Search Documents

By M. R. Shahan, C. E. Seaman, S. E. Mischler, T. W. Beck

"Float coal dust is produced by various mining methods, carried by ventilating air and deposited on the floor, roof, and ribs of mine airways. If deposited float dust is re-entrained during a methane explosion, without sufficient inert rock dust quantities, this float coal dust can propagate an explosion throughout mining entries. Consequently, controlling float coal dust is of critical interest to mining operations. Rock dusting—adding inert material to airway surfaces—is the main control technique currently utilized by the coal mining industry to reduce the float coal dust explosion hazard. To assist the industry in reducing this hazard, NIOSH’s Pittsburgh Mining Research Division (PMRD) initiated a project to investigate methods and technologies to reduce float coal dust in underground coal mines through prevention, capture, and suppression prior to deposition. Field characterization studies were performed to determine quantitatively the sources, types, and amounts of dust produced during various coal mining processes. The operations chosen for study were a continuous miner section, a longwall section, and a coal handling facility. For each of these operations, the primary dust sources were confirmed to be the continuous mining machine, longwall shearer, and conveyor belt transfer points, respectively. Respirable and total airborne float dust samples were collected and analyzed for each operation and the ratio of total airborne float coal dust to respirable dust was calculated. During the continuous mining process, the ratio of total airborne float coal dust to respirable dust ranged from 10.3 to 13.8. The ratios measured on the longwall face were between 18.5 and 21.5. The total airborne float coal dust to respirable dust ratio observed during belt transport ranged between 7.5 and 21.8. INTRODUCTION During the extraction of coal, various dusts are produced that can be classified into two categories of interest: respirable and float coal dust. Respirable dust (diameter 10.0 = µm) has the capability to penetrate beyond the terminal bronchioles and become deeply embedded into the human lungs, leading towards respiratory disease complications (Potts et al., 1990). Float coal dust is defined as coal dust having a diameter less than 74 µm (Harris et al., 2009). During the mining process, float coal dust can be deposited on the floor, roof, and ribs of mine airways. With the proper mixture of methane gas (between 5% and 15%) and an ignition source, a methane gas explosion can occur (Barker and Humphreys, 1996). The resulting explosion can develop a pressure wave which lifts the deposited float coal dust material into the air, propagating a disastrous coal mine explosion (Harris et al., 2010). The current technique to safeguard against the propagation of a coal mine explosion is to treat the mine airways with incombustible rock dust (typically limestone), maintaining an 80% total incombustible content of the deposited material. NIOSH initiated a project to investigate control technologies that could be aimed at reducing the amount of float coal dust allowed to deposit in the mine airways using three approaches: prevention, capture, and suppression prior to deposition. Reducing the float coal dust being generated during the mining processes and capturing or suppressing airborne float coal dust prior to deposition would in turn increase the efficiency of the applied rock dust used to prevent mine explosions."

Jan 1, 2017

"With a longstanding reputation for engineering expertise, Weir Minerals continually develops solutions and technology to better serve the mining industry. Recognizing that throatbush wear rate has a major impact on the overall efficiency of slurry pumps, Weir Minerals has developed superior rotating and axial adjustment technology.In many applications, the pump’s throatbush is the component that has the shortest life compared to the impeller and liners, with considerable variability.Adjusting the gap between the throatbush and the impeller front shroud reduces hydraulic recirculation in the pump. This prevents localized wear on the throatbush, improves hydraulic efficiency and lowers the total ownership cost for the operator. To avoid impacting the plant’s production, these adjustments are often performed while the pump is operating. However, this can have safety implications for individuals working at the front of the pump unit.“Manually adjusting an alloy throatbush on a large pump requires several people and is laborintensive. It requires mechanical tools to adjust the four pusher bolts, one at a time, in order to reduce the gap between the throatbush and impeller. We wanted to find a safer and quicker way to extend the wear life of the pump with regular adjustments, which led us to development of this technology,” said Marcus Lane, global product manager for centrifugal pumps for Weir Minerals.“Our automated throatbush adjustment solutions are available for pumps fitted with either rubber or alloy throatbushes on Warman slurry pumps used in the most arduous applications, and have been designed with our customers’ safety and pump operation in mind. By mechanizing the adjustment procedure, personnel are removed from the line of fire, and the accuracy of axial movement is increased,” said Ron Bourgeois, director of slurry pumping technology group for Weir Minerals."

