Search Documents

By E. D. Thompson, Y. J. Zhang, K. F. Unrug

This paper presents the results of a recent study on the development of an in situ testing method for determining coal strength in mine pillars. The strength testing is performed in the horizontal holes drilled into the coal rib using a penetrometer, which is an hydraulically powered device that uses an indenter to press on the surface of the borehole until the load reaches the failure point of the coal. The pressure and the penetration of the loading pin are recorded by a data-acquisition unit. The results collected from several coal mines indicate that this testing method is ideally suited for the realistic coal strength measurements. The new testing system not only improves the accuracy of the pillar-strength determination, but it is more cost efficient than the conventional method.

Jan 1, 1997

By J. Partyka

Fumes produced during blasting operations in underground mines are defined in this paper by an equivalent contaminant source. The primary goal is to establish a method which would allow all those parameters not measured directly to be determined reliably from field data. The parameters to be identified are the diffusion coefficient , and the position and size of an equivalent source. The diffusion-value is computed from the peak concentrations taken by two monitors located in the drift. The first monitor is placed close to where blasting pollutants join the main stream, while a second monitors is moved downstream a some distance from the first point. The position and size of the dust source and the total amount of dust produced during blasting are determined from the data recorded by only one monitor.

Jan 1, 1991

By Gary Schaffer, Anthony Stentz

Surveying of mines is a necessary step in coal mining to assemble maps which are used for tracking progress in the development of the mine and to plan future coal removal. A first approach for automatically building high-resolution two-dimensioml maps of underground coal mines is presented. The technique assembles laser rangefinder scans obtained from several locations within the mine into a consistent global map of the mine. Each range scan comprises thousands of data points collected in one second, thereby achieving higher resolution and much faster measurement compared to a human using a transit. The raw data (range scans) are processed to fuse them into a consistent representation. This paper describes a first approach to automated surveying and presents initial results of merging range scans. Improvements to the scan-merging algorithm are proposed.

Jan 1, 1993

By Donald Ross-Watt

Mining project investment concerns the installation of mine capacity for the purpose of generating a stream of future economic benefits. In order to make this type of investment decision, the optimum specifications for the project must first be determined. Then, the economic justification of the investment tin be evaluated based on these specifications. Economic evaluation to guide mining project investment decisions is based on a proposed plan for mining the deposit over its operational life. If single point estimates are made of deposit characteristics and environmental parameters* as the basis for assessing a future stream of economic benefits associated with the investment, a future mining-plan can be optimally fitted to these estimates and, to the extent that such estimates are actually realized, this plan will retain optimality.

Jan 1, 1979

By Kendrick C. Hardcastle

Although the basic techniques employed in hydraulic pumping in open pit mining have been practiced throughout the better part of this century, only relatively recently have studies of' sufficient depth and scope been conducted to improve these techniques. This paper will point out the basic techniques involved and some of the more recently discovered data concerning hydraulic pumping, Inherent in all hydraulic transportation systems apart from the consideration of transportation cast, is the outstanding advantage of slurrying the matrix at the mining pit so as to provide a lengthy and thorough soaking and washing of the material while in the pipe line and thereby reduce the necessity for washing, scrubbing and other treatment in the beneficiation plant. This is quite important in view of the constant increase in demand for a cleaner product.

Jan 1, 1964

By Edward C. Heistermann

The Falkirk Mining Company, a wholly owned subsidiary of The North American Coal Corporation, is located 80 kilometers (50 miles) north of Bismarck, North Dakota. Falkirk is under contract to provide 5.08 mil- lion tonnes (5.6 million short tons) annually to the Coal Creek Generating Station, an 1100 mega- watt electric plant owned by the Cooperative and United Power Associations of Minnesota. Coal Creek is located 2.4 kilometers (1 ½ miles) south of the Mine. Electricity from the plant is transmitted to rural electric customers in Minnesota via a 400-kilovolt D.C. power line.

