Search Documents

By K. A. Lewandowski

Binders have been suggested as an aid for agglomeration to improve copper recovery in heap leaching operations. However, it has not been established if the use of binders would negatively affect the solvent extraction process, which is used to purify the pregnant leach solution from the heaps and remove any contaminants. Such negative effects would lead to an increase in processing costs or a decreased in copper production. The controlled studies reported here have shown that some binders (a polyacrylamide and a waste treatment additive) did not interfere with the solvent extraction process. Other binders (a polyvinyl acetate emulsion and tall oil pitch) negatively impacted copper solvent extraction and, therefore, should not be used in copper heap leaching plants.

Jan 1, 2009

By David E. Nicholas

Design of underground openings is becoming more critical as the mine deposits become lower in grade, initial investments increase, ore depth increases, additional safety regulations come into law, and increased ore recovery is required for conservation of minerals. Stability of these openings is dependent on the strength of the rock mass and the pre-mine stress field. The rock mass is composed of solid blocks of rock (rock sub- stance) and structural features (faults, joints, bedding, etc.). Methods of testing the rock mass strength are improving and be- coming more common, however it is difficult to justify the high cost of large scale testing for an initial mine design. An alternative to testing the rock mass is to measure the rock substance and the structural features separately, and then combine them to estimate the rock mass strength. The rock mass strength will vary depending on the orientation of the opening with respect to the structural features. The other factor affecting the stability of underground open- ings is the pre-mine stress field. Methods are available to measure "directly" the pre-mine stress in competent and relatively massive rock. These methods are costly to employ, therefore, they may not be justified in an initial study. The pre-mine stress field can be estimated based on the structural relationships formed from past tectonic events.

Jan 1, 1976

By Michael Lenz

Predictive maintenance technologies including vibration analysis, tribology, infrared thermography, ultrasonic detection, and electrical measurements have been applied to large electric mining shovels. The predictive program was initiated on the P&H Model 2300 and 4100 electric shovels. The utilization of these technologies has shown the potential for improving electric mining shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition based planning of component replacement. Maintenance costs are minimized by focusing resources through condition based prioritization.

Feb 24, 1997

By James L. Poole

The gold and silver markets from the late 1960's to the present are reviewed and the outlook for these metals in the 1980's is presented. Included in this discussion is a summary of the basic supply and demand balance for gold and silver since the mid-1960's. an explanation of the price formation for the metals, some of the relationships between the prices of these metals and selected economic parameters, and how these factors affect the outlook.

