Search Documents

By Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths (from 500 feet to 1000 feet) and six different diameters (from 14 feet to 24 feet) were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1977

By M. Misra, I. A. H. Schneider

The flocculation of -38 pm calcite, hematite and kaolinite aqueous suspensions by the yeast Candida parapsilosis and products derived from rupture of the microorganism was studied. Flocculation of hematite suspensions by the microorganism and its derivatives readily takes place between pH 2.8 and 11.4. Maximum flocculation occurs at about pH 6.5. Flocculation of calcite suspensions by the microorganism and its derivatives readily takes place between pH 7.0 and 11.8. Maximum flocculation occurs at about pH 10.0. Flocculation of kaolinite suspensions was less than that for the other two minerals. However, a soluble fraction derived from the rupture of the organism functioned as a good flocculant for the mineral, albeit at an increased concentration, between pH 2.6 and 11.5. Maximum flocculation occurs between pH 6.8 and 7.2. An attempt is made to relate the behavior of the various systems to the surface characteristics of the minerals and the surface and chemical properties of microorganism and its derivatives. Experimentation used to evaluate the flocculation includes actual flocculation tests, microelectrophoresis measurements and scanning electron microscopy.

Jan 1, 1994

By Howard S. Avery

The wear resistance of an alloy in heavy mill liner sections may be quite different from that of the same alloy in small balls and other light sections. This fact was established by means of a well standardized laboratory test that was validated for ball mill service. The salient properties of mill liner alloys, including austenitic manganese steels, medium alloy hardenable steels, and abrasion resistance cast irons are described, critically compared, and quantitatively ranked in terms of mill liner service. Where they are tough enough the high-chromium and other martensitic cast irons (e.g. Ni-Hard) promise maximum economy, but their section sensitivity is a limitation. To overcome this an extensive research program studied over a hundred experimental alloys, ranking them for heavy section abrasion resistance by means of the laboratory test. Computer analysis of the results provided a parabolic formula in terms of composition, the apexes of the parabolas providing optimum wear resistance. From the extensive family of parabolas one apex was selected for intensive study in experimental liners, pilot plant production, development of quality controls, and finally full scale production. This is a 19% chromium iron critically alloyed with nickel and molybdenum and hardened by heat treatment. It has excellent resistance to various types of abrasion, but its chief advantage is in heavy mill liner sections, where it has about 25% better abrasion resistance than the best of the quality controlled chilled Ni-Hards. It is also tougher. After production problems were solved, a number of ball and rod mill tests were arranged on a guaranteed performance basis. Two of these, representing about 138,000 pounds of mill liner castings, have recently confirmed in service the superiority that was predicted by the laboratory tests.

Jan 1, 1969

By R. L. Grayson

Using powerful database management software, nested-field analysis and microanalysis of narratives have been made of West Virginia accident data, resulting in a new approach for targeting and prioritizing safety interventions by county, mine size, specific mine, job title, type injury, etc. and combinations of these parameters. The analyses have been useful in focusing training and discussion sessions on specific work problems, trends, conditions, and situations for targeted groups of miners. Application of the technique will be presented in this paper, along with comparisons of various mine performance measures.

Jan 1, 1997

By Hans Treichl

1. INTRODUCTION For Europe the Arlberg road tunnel signifies the elimination of the largest traffic barrier between Bucharest and Paris in the east-west transversal. Apart from that the tunnel will serve the feeder system to the two north-south links Ulm - Milano, and the Brenner motorway, and links the Inntal and the Rheintal motorways closer together.. Thus, the supraregional road system carrying traffic through the Tyrol and Vorarlberg will considerably be emproved by the Arlberg road tunnel. 2. THE PROJECT The 16.1 km contract section of expressway S 16 includes a ramp section of approximately 2.6 km, the access points at St.Anton and at Langen, and the main 13.98 km section of the road tunnel. This section cuts the link between St.Anton and Langen by 3.7 km, and saves 475 m in altitude. The Arlberg road tunnel is planned to have two tubes with two lanes each. In the first stage the southern tube was under construction. Its traffic capacity is 1,800 car units per hour. The tunnel has a cross section of 9o to 103 m2. The sloping gradients are by 1.3o and 1.67 per cent. Fresh air is supplied and used air removed through a ventilation system, fed at the portals and through two vertical ventilation shafts. One of them, at Maienwasen, is 222 m deep, its cross section 66.5 m2. The diameter in clear is 8.32 m. The vertical shaft Albona is 736 m deep, the diameter in clear is 7.37 m. The tunnels is 9,4o m wide, providing for a 7.5o m roadway plus o.95 m sidewalks on each side of it. 4.7o m above the traffic area the conduits for fresh and used air. A transverse ventilation system with reduced exhaust air has

