Search Documents

By Menglong Bian, Xiaotong Dong

Thermal damage is an urgent problem faced by deep mining. High-temperature rock mass, hot water and electromechanical equipment are the sources of the thermal damage. The increase in air temperature in mine tunnel is the result of fluid–solid coupling heat transfer from various heat sources. This paper takes a roadway with hot water and a mine car as the research object. Based on the Fluent, Static Structural and Steady-State Thermal modules in ANSYS, the thermal-fluid–structure coupling analysis in the roadway is carried out. It is found that the hot water has a significant effect on the thermal environment of the mine. Under the experimental parameters, the maximum heat flux density and equivalent elastic strain at the interface between the hot water and the rock are 9789.3 W/m2 and 0.00054532 m/m, respectively. The heat flux distribution in the rock area near the mine car does not change much, and the equivalent elastic strain value in this area is high. After the air is heated in the hot water area, the temperature curve changes gradually and then rises steadily. By changing the inlet air temperature parameter, it is found that the lower the inlet air temperature, the better the cooling effect, and the change of the inlet air temperature can change the air temperature field in the roadway as a whole. By changing the parameter of inlet air speed, it is found that higher wind speed brings better cooling effect, but with the increase in wind speed, the cooling effect of roadway thermal environment is very limited. When the wind speed increases from 5 m/s to 10 m/s, the air temperature of most measuring points drops by more than 2℃; when the wind speed increases from 15 m/s to 20 m/s, the air temperature of most measuring points drops below 0.7℃. After the wind speed reaches a certain value, the cooling effect of ventilation is very limited.

May 5, 2022

By Richard A. Thomas, III JAMES H. ROWLAND, Liming Yuan

This paper presents the results of large-scale fire experiments on evaluating the performances of carbon monoxide (CO) and smoke sensors at low ventilation velocities. Experiments using three different combustibles — conveyor belt, coal and diesel fuel — were conducted in the experimental mine at the U.S. National Institute for Occupational Safety and Health (NIOSH) Bruceton Research Facility. A total of eight sensor stations were located downstream of the fire with each station containing sensors for CO, smoke, carbon dioxide (CO2 ), oxygen (O2 ), humidity, barometric pressure and temperature, as well as two airflow sensors. The airflow velocity ranged from 0.22 to 0.26 m/s (44 to 51 fpm) in the tests. The response times were recorded for the CO and smoke sensors at each sensor station when smoke and gaseous products of combustion from each burning combustible reached the station. The response times of the CO sensors were used to determine the appropriate sensor spacing in the belt entry with a low air velocity. The performance of the smoke sensor was found to be affected by the high humidity in the experiments. The results on proper selection of sensors and the determination of sensor spacing at a low ventilation velocity can be helpful for ensuring sufficient early fire warning for underground workers, thereby improving the health and safety of miners.

By J. Evans

INTRODUCTION Section 209(b) of the Federal Land Policy And Management Act of 1976 (FLPMA-43 U.S.C. 1719 b) authorizes the Secretary of the Interior to convey mineral interests owned by the United States where the surface is or will be in non-Federal ownership. The objective is to allow consolidation of surface and subsurface (mineral) ownership. Certain major conditions must prevail for a conveyance to occur. These are: 1) There are no known mineral values (KMV) or 2) Where the mineral reservation interferes with or precludes appropriate non-mineral surface development and that non-mineral development is a more beneficial use of the land than the mineral development. Remember that allegation, hypothesis or speculation that the conditions could or may exist in the future will not be a sufficient basis for conveyance. Convincing factual evidence for an applicant’s case for mineral conveyance must be made in order to achieve that conveyance. See 43 CFR 2720 0-1 to 0-3, and 0-6. CONCEPT OF KNOWN MINERAL VALUES Known mineral values means mineral rights in lands containing geologic formations that are valuable in the monetary sense for exploring, developing, or producing natural mineral deposits. The presence of such mineral deposits with potential for mineral development may be known because of previous exploration, or may be inferred based on geologic information (43-CFR 2720.0-5(b).

