Search Documents

By N. S. Dalal, V. Castranova, K. Van Dyke, V. Vallyathan, J. H. Kang

Previously we reported crushing or grinding crystalline silica results in silica-based free radicals on the particulate surface which can generate hydroxyl radicals in aqueous solution (1). Now we find that freshly ground silica is more cytotoxic to and a more potent activator of alveolar macrophages than similarly sized aged silica. Since the United States Department of Labor estimates that over 1.25 million American workers may be exposed to freshly ground crystalline silica arid nearly 60,000 may be at risk of developing some degree of silica-based occupational lung disease, then this is hardly a trivial problem. Occupations of concern include workers who come in contact with silica including miners of soft and hard minerals, stone quarry workers, glass workers and even millers who stone grind flour. Acute silicosis is manifested by inflammation, alveolar lipo-proteinosis, and the rapid development of respiratory disability that depending on the dose of silica can produce chronic silicosis which takes 20 - 40 years to develop. It is demonstrated by the appearance of concentric hyalinized nodular lesions and progressive development of dyspnea(3). Certainly the free radicals produced on the surface of freshly ground crystalline silica play a most important role in producing the acute and chronic symptoms of silicosis. When respirable-size freshly- ground silica (0.1 -- 5 microns in diameter) enters the deep alveolar spaces in the lung and contacts an aqueous environment, hydroxyl radical are generated and cellular damage is bound to occur. We have found that freshly ground silica can cause lipid peroxidation and lysis of erythrocytes(1). The objective of this investigation was to further elucidate the enhanced toxicity of freshly ground versus aged silica. It can be deduced from the data that not only is freshly ground silica more cytotoxic to alveolar macrophages but it is a more potent stimulant of these phagocytes. However the mere characterization of toxicity is not entirely helpful if there is not a useful means to detoxify the cause of the damage. We have identified an aqueously soluble substance that can be used in high dilution to detoxify the SiO(•) and Si(•) type of free radicals. This is the organosilane known as Prosil 28 (R). We have found that coating of the freshly ground silica can effectively reduce its toxicity. The importance of this observation is that such a coating could be used with water cooled drills. This may partially detoxify silica at the point of generation of the free radical, i.e., the generation of the fresh silica dust itself. Such a coating could be used in great dilution 1:103 or 1:104. The coating would be long lasting, inexpensive and should be non-toxic because of the great dilution.

Jan 1, 1991

By D. T. Iseley, David Bennett, Christopher Norris

The microtunneling test program is one of three main elements of the research project, "Trenchless Construction: Evaluation of Methods and Materials to Install and Rehabilitate Underground Utilities." The other elements of this project include an evaluation and demonstration of horizontal directional drilling technology and pipeline rehabilitation systems. The research is a Corps and Industry cost-shared project funded under the Construction Productivity Advancement Research (CPAR) program. The laboratory partner is the U.S. Army Engineer Waterways Experiment Station (WES), Geotechnical Laboratory. The industry partner is the Louisiana Tech University's Trenchless Technology Center. Industry participants are contributing over half the total cost of this research. The overall objective of the CPAR program is to improve productivity in the U.S. construction industry, thereby enhancing the competitiveness of the U.S. industry in domestic and overseas markets. The Corps and other federal and state agencies will benefit by realizing reduced costs, enhanced safety and better products and services as the products of this research program are developed, tested, and pushed into the market place. The microtunneling demonstrations and evaluations were performed during September and October 1992 at a specially constructed test facility built at WES in Vicksburg, MS. The test facility is 104 m (340-ft) long, 5 m (16-ft) wide, and 4 m (13-ft) deep. It was constructed, ironically, by first excavating a trench into which 6 different types of soils were placed and compacted in approximately 18.3 m (60-ft) long sections. The soil profiles include a lean silty clay (loess), a dry sand, highly plastic buckshot clay, wet sand, clay gravel and silt. The interfaces between soil profiles were sloped to simulate mixed face conditions as the machines exit one zone and enter another, and provided challenges to ground control and alignment and grade control during these transitions. Moisture and density tests were performed on all materials in each lift to assure uniformity. Horizontal inclinometers and 3 levels of settlement plates were installed at key locations in the test bed. The settlement plates and rods and the horizontal inclinometers, together with surface survey points, provided data to evaluate settlement and heave along the test section. Penetration resistance was measured in each section of the completed test bed. Strain gages were installed in 8 of the 0.6 m (24 in.) diam. Hobas pipe sections to measure strains in the pipe as it was being jacked into place. Steering jack loads, jacking thrust loads, and cutterhead torque were also measured during the drives. The results of these tests will be used together with other information to develop guidelines for conducting feasibility studies and selecting proper methods compatible with anticipated conditions.