Jan 1, 1982

By B. Catalano, D. Ifrim

The Annacis Island Outfall Project includes two TBM bored tunnels with face pressures above 3.5 bar, with an internal diameter of 4.2 metres. This paper discusses the innovative approach to TBM tunnelling and TBM design at the Annacis Outfall Project. The TBM custom design includes a 3.6 m OD core machine manufactured by Herrenknecht and a 5.0 m add-on by the Contractor (Bessac), acting as an extension kit, with optimized gantry design to accommodate for short tunnel drives and quicker launches. This novel design approach produced safety improvement, cost and schedule savings while streamlining logistics of TBM retrieval.

Dec 1, 2022

By G. T. Lineberry, R. Q. Honaker

Coal extraction typically results in the recovery of pure rock that ranges from small to very large quantities depending on seam thickness and other characteristics. The removal of pure rock may allow the recovery of three times the amount in middling coal particles, which has significant economical benefits. In an industrial example, a 150% increase in revenue was realized from deshaling a low-ash, run-of-mine coal and blending with a processed clean coal product. Deshaling is the process of removing pure rock from coal, which normally involves a high-density separation in a gravity-based process. The removal of the relatively pure rock near the point of extraction has the potential to further enhance the economics of an operation due to reduced materials handling and refuse storage costs.

Jan 1, 2004

By Robert H. Scott

Developments during the past few years have brought coal-based composite fuels to commercial readiness. During the next few years, composite fuels will become available from a number of suppliers. Potential users must evaluate the combustion properties of these fuels to determine equipment and operating changes required for their use. Most work to date has been done with boiler applications. However, many potential non-boiler applications exist in the metals and minerals industry. These applications require specific evaluations appropriate for the processes involved.

Jan 1, 1982

By Alfredo Menendez, Alberto Sarmentero

A B S T R A C T The Los Pijiguaos bauxite is one of the largest accumulations of trihydrate alumina ore recently discovered; it is a plateau type, with no overburden, relatively soft tertiary quartz-bearing bauxite developed on a pre-Cambrian Rapakivi Granite batholith. The deposits are found in the northwestern rim of the Guiana Shield, State of Bolivar, Venezuela, and were discovered in 1976 after a grass-roots exploration campaign. Target areas were mainly selected on the basis of geological and geo¬morpholigcal criteria, guided by correlation with known deposits elsewhere in the Guiana Shield. The vertical. lateritic profile consists of an upper concretionary zone, followed by a mottled zone, a palid zone and finally the weathered rock merging into fresh granite. The upper concretionary zone displays a cellular, pisolitic or spongy texture and contains the following minerals: gibbsite (60-90%),quartz (5-10%), hematite (5-10%), goethite (under 5%), boehmite (traces), kaolinite (traces). The gibbsite content decreases sharply downward from the lower limit of the concretionary zone and the kaolinite and quartz content increases in the underlying mottled zone. The mottled and palid zones display a pseudo rapakivi texture and quartz, kaolinite and mica are the. essential minerals.

Jan 1, 1984

By A. Gene Collins

The demand for lithium may increase because of its potential use id lithium batteries and in the generation of electrical power by fusion. Therefore, lithium abundance in some United States oil-field brines was surveyed. Oil-field brines from numerous locations were found to contain more than 100 mg/l lithium and several exceeded 500 mg/l. An area of 25,000 km2, with a reservoir thickness of 60 m, an effective porosity of 5 percent, and a brine with a specific gravity of 1.2 containing 100 mg/l of lithium, contains about 0.75 x 106 tonnes (1 tonne = 1 metric ton = 1,000 kg) of lithium in 7.5 km3 of brine. It is postulated that the brines were enriched in lithium by lithium-rich spring water or lithium leached from volcanic rocks followed by evaporation sequences.