Mar 1, 2019

By S. J. Bluhm

INTRODUCTION Lesotho is a mountainous area of southern Africa from which water is to be exported in an extensive tunnel system, to industrial regions inland. The related tunnelling project has involved a num- ber of drives using tunnel boring machines [TBMs] to excavate about 100 km of 5 m diameter water tunnels [von Glehn and Bluhm, 1995). This paper describes the ventilation and cooling of some of the tunnel drives from both the operational and design points-of-view with a particular focus on heat generation. There were many common features in all of the drives but this paper is focused mainly on the Hlotse drive which was 18,4 km long. The drives were ventilated using forced ventilation systems to provide appropriate air flow throughout the tunnels and face zones. In addition, the Hlotse drive required refrigeration equip- ment which provided chilled water to the tunnel. While the sec- ondary ventilation systems play an important role in gas and dust handling, the paper concentrates on the primary ventilation and cooling issues. The ventilation of these tunnels was an exacting exercise be- cause: • Rock temperatures and geothermal heat flow were high. • TBMs with relatively high power ratings were used. • Diesel locomotives were used. • Drives were relatively long. • High altitude meant a low air density. An important feature was the simulation and monitoring of the ventilation and heat flow components and the project was characterised by analysis, monitoring and ongoing tactical decision-making throughout the progress. The thermodynamics of the systems were complex because there were many interactive effects and analyses were carried out using special computer pro- grams. The monitoring confirmed the accuracy of the models, and in this manner it was possible to confidently ensure healthy and safe working conditions and still minimise costs. Local ambient climate conditions range from temperatures higher than 35 "C in summer to below -10 OC in winter. Based on available statistical data and the thermal storage/damping effects in the system, design summer ambient conditions were taken as 15 OC/25 "C wet-bulb/dry-bulb. The barometric pressure was 80 kPa and due to the altitude, the ambient air density was only 0,9 kg/m3. The local Authority specified a maximum in-tunnel wet- bulb temperature [at any point] of 32,O OC and a mean wet-bulb temperature [from all locations] of 27,5 OC maximum. The maxi- mum height of ground cover above the tunnel was 1 200 m and the maximum virgin rock temperature was 41 OC; see Figure 1. Diesel dilution criteria specified by the local Authority was a minimum of 0.1 m3/s per rated kW of diesel engine. Other requirements related to gases such as CO, CO2, NOx and CH4 [and the need for intrinsically safe equipment] but these are not of direct relevance to this paper. The actual average face advance was about 30 m/d with good days achieving 60 m/d and good months achieving 1 000 m [23 working days]. The original design tunnelling rate was 50 m/d. DESCRIPTION OF HLOTSE DRIVE VENTILATION AND COOLING SYSTEM The ventilation requirements in the tunnels were dictated by heat and diesel dilution needs. The best ventilation and cooling policy is generally a balance between using increased quantities of fresh air or refrigeration [or both]. In this particular scenario it turned out that, since the diesel emission criteria required large quantities of air, the refrigeration needs were modest. The drive was ventilated using a ducted, forced ventilation system from fans located at the portal. The maximum ventilation requirement was 51 m3/s when the drive was at 18.4 km. From a heat flow point of view, the worst scenario was a heat load of 3.5 MW when the drive was at 7 km. This was cooled by the ventilation air and a supply of chilled water to the tunnel. Refrigeration and chilled water system In the design phase, a detailed comparison was carried out between two general alternatives for providing refrigeration. First, was a system in which refrigeration sets and air coolers are installed on the TBM train; the refrigeration sets are cooled by condenser water piped to and from cooling towers at the portal. Second, was a system in which refrigeration water chillers are in- stalled at the portal and chilled water is piped into the tunnel. The detailed comparison indicated that the capital and running costs of the second system were at least 60 % lower than the in-tunnel plant. There were also many obvious practical benefits for favouring the portal system. The refrigeration plant supplied 23 11s of cold water at a temperature of 10 OC. After providing the cooling effect in the drive, the water returned to the portal where it was initially cooled in open-circuit evaporative pre-cooling towers, chilled in the refrigeration plant and then returned to the tunnel. The cold water flowed into the tunnel in an insulated supply pipe and returned in an uninsulated pipe; the water was simply circulated to the end of the pipe and returned. The cooling effect in the tunnel was achieved entirely through heat transfer from the pipe [long linear heat exchanger] and no air coils or other heat exchangers were required. The cooling requirements were satisfied by the heat transfer to the returns chilled water steel pipe [200 mm]. The pipes were eventually installed to a maximum distance of 10,8 km in what was considered a very practical and cost effective solution.