Jan 1, 1981

By J. Drew

Oregon Resources Corporation (ORC), an industrial minerals mining company, is currently engaged in the development of a new process design that will allow the unique paleo-beach placer deposits of southwestern Oregon to be mined efficiently and economically, creating an additional domestic source for chromite, garnet, and zircon. Engineering design has been guided by the variable geology and mineralogy of the paleo-beach placer deposits as well as the need for a dry tailing scheme that resolves a lack of water resources at the placer locations and at the same time eliminates the need for slurry settling ponds, typical of paleo-beach placer operations in North America. Metallurgical study of the placer material was grouped into four distinct samples based on marine terrace deposition, geological facies, and mineralogy. Because the metallurgical samples represented the extremes likely to be encountered in all future Oregon paleo-beach placer ores, the process design is highly dynamic and will successfully adjust to meet the production needs. Water availability at the mining area is seasonal and will not support a typical placer operation?s water requirement needs for heavy mineral concentration. For this reason, ORC has developed a plan to construct the ore processing facilities near Coos Bay, where a municipal source of water is available. Raw ore will be transported from the mining sites approximately twenty miles one way to the processing facility with return loads hauling tailings back to the active pit. The need to haul dry tailings, return dry material to the pit for reclamation, and limit the amount of water being purchased from the municipality has driven the design of a unique water reclamation system. BACKGROUND Location and Access Economic concentrations of ?black sand? or heavy mineral (minerals with specific gravity greater than 2.85) have been recognized and studied in marine placers from Coos Bay to the mouth of the Rogue River, a distance of approximately 75 miles along the southern Oregon coast (Hornor, 1918; Griggs, 1945)(Figure 1). ORC will begin mining existing reserves approximately 20 miles south of Coos Bay in a region known locally as Seven Devils. Ore will be trucked north to the processing site near Coos Bay via use of existing county and state roads, including U.S. 101. The available facilities at the processing site include highway, rail, municipal water and electricity, natural gas, and a deep water port. At the time of this writing, the rail line had been abandoned, but was being pursued by the International Port of Coos Bay. It is anticipated that this will be serviceable at some time in the future. History The southern Oregon marine placers have garnered the interests of miners since 1852, when present day beaches were exploited for gold. The beach deposits were small and irregular in nature and were easily washed away by the major storms the coast endures during the winter months (Hornor, 1918). [ ] In the 1920?s, deposits at the beach were followed upstream to their paleo-beach terrace origins (Pardee, 1934). These terrace placers were mined, but with little success, as the cost of mining and processing was greater than at the present day beach deposits. The greatest effort to understand and delineate the paleo-beach terrace placers came during World War II. As the need for a domestic source of steel hardening chromite was evident, the heavy mineral bearing placers of southwestern Oregon provided just that. The U.S. Geological Survey, under guidance from the Oregon Department of Geology and Mineral Industries, began exploration drilling of the paleo-beach terraces in 1940 (Griggs, 1945). This work was part of the investigation of strategic mineral deposits and would ultimately supply much needed chromite for the war efforts. The first mining efforts began in 1943 by the Humphreys Gold Corporation and the Krome Corporation (Griggs, 1945). Black sand

Jan 1, 2009

By M. D. Johnson

Mina Santa Rosa, in west central Panama, is the first large-scale gold mine in Panama and will soon be the largest single-mine gold producer in central America (Fig. 1). At full production, the mine will process 1.8 Mt/a (2 million stpy) of ore and produce more than 1.8 t/a (60,000 oz/year) of gold and 9.3 t/a(300,000 oz/year) of silver. Mina Santa Rosa is a subsidiary of Greenstone Resources of Toronto, Ontario. Freeport-McMoRan geologists first visited the area in 1985. Their rock chip sampling adjacent to old shafts and adits confirmed widespread gold and trace element geochemistry anomalies. Surface mineralization appeared to be localized in and adjacent to narrow veinlets. However, they recognized astructural setting similar to the Nevada Tertiary volcanic-hosted epithermal gold systems.

Jan 1, 1996

Introduction Aggregate mining impacts on water resources are a source of concern to local governments. To evaluate those impacts, the Minnesota Department of Natural Resources conducted a four-year study at three gravel pits (two alluvial and one beach-ridge) and five quarries (flat-lying Paleozoic limestone). This research provides the first comprehensive look at aggregate mining impacts on ground-water systems in Minnesota. The results will be used by government officials making permitting decisions about aggregate operations and by responsible owners of aggregate mines as they plan their operations to avoid conflicts with neighbors and with resources dependent on ground water and surface water. Natural aggregate (crushed stone, sand, and gravel) is a vital part of our economic infrastructure in Minnesota. Aggregate is used for road and bridge construction and in a variety of building materials. In 2003, the value of construction sand and gravel and crushed stone in Minnesota was approximately $245,000,000. As Minnesota’s economy continues to expand, the demand for aggregate will continue to grow. Sand and gravel pits are located in every county in Minnesota. In 1990, the Minnesota Department of Natural Resources, Division of Minerals (DNR Minerals), estimated the number of active and inactive operations at 1500 with the view that this number was likely too low. Quarries for mining limestone, dolomite, sandstone, and hard rock (granite and quartzite) are found in 34 counties. A 1990 DNR Minerals inventory found 165 active operations, 88 percent of which were limestone quarries (Nelson and others, 1990). That same inventory counted 1,367 inactive operations, 70 percent of which were limestone quarries. Aggregate mining is an extractive use of resources: mining alters the landscape and its natural hydrologic system. When a new pit or quarry is proposed or when an existing operation needs to expand, local governments and citizens typically have many questions about the impacts mining might have. Local governments, which are responsible for reviewing these operations, rarely have the budgets to hire experts to evaluate potential impacts of quarry and gravel pit proposals. The Minnesota Legislature’s Aggregate Resources Task Force identified that local government units (LGUs) often lack the expertise to assess ground-water models (Southwick and others, 2000).