Jan 1, 2007

By Alden B. Carpenter

Oil-field brines have been collected and analyzed from Jurassic and Cretaceous rocks in the Mississippi Salt Dome Basin, from Jurassic and Lower Cretaceous rocks, southwestern Arkansas, and from Ordovician and Silurian rocks, southern Michigan. All of these brines are genetically related to evaporites and appear to be brines expelled from halite-bearing rocks, presumably during compaction. The brines in rocks closest to the halite-bearing rocks are uniformly low in lead and zinc suggesting that the metals in metal-rich brines are not acquired within evaporite sequences. The metals in metal- rich brines in Mississippi and in Russia appear to be derived from red beds and may have been originally associated with ferric iron oxyhydroxides. Reduction of these compounds by migrating hydrocarbons appears to release lead and zinc to the associated brines accompanied by the fomation of authigenic ankerite.

Jan 1, 1979

By Fred Heivilin

A symposium on the characterization and toxicology of mineral dusts was held Sept. 19 and20 in Washington, D.C. The symposium was held to update the minerals industry, the health community, government agencies and academia on the technical, health and regulatory aspects of minerals to be evaluated by the International Agency for Research on Cancer (IARC).In October 1996, the IARC met in Lyon, France, to discuss and prepare “Volume 68 of the IARC Mono-graphs on the Evaluation of Carcinogenic Risks to Humans on Silica, Silicates, Dusts and Organic Fibers.”

Jan 1, 1996

By M. Botz

Alacer Gold Corporation is constructing the Çöpler Gold Mine in eastern Turkey. Mining commenced in the fourth quarter of 2009 and gold production started in the fourth quarter of 2010. The mine is a 15,500 t/day oxide heap leach with three-stage crushing, agglomeration, carbon adsorption and electrowinning for final metal recovery. Leach solution copper levels are expected to be relatively low during the first two years of production, but will increase in later years due to higher copper content in the mined and processed ore. Over the mine life, approximately 40 Mt of ore will be placed on the leach pad, which will contain about 35,000 t of copper. Metallurgical testing indicates copper extraction will vary by ore type and, if controls are not implemented, may lead to copper levels exceeding 1,000 mg/L in pregnant solution. High copper levels in leach solution have the deleterious effect of increasing cyanide consumption and potentially overwhelming the ability of the carbon circuit to effectively adsorb the principal economic metals, which in this case are gold and silver. Using data obtained from laboratory leach column testwork, the heap leach facility was modeled using METSIM process simulation software to estimate the build-up of copper in leach solution over the life of the mine. Laboratory testwork was also performed to evaluate process conditions for treating a portion of pregnant leach solution via sulfide addition to precipitate saleable copper as copper sulfide (Cu2S).

Jan 1, 2011

By Arash Habibi, Anna Cable, David Loring, Aleksandar D. Bugarski, Logan Ingalls, Calvin Rutter

The results of diesel particulate matter (DPM) monitoring were used by the underground mining industry to mitigate adverse effects of exposure to DPM. NIOSH Method 5040, currently used for ambient and personal exposure monitoring, does not provide needed real-time information. The objective of this study is to develop a methodology for continuous monitoring of DPM concentrations in an underground environment, founded on the application of the Dekati electrical particle sensor (DePS). The DePS, which measures concentrations of submicron aerosol in real time using a diffusion-charging sensor, was evaluated by comparing the results of the concurrent measurements with reference methods at several locations downstream of the diesel-powered equipment. The DePS results were found to correlate well to those obtained by reference methods. However, it was found that dependence of the response on the physical and chemical properties of aerosols necessitates sitespecific correlation factors for the targeted matrices. The site-specific factors for number and mass of diesel aerosols were derived using the results of concurrent measurements with TSI NanoScan, FLIR Airtec, and carbon analyses performed on the concurrently collected filter samples. The results showed that methodology based on compensated DePS measurements would be suitable for continuous monitoring of DPM in underground mining operations.

Dec 1, 2022

By V. J. McSweeney

This paper is directed at interested parties outside the Beach Sand Industry : the scope is quite broad. The geomorphology described is a successful working hypothesis which guided the author during prospecting and pegging campaigns : the author is not an expert in this field. The test data used in the text, for illustrative purposes, is original and may constitute a contribution to the state of the art. The operation- al and design philosophy embodied in the text is personal and describes the author's methods : all practising exponents would differ in some degree amongst themselves on these subjects. In this paper, no criticism of any existing operation or brand of equipment is intended and names are used to maintain a real contact with the subject matter. The author believes that the operational and design techniques evolved in the Beach Sand Industry under continual duress, have a wider application in the mining industry. This glimpse of the Industry is intended to enhance the respect for the present and past members. Space does not permit individual acknowledgements.

