Search Documents

By J. D. Miller

Pilot-scale tests indicate that effec¬tive concentration of fine gold from Colorado River sands can be achieved by flotation with the air-sparged hydrocyclone. The fine sands (55% minus 400 mesh and 0.01 opt*) from gravity concen¬tration were processed with a 5-cm air-sparged hydrocyclone (capacity -1.0 tph dry solids). Concentrate grades as high as 5.0 opt were produced in a single stage at a recovery of 75.0%. The separation efficiency was significantly better than that achieved in conventional batch flotation experiments.

Jan 1, 1985

By F. Dakubo

"Solvent extraction of copper pregnant solution (PLS) obtained from ammonium peroxodisulfate assisted leach was modeled using response surface methodology. Mixing speed, pH, reagent concentration and organic to aqueous (O/A) ratio were selected for testing. A pitched blade mixer was used in the experiment. Mixer speed contributed significantly to copper extraction significant, while pH had minimal effect on copper extraction. The response model developed has an R2 = 0.97 and Adeq precision of 28.3. A parallel kinetic comparing study using a straight blade Rushton turbine in a turbulent regime of mixing showed no difference (p-value =0.308) between peroxodisulfate assisted leach PLS and conventional ferric/sulfuric acid leach PLS- the power draw data support this conclusion. INTRODUCTION High arsenic chalcopyrite concentrates are a problem to the smelters all over the world due to high arsenic gas emissions during smelting. Therefore leaching is often the alternative for extracting the copper in these concentrates if dilution with low arsenic concentrate is not possible. High-pressure autoclave leaching is used. Alternatively, the use of stronger oxidants such as peroxodisulfate has been proposed [16, 18]. There is a concern brought up by the hydrometallurgy community about the faith of the organic extracting reagent coming into contact with stronger oxidant residue in the pregnant leach solution (PLS) and hence the efficiency of such extraction process. This work, therefore, looks to answer such concerns. PLS generated from leaching of chalcopyrite concentrate with the peroxodisulfate ion was used in this solvent extraction experiment. As a liquid-liquid extraction, solvent extraction involves contacting the aqueous PLS with organic extractant via mixing. Mixing is known to increase the interfacial area for mass transfer by decreasing the diffusion path length (Jussi et al.1997). EXPERIMENT Instruments and Reagents Reagent grade Acorga 5910 reagent was used in the experiment was supplied by Cytec (Current name Solvay), Ammonium peroxodisulfate and sulfuric acid were reagent grade obtained from Amazon. Apparatus The solvent extraction tests were carried in a 2000 ml plastic cylindrical reactor equipped with four 0.5” baffles. In the hypothesis test, the reactor was a 4000 ml cylindrical reactor with four 1” thick baffles arranged evening in the reactor. Comparison between peroxodisulfate and ferric leach PLS via hypothesis test"

Jan 1, 2018

By Larry S. Diaz

It is felt that prior to the presentation of the technical portion of this paper, some general information would be of interest. The Sar Cheshmeh Copper Mining Company was founded by the Iranian Government to oversee the design and construction of Iran's first copper smelter complex, which will be another step in the industrialization of Iran. Since this is the first such plant in Iran, Sar Cheshmeh wisely chose to enlist the technical assistance needed in regard to the facilities requiring engineering and operating know-how from outside of Iran. To obtain the foregoing, SCCM signed a contract with Anaconda-Iran, Inc., which was formed by The Anaconda Company for this project. The general scope of this contract covers the overseeing of engineering and design by Parsons-Jurden as well as physical plant construction. In addition to this, the same services were given to water supply and tailings disposal systems which were not included as part of the Parsons-Jurden contract. Anaconda-Iran is also assisting SCCM in setting up a training program for Iranian personnel for plant operations, administration, etc., which .will go on for some time after the plant startup, under the guidance of Anaconda-Iran expatriates. SCCM?s other responsibilities, in respect to the development of this industrial effort, are the building of a townsite for approximately 2200 families, the expected manning requirements, having all the facilities necessary to provide a pleasant life in a remote area. It has been estimated that the manpower for operations will be 2050.

Jan 1, 1976

By Michael Gay

Right in the heart of Boston Harbor lies Deer Island, where a ten-year, 6 billion dollar sewage treatment plant is under construction. The 9.5 mile long, 25.5' diameter Effluent Outfall Tunnel is the center piece of this program. A Robbins double-shielded TBM is currently driving this challenging tunnel some 400 feet below sea level. This paper will discuss the set-up and operation of this Tunnel Boring Machine in driving the longest single heading tunnel ever built in North America.