Jan 1, 1997

By J. W. Leonard

By using physical and chemical method to increase the bulk density of newly mined coal, the productivity of a mine can be significantly increased. Greater amounts of coal can be placed in fixed volume shuttle car by increasing bulk density. This can increase mine productivity by about 15%. Small, easy to achieve changes in mining operations are required to obtain the increased productivity. This article deals with chemical methods used to increase coal bulk density, the results and discussion are based on experiments performed in the laboratory.

Jan 1, 1992

By R. K. Mehta

Stirred ball mill feed used for ultra-fine grinding application requires fine size separation step in order to avoid over-grinding. This paper presents the selectivity curves obtained for oil shale and complex sulfide are using 460 mesh (30 micron) Derrick vibrating screen. Interestingly, the selectivity curves generated from the experimental data were monotonic increasing selectivity for oil shale but not monotonic increasing for sulfide ore. These non-monotonic increasing selectivity curves were similar to the mechanical air separator fishhook selectivity curves described by Luckie and Austin. A 2 stage classification in series model describing the fishhook selectivity curve has been used in proposing the classification mechanism for fine vibrating screens when heterogeneous multicomponent sulfide are undergoes size separation.

Jan 1, 1992

By B. C. Lewis

The mining industry has experienced a general trend toward an increasing number of longwall operations, an increasing percentage of underground coal being mined by longwalls, and increasing productivity from the longwalls. Longwall operators have not yet reached a state of mining euphoria. Competitiveness both within the industry and from alternate fuel sources is forcing continued pursuit of higher productivities and lower costs. The following graphics present trends in the industry. Longwall mines, as defined for this presentation, are those reportedly having longwall installations in each of the respective years. Production from both the continuous miner and longwall units is included in the longwall mines. Non-Longwall mines are all other underground mines. Productivity calculations are based on total employee-hours associated with the operation.

Jan 1, 1990

By T. Skodack

This presentation will compare actual work site results for the loading and transport of shot rock for two major tunneling projects in North America. "SCARMAR" (the Canadian subsidiary of S & M Construction) is operating a rail bound Hagglund continuous gathering arm loader in combination with a Hagglund nine car shuttletrain system at the West End of Table Mountain on the B.C. Railway project near Tumbler Ridge, Canada. Al Johnson Construction is operating a Hagglund rubber tired continuous gathering arm loader in combination with haul trucks at the Rocky Mountain Pump Storage Project near Rome, GA. This paper will compare: 1) tunnel and ground conditions, 2) the total work cycle as it relates to mucking and haulage 3) efficiencies and related problems with the two systems 4) mucking and haulage rates 5) operating costs, and 6) recommendations for future large tunnel excavations. Manuscript not received in time for publication.

