Search Documents

By Keith G. Wallace

The effect of face resistance on ventilation air leakage through stoppings was measured in a twin development heading. Face resistance was varied by alternately tightening or loosening the face line brattice to change the line brattice leakage. Results indicated that tight brattice lines are necessary to maintain acceptable airflow at the face but result in higher leakage throughout the entire system, reduced overall ventilation efficiency, and higher operating costs. Conversely, a low face resistance which simulated an auxiliary fan/duct system gave reduced stopping leakage losses, higher quantities of air at the last open cross-cut and greater entire system efficiencies

Jan 1, 1984

By R. L. Loofbourow

Most wet mines face unquantified water costs as well as the obvious wing costs. Both kinds of cost are multiplied by work at greater depth and by higher unit prices. This intensified challenge merits renewed or perhaps altogether new response. Any practicable way to reduce inflow tackles both obvious and unquantified costs. Ten groups of possible ways to do it are cited. Most have been demonstrated. Two are known from work other than mining. Surely new means can be found. Here are opportunities for operators of wet mines!

Jan 1, 1980

By D. A. Fenton

Two large 34 ½ foot diameter mills have seen seven years of continuous operation before massive fracturing occurred on one of the trunnion cones. These fractures were discovered when liner changes were made. Four modes of failure were identified, three of the modes combining to cause a large circumferential tear in the 4-inch cone plate. A theoretical account is made of the modes of fracture and comparison made with field results. New material was used to repair the fractured cone, and the complete repair took ten weeks. The repair was monitored and lasted twenty-six weeks before the newly designed structure was available.

Jan 1, 1982

By Janet A. Johnson, T. B. Borak, K. J. Schiager

INTRODUCTION In the USA regulatory agencies have adopted standards which limit the allowable concentration of ore dust in underground uranium mines. The American Conference of Governmental Industrial Hygienists has recommended a threshold limit value for silica which has been incorporated by reference in federal regulations (30 CFR 57, 1980). The Nuclear Regulatory Commission (NRC) imposes a limit for unprocessed uranium ore dust for reducing the exposure to radioactive materials from inhalation (10 CFR 20, 1980). We have been unable to trace the origin of the NRC standard. Recently the ICRP has published recommendations concerning limits for intakes of radionuclides by workers (ICRP, 1979). We have used the ICRP methodology to compute the dose equivalent commitment to lung and bone from inhalation of insoluble ore dust particles. These values were used to derive air concentrations which would provide an acceptable risk for induction of cancer from occupational exposure. Results indicate that the new ICRP recommendations are more restrictive than the present NRC standard for radioactivity. The maximum allowable dust load in a uranium mine will depend on both the concentration of silica (% Si02) and the amount of radioactivity (% U308). We have combined these standards assuming complete independence of biological hazard to establish boundary conditions for which either silica or radioactivity is the dominating factor. Based on these results we present suggestions for analysis of ore dust to insure compliance with regulatory agencies. SILICA STANDARDS Silicosis, fibrotic lung disease produced by crystalline silica, was one of the earliest forms of occupational disease to be recognized. The pulmonary lesions caused by silica, silicotic nodules, consist of concentrically arranged bundles of collagen fibers. Fusion of these nodules results in progressive massive fibrosis causing alveolar changes which decrease ventillation and blood flow in the lungs. The current Threshold Limit Value (TLV) for mineral dusts is based on the concentration of free silica. The standard is expressed in three forms: (1) Particle count standard: TLV (mppcf) = 300/(% Si02 + 10) (mppcf = million particles per cubic foot) (2) Respirable dust mass standard: TLV (mg/m3 ) = 10/(% respirable Si02 + 2) (3) Total dust standard: TLV (mg/m3 ) = 30/(% Si02 + 3) The most commonly used form is the respirable mass standard. These curent values for silica are based primarily on epidemilogical studies of Vermont granite workers and other occupationally exposed workers. In the Vermont study no cases of silicosis were seen in individuals employed after dust control measures were initiated and whose subsequent exposure averaged less than 5 mppcf. The free silica concentration in the airborne dust to which these workers were exposed averaged 25%. A concentration of 10 mppcf of granite dust is considered equivalent to 0.1 mg/m3 quartz. The current respirable mass standard allows a maximum silica concentration of 0.1 mg/m3. NIOSH (1974) has recommended a reduction in the current TLV for respirable silica to 0.05 mg/m3 Si02. As with radiation standards, the TLV for mineral dusts is an upper limit for time weighted average exposure. It is recommended that dust concentrations be maintained as far below the TLV as current practices permit. RADIATION STANDARDS The present concentration limit for airborne natural uranium in ore dust prior to chemical separation is 75 µg of uranium per m3 of air ( 10 CFR 20, 1980) . This corresponds to 1.85 Bq/m3 (50 pCi/m3 ) of natural uranium, U-238, U-235 and U-234 and is equivalent to 3.7 Bq/m3 (100 pCi/m3 ) of gross alpha activity with radioactive equilibrium between the long-lived alpha progeny through Ra-226. The origin or basis for this standard is not known, but it presumably includes both chemical toxicity and risk from somatic radiation injury. Recently the International Commission on Radiological Protection (ICRP, 1977) has published recommendations concerning the objectives and criteria for limiting radiation exposures. This was followed b y a revision of the limits for intake of radionuclides by workers (ICRP, 1979; ICRP, 1980). The previous compilation of limits for internal emitters was published by ICRP Committee II in 1959 (ICRP, 1959). The latest version includes new methodlogy outlined in ICRP Publication 26 (ICRP, 1977) as well as extensive metabolic information

