solid feed rates. The specific projected surface areas of the feed, concentrate and tailing streams were determined from the measured particle size distributions. The results obtained show that the concen¬trate flow rate was independent of recovery zone height but was dependent on the hydrostatic pressure setting (measure of froth depth), gas flow rate, solid loading and particle size. New correlations for column carrying capacity and yield are provided as a function of bubble surface area flux and the specific particle projected surface area.

Jan 1, 1999

By Frank E. Kottlowski

Widespread high-calcium (HC) limestones in New Mexico and adjoining areas, are low in magnesium, but some units include shale interbeds that would be deleterious for usage in sulfur removal. In southwest New Mexico, southeast Arizona, and adjoining parts of Mexico, limestones in the thick Mississippian Escabrosa, Pennsylvanian-Permian Horquilla, and Cretaceous U-Bar units are HC as are strata in the Mississippian Lake Valley, Pennsylvanian formations, Permian Hueco, and parts of the Permian Capitan Limestone of south-central and southeast New Mexico and west Texas. In north-central and central New Mexico, many limestones in the Pennsylvanian Madera Formation are HC as are some of the Cenozoic travertines. In northwest New Mexico, where the present-day mine-mouth coal- fired power plants occur, there are no HC limestones, but to the north in southwest Colorado some beds of the Mississippian Leadville Limestone and Pennsylvanian Hermosa Formations are HC. HC limestones considered contain at least 95 percent calcium carbonate and less than 3 to 5 percent magnesium carbonate. Limits for other impurities are alumina, 1 percent; silica, 2 percent; sulfur 0.05 percent; phosphorous, 0.02 percent; and iron oxide, about 1 percent. Chemical and physical requirements differ slightly depending upon the ultimate use.

Jan 1, 1995