Jan 1, 1982

The use of coal as a fuel causes air, pollution in; a number of different forms, and in nearly all stages of its, handling, preparation, storage, use and-disposal of its residue. First let us consider the handling of coal. As shipped, particularly to large utilities, it is run-of-mine bituminous made up of large chunks as well as pulverized particles. Because it 'is in an open car or barge, it is subject to the action o winds and the small particles may be blown around adding to the-particulate load in the atmosphere. Mien un¬loaded from the barge or car, there is again an opportunity for the wind to blow the fine particles around. All of us I am sure have seen a barge at the dock of a utility plant being unloaded by a clamshell bucket. This, after grabbing its load from the barge, lifts it some 60 or 70 feet and, then drops it on a conveyor, which carries the coal to a storage area.

Jan 1, 1964

By David Hanson, Sean Warren, Chaparral Berry

"Coal bumps, also referred to as dynamic failure events or coal bursts (Lawson, Weakley, and Miller, 2016), continue to be a hazard in underground coal mines. While current design methods have significantly reduced the occurrence of coal bumps, they have not been completely eliminated. This paper investigates a correlation between coal compositional components, coal molecular structure, and probability of coal bumps in an effort to deepen understanding of coal behavior in an effort to reduce hazards in underground coal mines.Samples from the Penn State Office of Coal (PSOC) Department of Energy Coal Samples (DECS) were obtained for Fourier Transform Infrared Spectroscopy (FTIR) analysis using the KBr pellet method. Peaks indicative of the coal molecular structures were obtained using spectral integration software. These data, combined with published elemental data, were compared to historic bump occurrence in order to establish a possible correlation. Finally, results based on multivariate analysis of the elemental and FTIR data with bump status as the dependent variable suggest that elemental sulfur and molecular structure can be used as an indicator of bump susceptibility within the sample set considered.INTRODUCTIONThe study of coal requires consideration of multiple variables: percentages of organic and inorganic components, organic component origins, coal age, pore structure, cleat density, elemental composition, etc. Examining coal in situ increases the number of variables, such as coal depth, seam thickness, surrounding stratigraphy, and so forth. This collection of variables influences the subsequent behavior of coal simultaneously, and weighing their relative impact is a challenge for researchers. “A problem never exists in isolation; it is surrounded by other problems in space and time” (Ackoff, 1956). Having a substance such as coal that we know so much about, and yet so little, we have to ask what can be learned.An experimental study using Fourier Transform Infrared Spectroscopy (FTIR) was undertaken to determine if the chemical structure of coal contains information which may lead to a better understanding of triggers or attributes which may, in turn, lead to an increased probability of a dynamic failure event. While a full analysis of the factors driving dynamic failure are beyond the scope of this study, it is possible that a better understanding of the chemical structure of coal will lead to an increased knowledge of its inherent behavior, including its propensity to burst."

Jan 1, 2019

By K. C. Kocsis

"Diesel-powered equipment has allowed the mining industry to raise production rates and significantly improve productivity, as it is rugged, mobile and reliable, but its widespread use in underground mines has generated concerns regarding the exposure of mine workers to harmful diesel engine exhaust gases and particulate components such as diesel particulate matter (DPM), which has recently been classified as a human carcinogen by the International Agency for Research on Cancer. The agency expressed further concerns that workers’ exposure to high DPM concentrations can increase the risk of cardiovascular, cardiopulmonary and respiratory illnesses. Three emerging technologies could have the ability to replace dieselpowered equipment and remove DPM from underground mines: fuel-cell-powered mining equipment, battery-powered mining equipment and advanced material handling systems. This paper reviews them and assesses whether they have reached the point where the pollutants emitted by diesel-powered equipment can be removed from underground mines through the introduction of zero-emission mining equipment and power systems. Information is also provided from the results of a feasibility study, including a detailed cost benefit analysis, carried out at six Canadian and nine U.S. underground mines, which looked at the possibility of replacing diesel-powered production equipment with fuel-cell-powered equipment. The remarkable pace at which battery technology is progressing is also reviewed, and the feasibility of replacing diesel-powered mining equipment with battery-powered equipment is assessed. IntroductionHazardous pollutants in underground mines. Why is it important to remove diesel particulate matter (DPM) from underground mines? Over the past 40 years, diesel-powered equipment has allowed the mining industry to achieve rising production rates and major improvements in productivity, as the diesel engine is an economical source of power and diesel-powered equipment is usually rugged, mobile and reliable. On the negative side, the toxicity of some diesel exhaust gases is well known (Grenier et al., 2001), and the widespread use of diesel-powered equipment in underground mines has generated increasing concerns about the occupational exposure of mine workers to harmful diesel engine exhaust gases and particulate components such as DPM. Diesel equipment also entails other hazards like heat and humidity. Exposure to excessive heat can cause heat illnesses, such as heat rash, heat exhaustion and heat stroke (Donoghue, 2004; Roghanchi et al., 2016), and a hot and humid underground environment negatively affects the efficiency of the workforce, which may result in a decline in production output (Roghanchi et al., 2017)."