Jan 1, 1993

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION This method is a variation of cut-and-fill mining where either the wall rock or the vein is too unconsolidated to permit safe mining by conventional cut-and-fill methods. Basic development consists of driving a 2.4 x 2.7-m (8 x 9-ft) haulage heading laterally in the footwall side of the vein. Crosscuts are driven over to the vein at 91-m (300-ft) intervals. Then the vein, at each inter¬section, is mined out to a distance of about 9 m (30 ft ) above the track level. After the installation of an ore chute, scrams or intermediate drifts are driven in both directions along the vein. Mining then starts imme¬diately below the level bounding the upper limit of the stope. A cut varying between 3 and 4.2 m (10 and 14 ft) in depth and mined for a distance of 45.7 m (150 ft )along the strike is taken from the orepass in each direction (Fig. 1). In this mined-out void, the floor of the cut is equipped with 203 x 203-mm (8 x 8-in.) caps hitched into the wall with steel saddle hitches installed on 1.5-m (5-ft) centers. Double wood stringers, 152.4 x 152.4 mm (6 x 6 in.), are then installed on 1.2-m (4-ft) centers longitudinally down the length of the stope. Reinforc¬ing wire mesh is also placed, overlying each mat of timber. Directly above the stringers, stulls are installed from hanging wall to footwall to hold the timber in place during the sand-filling operation. Then a cement¬sand mixture in a ratio of about 1:10 weight is poured to a depth of about 2.4 m (8 ft). The entire cycle is then repeated down to the scram drift. Another variation of timbering is illustrated in Fig. 2. There is a vein width of approximately 5.5 m (18 ft) with the same unconsolidated ground conditions. The primary difference between handling this situation and the previously described undercut-and-fill method is that standard timbered sets are installed in each excavated stoping void rather than stulls. Once again the basic method is to work down the ore block from an upper timbered drift to a lower timbered drift. Cuts are taken from a timbered raise with a chute on the stope side. Each piece of ground excavated is essentially two sets high, 5.5 m (18 ft), by two sets wide, 5.5 m (18 ft), by the length of the cut along the strike of the vein. The timbered sets are 2.4 x 2.4 x 2.4 m (8 x 8 x 8 ft). The net result is, therefore, two sets of timber on a top floor separated by doubled-up 76-mm (3-in.) lagging from

Jan 1, 1982

By G. E. Jones, G. K. Hoffman

Two Sun Juan Basin studies were completed through the USGS National Coal Availability program. The study areas are in the northwest Bisti field (Fruitland Formation) and in the eastern Standing Rock field (Menefee Formation). In the Bisti and Standing Rock areas, the original coal resource5 are estimated at 4.66 and 3.1 7 Gt (5.14 and 3.49 billion st), respectively. The Bisti coal resources are greatly reduced by the Bisti-De-Nu- Zin wilderness area, which contains an estimated 1.13 Gt (1.25 billion st) of coal. Technological restrictions remove 32.5% from Standing Rock's original resource. Available resources are 60%. 2.79 Gt (3.07 billion st), of the Bisti original resource and 65%, 2.07 Gt (2.28 billion st), of the original Standing Rock resource.