Jan 1, 1978

By D. A. Peterson

Laboratory testing was completed to determine the effectiveness of a fiberglass cable bolt (FCB) as a cuttable rock support for a continuous, hard-rock mining method. The FCB consists of four Polystal tendons combined in a node/antinode fashion, with polyvinyl chloride (PVC) spacers forming the anti-nodes. The largest ultimate pull-out load achieved by the FCB was 22 t (48,400 lb) at 89% of the tendons' theoretical pullout load. This premature tendon failure is accredited to: • differential stresses within the tendons and • differential tendon displacement. An increase in pull-out resistance for a given embedment length is due to: • increased bond area, • reduced interfacial shear and • "wedge" effect. The critical embedment length was found to be 40% less than for conventional steel cable bolts (SCB) at a 127-mm (5-in.) node spacing. An FCB can have up to a 92% increase in load-carrying capacity over a conventional SCB at equal embedment lengths. The load carrying capacity is equivalent to SCB at a 960-mm (37.8-in.) embedment length. Though the FCB is 7.5% more expensive than the conventional SCB (installed), this cost may be offset by increased performance. FCBs are a potentially viable support alternative for continuous hard-rock mining.

Jan 1, 1993

By L. Eros, R. H. King

The US Bureau of Mines has funded several research and development projects in computerized mine monitoring and control. Hardware and software components have been sufficiently developed so that mine operators have been provided with an efficient means to comply with federal regulations and increase mine safety. Several cost benefits have been realized as well, particularly with increased conveyor belt haulage availability. Western Fuels-Utah Inc. approached the Bureau to assist in planning, installing, and evaluating a computerized mine monitoring and control system because of the agency's research experience in this area. The installation was planned for Western Fuel's Deserado mine, located in Rangely, CO. Since a large, complex, underground mine producing about 2.4 Mt/a (2.7 million stpy) of coal was projected, the company anticipated significant benefits in safety and efficiency through a computerized monitoring and control system. A major part of the cooperative program was to document and evaluate the system design, installation, and operation. This will assist others to adequately design, specify, install, and operate future systems. Mine description The Deserado mine plan and layout have important impacts on the monitoring system requirements. Long range plans are to produce 2.4 Mt (2.7 million st) of clean coal annually from two longwall sections and four continuous sections. Presently, two continuous miner sections operate under 213 m (700 ft) of overburden in the 2.3 to 2.5 m (7.5 to 8.5 ft) thick D seam to develop main, submain, and panel entries have developed for a longwall. These began operation in December 1986. Belt conveyors haul the coal from the mining sections to a 1.4-m (54-in.) belt located in the upper compartment of the slope. The lower compartment contains a hoist for men and material transport. From the slope, the coal moves to two 9 kt (10,000 st) raw coal storage silos, then to a 680-t/h (750-stph) preparation plant. After cleaning, a 5.5-km (3.5-mile) overland conveyor carries the coal to a clean coal slot storage and rail load-out facility. An electric locomotive then transports the coal to the Bonanza Power Plant in Utah. Allen-Bradley monitoring and control hardware and software controls the preparation plant, with two PLC-3 programmable controllers and a Process Control Industries D-1200 color graphics interface. The system operator uses three "smart" color video display units and an alarm printer for hard copy records. Originally, it also monitored and controlled the conveyors from the bottom of the slope to the top of the raw coal silos, the preparation plant, the overland conveyors, the main mine ventilation fan, and the hoist. Some of these features, though, were later transferred to the mine system.

