Search Documents

By S. K. Kawatra

In most operating coal-cleaning plants, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. Reducing the pyrite recovery first requires that the primary recovery mechanism should be Identified, as different measures are required for reducing entrainment, locked-particle flotation, or true hydrophobic flotation. In this paper, evidence is presented which suggests that hydrophobic flotation is not an important mechanism for recovery of liberated pyrite from freshly-ground coal when the collector is a neutral oil, and that the bulk of the floated pyrite occurs either as a result of simple entrainment or by mechanical locking with floatable coal particles. Column flotation results are also presented which show that significant sulfur reductions can be achieved by reducing levels of entrainment.

Jan 1, 1992

By M. B. Haggerty, R. J. Sheets, F. Abbasy

To address coal refuse tailings storage needs for a mine operation in western Canada, a feasible solution was to convert excavated open pits into tailings cells. A slope stability investigation and design study were completed to determine the necessary width and slope geometry for in-situ native plugs as the impoundment embankment. The native plugs separate the previous open pit from the current active open pit. This configuration allows for the deposition of refuse tailings in the previous pit while allowing mining to safely continue “downstream” of the temporary impoundment. As mining progresses, each subsequent pit will be filled with refuse tailings; thereby, buttressing the upstream slope of the previous native plug. Although these cells are excavated, and the timeframe for downstream exposure is relatively limited, the native plugs are classified as dams and must be designed to meet applicable safety of dam standards since they impound water and tails above mining personnel in the subsequent open pit. The presentation and paper will discuss the investigation and analysis conducted to develop the geotechnical and hydrogeological design recommendations.

Mar 2, 2022

By Subhash Bhagwat

The definition of high sulfur coal varies from plant to plant and is subject to changes over time as the environmental regulations change. In plants constructed after September 1978 hardly any domestic coal can currently be burned without the use of Flue Gas Desulfurization (FGD) because a 70 percent reduction in potential S02 emission is mandatory even when the potential emission is less than 0.6 lbs. S02/106 Btu heat input. On the other hand older power plants may in many cases be legally emitting up to 6 lbs. S02/106 Btu or more under some State Implementation Plans (SIP). The Clean Air Act requires, however, that in the long run all stationary sources of S02 pollution must abide by the ceiling of 1.2 lbs S02/10 Btu heat input.. Coals with a potential to exceed this limit must, therefore, be considered as high sulfur coals. Such a definition would be unrealistic because many SIP's aim at an emission level of 1.8 to 2.0 lbs. SO2/106 Btu for existing plants and a stricter limit does not appear to be enforceable in the next 5 to 10 years. As a result, coals with an emission potential of greater than 2.0 lbs of S02 per 10 Btu heat input are considered high sulfur coals for the purpose of this investigation. Based on this definition and the 1984 actual consumption of coals by U.S. electric utilities (table 1) only 7 out of the 24 coal producing states could be categorized as low sulfur states. The actual S02 pollution, however, depends on total tonnage of a type of coal as well as the sulfur content of the coal. Table 1 also indicates that only 6 states--Kentucky, Illinois, West Virginia, Ohio, Pennsylvania and Indiana-account for nearly 77 percent of S02 pollution potential in the United States. These 6 states have therefore been chosen for this investigation.

Jan 1, 1986

Geostatistical literature has been dealing with recoverable reserve estimation techniques for the last 30 years. There have been well established support correction techniques (Le. affine correction, indirect log-normal correction, etc.) to deal with volume -variance relationship globally in determining what will be the reserves above a cutoff grade during mining. Kriging has become the accepted technique in the mining industry for ore reserve estimation. Many large companies are using this method for gold and copper deposit modeling. In general, the estimates coming from kriging are smooth. The variances of the block grades estimated by kriging are often lower than the material that will be mined selectively. As a result, kriging tends to under estimate reserves at high cutoff grades and overestimates them in low cutoff grades. It is necessary to perform additional steps after kriging if the goal is to determine recoverable reserves at some cutoff and not the in situ resources. In the mining industry, it is becoming more and more common for the low grade heap leach projects to consider whether the higher grade portion of a deposit may be processed by a mill at higher profits. Similarly, a concentrator -refinery operations are implementing heap leach -SX-EW option for the lower grade portion of their deposit. These options are making it very critical to estimate the low and high end of the grade distributions more accurately. Ore reserve estimation is normally done by using widely spaced exploration data which has very small size support (Le. core samples). Selective mining is carried out on ore control that is based on closely spaced blasthole data normally averaged into larger polygons based on some cutoff grade. Estimated grades from exploration data need to reflect the variability of the grades of the selectively mined units if they are used without further adjustments to predict recoverable reserves.

