Search Documents

By S. G. Zahony

The Moris gold deposit resides in a massive ridge-forming sulfide-poor epithermal quartz and calcite vein system and consists of a mineable reserve of four million tons of 2.1gm Au/ton. Post-mineral normal faulting along the hanging wall of the main fissure has caused a hogback-like exposure of the vein, allowing for inexpensive opencut mining. The vein formed between pre-Cretaceous(?) phyllitic clastic sedimentary units in the footwall and Tertiary andesitic volcanic rocks in the hanging wall. Part of the ore reserve is hosted in a Tertiary conglomerate that rests unconformably atop the phyllitic footwall sequence. The original unoxidized vein material contained substantially less than 1 gram Au/ton. A four-fold upgrading of gold occurred by enrichment when gold recrystallization took place in the electric fields of oxidizing pyrite cubes.

Jan 1, 1993

By Courtney Chamberlain

The Telfer Project, Australia's newest, largest and most remote gold mine, treats 480,000 metric tonnes of ore grading 9.33 grams per tonne derived from open pit mining operations. Coarse gold is recovered by gravity concentration with jigs and further upgraded using a continuous strake, table and by amalgamation. Remaining gold is recovered in a cyanide circuit and incorporates flat bottom air agitators, CCD and stellar filters for clarification and precipitate removal. Overall recovery into bullion averages 98 percent. The mill incorporates a number of design features which allow for maximum efficiency and security using a minimum number of operating personnel.

Jan 1, 1980

By William W. Magnus

The Eastern Magnesia Talc Company has always had the problem of adequate storage at its various mines and mills of not only crude ore and finished product but also material in process. An opportunity arose a couple of years ago with the decision to build a new mill at West Windsor, Vermont, (Figure 1) to come as close to providing adequate space for ore and the ground talc in the new plant as money and judgement would allow. Since our engineering staff did not have the time to design and engineer the new facility, an architectural firm with complete engineering staff was retained. Our original thought was to contract all phases of the construction and installation, however, and I think this is a most important point for any small firm such as ours, we found that with good supervision we, as the contractor, could do the job faster and at a lower cost than the construction firms that bid on the work. For some 50 odd years Italian talc has had a virtual monopoly in the body powder area of the cosmetic industry. Due to the purity, superior lubricity and whiteness, naturally occurring in the talc from Italy, no talc in the Western Hemisphere could capture any but a very small part of the market. When the Italian supply was cut off during World War II, the United States' largest consumer of this talc decided that it was time to develop a domestic source of a satisfactory replacement.

Jan 1, 1965

By M. Shriwas, F. Calizaya

"Recirculation is prohibited in many coal mining countries because of the fear that the re-use of return air would allow the build-up of air contaminants at the workings. The incorrect design and location of a booster fan in any ventilation network can create unsafe condition due to recirculation. The current approach to investigating recirculation using simulation software requires manual effort which becomes tedious in a complex and a large network. An algorithm-based C++ program was designed to detect the recirculation in a booster fan ventilation networks. This program needed an input file prepared from output file generated by any ventilation simulator. This program created an output file for recirculation. This program demonstrated the strong capability to detect the recirculation in a sample network and a coal mine ventilation network. The outcomes of this program were documented in this paper. INTRODUCTION The proper design and location of booster fans eliminate the safety hazards associated with high main fan pressure. Conversely, the incorrect design of booster fans in any ventilation network can create unsafe conditions due to uncontrolled recirculation. The proper utilization of a booster fan derives benefits to reduce the main fan pressure, leakage, and consequently ventilation cost especially with high resistance network due to deep and extensive working area in a mine. However installation of booster fan may create uncontrolled recirculation, if it is not sized and located properly with respect to main fan. Recirculation is prohibited in many coal mining countries because of the fear that the reuse of return air would allow the build-up of air contaminants at the workings. Therefore, it is imperative to check the recirculation while designing and operating booster fan for a ventilation network. This paper deals with an algorithm based C++ program to detect the recirculation in a booster fan ventilation networks. This program was implemented to detect the recirculation in a sample network and a coal mine network. STATEMENT OF PROBLEM The currently available ventilation simulation programs do not give much information about recirculation for the generated solution (fan pressures). The current approach to investigating recirculation using simulation software requires manual effort, i.e., traversing from node to node in the output network by the simulator while keeping tracks of all the nodes that form recirculation paths. This is an easy task in a simple ventilation network, but it becomes tedious and sometimes very confusing in a complex and large network. Moreover, the presence of multiple recirculation paths makes the manual effort more complex and difficult, especially in separating multiple loops that are connected together. Thus, there is a need for a more efficient program that will detect and quantify the recirculation efficiently, for the generated fan pressures. A program is developed to detect the recirculation(s) in a network."