Jan 1, 1979

By R. Gradnik

The continuous need for infrastructure expansion forces the mining industry to develop underground structures into more sensitive and violent environments. When underground excavation enters into deep and high stress rock conditions, geotechnical designers find themselves faced with the difficult task of selecting a rock support system that will meet today's stringent requirements. Whatever support system is chosen, it is mandatory that potential rock movement be controlled. All this has intensified the development of safety systems and new, unique solutions which can enable construction companies to go both, further and deeper, without reducing the level of safety. To address these needs, Atlas Copco developed the Roofex® bolt, specifically designed to withstand large static and dynamic deformations under prespecified load conditions. The Roofex Rock Bolt acts as stiff support up to a designable load level before the sliding effect of the mechanical frictional system is triggered and allows highly controlled rock mass movement without loosing the support function.

Jan 1, 2011

By Shenghui Chu, Zhibiao Guo, Dongshan Yang, Yuanxin Zhao, Xiaohui Kuai, Jingwei Gao

The technology of automatically formed roadway without pillars (AFRP) via roof cutting and pressure releasing (RCPR) is a reformatory method for gob-side entry retaining, which automatically creates a roadway by utilizing the fragmenting and expanding properties of rock strata and the mining pressure, to realize a novel technique for coal mining without coal pillars. The Anju Coal Mine is the first kilometer-deep mine where this technology is applied. To conduct a geomechanical model experiment, this research uses the 5307 working face in this mine as its backdrop. The experimental results show that this technology can efficiently decrease the pressure of the AFRP surrounding rock. The roof maximum stress of the AFRP is 21% lower than that of the belt roadway, while the side abutment pressure of the former is 13.4% lower than that of the latter. The comparison of model experiment data and field monitoring data shows that the roof and floor approaching deformations on the roof-cutting side and solid coal side of AFRP differ by 8.8% and 9.6%, respectively. The model experiment results and field monitoring data show good agreement, and the deformation of the AFRP surrounding rock can be successfully managed by this technique. The study’s findings can serve as a guide for using this technology in kilometer-deep coal mines.

Jul 31, 2023

By George O. Lower

The use of cyanides in the extraction of gold and silver is well known.1 Such extractions employ con¬centrations of cyanide in the range of 0.02-0.25 % sodium cyanide equivalent in leaching cycles of 24-48 hours and frequently longer. Copper minerals, even though minor components of precious metal ores, dissolve in these cyanide leaching solutions, consume cyanide, cause fouling of mill solutions, and thus interfere with the precipitation and recovery of gold and silver. 2,3,4 This paper presents a summary of laboratory investigations on the use of cyanide solutions as extractants for copper from various copper-bearing ore fractions. In view of the metal contents involved, it will be apparent that larger quantities of cyanide are required to extract copper than for the extraction of precious metals. In cyanide solutions of concentrations generally favorable to copper extraction, sulfide and oxide copper minerals were found to dissolve rapidly at room temperature and atmospheric pressure. For example, on products in the flotation size range, the major portions (e.g. 65-85%) of the extractable copper frequently dissolved in 2-10 minutes. At coarser grinds, e.g. 100% minus 28 mesh and 100% minus 10 mesh, 75-85% of the total copper was extracted in 30 minutes.