Jan 1, 2007

By B. J. Arnold, N. Terblanche

The features of the ‘Turbo’ froth flotation column will be discussed, including the double aeration system that improves flotation yield while not sacrificing grade, the internal launder system, and the unique feed/tailings sump that evens out flow to the flotation column preventing upset conditions. Results from various test programs and installations will be presented.

Jan 1, 2001

By B. R. Zernich

Advances in tunneling technology, such as Earth Pressure Balance and Slurry Shield methods, have allowed the tunneling industry to construct tunnels in increasingly difficult ground conditions. In recent years, a number of civil projects including large diameter train tunnels, subway tunnels, water tunnels, sewer tunnels, and combined sewer tunnels have been successfully completed deep beneath the water table in soft ground conditions utilizing modern day Tunnel Boring Machines (TBM). With the increase in difficult ground conditions and higher water pressure comes the inherent need to utilize compressed air to gain access to the TBM?s cutterhead and cutting tools. This paper focuses on one such instance in Los Angeles, CA in which Traylor Brothers Inc. performed a cutterhead intervention by compressing the heading of an 11-foot diameter tunnel to approximately 3 bar gauge pressure. This paper focuses on the environmental controls used to manage ventilation, oxygen levels, temperature, and pressure, as well as discusses the problems associated with toxic gases and the increased risk of fire. The paper will also cover the physical science of the environment and the increased risks of performing basic job functions while in a compressed air heading.

Jan 1, 2009

St. Peter sandstone is very different from the minerals and rocks that have been studied extensively in mining. On the one hand, it is brittle as characterized by an unusually high friction angle and steeply curved failure envelopes. On the other hand, it is friable, possessing extremely low, and in most cases zero cohesion. The scarcity of the ground control techniques for this particular mining environment has created many difficulties for the mine operators. In order to resolve these problems, the geotechnical properties of the St. Peter sandstones were investigated through a comprehensive research program, which included uniaxial test, triaxial test, porosity test, thin section, X-ray diffraction (XRD), and scanning electron microscope (SEM). The specimens used for the uniaxial and triaxial tests were specially prepared because of the highly friable nature of the St. Peter sandstone. Thin section, XRD and SEM were utilized to examine the effect of the microstructure of the St. Peter sandstones on its strength characteristics.

Feb 27, 2013

By Ray Brainard

The subsurface investigation for the Reach 4 Tunnel was expected to be completed in a single phase. This assumed that data from two nearby previous tunnels, combined with limited new subsurface information and surface mapping would be sufficient to characterize the rock behavior. Unforeseen rock conditions and complex faulting led to the recommendation for a second phase. This decision was not reached easily, as much of the follow-on work required helicopter support, and associated costs. The second phase of drilling found significantly more variability than the first phase and led to a very different and better understanding of the geologic and geotechnical conditions, and rock characterization.

By L. W. Berry

Drill and blast planning is critical to successful mine production, both in timing and in results. However, typical planning, reporting, and information exchange usually involves large quantities of data collated in a discordant set of spreadsheets, databases, and reports. Collecting, analyzing, modeling, and distributing all data necessary for efficient drill and blast operations is time consuming and cumbersome. MineSight Axis Drill and Blast provides an extensible core of functions, seamlessly integrated with other MineSight software tools, to make sense of this information. The benefits of improving the management of drilling and blasting processes are immense and result in improved fragmentation at a lower cost, improved shovel and truck productivity, and enhanced ore processing.