Jan 1, 2015

By R. Venugopal, V. K. Saxena, Veerendra Singh

"Ore morphology plays a vital role during the milling and liberation of minerals. This study was carried out to understand the role of mineral crystallography and mineral interfaces on the milling and liberation processes. Data related to mineral crystallography, Vickers Hardness Number and beneficiation processes were collected from literature, and detailed statistical analysis was conducted to relate these parameters. Review of the crystallographic information of minerals present in ores indicates that molecular weight and cell parameters significantly affect milling and liberation characteristics. Mineral interfaces were classified into the three categories of coherent crystals, semi-coherent and incoherent crystals, and breakage behaviors were studied. The studied cases revealed that these material interfaces control the micropore properties that play a vital role in the initiation of intergranular and intercrystalline fractures which occur in siliceous manganese ores and dolomite as a result of thermal treatment. In contrast, banded hematite jasper and coal exhibited a much more complex fracture pattern due to their coherent interfaces and finer physical associations. This study explains the effect of the various types of interfaces on milling, and the approach can be helpful in developing a methodology to enhance mineral liberation with minimum energy consumption.IntroductionComminution is a vital unit operation in the mineralprocessing, cement-making, power-generation and pharmaceutical industries. Its importance in mineral beneficiation operations is increasing every year as a result of the growing need to exploit lower-grade ore bodies and process reject materials (Blazy et al., 1994; DOE, 2005). Low-grade ores require significant energy during grinding to liberate the valuable minerals, which are further separated from the gangues by various beneficiation methods. Various attempts have been made to enhance mineral liberation during grinding to minimize energy consumption. Most of these studies focused on the analyses of the compression mechanism, chemical additives, thermal treatment, microwave treatment and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Bearman et al., 1997; Kumar et al., 2010; Wang et al., 2011; Singh et al., 2012). However, many of these efforts had limited success, and there is a need to see the problem from a fresh perspective."

Jan 1, 2015

By Jacob Grasmick, Bill Newns

Despite ongoing digitization and “hardware” technological advances, geotechnical uncertainty remains the most significant risk in underground and tunnel construction. And, whilst they are commonly held up as an example of the sophistication of the industry, the practice of drafting and using geotechnical baseline reports is subject to a wide range of influences, not all of which support good risk management. Uncertainties in predicting ground behavior, the gap between the pre-construction assumptions, and the systemic response to construction remains a significant technical and communication challenge. Accordingly, this paper presents a framework to quantify geotechnical uncertainty using geostatistics and translate these into practical tools for ground risk management throughout planning, procurement and construction. Adopting even some of the principles of this framework should provide improvements to contract risk management and should assist to minimize the potential for commercial losses.

Dec 1, 2022

By John W. Trammell

The White Pine Mine is situated in Ontonagon County, approximately six miles south of Lake Superior, in the Upper Peninsula of Michigan (Figs. 1 and 2). The ore body mined by White Pine Copper Company occurs in the lower - most 20 to 25 feet of the Nonesuch formation, a series of middle - to upper Keweenawan shales, siltstones, and sandstones. This paper elaborates on the solution of problems in ore grade control and mine planning arising from the presence of an essentially barren sandstone stratum within the ore body.

Jan 1, 1964

By Gary G. Grim

The reliable performance of the coal reclaim system is essential to the continued availability of a coal-fired electric generating unit. The control of fugitive coal dust within the areas housing the reclaiming equipment is necessary not only to minimize maintenance and clean-up costs, but is also a safety and health consideration. This paper describes the reclaim system control and dust suppression systems as initially installed, the shortcomings of these systems and the steps eventually taken to correct these shortcomings.

Jan 1, 1983

By L. Gutierrez, J. S. Castro S. Laskowski

Water is a medium in which flotation takes place, and flotation efficiency is highly dependent on water quality. Of the total water resources on Earth, less than 2.5 percent is fresh water. This water is used in agriculture, by households and by industry. Among the industrial users of fresh water, the mining industry occupies an important position. Furthermore, mining operations are often located in arid areas with very limited access to fresh water. The demand for and shortage of water in these parts of the world, such as the Atacama Desert in Chile, makes the use of seawater by the mining industry the only sustainable solution. 

By Louis W. Towle

A brief history of the use of Ammonium Nitrate in explosives and blasting agents is given. Methods of manufacture and physical properties of the various types of Ammonium Nitrate are given with particular reference to their use in blasting agents Important properties of blasting agents discussed are sensitiveness, methods of initiation, velocities of detonation, strength, density, products of detonation, rate of pressure development, and borehole pressure.