Jan 1, 1993

By S. Gopalakrisbn, J. D. Miller, M. Misra

Pilot-scale tests indicate that effective concentration of fine gold from Colorado River sands can be achieved by flotation with the air-sparged hydrocyclone. The fine sands (55% -400 mesh and 0.01 opt*) from gravity concentration were processed with a 5-cm air-sparged hydrocyclone (capacity ~1.0 t/h dry solids). Concentrate grades as high as 5.0 opt were produced in a single stage at a recovery of 75%. The separation efficiency was significantly better than that achieved in conventional batch flotation experiments.

Jan 1, 1987

By D. Tepavac, S. Simmonds

"The high virgin horizontal in situ stress field in the Sydney Basin and its impact on civil engineering projects is a well-known and accepted phenomenon found in significant literature (e.g., Pells, 2013). The prevailing high-stress effects depend on many factors — rock quality, tunnel orientation, proximity of geological features to tunnel crown, size and shape of opening, depth of excavation and stress magnitude. The behavior of the rock mass under high in situ stress conditions can cause stress fracturing and consequent dilation of the tunnel periphery, resulting in rock spalling at the tunnel crown/ invert or raveling of rock blocks on the tunnel sidewall. This type of failure is of a brittle nature and may create construction and safety risks during tunnel excavation, if it occurs behind the excavation face where ground support has already been installed. Therefore, the associated risks need to be managed during construction. This paper presents the design strategy adopted to mitigate these adverse tunneling conditions for the WestConnex Project to-date. Overview of the WestConnex M4 East and new M5 tunnel projectsWestConnex is one of the New South Wales government’s key infrastructure projects. This 33 km (20.5 mile) project aims to ease congestion and connect communities and is the largest integrated transport and urban revitalization project in Australia. It was a key recommendation of the State Infrastructure Strategy released in October 2012. It brings together a number of important road projects, which, together, form a vital link in Sydney’s Orbital Network. These road projects include a widening of the M4 east of Parramatta, a duplication of the M5 East, and new sections of motorway to provide a connection between these two key corridors. The WestConnex project includes a number of stages: Stage 1a: M4 Widening; Stage 1b: M4 East; Stage 2: New M5; and Stage 3: M4–M5 Link. The tunnel design referenced in this paper relates to Stage 1b and Stage 2 of the WestConnex Project (Fig. 1)."

Dec 1, 2018

"?irovski Vrh" Uranium deposit in Slovenia is type of mineralized sediments in ore bearing belts of deflected S-structure, in which the belt is less than 25% mineralized. Ore bodies of irregular small thickness, unreliably contoured, made difficult estimation of correct contours, which are necessary for design and exploitation works. The deposit was explored by vertical boreholes made at the surface and by boreholes fanned from drives. For the purpose of application of this estimation method, 1 m composites have been made in slices which were parallel to the referential belt plane. Estimation was made for 1,5m x 1,5m x lm blocks which do correspond to the size of the containers in the ore transport stage. Two variables have been used: the first, indicator of function (ore=1, waste material =0) and kriging method; the second, logarithmical content of Uranium and Minimum Mean Square Error Estimation (MMSEE) method. Based on estimated values of those variables, probability of ore quantity as well as Uranium content over determined cut-off were calculated for each block. Those two parameters enable determination of the most probable form of the ore body in ecah one metter slice. Estimation of sixteen small blocks in a large 1,5m x 1,5m x 1m block made possible estimation of ore quantity and its content for the determined cut-off, as well as categorization of exploration. This method is being used for estimation of ore reserves and planning of exploration operations. The described' methodology was tested in an exploitation block.

Jan 1, 1986

Lingering effects of the 1990 oil shock that included overbuilding and corporate and individual financial distress caused the Gross Domestic Product to fall slightly to $5.67 billion (US billion = l09). With 254 million people - 697,000 in mining and petroleum - the US has more than 100 million dwelling units and 190 million licensed motor vehicles. New private housing starts fell 15% to one million units. New car production fell 11 % to 5.4 million units. Truck and bus production fell 8% to 3.4 million units. The inflation rate was 3%, while the prime rate of interest was 8.5%. The Producer Price Index (1982 = 100) changed as follows: -fuels and related products and power down 1% to 8l, • metals and metal products down 2% to 120, • chemicals and allied products up 2% to 126, and • non-metallic mineral products up to 2% to 117. Energy Imports of crude and refined petroleum, costing $50 billion, fell 5% to 2.8 billion bbl. Domestic petroleum production rose 1% to 3.6 billion bbl. Petroleum supplied about 39% of US energy, natural gas 24% and coal 22%. The National Energy Strategy was announced in February 1991. Its purpose is to encourage domestic production of fossil fuels and nuclear and renewable energy and to stimulate efficiencies in use. Congress continued to debate the strategy and took no action. Coal production fell 3% to 902 Mt (994 million st). About 60% of that came from surface operations. Seventy-eight percent of the total was used to generate electricity and 3% was coked.