Jan 1, 1981

16.1.1-VENTILATION'S ROLE Importance of Ventilation and Environmental Control-Mine ventilation is necessary for the preservation of human life and for the conduct of operations involved in the underground extraction of minerals. It clearly is the most essential of the functions attendant to mining, yet it is auxiliary to the primary objective in mineral extraction. Ventilation in mining thus poses a paradox: ideally, it should be carried out with minimum interference with and cost to production operations, yet it is absolutely vital in providing adequate environmental con¬ditions to support mining. Deterioration of the atmosphere, along with rising ground pressure, imposes the ultimate constraint with depth in underground mining. Ventilation requirements and costs rise rapidly with depth. To preserve atmospheric quality under intense heat conditions, ventilation at great depths must be supplemented by air condition¬ing. Likewise, when mining at any depth under severe or excessive conditions of gas, dust or humidity, supplementary control measures must be employed. In recent years, environmental standards in mines have been raised substantially. While limits are based on human tolerance, increasing concern is being expressed for standards of human comfort. The reasons are economic, as well as humanitarian. Worker performance and longevity correlates closely with environmental quality. Further, adverse accident and insurance compensation rates are a consequence of unsatisfactory environmental conditions. No mining company can afford to be lax in its environmental and ventilation practices. Functions and Processes-Ventilation is the control of air movement, its amount and its direction. As a means of quantity control, it is one of the constituent processes of total air conditioning, the simultaneous control within prescribed limits of the quality, quantity and temperature-humidity of the air. Ventilation is the most common and most. important conditioning process employed in mines for air environmental control. In mine ventilation, air is coursed through the mine workings and openings themselves and, for auxiliary purposes, through vent tubing and ducts. Thus, many interdependencies exist between the mining system and ventilation method. In fact, the two often have evolved ,jointly, as in room-and-pillar extraction of bedded or tabular mineral deposits, such as coal. Ventilation in mines today is provided almost exclusively by large fans, although air flow may result due to natural (thermodynamic) conditions. As mines increase in depth, size and complexity, demands on the ventilation system to maintain more stringent standards of environmental quality likewise rise. On the other hand, never have the technology and resources of the mining industry to cope with environmental problems been so well developed as they are today. In spite of rising costs, it is unlikely that further progress in mine ventila¬tion and air conditioning must await technological breakthroughs. 16.1.2-NATURE OF THE MINE ATMOSPHERE Air Mixtures-Air is a gaseous mixture comprising the natural atmosphere at the surface of the earth. Thermodynamically, it may be thought of as a mech-

Jan 1, 1973

By M Ali, E Satriawan, M Napitupulu, A Munandar

The Deep Mill Level Zone (DMLZ) panel cave mine is one of three active caving mines at PT Freeport Indonesia’s Grasberg Underground Mining Complex. The DMLZ mine is located at a depth of approximately 1,500-1800 m below the surface, making it one of the world’s deepest panel cave mining operations. This depth results in both high in-situ and induced stress that acts on the hard and massive rock mass, triggering rockburst conditions. As a result of the bursting conditions, ground support and maintaining the support capacity are an essential part of operating the DMLZ mine in an efficient and safe manner.