Jan 1, 2002

By A. S. Malicsi, Vathsala Rajagopal, I. Iwasaki

Corrosion and abrasion properties of a series of chromium-containing, cast-iron balls, with Cr contents ranging from 0% to 29%, were evaluated and compared with austenitic stainless-steel and mild-steel balls. Marked ball wear tests were performed on artificial ore samples consisting of 95% quartzite, with either 5% pyrrhotite or 5% chalcopyrite, under a nitrogen or oxygen atmosphere. The electrochemical mechanism was investigated by correlating the corrosive wear with the corrosion currents obtained from potentiodynantic polarization curves under abrasion. Flotation recoveries were determined on a 95% quartzite + 5% pyrrhotite sample ground with various cast-iron ball materials under an oxygen or nitrogen atmosphere. Electrochemical results are found to be in good agreement with flotation results and with corrosive wear data obtained from marked ball wear tests.

Jan 1, 1993

By Richard E. Ray

INTRODUCTION Main mine fan installations at underground coal mines must be designed to comply with the requirements outlined in 30 CFR (Code of Federal Regulations) Part 75. However, very little emphasis is typically placed on the aerodynamic optimization of shaft collar designs, ductwork configurations, and the selection of a fan isolation, or "closing door," system. Field testing has shown that poorly designed systems may produce large pressure losses between the shaft and fan inlet, as well as air turbulence problems which adversely impact fan efficiency and sometimes fan structural integrity. This paper analyzes each component of a surface exhaust fan system for an underground coal mine: • The shaft collar arrangement, • The 45 or 90-degree turning duct that isolates the fan motor from the return airstream, • Alternative ductwork arrangements for parallel fan installations, • The self-closing doors or dampers that are required for multiple fans, and • Horizontal and vertical evas6 arrangements on the discharge side of the fan. While discussion is limited to axial fan installations at shaft mines, most of the recommendations would also apply to centrifugal fan installations and to main mine fans for drift mines. FEDERAL REGULATIONS The mandatory safety standards for underground coal mines that apply to the installation of main mine fans are listed in 30 CFR Part 75.310. Stipulations which impact the design of the fan sys- tem arrangement are contained in paragraphs (a)(l), (a)(5), (a)(6),(d), and (1) of 75.31 0: • Each main mine fan shall be installed on the surface in an incombustible housing; • Each main mine fan shall be protected by weak walls or explosion doors in direct line with possible explosive forces; • Explosion doors or weak walls shall have a cross-sectional area at least equal to the area of the return air shaft or drift opening through which the pressure from an underground explosion would be relieved; • Each main mine fan shall be offset by at least 4.57 m (15 feet) from the nearest side of the mine or shaft opening; • Automatic closing doors shall be provided to prevent possible air reversals through the fans in mines ventilated by multiple main mine fans. The installation of main mine fans underground is prohibited by 30 CFR Part 75.310, (a)(l). Providing explosion doors or weak walls in line with a possible underground explosion and offsetting the fan 4.57 m (1 5 feet) from the edge of the shaft preclude the installation of the fan directly over the shaft. In addition, 30 CFR Part 75.507-1 specifies that all electrical equipment used in return air courses be permissible, which requires locating the fan motor outside of the airstream exhausted through the fan. To comply with the Part 75.310 regulations, explosion doors are typically located directly over the shaft as part of the shaft cover or 'bonnet." A sufficiently long section of ductwork placed between the shaft enclosure and fan, equipped with a 45 or 90- degree turn, enables the fan to be offset at least 4.57 m (1 5 feet) from the shaft and the motor to be isolated from the airstream. The need for the turn in the ductwork can be eliminated by driving the fan from the discharge side, instead of from the inlet side, and providing for a 90-degree bend in the evas6. For multiple main mine fan systems, self-closing doors can be located on the inlet or discharge side of the fan. FAN SYSTEM COMPONENTS A poorly designed exhaust fan arrangement will produce turbulent conditions at the fan inlet and significant pressure losses between the shaft and fan. Field tests have shown that pressure losses through inlet ductwork at some installations may constitute as much as 30 percent of the total mine head. Unfavorable flow conditions may cause a change in the operating point on the fan performance curve, resulting in reduced fan efficiency and pres- sure generation capability. In some instances, poor airflow distribution through the fan may create mechanical stresses that lead to fan blade or fan housing fatigue failures. The objective in designing an air duct arrangement for a fan system is to provide a low cost duct that will move the air from the shaft to the fan in a uniform air distribution and with minimum energy requirements. The optimum solution is a compromise between technical and economic factors. Aerodynamic design considerations for the shaft collar and cover, fan inlet ductwork for both single and parallel fans, self-closing doors, and evas6 are discussed in the sections below. Shaft Collar/Cover To prevent excessive turbulence and non-uniform air distribution through the fan, a smooth transition for the change in direction of airflow at the top of the shaft must be provided. However, the concrete lining of the shaft is abruptly terminated at the surface at many coal mine installations (see Figure I), creating a sharp 90-degree bend. The airflow exiting the shaft becomes heavily concentrated in the upper portion of the horizontal fan in-