Jan 1, 1997

By K. Ueda

Lead concentrates from Kuroko (black ore) mines, which contain Cu 4 ? 7%, Pb 55%, Zn 3 - 7%, As 0.5 - 0.9% are treated by hydrometallurgical process in order to smelt the product by electric furnace smelting together with other lead resouces from Kuroko. The hydrometallurgical pretreatment involves sulfuric acid leaching at first stage, ferric leaching at second stage. This paper describes the short history of lead recovery from Kuroko and the performance of laboratory test, pilot plant and commercial operation.

Jan 1, 1982

By James T. Baxter

Underground mining of limestone is becoming increasingly attractive in Illinois. Most quarries are near rivers on the western and southern borders where competition for land use is intensive. Increasing demands for stone can be met by expanded mining with access by edits in existing quarries and by inclines and shafts at downdip sites. Geologic, hydrologic, and engineering conditions indicate that deep mines in the Ste. Genevieve, St. Louis, Salem, Ullin, and basal Burlington Limestones of Mississippian age and in the Moredock Limestone Member of the Dunleith Formation of Ordovician age are possible, but development will require prudent exploration and planning to ensure that the product will be of good quality.

Jan 1, 1978

By K. Louk, E. Gilliland, N. Ripepi, M. Karmis

"Carbon dioxide (CO2) injection in deep unmineable coal seams can enhance coalbed methane (CBM) recovery as well as effectively and permanently store the CO2. Enhanced coalbed methane (ECBM) recovery and CO2 storage capacity can be improved by altering injection parameters including the injection well locations, number of injection wells, and the time and rate of the injection. A sensitivity study was performed with sixteen different injection scenarios on a coalbed methane field in Buchanan County, Virginia to understand the influence of the injection parameters on methane production, CO2 storage and the extent of the CO2 plume. History matching was done for the gas and water production period prior to injection based on field data from an active US Department of Energy funded pilot project. INTRODUCTION The coal structure is a combination of the coal matrix and cleats. In a CBM reservoir, the methane (CH4) is stored in the matrix under adsorption properties, not as a free gas. During CH4 production, the reservoir pressure is reduced and gas is released from the surface of the coal, diffuses through the matrix and transmits to fractures (man-made or natural) via the cleat network. Fractures and cleats are the major parameters that influence gas flow capacity because deliverability of the CH4 to the production well is controlled by the cleat permeability. As gas production continues over time, CH4 desorbs from coal, and coal matrix volume starts to decrease. This volume decrease in the matrix opens up the cleats, matrix shrinkage, which leads to a permeability increase. Several emprical (Harpalani and Schraufnagel 1990a, 1990b; Harpalani and Chen 1995, 1997; Harpalani and Mitra 2010; Pan et al. 2010; Liu et al. 2012; Mitra et al. 2012) and analytical (Palmer 2009; Liu and Harpalani 2013) studies have reported this relationship between pressure and permeability. Those studies showed that permeability is an important parameter in CH4 production performance. Furthermore, during gas production, water is produced through the cleat system as well, therefore gas-water relative permeability must be also considered in evaluating production performance (Gash et al., 1991). In the CO2 injection scenario the opposite occurs because CO2 has a higher adsorption affinity than CH4. CO2 replaces CH4 in the matrix of the coal and increases the volume of the coal matrix, matrix swelling, and results in a permeability decrease. Harpalani and Mitra (2010) concluded in their experimental study that swelling of the coal matrix due to the CO2 injection is two to three times more than the sorption of CH4, resulting in large permeability changes during CO2 injection."

Jan 1, 2016

By Gary A. Nowlan

The Casa Grande West-Santa Cruz porphyry-¬copper deposit is in the Basin and Range physiographic province west of Casa Grande, Arizona (Fig. 1). The Casa Grande West portion of the deposit is controlled by Casa Grande Copper Company and the Santa Cruz portion by ASARCO. The deposit contains at least 350,000,000 metric tons of rock with greater than 1 percent Cu. The deposit is covered by at least 300 m of sediment, with no visible expression of the deposit at the land surface. The deposit is in an area of prime agricultural land that depends heavily upon well irrigation because of a hot and arid climate. Because of the deep sedimentary cover, the chance is extremely remote that the geochemistry of soil or stream sediment would reflect the deposit even if the land surface were not disturbed by many years of farming. Irrigation wells of the area generally bottom in the sedimentary cover. The purpose of the study is to see if the Casa Grande West-Santa Cruz deposit is geochemically reflected in ground waters over and near the deposit.