Jan 1, 1966

By V

"Recent regulations, as well as a general aversion to central dust collectors within the Powder River Basin Coal user’s community, have created a need for an alternate method for eliminating airborne dust. This paper addresses the capital expenditure as well as the cost of ownership of an integrated point source air cleaning system in comparison to a central collection system. This assessment was conducted by comparing the cost to purchase and operate a central dust collection system and integrated air cleaner system on a typical multiple transfer point application. The central dust collector consists of a negative pressure blower, a series of filter bags, a collection hopper, a screw conveyor to place collected material back into the material stream, and a series of ducts to pull air and dust from individual pickup points. The point specific integrated air cleaners consists of a negative pressure blower to pull dust and air from an application point through a bag-less filter media located at the application point. The agglomerated material is then redeposited into the material stream at point of use without the need for ducting or a central material hopper. The assessment yielded a 54% reduction in capital expenditure and a 26% reduction in operating costs for the same application when using individual dust filters as opposed to a central system. In addition to the lowered cost, there are reductions in risk associated with the elimination of ductwork and the central containment enclosure for collected explosive dust. By the conclusion of this paper, the reader will have a better understanding of the quantifiable differences between a central dust collection system and a set integrated air cleaner systems. BACKGROUND Spillage has always been a problem in the bulk solids handling industry. As long as there have been conveyors, there has been spillage. Spillage is material that falls off a conveyor belt and creates a hazard in the environment around a conveyor belt."

Jan 1, 2016

By L. A. Baker

The presence of goethite in a hematite ore has been shown to strongly affect the time of heating to the firing temperature. The investigation of spalling of single pellets and of packed beds has enabled free water and goethite spalling to be identified as separate phenomena. In addition, it has been shown that even for an 18 inch deep bed of green balls the free water and goethite drying periods can be considered separately. Based on this observation, a method of predicting production rate and hood temperature profile is presented. The method required knowledge of the ore goethite content, ore grind and the green pellet bulk density. Laboratory results were found to be in good agreement with actual plant practice and have led to improved process performance.

Jan 1, 1972

By Ralf Plinninger, Pafos Busch, Richard Gradnik

This paper presents the details of the Bad Bergzabern tunnel project. This tunnel is the main part of the B427 federal road bypass, intended to improve the regional traffic infrastructure and to reduce the traffic load in the historic city centre of the health resort Bad Bergzabern. Located in the south-western part of Germany, the project area is situated at the eastern margin of the so-called Palatinate Forest, a low mountain region of mainly triassic sediments with a complex and variable geological history. The German federal government, represented by the office of mobility of Rhineland- Palatinate, awarded the contract to BeMo Tunnelling, a specialized Tunnelling company with a long history of innovation and success in NATM tunnelling. The contract includes the construction of two separate tubes with a length of approximately 1,44 km (0.9 mi)—the road (main) tunnel with a cross section of 101 m2 (1,090 sq ft) and a parallel rescue tunnel with a cross section of ca. 23 m2 (250 sq ft.) Both are connected by six cross passages. Tunnels and cross passages are excavated according to the principles of the New Austrian Tunnelling Method (NATM). Due to BeMo Tunnelling’s technical expertise and capabilities, the project team was able to engineer a speed-up concept that saves money and time for the construction team and client. This paper presents the innovative approach BeMo Tunnelling made to optimize the execution of the tunnelling works and the challenges the project team is facing with regard to a complicated geological situation, countermeasures against an increasing effect of climate change and volatile prices for construction materials.

Jun 13, 2023

By Y. Ye

Typically, rougher molybdenite flotation and recovery from bulk copper/ molybdenum concentrates involves the use of alkalisulfides, Nokes reagents, cyanides, oxidants, and/or thermal treatment for the depression of copper sulfide minerals. The bulk copper/molybdenum feed generally varies from 0.2% Mo to 1.0% Mo, and with traditional reagents the single-stage rougher flotation recovery of molybdenite varies between 40 and 90% at a concentrate grade of 5 to 10% Mo. With ozone conditioning for copper depression, however, improved separations appear to be possible, as demonstrated by tests with Cu/Me concentrates from both the Phelps Dodge Morenci Operations and the Kennecott Copperton Operations. Single-stage rougher flotation after ozone conditioning can provide a molybdenum concentrate at a recovery of more than 90% and a rougher concentrate grade higher than 20% Mo in some cases. Subsequent cleaner flotation with additional ozone conditioning results in relatively copper-free molybdenum concentrates containing as much as 52% Mo. Preliminary analysis indicates that, with a multistage ozone conditioning/flotation strategy, the process is technically and economically viable and should be suitable for industrial application.