Jan 10, 2017

By Mengxiong Guo, Xuxin Shao

The recent depressant research is summarized, and a new kind of depressant (SCO) has been put forward in this article. Using Na-oleate as a collector and SCO as a depressant, separation of dolomite and phosphate was studied. When SCO was added in the concentration range of 80 g/t to 2kg/t at pH 9.5 ± 0.2, dolomite was absolutely depressed, and apatite kept its floatability. Interestingly, in the mixture of phosphate and dolomite, the dolomite floated. The reasons for such a behavior are investigated through flotation and electrokinetic studies. It was found that the adsorption of dissolved species on dolomite and phosphate resulted in reverse flotation. A concentration of 31.59% P205 and 83.87% recovery of P205 was obtained from the mixture of phosphate and dolomite (2:1) with 26.6% P205 using 210 g/t SCO and Na-oleate 4.93*10-5 M at pH 9.

Jan 1, 1989

By Chengliang Jliang, B. K. Parek, Xuxin Shao

Of the impurities present in phosphate ore, dolomite is the most difficult to remove due to the similar chemical compositions of the impurities and also adsorption of dissolved species of dolomite onto phosphate. A new amphoteric surfactant was found to be a suitable collector for separation of dolomite from phosphate. Flotation results showed that the new amphoteric collector had a high flotation selectivity for dolomite in wide pH ranges. The flotation study of francolite and dolomite in each other's supernatant demonstrated that the dissolved ions had little effect on the selectivity of the new collector, but were detrimental to the flotation separation using sodium oleate as collector. A phosphate concentrate with 35.2% P2O5 with 90% recovery was obtained using 290 g/t of the amphoteric collector from a mixture of francolite and dolomite containing 26.2% P2O5. The rejection of MgO was 81.41%.

Jan 1, 1999

By Steven E. Mischler, Jay F. Colinet

The Mine Safety and Health Administration (MSHA) promulgated a rule in 2014 that required numerous changes in compliance dust sampling requirements for coal mine operators. Two key parts of this rule were the lowering of the respirable coal mine dust standard from 2.0 mg/m3 to 1.5 mg/m3 and requiring operators of underground coal mines to use a continuous personal dust monitor (CPDM) for compliance sampling. The CPDM currently approved for compliance sampling is equipped with a display that provides miners with in-shift information on their respirable dust exposure. The goal was to provide an indication of a potential overexposure and empower the miner and mine operator to implement changes in controls and/or operating practices to prevent an overexposure from occurring.

By Richard P. Stahura

During the next five years, there will be a trend toward performing belt cleaner maintenance while the conveyor is in operation. Most mines and industrial sites that use belt conveyors have an in-house safety rule that the belt must be stopped before maintenance work can be performed on any belt-cleaning device. This is a good rule. Most cleaning devices are positioned against the belt with hardware that requires the service technician to reach or climb into the chute to change the cleaning blades. But this simple rule becomes more complicated as production demands require higher conveyor availability and provide fewer conveyor outages. In many cases, today’s conveyors are expected to be available 98% to100% of the time.