Jan 1, 1981

By Chester O. Ensign

The White Pine Mine is situated in the southwestern portion of the Keweenaw Peninsula of Upper Michigan approximately 6 miles south of Lake Superior (Fig. 1). It is east of the Porcupine Mountains in Ontonagon County. The ore deposit is about 70 miles southwest of the famous native copper deposits of the "Copper Country" lying northeast of Houghton. Geological conditions are different at every mine and create a special set of problems in dilution control. This paper is largely intended to describe the techniques applied in mine dilution control (grade control) at White Pine, and present results of the program. For necessary background information major geologic characteristics of the deposit, particularly those that exert control over the distribution of ore, are briefly discussed. Mining methods are described in considerable detail since applied grade control techniques are adapted to these.

Jan 1, 1964

By Alexander N. Winchell

The cities of St. Paul and Minneapolis are located side by side on a double loop in the Mississippi River near the eastern boundary of Minnesota. Both cities lie on both sides 'of the Mississippi River, which in this region describes an S-shaped curve. The two cities together have a population of over 600,000 people, gathered in an area which has grown to be a single urban district inasmuch as the two cities have expanded until they occupy all the territory formerly between them, though the business centers are ten miles apart. St. Paul is located at the head of navigation on the Mississippi River and Minneapolis, farther upstream, at the Falls of St. Anthony. A recent water¬power development below the Falls of St. Anthony, constructed by the Federal Government, has at the same time made possible navigation to the foot of St. Anthony Falls through a lock around the dam which replaces the former rapids. Minneapolis, in 1920, had a population of 380,000 people, and St. Paul, 235,000. The two cities occupy land at an elevation of 700 to 900 feet above sea level. The average elevation is slightly less at St. Paul. Minneapolis has nearly 4,000 acres of parks and park¬ways, while St. Paul has nearly 2,000.

Jan 1, 1920

By J. C. Rhodes

The demand for good white minerals for many industries including paint and plastics have made it necessary to import high grade industrial minerals from various parts of the world. Some of the calcium carbonate, barite and talc minerals are from China, Mexico, Jamaica and Haiti. These materials can be processed by custom processors. The custom processor can provide a service to the Industrial Mineral owner. The imported materials can arrive in various feed sizes from lumps (3"-6") down to 325 mesh. The materials can also be in various size shipments or container loads. The economics for importing should be investigated thoroughly. The two factors just mentioned can influence the quantity of material to be processed. These two factors can also influence the total cost for each end product.

Jan 1, 1989

By J. Baz-Dresch

A custom-designed shotcrete system, consisting of an 8-m3 (10-yd3) transit mixer and a shotcrete spray boom carrier, is used bya 2-man crew to transport and place up to 25 m3 (32 yd3) of steel-fiber reinforced, dry, silica fume shotcrete per II-hour shift. Shotcrete is custom blended by a local supplier and delivered predampened. Mix design and quality control is performed with a computer program that develops and graphs a properly balanced mix based upon the materials sieve analyses.

Jan 1, 1991

By Tomek Ulatowski

This article discusses four principal areas relevant to financing direct reduction facilities: (1) Lenders' differing requirements with respect to projected cash flows; (2) The impact of leveraging on project viability; (3) The importance of appropriate debt structure; (4) The significance of accurate and complete capital cost estimates. The overall findings emphasize the inseparable connection between the project economics and its financeability, and particularly how direcly intertwined they both are in the project planning.

Jan 1, 1978

By V. D. Smar

The flotation process may be considered an interactive system consisting of many chemical, operational, and equipment variables. Changing anyone of these variables causes an overall system response change. This study examines the effects of simultaneously changing the operating variables of: (1) frother concentration and air flow rate, and (2) frother concentration and collector concentration. It is part of a comprehensive study to look at how changes in several of the major variables may be used to produce interactions which will allow the rougher flotation process to be optimized. Ultimate recovery, flotation rate, concentrate grade and froth quality, are used as the major evaluative criteria.

Jan 1, 1993

By V. T. McLemore

The Steeple Rock district is a major epithermal .gold-silver district in New Mexico that exhibits district zoning. Five types of ore deposits occur in the district. The base-metal veins (with Au and Ag) form the center of the district and occur along the Carlisle fault. The gold-silver veins occur along northwest-trending faults outward from the base-metal veins. The margins of the district are formed by copper-silver, fluorite, and manganese veins. In addition, areas of older acid-sulfate alteration occur throughout the district and also exhibit zoning: massive silica/chert zone (inner), silicified zone, and clay zone (outer). This alteration overlies regional; alkali-chloride (propylitic to argillic to sericitic) alteration. Synthesis of available data suggests the acid-sulfate alteration is related to a shallow but older epithermal hot springs system. Subsequently, younger epithermal veins formed along faults.