Jan 1, 1992

By G. Norman Owen, Roger E. Scholl, Tor L. Brekke

INTRODUCTION Underground structures are generally regarded to be safer than surface structures during strong seismic motion, except when crossing a causative fault. Recent studies of observed earthquake damage to tunnels generally support this view, although instances of severe damage and, occasionally, collapse are reported. For proposed underground construction of sensitive structures such as nuclear power plants, liquefied natural gas facilities, and nuclear waste repositories, a verification of the seismic response of underground structures will be required.. This paper discusses the stabilization recommendations used in a study of additional costs required to protect tunnels against ground motion caused by earthquakes and underground nuclear explosions (1). The study is a part of the site investigations for possible construction of a nuclear waste repository. The additional costs estimated in the study are not presented here; only the stabilization measures are presented in the present paper. The tunnels, which would constitute the underground facilities of a possible repository, are assumed to be 5.5 m (18 ft) in diameter and to be located at a depth of 600 m (2,000 ft). Three candidate geological materials are considered: argillite (shale), granite, and tuff. Several peak ground accelerations are used: 0.3g, 0.5g, and 0.7g for earthquakes, and 0.5g, 0.7g, and 1.0g for underground nuclear explosions. Potential damage due only to shaking is considered here. This paper does not discuss problems that result from creep or sudden rupture of intersected faults or from ground failures at portals.

Jan 1, 1979

By J. C. Squire, E. W. Baker, G. A. Sullivan, G. W. Flathers

A mine collapse severs communication with trapped miners. Landlines are crushed and commercially available radios cannot penetrate hundreds of feet of dense, conductive earth without the use of regenerative repeaters that may also be crushed. This paper describes a proof-of-concept device that uses seismic P-waves, instead of radio waves, to allow communication of a code that represents prearranged messages, including the safe haven location identifier, number of people and air quality, from trapped miners to aboveground rescue units. The transmitter designed is about 0.03 m3 (1 ft3) in size and can broadcast for four hours from its 27-kg (60-lb) battery pack. The receiver consists of a geophone and a 2.5-kg (5.5- lb) signal conditioning unit attached to a laptop computer, which displays the communication signal in real time. Testing in a bituminous coal mine with an MSHA representative revealed the device was able to transmit through 271 m (890 ft) of overburden, at 0° and 12° from vertical, using 500 W of power.

Jan 1, 2009

By Monica Pavlik, Thomas Wildeman

Water from the Forest Queen mine adit near Silverton, Colorado drains into a natural wetland. Because the pH of the water averages 5 and the iron concentration averages 18 mg/L, it was thought that the wetland might naturally treat the water. Of most concern with respect to the aquatic environment is zinc whose concentration averages 0.60 mg/L. Starting in October 1997, the surface waters, ground waters in the peat substrate, and the sediments in the wetland were sampled and analyzed four times over the course of four months. The adit water primarily remains as surface water where Fe, minor amounts of Al, and no Zn are removed. After the adit water enters the peat, then it is found that the pH rises to 5.8-6.5 and sulfate is reduced. The removal of Zn and A1 is caused by these two changes. However, Fe in its reduced state is quite soluble and may be remobilized in the reduced environment of the peat.

Jan 1, 2000

By D. S. Bird

Kennecott Utah Copper began a modernization program in 1986 that was aimed at expanding and updating mining and ore process facilities at the company’s Bingham Canyon copper mine and concentrator near Salt Lake City, UT. Major components of the project included installation of an in-pit crusher, a transfer conveying system and a new ore concentrator with a design capacity of 70 kt/d (77,000 stpd). The Copperton concentrator was commissioned in February 1988. The grinding circuit is one of its principal features. It consists of three identical lines, each with a 10.4-m- (34-ft-) diam x 4.6-m- (15-ft-) long semiautogenous grinding (SAG) mill and two 5.5-m- (18-ft-) diam x 8.6- (28-ft-) long ball mills. The SAG mills are driven by two 4.5-MW (each) (6000-hp) variable- speed dc motors through a clutch-pinion gear-ring gear assembly. The ball mills are driven by 4.1-MW (5500-hp) synchronous motors coupled through a typical clutch-pinion gear-ring gear system.