Jan 1, 2011

By AMAN SONI, JONATHAN G. BAGGETT, Nino Ripepi, JUAN J. MONSALVE, Richard Bishop

Underground stone mines are vulnerable to karst void formations due to the erosion of carbonate rocks by groundwater flow. The voids or cavities may lead to hazards including ground collapse and sudden outflow of clay-rock sediments during the development of the mine. This study evaluates the effect of karst voids on the strength of pillars in an underground room-and-pillar limestone mine. Ground-penetrating radar (GPR) surveys were interpreted to map the void boundaries inside a karst-affected pillar. A combination of LiDAR scanning and virtual discontinuity mapping is used to formulate the discrete fracture network (DFN). Discrete element modeling (DEM) helps simulate the effect of karsts and discontinuities in the pillar models with varying stress. It is observed that the cavities may lead to a significant reduction in pillar strength. Apart from posing a hazard to miners and machinery, any advance into these cavities may disrupt mine operations. This research serves as an initial step toward understanding the importance of pillar design in underground stone mines affected by karst voids to prevent local instability or pillar failures.

Sep 1, 2022

By Nick Rose, Robert Sharon, Mark Rantapaa

Development of the Northeast Layback of Barrick’s Betze-Post open pit commenced in June 2000 and was successfully completed to a height of 400m (1,300 ft) in January 2003. Following a brief exploration drilling campaign at the toe of the final slope, in-pit waste rock backfilling commenced, which will ultimately buttress the final wall. Instability initially occurred in late 2000, above the 5040 Level, as the slope height approached 120m (400 ft). As mining reached the 4680 Level, significant deformation was experienced over a slope height of 230m (760 ft). Slope stability was managed and targeted reserve recovery was achieved by executing complicated modifications of the mine plan, including splitting layback development, well placed offloading cuts, step-outs and mid-slope waste rock buttresses. Decision on timing of these modifying events was often dictated by review of deformation magnitudes and rates determined from continuous slope monitoring records. Design modifications were developed through continuing interpretive refinement of structural geology controls and groundwater distribution, and through stability re-assessments. This document presents an overview of the geological setting and material and strength conditions of the northeast sector of the Betze-Post open pit, followed by development experience leading to design and development of the Northeast Layback. Rock mechanics modeling, design details and geotechnical performance monitoring are then presented. Development experience, stabilizing adjustments to the original design and safety procedures for development and exploration activities are described. The document is finalized with conclusions and acknowledgements.

Jan 1, 2005

Compagnie Miniere Esperance (CME), a mining company based in French Guyana, operates a gold primary ore body in open pit. The ore is processed through crushing, grinding and gravity separation. Tailings are stored in a ?fine? pond. Analyses of the fine ponds proved a residual gold grade sufficient for a chemical treatment. However, direct cyanidation would require a too large installation, regarding the local conditions (accessibility, supplying and rainforest meteorological conditions). It has been then decided to test the feasibility of a pre-concentration using flotation. Lab tests have been carried out by SGS Lakefield (Canada) in March 2007, which proves the technical feasibility. Therefore, CME asked Caspeo to: ? Carry out an on-site flotation pilot campaign. ? Design an industrial flotation circuit. The tailings reprocessing will contribute to a better tailings management and a dry up of the gold resource, limiting the risk of illegal mining after remediation of the CME site. CME MINE The Esperance gold mine is located in French Guyana, in the vicinity of several gold deposits as Omaï, Rosebel or Camp Caïman, holded by Iamgold and Newmont. These main gold deposits are located on the figure 1. Esperance was put into operation in the early 90?s. The first years were devoted to the mining of alluvial gold in the gravel of the Esperance Creek. Since then, operation was led in the primary gold deposit. Annual production is on average 254kg for a total production in fifteen years of 4300kg. Geology Esperance deposit is located in the greenstone belt of the Guyana Shield. Mineralization is in tectonic contact between sedimentary basin of Maroni and a granitic massif. Clastic series, composed of conglomerate and lamina sandstone, overlie a volcano-sedimentary basement (series called "Paramaca"). The area is strongly folded by shear movements, resulting from granite deposit. Gold is in interlacing quartz veins intersecting the clastic series. Gold is present in association with pyrite. Other elements, as silver or arsenic, are in negligible quantity. Exploitation The Maroni River is the only access to the Esperance mine. Only the saprolite and a part of the transition rock are extracted in the open pit. Excavation works are done using shovels Hyundai 450 (4 units) and haulage works using articulated dumpers Terex TA35 (4 units). These two sorts of equipments are presented figure 2. Mill The mill is composed of crushing and grinding processing plants. After gravity concentration, both plants produce tailings that are stored in two ponds: the first pond contains coarse product which segregates the particles crushed to 2mm upstream and settled clays downstream; the second pond contains the fine product made of particles ground to 200µm. These two ponds, bordered by dams and diversion canals, are located on former alluvial sites of Esperance Creek (see figure 3). [ ] The CME mill is currently producing gold concentrate, with a global recovery of about 67%. The ore is crushed by one jaw crusher and two hammer crushers. The ore then passes through a Knelson KC 48 gravity concentrator, producing a first gold concentrate. The