Apr 26, 2022

By Thomas E. Bruner

Today many small diameter tunnels are being constructed in Metropolitan areas and towns as transmission holes for utilities such as water, electricity, natural gas and sewage, to name a few. These tunnels function as utilities beneath the streets, highways, railways, and other structures where open-cut techniques are impractical for any one of a number of reasons. Many such bores range in diameter from 15 to 72 inches and in lengths from 100 to 500 feet. Auger drills with auger type heads have long been used to bore these "road crossings" as they are usually termed; however, many such crossings must be bored in rock with rock-boring heads. Rock with a compressive strength of 15,000 p.s.i. and higher seems to present the greatest challenge for the contractor. These rocks include most igneous and metamorphic rocks and some sedimentary rocks. In general, this grasps most granites, basalts, gneisses, slates, schists, quartzites, limestones, and cherts. In the past ten years boring machines have been developed and used to excavate road crossings through hard rock. Many crossings have been successfully excavated using these machines, and the degree of success has increased substantially in the last few years. A variety of machines have been built and manufactured to bore most rock in a range of diameters up to 72 inches. The machines vary in capabilities, size ranges, and designs but all perform the same basic task and function of boring horizontally. Incidently, here the term horizontal implies horizontal or within five degrees of horizontal. In addition, there is a wide variety of designs, sizes, and types of drill stems, joints, and pipe to meet the various conditions and

Jan 1, 1974

By John K. Adams

Phosphorus may be incorporated into sedimentary rocks in at least four different ways: (1) by the accumulation of detrital mineral fragments, (2) by the accumulation of phosphatic organic debris, (3) by diagenesis and (4) perhaps by the primary precipitation of calcium phosphate. Based-on the petrographic examination of Cretaceous and Tertiary sediments from the northern and central parts of the Atlantic Coastal Plain, Diagenesis is the most important of these mechanisms. Both syndiagenesis and epidiagenesis are required to explain the origin of all the diagenetic phosphate mineral species which occur in the northern and central parts of the coastal plain. Syndiagenesis produced much of the coastal plain's apatite. It was operative below the sediment-water interface while the substrate was being compacted. Compaction forced pore waters, which were enriched in phosphate by the decomposition of organic matter, upward through calcareous sediments. The PO43- radicle replaced the CO23- and calcareous nodules, pellets and shell fragments were converted to apatite. Epidiagenetic reactions occurred in the subaerial environment where downward percolating meteoric waters carried phosphate in solution to cites where cation activity was sufficiently high to form new minerals. Vivianite may form where ferrous iron is available and wavellite and variscite may form in the presence of aluminum rich minerals. Textural evidence suggests that many of the reactions were repeated. The present day appearance of apatite, vivianite, wavellite and variscite in the coastal plain may represent several generations of diagenesis.

Jan 1, 1972

By Richard P. Curtin, Madan M. Singh, Francis S. Kendorski

INTRODUCTION The use of roof and rock bolts to reinforce the strata is an established method of rock support in both underground and surface excavations. However, the need to drill a hole, extract the drill-rods, and then place the bolt is time-consuming and costly. This becomes even more significant if the bolting is repetitive and extensive as in coal mining. Though the main thrust of this development was directed towards coal mining, the basic concepts are also widely applicable to all excavations. The authors, therefore, feel that this innovation should be of interest in rapid excavation and in tunneling. In the case of coal mining, it has been established from past statistics that the roof-bolting operation is the most hazardous activity. This is primarily because of the operator being exposed to unsupported ground. It is evident that remote installation of roof bolts would markedly improve the safety of the operation, if accomplished more readily with self-drilling bolts rather than the conventional two-step variety operation. Thus, in addition to increasing productivity, this development can be considered to be a milestone towards further improvements. The objective of this program was to establish the technical and economic feasibility of self-drilling roof bolts for use in coal mines. It might be clarified at the outset that this work was, therefore, directed primarily at showing that workable self-drilling bolts with less cost can be developed, which could be effectively used in mines. It was not to fabricate a production model bolt.

Jan 1, 1979

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global platetectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20o in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed

Jan 1, 1999

By B. Y. Wong

In April 1989, Southern Company Services signed a 3.5 year contract with DOE-PETC for generic engineering development of an advanced physical fine coal cleaning technology known as selective agglomeration. This technology offers the potential for significantly higher pyritic sulfur removal (90% +) than conventional coal cleaning (30 to 50%) while maintaining high Btu recovery (90% +). Engineering development will include bench-scale process development; component development; adaption or modification of existing unit operations; proof-of-concept (POC) module design, fabrication, testing and evaluation; and small commercial facility conceptual design. The information obtained during POC operation will be sufficient to result in a technical and economic design base that can support construction and operation of a small commercial plant. The major goal of the research is to develop selective agglomeration technology to achieve 90% pyritic sulfur removal while operating at Btu recoveries above 90% based on run-of-mine quality coal. This objective will be accomplished in two phases: Phase 1 -bench-scale and component development, and Phase 2 -POC module operation and conceptual design of a small commercial plant. Currently, work is proceeding under Phase 1 (Tasks 1-7) of the project. A review of the status of Tasks 1-7 is presented in this paper.