Jan 1, 1997

By Reed S. C. Rogers

The breakage parameters of phosphate ore were determined by batch first-order grinding studies in a laboratory ball mill according to the procedures described in the text by Austin, Klimpel and Luckie, using a slurry density of 70 weight percent. The results were scaled to five larger mills of 0.56 m diameter by 0.91 m length (2 ft. by 3 ft.), 0.82 m by 1.52 m (3 ft. by 5 ft.), 3.36 m by 7.90 m (11.5 ft. by 25 ft.), 4.41 m by 9.10 m (14.5 ft. by 30 ft.), and 5 m by 11.1 m (17 ft. by 36 ft.), assuming equilibrium ball charges for the full-scale mills. The results were used to predict product size distribustions and capacities for batch grinding in the 0.56 m and 0.82 m diameter mills and open circuit grinding in the 0.82 m diameter and larger mills using a one-large/two-small reactors in series model fitted to the residence time distribution measured in the 4.41 m diameter mill. The simulated results were compared to plant data for ranges of mill capacities. It was found that the simulated product size distributions were in good agreement with the experimental values below the 70% passing sizes, but did not agree so well in the top sizes. The predicted capacities were in approximate agreement with experimental values for the pilot-scale mills, were about 7 percent too high for the 3.36 m and 4.41 m diameter mills and about 25 percent high for the 5 m diameter mill. Use of the Bond method with the measured Work Index of the phosphate ore gave capacity predictions that were 45 to 150 percent too high.

Jan 1, 1985

By E. F. Klein, R. L. Eacret

Introduction In contrast to the general type of crushing mechanism in which the crushing surfaces alternately approach and withdraw from each other, described earlier in this section, and continuous-pressure break¬ers such as rolls and roller mills that will be described in a later chapter, impact crushers load by striking pieces of rock while in free fall and hurling them at high speed against stationary surfaces. Because the impact crusher depends for its effectiveness upon high velocity, wear is greater than in the slower-moving jaw and cone¬type wear parts, and for this reason its use is strictly limited to rela¬tively soft, friable, and sticky rocks that are characteristic of many nonmetallic mineral deposits. A few of these are phosphates, lime¬stone, barite, clay, asbestos rock, and coal. However, several examples of their use on soft lead-zinc and precious metal ores have been known. Although the use of impact crushers is expanding today into the range of ores containing as much as 15-18% silica, Taggart16 set the practical limit at 5%, and in the 1940s and 1950s several installa¬tions in the US and western Europe exceeded the limits of economical maintenance and were quickly superseded by the slower-moving, con¬ventional crushers. A rock that tends to be plastic or bouncy in a jaw or gyratory crusher when the force is applied slowly to reach ultimate strength, may become brittle with rapid loading and thus increase the effective¬ness of the applied forces. For this reason it is to be expected that as the quality of hammers, grates, plates, and cages improves with advances in steel technology, the use of high-speed crushers of this kind will increase. Terminology Modern usage differentiates between the impactor and the hammer mill, the former relying primarily on the impact of hammers (fixed or free-swinging) and secondarily upon pieces striking one another or steel surfaces; the hammer mill relies on both the centrifugal impact force of free-swinging hammers and the attrition and shear action between these hammers and well-placed grates suspended at the bot¬tom just below the hammer circle. The hammer mill, because of its grate discharge, restricts discharge of oversize rock to the grate open¬ing, while at the same time providing a trap for removal of tramp iron or other uncrushables. The impactor discharges free, so generally works with a screen to control product sizes. The question of terminology, impactor vs, hammer mill, creates difficulties because the similarities appear to outweigh the differences by far; if one were to list the similarities in order of importance and then the differences, he would be forced to conclude that they would best be dealt with as a single kind of crusher. Taggart16 gave it four names and added "as it is variously known," but it must be remembered that in 1945 the machine was nearly exclusively of the flailing-hammer type, while today the fixed-hammer rotor is also com¬mon. In this chapter the terms impactor and hammer mill will be used where they seem to apply. It is perhaps unfortunate that this terminology is being confused with rock breaking at the mine, usually with hand-held tools, e.g., the article "High-Energy Impact Rockbreaking" by Grantmyre and Hawkes, CIM Bulletin, August 1975. General Description Impact breakers, impact crushers, and hammer mills accomplish material breaking and reduction primarily through impact action of the material with fixed or free-swinging hammers revolving about a central rotor. The material to be crushed enters through an opening at the top or top side known as the "feed opening" or "hopper opening" and falls into the path of rotation (hammer circle) of the hammers. Initial breakage is accomplished in midair by collision of the dropping feed material with high-speed hammers. The second stage of breakage occurs when the pieces hit plates or breaker bars which line the crusher boxlike frame. Hammer mills rely further on a shearing and attrition action between free-swinging hammers and grid bars or grates at the crusher bottom which restrict discharge of oversize material until it is broken sufficiently to pass through the grid opening. The term hammer is used in reference to the piece which strikes the material, whether it is fixed on the rotor or free-swinging. It