Jan 2, 1988

By Hugh E. Cronin, Joseph J. Coluccio

The Columbia Slough Consolidation Conduit Project is a 12 ft. 0 in. inside diameter—15 ft. 4 in. excavated diameter tunnel, 8,300 lf. in length. The tunnel is divided in two parts a 4,460 lf. reach to the West and a 3,770 lf. reach to the East separated by a flow regulation structure in the middle. The project was built for the City of Portland, Oregon Bureau of Environmental Services (BES) by the Frank Coluccio Construction Company (FCCC) Seattle, Washington under a $22,600,000.00 contract starting in 1998 and completing the contract in 2000 at a total cost to the City of $25,448,000. An increase of 12.6% from the original contract. The tunnel was constructed in an alluvial sediment that ranges up to 1,500 feet thick. The sediment varies from ?ne silty sand and sandy silt (SM-ML) to coarse sand and gravel (GP-GM) with varying quantities of cobbles and boulders. Most of the tunnel was constructed above the water table although one reach of almost 1,000 lf. had water to above the tunnel crown. The contractor, FCCC, used a Lovat 15 ft. 3 in.900 hp shielded TBM with multiple doors (4) of variable opening to excavate and support the tunnel. Tunnel supports were 5 in. WF 16 lbs. per foot at 4 ft. spacing and4 in. Douglas Fir lagging. Tunnel excavation was worked in 10 hour shifts with additional equipment maintenance and repair on the off time. The original Geotechnical Design Summary Report (GDSR) established a baseline for contractual purposes of slightly over 5 boulders (between 12 in. and48 in.) per foot of tunnel. (Table 1) At the pre-bid conference, three test pits were excavated to approximately tunnel invert, one at each end of the project and one in the middle near the flow regulation structure. The test pits encountered a few boulders but did not seem to support the five boulders per foot (varied from one boulder per foot of tunnel to eight b/lf.). Subsequent to the pre-bid meeting and the test pits, BES issued any addenda which changed the baseline boulder quantity in the GDSR to 1.7 boulders per foot of tunnel (varied from0.2 to 3.5 boulders per foot) a reduction of 67% from the original baseline. It is interesting to note the two separate tunnel reaches and how they were evaluated in the GDSR. Originally the Eastern portion of the work was projected at5.08 boulders per foot of tunnel and the Western portion at 5.30 boulders per foot of tunnel for a variance of less than 5%. In the revised quantity the Eastern portion was projected at 2.01 boulders per foot of tunnel and the Western portion at 1.42 boulders

Jan 1, 2003

By T. L. Conley, J. J. Rozek

The $2 billion (A$) Melbourne City Link Project is one of the largest and most important metropolitan road developments ever undertaken in Australia. The project involves two three-lane vehicular tunnels totaling 5 km, constructed as deep as 65 m underground. The 3.4 km Burnley tunnel is one of the world's longest three-lane tunnels. The project is being delivered under a DBOOT [design-build-own-operate-transfer] process and all design and construction is performed to ISO 9000 standards. Tunnel excavation began in May 1996, and the tunnel will open to traffic in 1999. This paper focuses on the range of construction techniques utilized during construction.

Jan 1, 1999

By J. Ainsworth, W. Trudel, L. Schutz, C. L. Bolin

Newmont mine geologists have added substantial economic value developing over 1,150 tonnes into quality surface and underground gold reserves since 1986. However, the recent 5-year gold price slump from $387 to $262 per ounce has shifted mine geologists focus to optimizing open pit profitability and developing high-grade, high cash flow and low capital development underground reserves. More than $65 million projected revenue has been added to the Gold Quarry south layback following multi-departmental model reconciliation investigations. Kriged mine polygon construction, controlled blast heave and high-quality geologic advice in selective mining will have multi-million dollar beneficial impacts.