Jan 1, 1959

By Irwan Halim, Stephane Polycarpe, Brian Hann

The Narragansett Bay Commission Phase III CSO Program includes construction of the 11,600-foot long, 30-foot ID, deep rock Pawtucket Tunnel in Rhode Island. This paper provides an overview of the Design Build Project features and highlight some of the important design considerations, features, and innovations, including geologic conditions and related TBM design, and deep shaft and tunnel segment designs. The paper provides the most recent updates on some of the project construction activities including TBM tunnel progress and retrieval schemes, tunnel pump station and deep vertical shaft liner installations, SEM construction, and microtunneling for the longest adit using Fiberglass Reinforced Polymer Mortar pipes.

Jun 23, 2024

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey’s test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

By Levent Ozdemir

An extensive study involving laboratory testing and computer modeling has been performed to assess the technical and economic feasibility of utilizing the recently developed minidisc cutters on roadheaders for hard rock mining. The results show that heavy duty roadheaders fitted with minidiscs can excavate hard rock formations at acceptable production rates and cutter costs. This paper presents and discusses the results of this study together with the ongoing developmental efforts of this technology, which include laboratory testing of a roadheader cutting drum with minidiscs and full scale field testing of a machine in hard rock

Jan 1, 1995

By Hassan El-Shall, El-Sayed A. Abdel Aal

The major goal of this study is to decrease iron content in wet-process phosphoric acid. Reducing the amount of post-precipitated sludge in the acid is another important objective in this investigation. In order to achieve these goals, research efforts have focused on bench scale testing of an iron-chelating reagent to remove iron from phosphoric acid produced from South Florida high-iron and -magnesium phosphate concentrate, and plant testing using freshly produced concentrated acids for reducing the post- precipitated sludge. The data obtained in the above studies suggest that the addition point of the precipitating reagent is very important, as the precipitated iron compound has higher solubility at higher P2O5 concentrations. Up to 60% Fe2O3 removal efficiency is achieved depending on the amount of the reagent, concentration of acid used, and operating conditions. The addition of precipitating reagents to freshly concentrated phosphoric acid leads to a decrease of up to 84% in sludge volume percentage depending on acid type and clarification conditions. Decreasing the volume percentage of the sludge facilitates acid handling as well as decreases the adherent water- soluble P205 leading to lower total P2O losses.

Jan 1, 2002

By Brian Gettinger, Jared Barber, Richard Weatherly, Shannon Dunne, Jeff Masek, Chuck Wolf, Fazle Rabbi, Jack Canfield

During Hurricane Harvey over 60% of the 39 WWTPs, including the low-lying 25 MGD Sims North WWTP, and one third of the 382 lift stations owned and operated by the City of Houston were flooded resulting in extensive facility damage, loss of service and uncontrolled release of untreated wastewater into bayous and creeks. In response, the City has embarked on an effort to improve system resiliency by consolidating at-risk facilities with a network of deep sewer tunnels. These tunnels will provide secondary benefits to the collection system of augmenting the capacity of the existing 6,000 miles of sewer mains and lowering the collection system profile in poor performing areas. Investigations on the cost to mitigate the flood damages by raising the liquid stream processes at the Sims North WWTP is estimated at nearly $450 million. Instead of spending $450 million to raise the plant, the funds will be directed to providing a more robust and resilient wastewater system for the Sims basin area of Houston. The backbone of this new system is a 4.5-mile-long, 110 inch diameter deep gravity sewer tunnel that will convert a system heavily reliant on distributed lift stations to a majority gravity system with a deep consolidated lift station at the Sims South WWTP. This will also allow the City to address the flood prone infrastructure at Sims North and consolidate its operations into a single permitted outfall for this collection system. This approach is the outcome of a team effort focused on maximizing system resiliency and sustainability for the next 100 years. By thinking outside the box, the City of Houston will not only mitigate the flooding risk at Sims North WWTP, but also solve regulatory and operational challenges throughout the sewershed and deliver a winwin on multiple levels.

Jun 13, 2021

By Chi-shing Wang

In many cases the roof strata of a bedded deposit may be considered as a composite of rock beams of rectangular cross section, whose component layers differ in thickness and may or may not be separable from each other when they are subjected to loading by their own weight. An analytical study of the behavior of such multiple-layer beams is extremely difficult owing to the heterogeneity and anisotropy of rock materials. The complexity is revealed by the fringe photographs obtained from several series of barodynamic photostress experiments conducted on various types of multiple-layer model beams of a medium-grained Bedford limestone. Further discussion on the applicability of barodynamic photostress techniques to the model study of the behavior of mine roofs in stratified geologic media is presented by comparing the phenomenological observations recorded in this investigation.