Jan 1, 1983

By Vincent T. Ricca

Acid mine drainage is a serious water pollution problem, for its contaminants will eventually effect the quality of the receiving streams. According to the Appalachian Regional Commission (1969)1, 10, 500 miles of streams have been polluted by mine drainage, and 70 percent of this acid pollution is accounted for by underground mines. Due to the severe damage to aquatic life, to recreational and industrial use, and to domestic water supply, more stringent mining and anti-pollution laws have been legislated and coal mine operators are required to treat the mine water discharges to meet the minimum standards. For years now, abatement and treatment methods have been extensively studied. Progress reports presented in the Fourth Symposium on Coal Mine Drainage Research, 1972 1 suggest that a thorough investigation and understanding of the basin discharge is necessary in order to cope with the mine drainage problem. The extent of mine water discharge contamination can be considered as a function of the basin streamflow and acid generation load.' A conservative treatment cost estimation these days is $0.40 per 1, 000 gallons for water with 100 ppm iron, 500 ppm acidity. These figures need not include collection and pumping costs nor the cost of dispersing of chemical waste by-products. To achieve optimal abatement and treatment of mine drainage, predictions of the quantity and quality of mine water discharges are needed. Basin discharge is a continuous process and it can be considered as a. macro-system. This system can be subdivided into micro-systems to describe the various mine discharge .types in the basin. The mining activities could produce acid water discharges from deep mines, stripmines, or associated gob piles. A total study entitled ?Resource Allocation to Optimize Mining Pollution Abatement Programs?* will consider all of these sources. However, this paper will discuss only one micro-system, the drift (deep) mine type. We will look at a single mine and its watershed. The total research project considers a multiple mining complex in an extensive stream basin.

Jan 1, 1973

By Z. Yunquan

The flocculation and dispersion behaviors of microsize wolframite and quartz are systematically studied in this paper. For synthetic mixtures, the floc separatory method on gravity units--electromagnetic vibration table (EVT) and lifting column (LC), have been approached. Satisfactory results can be obtained with a weak shearing. A better metallurgical performance can also be achieved for natural ore slimes through the combined technique. The efficiency is better than that of single gravity separation. Finally, the mechanism has been investigated.

Jan 1, 1990

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sulfur) coal which may be mined when the better deposits are depleted.

Jan 1, 1997

By D. Robert Weir

The complex mineralogy of the Porgera resource has a pronounced effect on process selection for the recovery of refractory gold and silver. Intimate association of gold with pyrite necessitates a high degree of sulphur preoxidation in order to achieve acceptable levels of gold recovery. Acid pressure oxidation has been demonstrated to be the only commercially proven process capable of achieving the required level of pyrite oxidation. Gangue mineralization dictates preconcentration of the sulphides to limit the acid consuming capacity and carbon dioxide generation during oxidation. However, the relationship between concentrate sulphur grade and gold recovery to concentrate ultimately governs the optimum degree of sulphide preconcentration.

Jan 1, 1986

By H. K. Lin

The free-milling ore characteristics of the Fort Knox gold deposit are ideal for studying gold and silver behaviors in various processing circuits without serious interference of sulfide minerals and other refractory factors. A galvanic effect leads to faster silver dissolution than gold dissolution and, as a result, the Au/Ag solution concentration ratio increases through the leach circuit. In the CIP circuit, Au adsorption is more effective than Ag adsorption. The Au/Ag solution concentration ratio decreases from 10.0 to 1.0 as the slurry advances from CIP tank #1 to CIP tank #5, while Au/Ag ratio in the carbon increases from 3.2 to 15.3, as the carbon advances from CIP tank #5 to CIP tank #1. Silver is stripped more effectively than gold from the loaded carbon. The Au/Ag ratio in solution reaches 2.0 in the first 75,700 L of strip solution that pass through the loaded carbon; as the stripping process continues, the Au/Ag ratio in the strip solution increases. In the electrowinning circuit, the Au/Ag ratio in the spent electrowinning solution is significantly lower than that in the electrowinning feed, indicating that Au is more rapidly deposited onto the cathode than Ag.