Jan 1, 1991

By Kermit Allen

Storing natural gas in solution mined salt cavities appears to be one of the more promising methods being considered by some major gas transmission companies for meeting peak demands. Historically, these companies have been faced with the problem of meeting peak demands when the source of natural gas is located hundreds of miles from the marketing area. Transcontinental Gas Pipe Line Corporation's position was further complicated because some of its offshore Gulf Coast gas supply wells may have to be shut in during hurricane alerts. Transco's solution was to construct. solution mined salt storage caverns adjacent to its pipeline near Eminence, Mississippi. (See Figure 1.) In 1965, Fenix & Scisson, Inc., was engaged by Transco to evaluate the feasibility of storing natural gas in caverns dissolved from salt at selected locations along Transco's pipeline to the East Coast. In June of that year a report was submitted to Transco concluding that this proposal was feasible and recommending several potential sites for storage development. Additional engineering and geological studies followed and in March 1968 the Eminence Salt Dome site was selected and storage construction began that year.

Jan 1, 1971

By D. Tolgyesi, L. P. Gignac

Mine development has evolved in the past 15 years from a human-paced system using hand-held drills and track-bound equipment to a mechanized system using specialized equipment for each component of the development cycle. In most Canadian hard-rock mines, face advance is achieved by the following sequential activities: drilling, explosive loading, mucking and ground support. The state-of-the-art for each work element is reviewed and methods for performance estimates proposed. The entire development system and its production capabilities are considered based on equipment reliabilities, spare units, haulage distances, and muck bay spacing. The effect of the number of working faces on the system's performance will also be analyzed. Manuscript not received in time for publication.

Jan 1, 1983

By R. R. Klimpel

The industrial processing of ores containing precious metals such as gold is generally very mining site specific, e. g. McQuiston and Shoemaker (1985), vanZyl et. a1. (1988), Fuerstenau and Hendrix (1990), and Hausen et. a1. (1990). The variety of various mineral processing techniques employed is extensive and includes size reduction, size classification, gravity separation, roasting, cyanidation, chemical and/or bacterial leaching, ion exchange and/or solvent extraction, and froth flotation. Gold occurs in the earth's crust on the average in very low concentration estimated by various sources to be between two and five parts per billion. For a specific ore deposit to be considered as an economic source of gold, generally a concentration of near one part-per million (one gram / Mton) or more is required. From a mineralogical viewpoint, gold often occurs in its native or free form. However, it can also occur as gold compounds of telluride, antimony, and selenium contained within either sulfide minerals such as pyrite, arsenopyrite. and pyrrhotite or, to a less extent, within silicate, oxide, and carbonate minerals. In many locations, alloying of gold with silver is found. The optimal processing method for recovering gold is determined by many factors such as the mineralogy of the gold bearing minerals as well as the associated mineralogy of the gangue minerals, the type of liberation profile of the gold bearing minerals upon' size reduction, and the particle size of the gold itself. Free or native gold particles can vary in size from the extreme of large nuggets to very finely disseminated gold associated in a complex sulfide mineral matrix. Typically free gold particles of several hundred microns or larger are efficiently recovered by one or more of a number of gravity based techniques due to the large specific gravity differential of gold (19.3 to 15) versus typical gangue minerals (5 to 2.7). When gold is associated with a sulfide (usually pyrite) matrix, historically most industrial plants involving size reduction and subsequent liberation have operated in a size range of 50 to 80 percent less than 75 microns. Grinding finer than this has been normally not economical unless the ore has a high gold content in the feed ore.

Jan 1, 1998

By Allen D. Graham

The coal industry in South Africa is briefly outlined. Test- work carried out on bulk samples of coal in the laboratory and used in the design of the Van Dyks Drift washery are described. Factors affecting the selection of equipment and the designed capacity of the plant are discussed. A description of the crushing plant, washery and load out section is given together with performance data obtained in the final acceptance tests. New features incorporated in the Van Dyks Drift plant and in more recent plants of the Group are outlined.