Jan 1, 1990

By VIVEK KASHYAP, Evody Tshijik Karumb, PATRICK TAYLOR

The partial reduction of zinc ferrite to zinc oxide and iron (II, III) oxide can enhance the leaching rate of zinc. Zinc ferrite has often been found as a major component of zinc residues and electric arc furnace dust. The Waelz process is an existing process for zinc ferrite processing, which requires a temperature of more than about 1200 °C to produce Waelz oxide containing ZnO. Since zinc residues have been deemed as a potential way for the extraction of zinc and other critical metals, it is important to analyze the reaction kinetics in the temperature range of interest. This manuscript discusses the chemical kinetics of zinc ferrite reduction by hydrogen gas. Several researchers studied the reduction of zinc ferrite with CO; however, unlike CO, the use of H2 gas as a reductant allows partial reduction of zinc ferrite even at low-temperature range (400–600 °C). Thermogravimetric analyses (TGA) experiments were performed in the temperature range of 300–700 °C with 10% and 30% H2, and the data obtained was analyzed using the isoconversional method of kinetic analyses. The standard models used for isoconversional kinetic analysis were chosen from literature and experimental data were fitted to determine the controlling mechanism and calculation of kinetic parameters of reduction of zinc ferrite. The rate of reaction was found to be increasing with an increase in temperature and partial pressure of H2 gas. The reaction could be divided into three stages, where reaction interface contraction was found to be the controlling mechanism at the initial stage of reaction. As the reaction proceeds, product layer thickness increases, and thus, diffusion was found to be the controlling mechanism. Roasting products obtained from TGA experiments were also characterized using a scanning electron microscope (SEM) to verify critical morphological details.

Jul 26, 2022

By Tassos Grammatikopoulos, Mike Johnson, Niels Verbaan

Seabed polymetallic nodules, which contain significant quantities of metals key to electrification such as nickel (Ni), cobalt (Co), copper (Cu) and manganese (Mn) can be processed using several different metallurgical processing options, including direct smelting and subsequent hydrometallurgical refining of the copper/nickel matte; ammoniacal leaching (gas reduction or Cuprion); and acid leaching (often reductive). Many of these approaches suffer from reduced cobalt extraction, difficult physical performance, or overall circuit complexity in general, leading to increased risk to the overall project. SGS has considered the pressure acid leaching of nodules for further investigation, as publicly shared data on this processing route stem from the 1970s and 1980s, and are not always easily accessible. This article details the series of tests conducted and provides updated results obtained — high Ni/Co/Cu recovery with limited manganese/iron (Mn/Fe) — as well as comments on the potential treatment options on the product solution and residue.

Sep 1, 2025

By D. E. Nash

Environmental compliance programs for mining companies are not only important management tools, but can deflect serious civil and criminal penalties if violations of environmental laws do occur. The paper discusses the legal foundation for such programs and their basic structure.

Jan 1, 2001

By Raymond L. Lowrie

Deregulation, as authorized by the Energy Policy Act of 1992 (PL102-486) allows free-market competition in the electric-utility industry. As the act unfolds, though, uncertainties abound about the type, degree and direction of impacts throughout the affected economy — from fuel suppliers to electricity generators and from power distributors to energy consumers. Instead of having a familiar base of captive customers and electricity prices fixed by negotiation with state public utility commissions, utility companies are preparing for open, free-market competition. They are looking at all areas, including fuel supply, to cut costs to remain competitive. Humorous anecdotes are told about utility companies shunning insiders for senior executive positions. Instead, they are opting for people from the telephone or other industries with deregulation experience. And there are light-hearted stories about a trend away from traditional electric-company names, such as the name of a city or state followed by Edison or Power and Light, to space-age names, such as Ameren, Entergy, Illinova or Unicom. No one wants to be left behind or be perceived to be left behind.

Jan 1, 1996

By N. F. Sather

Results of comprehensive trace element analyses of samples of Illinois #5 and #6 seam coals and the unquenched ashes obtained from gasification of these coals in a Lurgi reactor are reported and discussed. Areas where additional background information is needed for assessment of the environmental impact of trace element emissions from coal gasification are identified.