Jan 1, 2009

By Raja V. Ramani

As the new millennium approaches, it is appropriate to assess the progress that has been made in mine health and safety, a matter of concern to management, labor and government. One can hardly look at the major events of the last century — from the birth of the US Bureau of Mines through the enactment of the modern health and safety laws — without realizing that the march has been relentless toward eradication of health and safety threats in mining. The progress is spectacular in mine safety and significant in mine health. In looking at the future, it is safe to assume that societal demands will increase for improved health and safety conditions in the workplace. So will the demands for greater technological leaps. The standards will for measuring success and the expectations of progress in creating a safer and healthier mine environment will grow. The possibilities are enormous of meeting these exacting requirements in the 21st century.

Jan 1, 1999

By Chaoxun Zhao, Daniel Tao, Craig Blue, Narendra B. Dahotre, Rick Honaker, Bhupendra K. Parekh, Hongyang Han

Equipment wear and corrosion have significant adverse impacts on the operating cost and efficiency of mineral processing plants. In this project advanced surface enhancement technologies are being investigated to decrease the wear and corrosion rate of metal surface. Enhanced metal surfaces are achieved through surface conversion, enrichment, and coating by use of advanced High-Density Infrared (HDI) and other technologies. Studies have been done to determine the effects of process parameters on surface properties and identify optimum conditions. The microstructure of the enhanced metal surfaces was characterized by SEM, EDS, and microindentation. Laboratory wear testing was carried out to investigate the wear performance and the viable coating candidate was determined.

Jan 1, 2005

Basic parameters affecting the stability of foams have been studied. We used the thin film pressure balance (TFPB) technique of Scheludko and Exerowa (1959) to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, MIBC, and PPG. The results were compared with the froth stabilities measured using the shake tests and the film elasticity calculated using the model developed by Wang and Yoon (2006). It was found that the froth stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother concentration and type.

Jan 1, 2006

By David K. Hylbert

This study investigated roof falls in room-and-pillar drift coal mines in eastern Kentucky and utilized geologic methods for predicting roof conditions in advance of mining. In the Highsplint mine, the roof was classified in four categories or conditions: Condition A and B (Laminated Shale), Condition C (Rolling Sandstone with Shale in Pockets) and Condition D (Zone of Major Sandstone Roll(s)). Structure contour and isopach maps of the Darby coal bed and associated immediate roof rocks were used to project axial trends of the sandstone roof. Trend mapping in the mine and on outcrop provided more detailed control for roof projections.

Jan 1, 1978

By Daniel W. Kappes

Testing ores for heap leach operations traditionally follows a progression of bottle roll tests, bucket and column leach tests, and very expensive large field leach tests. Enough data is now available to streamline the procedures. Data from five different operations shows that recoveries from large field leach tests can be predicted from the bucket tests. Initial recovery times in large field leaches are longer than in bucket tests- a typical response is eight days versus twenty days to the same recovery percentage; but the ultimate percent recoveries (after 60 days) are normally very close. Methods of mining and stacking can radically affect recoveries from clay-rich ores. Leaching of uncrushed ores provides special testing problems, since accurate samples smaller than several tons cannot be taken.

Jan 1, 1981