Jan 1, 2010

By A. Bhagwat, S. Tadolini

"Steel members of the ground support systems in underground mines are routinely exposed to corrosive environment that may range from acidic to alkaline. Corrosion of steel bolts leads to metal loss and thereby, reduction in strength and useful life. Protective coatings are commonly applied to the steel bolts to combat corrosion. However, coatings are expensive and often cumbersome in practical applications. Instead, Minova has developed an innovative technology based on sacrificial anodes. The anodes were designed from non-ferritic alloys that are inferior to steel on the Galvanic Series. This paper will present data from field testing to show significant benefit of the technology. Potential applications in current products will be discussed. INTRODUCTION Corrosion is a physical alteration of a steel material from electrochemical reaction with its environment that often results in reduction of the mechanical and physical properties of that material. Mine roof bolts, the subject of this investigation, are particularly susceptible to corrosion as they can be exposed in their working environment to ground water and air with high humidity. As other researchers have determined, corrosion increases markedly in sulfide ore bodies due to acid runoff. There are several types of corrosion that a rock bolt is likely to undergo when used for ground reinforcement in underground mines (Aziz et al., 2013). Of all the types of corrosion, pitting is particularly dangerous as it can remove capacity for the bolt to deform with subsequent strata movements. Sudden failure of a bolt is likely to occur when severe pitting corrosion is experienced. The type and nature of corrosion depend on the nature of the ground condition and bolt encapsulation. Generally, the type of corrosion and severity of the corrosion varies along the axis of bolt. Almost all of the mine roof bolts used in mines, with the exception of fiber reinforced polymers, are made from steel. The corrosion of iron is an electrochemical phenomenon with the overall equation:"

Jan 1, 2018

By Brett P. Spigarelli

"To meet the growing need for CO2 capture and storage technology, Michigan Technological University is studying CO2 capture using alkali-based solvents. The objective of the present study was to find a way to increase the absorption rate of CO2 into an alkali solution without reducing the absorption capacity of the solution. One approach to increasing absorption rate is to use a surfactant to chemically alter the gas bubble size. The surfactant chosen for the study was a neutral-charge polypropylene glycol methyl ether (PPGME) with a molecular weight of 200. Experiments were conducted to study the absorption rate of CO2 at varying surfactant concentrations. Results showed that as the concentration of PPGME increased in solution, the absorption rate also increased. The CO2 absorption rate increased from 3.45 x 10-3 mol/min CO2 at 0g/L PPGME to 3.92 x 10-3 mol/min CO2 at 0.48 g/L PPGME. This amounted to a 14% increase in the CO2 absorption rate with no decrease in the absorption capacity of the solution. IntroductionChemical absorption using an amine solvent is currently the most mature carbon capture and storage technology available. Amines are advantageous in that they have a fast CO2 absorption rate, which leads to a high CO2 removal efficiency. However, amine absorption has some considerable drawbacks, such as high energy requirements, high equipment corrosion rates, amine degradation in the presence of oxygen, high waste generation and a large increase in plant footprint if new equipment is constructed (Herzog and Golomb, 2004; D’Alessandro et al., 2010). Due to these drawbacks, Michigan Technological University (MTU) is studying CO2 absorption using alkali-based solvents, which address the above disadvantages of amine solvents."

Jan 1, 2015

By William Gleason

"Despite the difficult economic climate for the mining industry, more than 6,300 people joined SME for its 2016 Annual Conference & Expo in Phoenix, AZ, Feb. 21-24.Nearly every commodity has been bruised and battered during the past year, leading to one of the more difficult cycles for the industry in the past decade. Coal has taken some of the hardest hits and other commodities, such as copper and iron ore, have felt the sting of a slower growth in China and an oversupply on the market.The difficult conditions could not be ignored, but they did not deter SME from offering a forum for the industry to share knowledge, network with peers and learn about the best products and practices while visiting the sold-out exhibit hall (844 booths and 627 vendors) or while attending any of the 121 technical sessions that were offered.The current state of the industry was one of the overriding themes of the conference and during the challenging times there are often cutbacks as operations look to become leaner and more efficient, however, there is one area that cannot be cut – health and safety.The conference kicked off with a fascinating presentation from Colonel Mike Mullane, a former NASA astronaut who, in 1978, was selected as a Mission Specialist Astronaut in the first group of space shuttle astronauts. He completed three space missions and logged 356 hours in space aboard the shuttles Discovery and Atlantis before retiring from NASA and the U.S. Air Force in 1990.In his speech to a packed audience, he warned of the dangers of cutting corners to get the job done more quickly by guarding against the “normalization of deviance.”Normalization of deviance is a long-term phenomenon in which individuals or teams repeatedly accept a lower standard of performance until that lower standard becomes the norm. Usually, the acceptance of the lower standard occurs because the individual or team is under pressure (budget, schedule, etc.) and perceives it will be too difficult to adhere to the original higher standard. Their intention may be to revert back to the higher standard when this period of pressure passes. However, by getting away with the deviation from the higher standard, it is likely they will do the same thing when the same stressful circumstances arise again. Over time, the individual/team fails to see their actions as deviant."