Jan 1, 1994

By Leandro Seixas Bicalho, Wagner Cláudio da Silva, Kelly Laranjeira Nunes, Lívia Marques Faustino

Seeking to implement the Global Industry Standard on Tailings Management to improve the safety of their tailings facilities across the globe, mining companies are motivated to invest in new technologies to recover valuable minerals from tailings. One solution being evaluated is the use of magnetic separators to concentrate ultrafine tailings. However, this approach is energy intensive as it requires high magnetic fields to recover ultrafines, and usually results in low mass yields. Additives that modify pulp rheology and surface properties, or selective flocculate ultrafine particles, were tested to enhance the performance of magnetic separation. Promising results in laboratory scale testing different types of additives confirmed that it is possible to increase the mass yield, keeping the selectivity of this stage.

Feb 1, 2024

By Harry Elkin

Control of coal dust has long been an important aspect in the conventional mining of coal; the main reasons being from a health and disaster standpoint. With the advent, of mechanized longwall mining, the control of dust has required more attention due to the high extraction rate common to most longwall systems. The purpose of this paper will be to describe the dust abatement activities of the longwall operation at Sunnyside. Kaiser-Steel Corporation has three mires located at Sunnyside, Utah, with a total production averaging 6,800 tons of clean coal per day. Of this 6,800 tons, 71 % is mined with continuous miners, the remaining 29% coming from one longwall unit located in No. 3 Mine. Our first longwall panel was started in November, 1961. In October, 1966, we started mining our seventh panel. The present panel is located in the Upper Sunnyside Seam which averages five feet in thickness, but does get as low as 51 inches. The seam pitches 5.5% in this vicinity. The roof is generally good and is comprised of 10 inches of shale cap rocs overlain with sandy shale and sandstone. The floor is sandy shale and is quite undulating in nature. The present panel is 3,800 feet in length with a face of 670 feet. The major equipment employed on our longwall unit is a 125 H.F. Anderton Shearer-Loader, British Jeffrey Diamond armored conveyors and a Dowty self-advancing-roof support system. The Anderton Shearer in use on our longwall unit has a 60" diameter x 27" cutting drum. During the shearing cycle, it traverses the face at 20 feet per minute with a cutting rate of 7.5 tons/minute.

Jan 1, 1967

By İlknur Erol

The abstract highlights that hearing loss is an occupational disease caused by noise exposure in the workplace. The study investigates noise-induced hearing loss among miners in underground coal mines in Turkey, considering factors like occupation, age, and exposure time. The research employs logistic regression analysis to reveal the relationship between hearing loss and these factors. The findings suggest that occupational groups and duration of noise exposure significantly affect hearing loss. Miners in production groups and those exposed to noise for 10-14 years have a higher risk. The study concludes that age does not significantly increase the probability of hearing loss.

Mar 24, 2022

By John A. Wolfe

The concepts of sea floor spreading and plate tectonics provide more logical explanations of some geologic processes than were possible a few years ago. I plan to premise my discussion of the regional features of Philippine porphyry copper deposits on this tectonic basis, recognizing that parts of the picture can be explained in other ways, but in the belief that this is the best explanation of the whole. The sequence of events which results in the formation of Porphyry deposits (Figure 1) can be summarized as the result of collision of crustal plates, subduction of the oceanic plate, emplacement of a serpentine ultrabasic diapir, formation of a dioritic magma at depths of 300 to 500 km, rise of the magma to a sub crustal or intra-crustal chamber, eruption of andesitic volcanoes, emplacement of diorite or differentiation of the magma into more acidic products, multiple intrusion of hypabyssal rocks and hydro-

Jan 1, 1973

By Jeff Easton, J Johnson, D. Foot

The Mina Santa Rosa mine in Panama was the victim of a mine closure 24 years ago that left the community in dire straits. The mine showed the potential resources of greater than 1M ounces of gold and 4.5M ounces of silver. Veragold Mining Company decided to reopen the mine and address all the issues that were involved in the startup of an historic mine. This paper provides methods to restore the community trust, provide a transparent process, and develop an environmentally sound flowsheet. Immense scrutiny surrounded the Tailings Storage Facility, and the company developed a plan focused on paste thickening and surface stacking to eliminate the need for a conventional tailings’ facility. Paste thickener principles and benefits are also provided.

Feb 1, 2024