Jan 1, 1968

By David J. Hatem, K. Bhattarai

Effective risk management in major subsurface projects involves ways to mitigate adverse impacts to final design and construction approaches due to changed subsurface conditions. An Early Contractor Involvement (ECI) collaborated with Observational Method will be an effective contractual tool to address risk developed due to encountering differing site conditions. Observational Method (OM) can further be supported with artificial intelligence (AI) technologies with automated data-driven decision-making features in risk mitigation and implementation of proper design and construction approaches. This paper presents collaborative applications of ECI, OM, machine learning, and risk baselining in risk management and productivity enhancement in tunneling projects.

Jun 23, 2024

By R. F. Hadley

Alluvial valley floors constitute a valuable land resource and have been important to ranching operations in semiarid western United States. This resource may be in jeopardy locally if the alluvial deposits are disturbed by surface mining of coal deposits. Erosion problems caused by poor land-use practices can cause trenching of the unconsolidated alluvium with a consequent lowering of the water table and depletion of soil moisture needed to support vegetation. Historical evidence of this sequence of events is abundant in geologic literature and serves as the basis for assessing potential impacts of surface mining. The potential geomorphic impacts of surface mining on alluvial valley floors with regard to fluvial processes are: (1) disruption of the longitudinal profile followed by valley trenching and high sediment yields downstream and (2) replacement of the excavated alluvium with unconsolidated material that does not have similar physical characteristics and may be susceptible to erosion. Mining may disrupt the existing hydrologic framework affecting streamflow, ground-water levels and water quality of both surface water and ground water. Although functional hydrologic and geomorphic processes are similar, each valley represents a complex environment that does not submit to broad generalizations.

Jan 1, 1978

The 86th Annual Meeting of the SME Minnesota section/74th Annual University of Minnesota Mining Symposium partnered with the Canadian Institute of Mining Metallurgy and Petroleum (CIM)?s Iron Ore Symposium for a historic joint conference, held this year in Duluth, MN, April 15- 17. One of a flurry of recent collaborations between SME and CIM, the joint conference was a natural fit for the conference held in the heart of the Iron Range. As CIM National President Terence Bowles said in his joint keynote with SME President Jessica Kogel, ?The U.S. imports $51 billion from Canada and Canada imports $38 billion the U.S.; that?s 50 percent of Canada?s exports and 51 percent of its imports.? The two countries? economies are linked, and nowhere more closely than in their iron ore mining activities. Kogel opened the conference with a plenary speech identifying the top 10 issues facing mining and how these issues present opportunities for mining companies. She said that it is important that the mining industry stay flexible and adapt to changing conditions, or it will go the way of the dinosaur. However, she said that these challenges can lead to new opportunities. For example, one of the major challenges facing mining is the current state of risk aversion among investors, which makes for ?less money in the pipeline.? However, this situation creates a better climate for mergers and acquisitions, which is another, less risky way to get funding. Likewise, another challenge globally is geopolitical risk; this challenge is likely to drive growth toward stable countries, which was good news for an audience composed mostly of Minnesota and Canadian mining industry personnel. One of the highlights of Kogel?s address was a triangle illustrating the interdependent nature of sustainable development and corporate social responsibility (Fig. 1). This triangle consists of four equal components: the social environment, transparency, local and global impact and future generations. The most important takeaway, Kogel said, was that sustainable development and environmental and social responsibility, while they do add to the cost of doing business, are no longer optional.

Aug 1, 2013

By L. Adler

A fairly complex analysis is required to select, or evaluate a piece of excavating and bulk handling equipment and obtain its performance. At present there is little agreement as to what specific points should be considered, and even less on what procedure to follow. This paper provides both of these in a consistent and direct form. The analysis applies to all types and sizes of equipment from the bulldozer and the continuous miner, to the B.W.E. The importance of the equipment characteristics, job activities, and work conditions are stressed and separate analytical stems are established in a flow chart for these. They are combined using suitability tests in the following steps: 1) problem statement, 2) natural conditions, 3) suitability guidelines, 4) appropriate equipment types, 5) operational activities, 6) encumbered space, 7) geometric design, 8) equipment sizing, 9) failure and limits, 10) performance and consumption, 11) public policy checks, and 12) costs and profitability. Public policy and economics while considered throughout receive emphasis towards the end. The procedure is iterative, containing distinct feedback loops. Specifying the steps and sequence provides a necessary structure which has long been overdue.

Jan 1, 1983