Apr 1, 2016

By R. R. Klimpel

The use of froth flotation as a means of separating and upgrading sulfide mineral concentrates is standard industrial practice throughout the world. It is ap-parent from observing the industrial practice of sulfide mineral flotation over the last decade that progress is being made in optimizing the operating aspects of flotation. Examples of this are the availability of improved instrumentation and related computer control devices, the modification of mechanical flotation cell designs, the introduction of column cells, better reagent dosage control, blending of feed ores, increasing attention to coarse and fine particle separations, the successful introduction of new frother chemistries, etc.

Jan 1, 1989

By Ralph E. Weeks

Utilization of true in situ technologies for mining copper in Arizona will involve a complex environmental permitting process. This process is a key factor in determining the feasibility, costs, and implementing time frames required for development of this innovative mining method. The regulatory structure in Arizona is presently changing due to enactment of the Environmental Quality Act (EQA) of 1986 and development of new aquifer protection rules and regulations. The Bureau of Mines has reviewed the comprehensive hydrogeologic characterization, ground water monitoring, mechanical integrity testing, well construction, contingency planning, and other regulatory elements that will serve as mechanisms to assure protection of ground water resources. The purpose of this paper is to inform the domestic copper industry of the significance of the new Arizona regulatory structure and its implications for prospective in situ operators.

Jan 1, 1988

By M. S. Bickers

Prior to 1970, the environmental liabilities associated with mine construction and management were few. Mostly, they were aimed at health and safety matters. At that time less than two dozen codes were incorporated into the engineering design and they were somewhat static and well known by the engineering designers and managers. These codes issued by governmental agencies and professional associations are listed in Table 1

Jan 1, 1988

By B. H. Kim

The use of a 25.4 mm diameter water-only hydrocyclone for separating fine-size (-150 µm), high-density (>4.5 g/cc) particles from similar-size, lower-density (2.65 glee) particles was investigated. It was found that a single-stage separation recovered nearly 90% of the heavy minerals (7.0 g/cc), while achieving a volume reduction of about 70%. The use of dense medium in a single stage improved volume reductions to 90% at similar heavy mineral recoveries. In addition, computer simulations of a three-stage circuit were performed, which showed that recoveries approaching 97% with volume reductions of 95% were possible.

Jan 1, 1998

By B. R. Pothini, H. von Schonfeldt

In underground coal mining many excavated openings have a relatively short projected life span. To ensure safety for men and materials at a minimum cost over the projected operating life, only pillars for overburden support and roof bolts for support of the openings are used extensively. Mining activity constantly changes the geometry of the mine producing load changes on the structural support members of the openings that often induce unstable deformations which can lead to roof falls or pillar failures. The paper describes how simple deformation measurements can be used to design primary and supplementary roof supports and to predict roof falls and possibly pillar bumps. Specifically, bed separations in the roof measured directly with the help of borescopes and calculated from differential convergence data are used to optimize bolt links or support requirements for chemical stabilization of mine roofs. Roof falls are predicted on the basis of admissible values for cumulative convergence between roof and floor, convergence rate, and the change of the rate of convergence. The pillar extraction operations convergence anomalies detected from contouring identify bump prone pillars, while convergence and pillar dilation determine the yield zone in a pillar to verify pillar softening and de-stressing. Manuscript not received in time for publication.

Jan 1, 1983