Jan 1, 1996

By A. Noble

Linear circuit analysis (LCA) is a fundamental tool which has been used to evaluate mineral separation circuits during the preliminary design phase. Traditionally, the LCA methodology uses the analytic circuit solution to determine the relative slope of the circuit?s partition curve. This value is then used as an indicative performance measure suitable for the comparison and ranking of alternative circuit configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. In most mineral systems, this material represents a small portion of the initial feed (due to liberation) as well as a small portion of the revenue potential (due to the incremental value). Respecting these limitations, the authors have developed new separation performance indicators which may be derived from the analytical circuit solution and used in LCA problems. These indicators inherently reflect the separation potential of pure material, providing a better indication of lost revenue due to misplaced material. The complete methodology has been integrated with prior software to produce the Heuristic Optimizer for Resource Separation Economics (HORSE).

Feb 23, 2014

By Fouad Faraj

For every blast pattern, zones of unique material types need to be classified before mining. Most material types can be summarized into different kinds of ore and waste. Blocks generated from blasthole assays are too small to be selectively mined, so areas with a single material classification meeting the mine’s selective mining unit must be defined. Current industry standard practices are to manually draw ore/waste dig limits, but this process is subjective and results in quantities of dilution and ore loss that can be improved upon to enhance the profitability of mining operations. In this study, two weeks of production data from a homogeneous copper (Cu) porphyry and heterogeneous manto-type Cu deposit were used to assess the variability in the hand-drawn dig limits of 20 geologists, mining engineers and ore control specialists, which were compared with the optimal ore/waste delineation. The profit for 20 distinct hand-drawn dig limits for the homogeneous mine varied by 3.7 percent, from $10.5 million to $10.9 million, averaging at $10.8 million. The percentage was nearly double for the more heterogeneous mine at 5.9 percent, from $17.9 million to $19.0 million, averaging at $18.6 million. Using the optimal ore waste delineation, the profit increased to $11.0 million (1.9 percent increase) and $19.3 million (7.0 percent increase) for the homogeneous and heterogeneous deposit, respectively. The natural variability, diggability requirement and selectivity are identified as the main drivers of ore loss and dilution. Recommendations are provided for reducing the subjectivity in manual hand-drawn dig limits by integrating dig limit optimization algorithms as a tool to assist practitioners.

Oct 1, 2024

By Jorgen Elbrond

The capacity calculation of complex transportation systems involving variable activity times such as encountered in the mining industry are often worked out by means of simulation, which reconstructs waiting times and cycle times. The queuing theory, which mathematically calculates waiting times, has been used mainly to describe the, phenomena. This is due partly to the difficulties encountered in modelling complex systems and partly to the difficulty of reconciling the required time distribution laws with the real phenomena by means of the queuing theory. It is, however, obvious that formulas for capacity calculations would be preferable to simulation procedures because of their higher calculation speed, shorter and more flexible programs and shorter programming work. The calculation procedure presented in this paper is composed of some rather simple models, which are based on the queuing theory, and on some probabilistic and some deterministic considerations. The models are supported by observations, and to some extent by simulations. It has been attempted to find all the components of the cycle time and to include them in a comprehensive model. It is the intention to demonstrate that even quite complex mine transportation systems can be treated by means of the queuing theory with the advantages mentionned above and, without sacrificing the precision of the estimates. The speed of calculation of a wide range of parameter combinations is such that the procedure can be used extensively by a project engineer in the search for optimal modifications of the entire transportation system.

Jan 1, 1979

By S. P. Fleming

An acid mine drainage sludge containing 0.26% nickel, 0.21 % cobalt and 4.5% manganese was leached in a one-liter reactor with sulfuric acid in the absence and presence of sodium sulfite. The effects of temperature (25°C and 52°C) and sodium sulfite concentration (up to 0.03 molar) on the leaching rate were particularly investigated. The leaching rates of nickel and cobalt with sulfuric acid have been determined to be controlled by diffusion through product layer. It has been found that effective leaching conditions to give more than 90% extraction of nickel, cobalt and manganese while keeping the iron extraction below 10% come with an elevated temperature and a low sodium sulfite concentration at pH 3; for example, 52°C and 0.01 molar sodium sulfite.

Jan 1, 1992

By Andrew J. Petruska, Austin F. Oltmanns

The paper proposes a capacitive load cell for detecting changes in material and tool wear conditions for conical picks used in underground mining. The current process is dangerous and subjective, relying on human operators near the cutting interface. The new sensor aims to improve worker safety by allowing operators to perform their functions from a greater distance.

Aug 1, 2023