Jan 1, 1985

By R. E. Le Messurier

GENERAL DESCRIPTION The mines are located at Broken Hill in the western part of New South Wales, Australia, 930 km west¬northwest of Sydney. Mining Methods Where pillars must be left between stopes, extraction of a block of ore between two or more levels is carried out in stages: 1) Stopes are mined overhand by horizontal cut¬and-fill stoping, or by long-hole stoping. The various methods of horizontal cut-and-fill stoping used are desig¬nated as: -Loader cut-and-fill stoping with horizontal blast¬holes and diesel load-haul-dump (LHD) units. -Open stoping with horizontal blastholes and com¬pressed air or electric scrapers, or with diesel or electric LHD units. Square-set timber stoping, where ground condition precludes open stoping. The backs are sup¬ported with timber square sets. Pattern rockbolting of the backs may be used as an intermediate stage between open stoping and square-set stoping. 2) Vertical pillars are mined by undercut-and-fill stoping or by vertical crater retreat stoping. 3) Where a horizontal pillar has been formed below the level above the primary stope, this level pillar, usually 6.1 to 8.2 m in depth, may be mined by over¬hand square-set stoping or by undercut-and-fill. Long-hole stoping is used at the Zinc Corp. (ZC) and New Broken Hill Consolidated (NBHC) to mine parts of the zinc-rich A and B lodes. Drilling is carried out from drill drives and, in some cases, sills. Hole sizes used are 165 mm (61/2 in.), 110 mm (4'h in.), and 65 mm (21/2 in.) nominal diam with hole lengths being limited to 50, 30, and 20 m respectively. Ammonium nitrate-fuel oil (ANFO) and water gel explosives are used. Broken ore is loaded from drawpoints at the bottom of the stope using rubber-tired diesel-driven LHD units which deliver ore to an orepass. Annual production at Zinc Corp. and NBHC accord¬ing to mining method is given in Table 1. At Zinc Corp. mining is being carried out at depths varying between 200 and 832 m. At NBHC it ranges from 528 to 915 m below the surface. The average travel time to the stope is 30 to 45 min. GENERAL ORE BODY REQUIREMENTS Size, Shape, and Dip There are six separate lodes which carry minable ore in the mines of Zinc Corp. and New Broken Hill Consolidated. The lowest of these and the main ore bodies presently being mined at Zinc Corp. are the lead lodes, consisting of a siliceous fluoritic ore body (No. 3 lens) and overlying it a calcite rhodonitic ore body (No. 2 lens). Each possesses characteristic ratios of lead, silver, and zinc, although the grade within each lens is variable, in places being as high as 30% Pb. There are also low¬grade portions which consist chiefly of poorly mineral¬ized rhodonitic material. No. 3 lens terminates within the Zinc Corp. leases, while No. 2 lens continues into the NBHC leases where it continues to provide a significant proportion of pro¬duction from the mine. Overlying the No. 2 lens are the various zinc-rich ore bodies. In ascending sequence these are lower No. 1 lens, upper No. 1 lens, A lode, and B lode. A typical assay for the small No. 1 lens group ore bodies is 8% lead, 50 g/t silver, and 20% zinc. The `A' lode is a large low-grade ore body in which the higher grade sections assay 4% lead, 30 g/t silver, and 10% zinc; larger quantities of lower grade ma¬terial also occur. B lode, the main zinc lode, typically assays 5% lead, 30 g/t silver, and 17% zinc. B lode increases in size as it extends south, and in NBHC is a major ore body, contributing about 52% of the production. All the lodes pitch south, the average pitch being 0.52 rad (30°) in the Zinc Corp. leases and rather flatter than this in the NBHC leases (see Figs. 1-3). The ground is all competent rock. Production requirements at Zinc Corp. are 900 000 t and 1 200 000 at NBHC.