Jan 1, 2002

By B. S. Crocker

Introduction Pebble mill grinding can be defined as wet or dry grinding in a tumbling mill with pebbles used as grinding media instead of metal balls. To clarify the terminology, which may differ in the various mineral industries, it is essential to point out the differences between grinding with partially sized and carefully sized grinding media. When grinding with partially sized media (limited top size only), sizing is usually the setting of the primary crusher and there is no bottom sizing-all fines, chips, sand, and small sizes are included. This is often called run-of-mine or primary autogenous grinding. In this case the entire crusher discharge is fed into the mill and part of it becomes "charge" and the rest is "sand feed." When grinding with carefully sized media (i.e., media that is sized both at the top and bottom of the size range), no fines or chips should be present in the charge to the mill. This is pebble milling and the grinding media consists of ore, rock, Danish pebbles, gravel pebbles, or ceramic pebbles-media that is appreciably lighter than steel balls. The grind¬ing charge is fed to the mill to maintain a load and it does the grinding usually on a classified sand product of suitable size. If the grinding media is the same as the raw material being ground, this type of grinding is also called secondary autogenous grinding. Pebble milling was in common use in the gold mines of South Africa in the early 1900s. It is by far the oldest form of autogenous grinding. It may be used to grind crushed ores from a maximum size of about -% in. to all -10 µm. Pebble milling differs from "run of mine" grinding in many ways, but two big differences are: I) The ore itself is crushed to approximately t/4 in., or it may be further reduced to 8 or 10 mesh in a rod mill or fine crusher. 2) Then carefully screened ore of the correct size is placed in one or more stages of pebble mills to grind the ore to its desired final size. The media size is carefully selected to be the most efficient for the particular size reduction required in each stage. This is a precise practice, and pebble mills can be designed as easily and accu¬rately as can rod mills or ball mills by those skilled in the art. A pebble mill is a rotating cylinder in which the grinding media has been carefully sized for the job in hand. If the mill is doing coarse grinding, the media will be correspondingly large and the mill might be called a primary (or intermediate) pebble mill or a lump mill. If it is to do fine grinding, the media selected is proportionately smaller and the mill would be called a secondary or tertiary pebble mill. The media itself is normally rounded pebbles made from screened ore from the primary-crusher discharge. The charge could be rounded pebbles of the correct size removed from a primary autogenous mill, or the pebbles could be carefully sized gravel, sized beach pebbles, or sized flint pebbles. Usually the specific gravity of a pebble is from 35 to 55% of that of steel balls. It commonly varies from 2.66 to 4.2, depending on the specific gravity of the ore. Primary pebble mills, or lump mills, would be charged with pieces of rock up to 10 in. maximum and 5 in. minimum and would grind crusher discharge with a maximum size of 1/4 in. on hard ores and 3/8 in. on softer ores. Secondary pebble mills could be charged with pieces of rock screened on 4 x 4-in. square mesh and retained on 1 1/2 x 1 1/2 in. These mills would grind material with a top size of 8 to 10 mesh. Tertiary pebble mills could be charged with screened rock that would pass 3 x 3 in. and be retained on 1 x 1 in. and grind 35 to 48 mesh sands. Principles of Operation Media Size To operate a pebble mill efficiently it is imperative that great care be taken in screening the rock feed that is fed into the mill to round up into a range of pebble sizes that are suitable for grinding of the sands that are also being fed into the mill, having regard to the top size and the average size of such sands. Since most mill operators know from experience the correct size of steel balls to be used in a mill to handle different sizes of sand feed, it is convenient to relate the pebble size to a ball size. If the correct ball size is not known, it is relatively simple to conduct batch laboratory tests in 12- to 18-in. laboratory mills to determine the optimum size of steel ball. Also, Bond and others have published formulas for calculating the optimum ball size. When the correct size of the individual steel ball is known, then a pebble of the same weight will perform the same grinding if used in the proper size of mill and under the proper conditions, which will be defined later. This media size, as defined by the average weight of the individual pieces, is most important. The following tests will serve to clarify this point. Laboratory Tests Using Steel Balls or Pebbles. Several labora¬tory grinds were made to compare a given size and weight of steel ball with a pebble of the same weight but larger size, and of the same size but lighter weight. The following loads were used in the 12-in. laboratory mill: All 1 1/4-in. steel balls weighing 122 ± 10 g. All 1 3/4-in. pebbles weighing 123 ± 5 g. All 1 1/4-in. pebbles weighing 45 ± 3 g. To equalize capacity, the test with the steel balls was run only 34% as long as the tests with pebbles. In each case, 2,500 g of primary sands were ground at the optimum gravity for the media being tested at a speed 78 1/2 % of critical speed, and for 170, 340, and 680 revolu¬tions for the steel balls, and 500, 1,000, and 2,000 revolutions for the pebbles. The first test is summarized in Table 74 by showing the 80% passing size in microns for the feed and for each of the grinds. Two other tests are summarized in Table 75 showing the screen analyses

Jan 1, 1985

By G. Chi, M. C. Fuerstenau, R. C. Bradt, A. Ghosh

With increased emphasis on controlled blasting, which is the first and least-costly stage of comminution, ore grindability and plant throughput can be increased by 5% to 10%, and energy savings of up to 10% appear possible. Crushing and grinding efficiencies are presented for ore blasted under regular and adjusted field conditions. An economic analysis of drilling and blasting through crushing and grinding is presented, suggesting that cost savings approaching 10% may be achieved.