Jan 1, 1995

By Sigmund J. Sulinski

All Sanitary District contract documents for new tunnel construction permit the Contractor a choice of four (4) separate alternate tunnel sections. This is the result of a continuing District policy to encourage at all times the use of the most suitable construction techniques and to attract to District construction the broadest spectrum of proven capabilities. Figure 1 indicates the alternate tunnel sections allowed on District contracts as follows: 1. A horse shoe section, ribbed and lagged, and a poured reinforced concrete tunnel liner; 2. Circular section, ribbed and lagged, and a poured in place reinforced concrete tunnel liner; 3. Circular section, ribbed and lagged, and a precast reinforced concrete pipe liner grouted in place; and 4. Circular section, no temporary lining, and a precast reinforced concrete pipe liner to be jacked in place. The Sanitary District now has in operation 10,500' of 5'6" I.D. and 6,500' of 5'0" I.D. jacked tunnel. An additional 5,600' of 7'6" I.D. jacked tunnel is currently under construction.

Jan 1, 1997

By P. W. Hunter

The construction of a major sewerage scheme requiring 15.3 km of 5.5m excavated diameter tunnel in basalt, mixed and soft ground has been undertaken by the Melbourne and Metropolitan Board of Works. A double shielded Tunnel Boring Machine was selected to excavate 13.7 km of basalt and mixed ground. Advanced methods for recording operational data on the TBM were introduced. Progress to date has shown that the TBM can excavate rock very effectively with a best weekly production of 178.8m; soft ground has been encountered and successfully handled.

Jan 1, 1987

By Jr. Gambrell

Support characteristics of in-cycle trusses are analyzed using a photo-elastic model loaded by tightening a truss in the sequence normally used in an underground mine. Stresses in the roof at its center point and at the junction of the roof and rib are examined. Effects of zero tension and unequal tension in the inclined anchor rods are presented. Effects of simulated subsidence on stress in the roof surface and on tension in the separate truss members are examined. Conclusions are drawn relating to (1) the effects of tension in the inclined anchor rods on uplift and compressive stress parallel to the roof surface, (2) the effects of subsidence on stress in the roof surface and, (3) the effects of subsidence on tension in the truss members.

Jan 1, 1989

By C. E. Schmidt

Homestake crushing and grinding, practice-was completely revised during the period of 1951-1953. During the conversion, both crushing plants at the head frames the Ross and the Yates, were changes at each plant involved replacing the two 8K gyratories with a rebuilt, The flow sheet single thirty inch gyratory for primary crushing to four inch. The gyratory discharges to a seven foot Symons standard cone crusher set at 1-1/8 inch opening. The cone discharge goes to Tyrock screens fed by vibrating feeders. Screen openings, are l/2 inch by 5 inches: at the Ross. Plant, and 3/8 inch by 5; inches at the Yates. Screen oversize goes to a seven foot Symons cone brusher converted to the short head type; the crusher setting is 5/16 inch. Crusher, discharge; is closed circuited with the Tyrock screens, The above crushing installation delivers a minus 5/8 inch rod mill feed to the mill bins. The crushing revision eliminated the-180 heavy South African type stamps, which had previously reduced the 2 inch crushing plant product to a minus 5/8 inch feed for the 10 rod mills, and 8 ball and pebble.; mills, other revisions in the mill flow sheet, resulted in 3 identical units of about 1350 tons per day, capacity per unit, Each unit consists of an open, circuit 6 foot by 12 foot rod mill, fed from two 24 in by 48 inch vibrating feeders of the four feeders available per unit. A gathering belt delivers the ore discharge of the feeders to the Transportoweigher, which in turn discharge s, into the rod; mill feed spout. Rod Mill discharge is the feed for the 9 foot by 11 foot ball mill, The ball mill is closed circuited with a 16 foot by 30 foot Dorr Classifier. The Homestake make amalgamator, for coarse gold recovery in the ball mill circuit, made' necessary a 36 inch spiral conveyor between the classifier rake discharge and, the combination drum and double scoop feeder on the ball mill See Figure l - the flow sheet of the two stage grinding units.