Jan 1, 1982

By W. C. Dailey

The National Steel Pellet Company is owned by National Steel Corporation, managed by the M. A. Hanna Company and located near the town of Keewatin in northern Minnesota. Annually, the concentrator processes 15.24-Mt (15.0 million It) crude taconite with eight 8.2-m diameter by 5.5-m long (27 ft x 18 ft) wet semi-autogenous (SAG) mills to produce 4.57-Mt (4.50 million It) of iron ore pellets. To improve operating costs and primary mill grinding circuit efficiencies, a task force on liners was formed with the operation, maintenance and engineering staff at N.S.P.C. along with the local supplier of mill liners. Results of the task force recommendations since 1980 along with improvements made in the primary circuit operations, are presented. Mill Liner Design and Metallurgy Changes The primary mill liner task force was formed in 1977. Its function was to improve the operating costs and milling efficiencies of the ten 8.2-m x 5.5-m (27 ft x 18 ft) wet SAG mills that were operating at the time. The SAG mills are driven by two 3500 HP motors drawing a total of 5450 kW at 76% of critical speed.

Jan 1, 1985

By Charles C. Y. Chen, Duane R. Skidmore

Batch leaching of Ohio #1, Ohio #4A and Ohio #5 coals was conducted with the thermophilic. sulfur, oxidizing microorganism: Sulfolobus acidocaldarius. Four different size fractions of each coal, with median sizes of 508, 200, 90, and 49 microns, were subjected for 10 days to leaching in a 5% coal-water slurry at 72°C and a pH of 2. Release rates and extent of sulfate and iron I1 and I11 ions from the coals during the leaching process and distribution of sulfur forms (sulfate, pyritic and organic) in the coal samples before and after treatment were determined. Data indicated that Ohio #1 coal, with an initial sulfur content of 0.6%, showed no significant changes with leaching in total sulfur content or forms of sulfur. The Ohio #4A coal, with initial total sulfur content near 5%, yielded product, for sizes below 200 microns with 90% reduction of pyritic sulfur while the extent of organic sulfur removal varied with coal particle size. Results similar to those for Ohio #4A were observed on the Ohio #5 coal, which had an initial total sulfur content of 3% and a final sulfur content near 1%. The findings were interpreted in terms of basic biological, chemical and physical mechanisms.