Jan 1, 1998

By G. L. Myers

The Fortitude skarn near Battle Mountain, NV is currently one of the largest producing gold skarns in the world. It contains about 11 Mt (12 million st) of minable ore grading 5.14 g/t (0.149 oz per st) and is the distal portion of a continuous skarn system in the Copper Canyon area centered on the Eocene Copper Canyon granodiorite porphyry. Calcsilicate compositions, opaque mineralogy, and the high gold grades are atypical of other base metal skarns (iron, Fe; copper, Cu; lead-zinc, Pb-Zn; or tungsten, W). The Copper Canyon skarn is systematically zoned from a garnet (AD 70-100) dominant, pyroxene (HD 20-45) subordinate zone, with major Cu mineralization, adjacent to the intrusive (West ore body), to a pyroxene (HD20-100) dominant, garnet (AD90-100 cores. AD 30-60 rims)subordinate assemblage, with major Au, near the distal marble front (Fortitude ore body). An extensive biotite ± diopsidic pyroxene ± kspar alteration halo surrounds the pyroxene > garnet gold-bearing skarn and represents the early stages of metasomatic alteration. Retrograde alteration is limited in areal extent and intensity, and consists of actinolite, chlorite, quartz, and prehnite. Economic gold mineralization begins in the pyroxene > garnet zone and continues to the marble front, a distance of 1 to 1.5 km (0.6 to 0.9 miles), respectively, from the plutonic contact. The opaque mineralogy in this gold zone includes pyrrhotite, arsenopyrite, marcasite, minor chalcopyrite, galena, sphalerite, argentite, hessite, hedleyite, volnyskite, and native bismuth and gold. The pyrite-pyrrhotite geothermometer yields temperatures that range from 450° C to 300°C (842° F to 582° F) and the electrum-argentite-sphalerite geothermometer yields temperatures which range from 290°C (554° F) at the marble front to about 420°C (788° F) more proximal to the intrusive. Log fS2 calculations from the sulfide assemblages yield values near - 10 with log fO2 values of about -30, in a solution of near neutral pH (5-6). Calculations of metal solubility suggest that the metals were transported as chloride complexes in the proximal skarn but that bisulfide complexes were predominant within the distal gold skarn. Relatively low oxidation states buffered by the carbonaceous to argilliceous, calcareous protolith and subsequent ferrous iron-rich skarn assemblages appear to have increased the gold carrying capacity of this large hydrothermal system.

Jan 1, 1991

By Maria S. Adusmilli, Bhaskara A. Rao, Jorge G. C. Barros, Augusto F. Mendonca

Lateritic gold has been the object of study only for a very few years, though nuggets have been mentioned in earlier works even as early as 1984 by Hartt in Brazil. In Mato Grosso State, lateritisation is intense, as is common in all tropical forest areas of the world. Exploration has revealed the presence of recoverable "nugget gold" of variable sizes (30 - 200 gms) but frequently of good size (0 - 40 gms), especially near Cuiaba and Alta Floresta regions. In both of them the host system is a lateritised breccia indicative of a fault or shear zone breccia, though in different lithological domains. The Cuiaba occurrences are phyllitic and show a profile as follows, from top to bottom: 1) Compact ferralite crust. 2) Oolitic to pisolitic compact crust (+ some gold). 3) Mottled concretionary laterite crust. 4) Lateritised "eluvial material" (gold nuggets). 5) Mottled patchy to banded laterite. 6) Banded lateritised phyllite with lenticular to banded goethite. 7) Altered red goethitic phyllite, with quartz veins (+ fine gold). 8) Unaltered grey phyllite with quartz veins (Protore). The Alta Floresta-Juruena River occurrences are volcano-sedimentary and show a profile as follows: 1) Deep brown siltitic, argillaceous and arenaceous material with organic matter (+ gold). 2) Modular and concretionary laterite, compact and indurated, with arsenophyrite in quartz fragments (gold nuggets). 3) Band with silty-clayey matrix and arenaceous in nature. 4) Bedrock meta-arcosian arenite. 5) Volcano-sedimentary with rhyodacites and andesitic basalts, with intercalations of arkosic and greywacke nature. Breccias and quartz veins, and granites associated in different portions (Protore).

Jan 1, 1988