Jan 1, 1958

By W. Holding

Since the 1975 International Mine Ventilation Congress in Johannesburg there has been a trend in South Africa towards making the mine ventilation departments responsible for monitoring the total environment. This includes the taking of noise and illumination measurements and there is in fact a debate taking place as to whether the departmental title should be changed to 'Environmental Control Department'. The organisers of the 2nd international Mine Ventilation Congress have decided that noise and illumination will not be included as Congress subjects and 'Total Environment' includes only those facets which are open to debate at the Congress. The choice of mine is significant in that while most Congress papers from South Africa will be devoted either to coal mining or to the somewhat unique deep level gold mines, Prieska Copper Mine is a mine which can easily be identified with similar mines in many other parts of the world. The mine is situated some 750 km south west of Johannesburg and about 600 km north east of Cape Town. Current production (ore and waste) is about 340 000 tons per month and the total underground labour force is just over 2 000. The ore body is a massive sulphide, the main minerals being copper and zinc and the method of mining is sub-level open stoping. Daily average surface temperature conditions range from 85°F (29.5°C) dry bulb and 69.8°F (21°C) wet bulb in mid-summer to 42°F (5.5°C) dry bulb and 36.5°F (2.5°C) wet bulb in mid winter. The information presented in-this paper is limited to what can be gathered by mine ventilation staff as part of an on-going exercise and is obviously not as comprehensive as would be the case if a fully equipped research establishment were to become involved. The paper will be divided into three sections 1) Gases 2) Dust 3) Heat In each section statutory and/or other standards will be set down followed by a discussion of assessment and in some cases control methods.

Jan 1, 1980

By Ernest A. Draeger, James W. Collins

Water only cyclones, sometimes referred to as hydrocyclones, are one of the newest types of coal processing equipment. These devices have achieved wide acceptance as fine coal cleaners in the past decade. Many metallurgical coal plants employ water only cyclones to process 0.5 mm x 0 size coal. Some of these plants have as many as 40 to 50 305-mm-diam units with each unit receiving as much as 9 t/h of raw feed. The growth in the utilization of hydrocyclones is due partly to the energy shortage, partly to the general increase in over-all coal preparation, and also because of a need for a simplified fine coal (0.5 mm x 0 size) gravimetric separator. Large diameter water only cyclones are also available and in use to process feed sizes up to 32 mm in size. However, the size normally employed for cleaning 0.5 mm x 0 coal are 356 mm or 305-mm-diam for single-stage circuits. In two-stage circuits, the secondary units are normally the same diameter as the primary units or smaller, such as 203-mm-diam. By using the small diameter cyclones and treating a closely sized feed, 0.5 mm x 0 only, it has been found that the probable error or imperfection of the water only cyclones is comparable to that obtained on the same size fraction treated in a large 610-mm-diam heavy media cyclone washing 38 mm x 0. The water only cyclone can approach the efficiency of a heavy media cyclone when cleaning fine solids because it creates its own dense media by accumulating high specific gravity particles in the wide angle conical section of the cyclone. A cut-away cross sectional view of a water only cyclone is shown in Fig. 1. It is also true that when treating a wide range of sizes (38 mm x 0) in heavy media cyclones, the smaller size particles (0.5 mm x 0) separate in proportion to the split of the media through the cyclone rather than by particle density.

Jan 8, 1980

By Diler Katircioglu-Bayel

This study aims to investigate the effect of combined mechanical and ultrasonic milling on the size reduction of talc. First, the talc sample was wet-ground in a stirred media mill for five different lengths of time (30, 60, 90, 120 and 150 min), and the optimum result was subsequently achieved with treatment by ultrasonication. The effects of amplitude (20, 35 and 50 µm), solid ratio (2.5, 5, 7.5 and 10 percent), and sonication time (60, 120 and 240 min) on the sizes of the final product were investigated. The pre-milling by wet grinding caused a decrease in the grinding resistance of talc. Sequential ultrasonic treatment, which was applied to the talc sample, generated smaller particles in comparison to those acquired by stirred media milling alone. Experimental results were assessed based on the product particle size (d10, d50 ), reduction ratio and specific energy consumption. Submicron particles prepared by ultrasonic treatment were highly stable compared to stirred media milling alone as investigated in terms of particle size. In addition, the effects of mechanical and ultrasonic milling on the structural properties of talc particles were characterized by X-ray diffraction (XRD) analysis.

By K. Morsy, S. S. Peng

A new method of pillar stability evaluation was proposed. The unique feature about the method is that it estimates two types of stability factors for the pillar. The first stability factor is to measure how much the applied stress at that point is smaller than its strength, and the second stability factor is to predict whether or not the pillar will fail violently. The strain-softening behavior of coal pillars was simulated by the Drucker-Prager yield criterion. A new algorithm that simulates the strain-hardening behavior of the gob was used. A numerical technique to estimate the local mine stiffness (LMS) was introduced and verified by both numerical and analytical methods. A case of massive pillar failure in a room-and-pillar mine was used to define the stability limits for the proposed method.

Jan 1, 2003