Jan 1, 1989

By Wilbur J. Morin

Construction of Flaming Gorge Dam in northeastern Utah necessitated the construction of a new state highway, Utah-260, to provide access to the dam and the town of Dutch John. A 550-foot arch structure was designed to span Cart Creek, about one mile southwest of the dam. The rock exposed at the site is highly fractured quartzitic sandstone with interbedded shale of the Precambrian Uinta Mountain Group. Eight exploratory holes were drilled, four in each abutment area, to determine rock types, the extent of fracturing at depth and rock strength. Drill cores in the west abutment revealed blocks of quartzitic sandstone loosened by the weathering and partial removal of underlying shale beds. The rock in the east abutment area was found to be highly fractured to depths of 70 feet and as far east as 50 feet from the footing locations. Selected core sections were tested for unconfined compressive strength but the values were not considered-representative of the in-situ fractured rock. To prevent movement along or, perpendicular to open fractures, four drilled-in columns were provided at the base of each footing. These extended 50, feet beyond the base of the footing, along the bearing and inclination of the thrust reaction.

Jan 1, 1963

By Joe D. Mitzel

The Indian Head fine has been in existence since 1922. For over 56 years there have been North Dakota people mining coal at this same location. The area affected will fit inside a circle 5 km in diameter, and the coal is lignite. The seam thickness has varied from 2.4 m to 3.65m, and the overburden from 6 m to 30 m in depth. me Lignite coal which is being mined at the Indian Head Mine is from 15.8 x l0 6 to 16.7 x 10 6 J per kg; it has a moisture content of 33 to 38%; an ash content of 5 to 10%; and a sulfur content of from 0.5 to 0.7%. The moisture content and the fact that we crush the coal co a top size of 14 cm x 0, are two of the characteristics or the product which cause it to freeze and remain inside of the railroad cars on the slope sheets. The market for the coal initially was almost entirely local coal sales. That is, coal was sold to people in the area who used the lignite to heat their homes, stores, offices, schools, and churches. Back in the early 1920's, there were no stoker-fed boilers, or pulverized fuel boilers, as we have in today?s marketplace. Basically, all of the coal was sold as lump coal, pieces about 30 to 35 cm square, to be used in furnaces: and nut coal with a top size of about 7.5 cm to 10 cm to be used in the old kitchen cookstove. All of the coal fines, less than 5 cm, were screened out and layed onto a pile. There was no market for the smaller sizes of the lignite coal. It has been our experience that when the coal is in lumps or chunks larger than 7.5 cm to 10 cm, there is a very slight possibility of freezing. That is the chunks themselves freeze, but by their nature, they do not cling to one another or form large masses of frozen material which are difficult to remove from the slope sheers of the railroad cars.

Jan 1, 1980

By G. C. Hambleton

There is sufficient indication of the existence of a basic misconception in the Coal Mining industry (on a world-wide basis) as to what computer control really does, what it costs, how it works and how and what it achieves as to make this presentation a welcome opportunity to present the case in what we hope is a simple, meaningful way. A plant cannot be said to be "automated" unless the control system has the capability to react automatically in accordance with predetermined programs under a great multiplicity of operational situations.

Jan 1, 1981

By L. Piga, G. Belardi, V. Alesse, N. Shehu, J. Freund

The physico-chemical interactions among minerals such as olivine, chromite and serpentine; the most commonly present ions in solution such as Ca and Mg; and flotation reagents such as EDTA and oleic acid were investigated. The study was conducted via release tests, electrophoretic measurements and microflotation of selected minerals coming from the Kukes deposit in Albania. The results were confirmed in beneficiation tests on two ores, one from the Kukes (Kalimash) deposit and the other from the Rizo deposit in Greece. It was demonstrated that, when Na-oleate is used as collector, chromite, olivine and serpentine can be separated at pH 2.5 and/or pH 5.5 when employing ethylenediamine tetraacetate (EDTA) on previously deslimed material. This approach ensures flotation concentrates with a Cr203 content better than 50% with a recovery of more than 75%.

Jan 1, 1998

By G. L. Hohmann

The Waste Isolation Pilot Plant (WIPP) project is authorized by legislation to provide a demonstration of the safe disposal of radio- active wastes generated by the national defense programs and activities of the United States. The U.S. Department of Energy (DOE) is proceeding with the implementation of the WIPP project in accordance with the "Department of Energy National Security and Military Application of Nuclear Energy Authorization Act of 1980" (PL 95-164).