Jan 1, 1976

By Rong Lu, Hao Wu, Bing Dai, Guoyan Zhao, Li Cheng, Weizhang Liang

Affected by the disturbance of blasting activities, deformation instability and rock dynamic disasters are prone to occur in deep hard rock roadways. Thus, it is particularly necessary to understand the failure behavior of rocks and roadways under dynamic loads. In this study, a series of impact loading tests were carried out on sandstone samples with and without a circular cavity by a modified split Hopkinson pressure bar (SHPB) test system. The mechanical properties and energy evolution of the samples were systematically investigated, and the effect of cavity size was analyzed. The results showed that the presence of the cavity in the samples weakens the dynamic compressive strength by more than 10%, and the peak strain and brittleness are also reduced to varying degrees. Under dynamic loading, spalling cracks occur first on the roof and floor of the cavity, and then different numbers of shear cracks are formed on the sample diagonals. The eventual shear failure mode is the result of the connection of the shear cracks and the cavity. As the cavity radius increases, the dissipated energy density and fractal dimension both grow accordingly, leading to smaller and smaller rock fragments. The dynamic failure behavior of the circular cavity can be well explained based on the dynamic stress distribution law. Overall, this study can provide a reference for the study of the mechanism of rock burst in deep roadways.

Feb 18, 2021

By Emily Wortman-Wunder

As the 2013 president of the Society for Mining, Metallurgy and Exploration, Inc., I am pleased to present the 2013 issue of the Transactions of the Society for Mining, Metallurgy and Exploration, Vol. 334. The timely publication of professional papers that promote the advancement of scientific and technical knowledge is critical for enabling technology transfer. SME plays a key role in this process through its publications. Communication within the mining community is the key to a successful profession and society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of AIME; those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2013 Transactions contains 73 papers covering most every aspect of the mining life cycle and encompassing the diverse sectors of our industry including coal, industrial minerals, metals, health and safety and computational methods. It includes all 18 papers published in 2013 in the Technical Papers Section of Mining Engineering magazine (Vol. 65) and all 33 papers published in 2013 in Minerals & Metallurgical Processing (Vol. 30). Additionally, this volume contains 22 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. Some of the many research highlights from 2013 include discussions of perennial issues, such as how to adequately prepare the next generation of mining engineering students for the workforce (Frimpong et al., pp. 44-52) and how to predict and prevent coal mine bursts and bumps (Pariseau, pp. 60-68), the highly anticipated February Rare Earths issue of Minerals & Metallurgical Processing, and papers analyzing electrical injuries in the U.S. Mining industry (Homce and Cawley, p. 367-375) the latest in assessing the safety and efficiency of operations. All 73 technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2013 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2013

By J. R. Heberger

"The Safety Pays in Mining web application, developed by the National Institute for Occupational Safety and Health (NIOSH) Mining Program, helps mines determine the potential costs associated with mining injuries. This web app groups injuries by type, either by the cause of the injury or by the nature of the injury. When the user selects one of over 30 common types of mining injuries, the app provides information on the distribution of costs of workers’ compensation claims for that type of injury. Based on other user inputs, Safety Pays in Mining will estimate the total costs of the selected injuries, including an estimate of additional indirect costs, the estimated impact of total injury costs on mining company profits, and provide some examples of other items (services, equipment) on which companies could spend the savings that result from the prevention of injuries. This paper reviews the Safety Pays in Mining web application by discussing the development of the app, how it is used to show the true costs of mining injuries, and how mines can benefit from using this app. INTRODUCTION Injuries on the job cause pain and suffering. They can also profoundly affect profits and daily operations. In addition to paying direct costs or increased premiums for workers’ compensation insurance, a company might need to pay overtime for other workers to fill an injured worker’s job role, cover training costs for a replacement worker, or divert administrative resources in the wake of an injury. Safety Pays in Mining is a web app that estimates the distribution of these injury costs and assesses the impact that occupational injuries have on a company’s profits. The costs of specific types of occupational injuries in mining are not readily available as mining and insurance companies don’t usually share this information. As a consequence, companies only have cost information based on previous experience with their own employees. Therefore, if a mine never experienced a finger amputation for one of its miners, it would not be aware of the possible costs associated with this type of injury. In addition, injury costs are unique in that the cost distribution is so wide — with half of the injuries in our dataset having mean costs higher than 90th percentile costs — just using the average cost of a specific injury type does not provide adequate information. Some injuries involve immensely high costs, and even though the risk of these high-cost injuries occurring is low, mines need to be aware of their potential impact on their company’s financial health."

Jan 1, 2018