Jan 1, 1982

By Douglas G. Fox

Outputs from industrial activities planned in the Riley Ridge natural gas project are modeled to determine the potential locations of air pollution impacts on the Bridger and Fitzpatrick Wildernesses in Wyoming. The nature of modeling, especially with regard to its realism, is discussed. Alpine lakes which, along with their watersheds, have minimal buffering capacity are being studied because of their sensitivity to acidic deposition from proposed new air pollution sources. A hypothesis which relates a source's emissions to deposition and lake chemistry in a worst-case sense is presented. Research designed to test the hypothesis and reduce uncertainties is outlined and progress reviewed. Focus is placed on the meteorological transport and atmospheric deposition parameterization contained in the hypothesis.

Jan 1, 1984

By J. B. Zachwieja, P. E. Richardson, G. W. Walker

The electrochemical nature of mineral-collector interactions and their relationship to flotation have been investigated to develop a better understanding of the factors controlling sulfide mineral beneficiation. Spectrophotometric and electrochemical techniques have been used to examine the reactions occurring on electrodes composed of a bed of bornite particles in the presence and absence of potassium ethylxanthate (KEtX) at a pH of 9.2. The combined techniques showed that KEtX sequentially reacts with bornite by (1) a chemisorption reaction forming ca hydrophobic species between --0.4 and -0.2 V (SCE), (2) an electrochemical oxidation reaction forming cuprous xanthate between -- 0.2 V and the xanthate/ dixanthogen redox potential, and (3) oxidation to dixanthogen when the potential exceeds the reversible value for the xanthate/dixanthogen couple. The flotation response of bornite closely parallels spectrophotometric and electrochemical evidence for adsorption of KEtX by the reactions listed above. The degree of surface oxidation resulting from the formation of iron oxides on the surface dictates the flotation response as evidenced by the fact that oxidized bornite floats at more anodic potentials than unoxidized bornite. The strong correlations between the flotation response, degree of oxidation, and potential indicate that chemisorbed xanthate produces a hydrophobic layer sufficient to float unoxidized bornite, but cuprous xanthate and dixanthogen arc required to float oxidized bornite.

Jan 1, 1988

By Werner Wenzel

Whisker growth during the reduction of iron ores The phenomenon of whisker growth can be observed in a number of solid-state crystallisation reactions, which, apparently, appear in6 the first instance as though they are two independent processes. From such reactions, one can find the whisker type of crystallisation on solid bodies. These examples show, that the whisker growth is neither due to certain crystal forms with predetermined temperature and pressureranges, nor to parameters, which, ad hoc, are necessary for the crystallisation. In all cases the whisker formation seems to depend on nucleation and the availability of crystallizing material in direct environment of such a nucleus, under given parameters of a system. One can generally state, that the research of whisker growth with the aim of establishing proper physical laws, to determine the foundamentals of whisker formation and whisker growth, is at present under active study. We can conclude that, although a great number of hypothesis have been proposed; no concluding theory has yet been arrived at. In the institute for ferrous metallurgy of the technical university of Aachen, research works are undertaken to find an explination to various metallurgical phenomena through help of whisker growth which was observed under varying conditions of iron ore reduction. This was possible by using refined microscopic techniques through which the whisker growth on solid oxyde substrates is detected. This refined technique combines the latest methods of surface examination with the help of stereo-scan-electron-microscope and proper and carefull preparation of surface to be stereo-scanned.

Jan 1, 1971

By R. Singhal

Canada's coal production is approximately 65.4 million tonnes of which 95 % is produced by surface mining methods mostly from the three Western provinces (British Columbia, Alberta and Saskatchewan). The mines are highly mechanized; productivity gains during the past few years have ranged from 60 -80%. Truck/Shovel methods are common although Saskatchewan lignite is almost exclusively mined by draglines. This paper provides an overview of Canadian Coal mining industry vis a vis surface mining. Emphasis is on application and utilization of mining equipment and associated mining methods.

Jan 1, 1994

By V. Rajaram

The oil shales located in the Appalachian Basin cover an eight-state area of the eastern U. S., and are referred to as Devonian (black) shales. These shales have been exploited for their gas potential for several years. The Institute of Gas Technology (IGT) has conducted research since 1972 on the production of shale oil from the Devonian shales, and this resulted in the development of the HYTORT process. This process demonstrated that the yield from the Eastern oil shales can be greater than the value indicated by the Fischer assay method. IGT estimates that 423 billion barrels (67.3 x 109 m3) of oil could be recoverd by HYTORT processing of surface-minable eastern U. S. shales. Recently American Syncrude Corporation and Southern Pacific Petroleum N. L. have proposed oil shale projects in Kentucky. This paper will describe the surface mining and retorting techniques that have been studied for exploitation of the Devonian shales, and enumerate the problems that have to be overcome before commercial production can be realized from these shales.

Jan 1, 1983