Jan 1, 1982

By W. N. Key, L. C. Acton

Freeport Minerals Co.'s Ertsberg East underground operation typifies the cliche that all the "easy" ore deposits have already been found. Despite its location, in a remote Indonesian rain forest, and the effort and expense required to develop the ore body, the mine was developed on schedule, under budget, and with minimal disruption of the adjacent open-pit mining operation. Development of the Ertsberg East copper, gold, and silver ore body took less than two years after exploration drilling and feasibility studies were completed. In addition, the project came in well under its targeted budget of $101.5 million. Initial block caving and underground ore production took place last year. About 3 kt/d of Ertsberg's total 8.6 kt/d ore production is currently mined underground. This will increase to 5.4 kt/d by year's end. Underground operations will eventually account for all of Ertsberg's production, as the open-pit ore body is depleted. Freeport Minerals is currently studying the possibility of increasing total Ertsberg East production tonnage to 10.5 kt/d by 1983. The equipment, work practices, and development methods at Ertsberg East (Gunung Bijih Timur or "GBT"), while typical of other block caving mines, were modified for rapid mine development and maximum ore recovery. Located in the Irian Jaya province, "Gunung Bijih" is the Indonesian expression for the Dutch "Ertsberg" that in English means "ore mountain." "Timur" means "east" and relates to the fact that the new underground ore body lies about 1 km east of the open pit. The area surrounding GBT is mountainous, with peaks from 4.2-5 km. The underground mine adit and surface plant are located at a 3.6-km elevation. The mine, 4° south of the equator, gets 5.1 m/a of rain, but has an average daily temperature of only 13°C because of the mine's elevation.

Jan 7, 1981

By William G. Fischer

Basic laboratory tests initiated the. Rock Mechanics program. The stress-strain curve, modulus of elasticity, Poisson's ratio, the uniaxial rock strengths, Mohr's envelope, the stress at failure, and creep were investigated. A series of underground problems were then approached using this information; and various field measuring devices, most of which were developed by the Bureau of Mines. Initially, stress concentrations near mine openings were evaluated using the stress relief technique. This required an accurate determination of the pre-mining stress field. Later, stress concentrations associated with the cave line .sere studied. After about thirty stress reliefs over an appropriate time interval the effects of one type of mining could be compared against another. The microseismic technique was used to investigate a possible application of warning devices near the cave line. A study of mane reorientation was made Problems related to the shape and size of pillars and barriers were studied. Partial extraction mining systems were evaluated. The effectiveness of roof bolting patterns were examined. Control of roof stresses was attempted. A new system of mining in heavy ground has been developed using the information secured in the Rock Mechanics program without this system, mining in more than one instance would Nave been next to impossible. Indeed; from this one discovery alone, the Rock Mechanics program has paid off in improved safety as well as in dollars.

Jan 1, 1964

By A. G. Provost

On April 3, 1981, Harrison Western Corporation was awarded a contract by Amax Alloy - A Division of Amax Inc., to sink the Henderson #5 ventilation shaft. The project was located on the Henderson Mine site 88 kilometers west of Denver near the town of Empire, Colorado (Figure I). The Henderson No. 5 Shaft, located in an Alpine environment at an elevation of 3145 meters, was a 9.8 meter diameter concrete lined shaft with a total depth of 793 meters. Work started and continued with Harrison Western employees until January 15, 1982. At that time, Amax made the decision to continue the shaft-sinking with their own labor, and with Harrison Western providing supervision under a management service contract. Shaft sinking continued under this arrangement to October 1, 1982, at which time Amax put the Henderson No. 5 project on standby status until further notice.

Jan 1, 1986

By D. Puckett

The feasibility of maintaining equipment location, personnel location and vital statistics in surface and underground mining operations has increased with advances in radio frequency identification (RFID) technology. The paper addresses the use of this technology, relatively new in the mining industry, to track surface equipment in mine pits, loading points, and processing facilities. Specific applications are discussed including a simplified and a complex truck tracking system and an automatic pit ticket system. The paper concludes with a discussion of the future possibilities of RFID technology in mining, such as monitoring biofeedback of personnel (heart and respiration rate, body temperature, exertion level, etc.) repetitious movements to study work habits, and logging air quality via personnel sensors.

Jan 1, 1996