Search Documents

By J. P. Rider

The number of extended cut mining systems has increased significantly in coal mines over the last decade, and there is a constant push to extend the face ventilation systems to even greater setback distances. The need to maintain airflow at setback distances of 12.2 m (40 ft) and beyond requires that methods for delivering intake air to the face be improved, or alternative ventilation techniques be implemented. The emphasis of this research effort was to examine various techniques to improve the distribution of available air at the mining face in order to reduce face methane levels. A study was conducted comparing the performance of a jet fan, used in conjunction with a machine mounted scrubber, with blowing curtain ventilation in a 27.5 m (90 ft) heading. In addition, a second study was performed on blowing curtain systems examining how scrubber flow, intake air velocity, and curtain setback influence face methane concentrations. Results showed that when the heading advances to a depth of 27.5 m (90 ft) blowing curtain systems were more efficient at diluting face methane levels when compared to a jet fan. Also, increases in scrubber flows and curtain velocity resulted in lower face methane concentrations for blowing curtain systems at 9.2 and 15.2 m (30 and 50 ft) setbacks.

Feb 24, 1997

The recovery of coarse particles has been widely recognized as being limited by the froth in mineral flotation. In response to this, FLSmidth has developed the Selective Froth Recovery (SFR) System. The SFR System is an extraction system that vacuums material from select locations within the froth and separates the recovered solids into coarse and fine fractions with a hydrocyclone. The SFR is supported and located by an actuator connected to the cell?s level control so that the suction heads are maintained at an offset distance from the slurry level. This can increase the recovery of coarse material by selectively recovering the material close to the bottom of the froth where drop-back of coarse particles typically takes place. The SFR System has been tested at two separate mine sites, and has been proven to increase the copper recovery in both trials. TEST RESULTS The SFR prototype was installed in a copper recovery circuit, on a rougher scavenger 160-m3 flotation cell. Figure 1, shows the SFR System, which consists of four conical skimmer heads that are plumbed together and share a common actuator. The SFR System, raised out of the froth prior to a test, can be seen in Figure 2. The SFR prototype was able to maintain a variety of set points using the level control to determine the slurry height.

Feb 27, 2013

By F. Grajales Muñoz

The Ciénega project, now under construction by Peñoles group, is located in the mountains of northwest Durango, Mexico. The gold and silver deposits are found in a 4-km (2.5mile) long system of veins. An underground operation will be built. The planned 1 kt/ d (1100 stpd) process plant will contain a countercurrent cyanide circuit for oxide ore and a flotation circuit for sulfide ore. Considerable resources have been devoted to the development of infrastructure in the isolated location, as well as for the mitigation of environmental impacts. Startup is scheduled for the third quarter of 1994. Ciénega’s ore bodies consist of quartz veins containing gold, silver, lead and zinc values. The vein thicknesses vary from 2 to 10 m (6.5 to 33 ft) with a northwest trend and nearby vertical dip. Veins are hosted in Tertiary volcanic rocks. The district has intermittently been explored since 1971 by Penoles. After the third series of diamond drilling and direct development work on vein, Peñoles decided to begin project construction.

Jan 1, 1994

By K. T. Lee, M. U. Ozbay, M. D. G. Salamon

Design of yielding chain pillars in deep coal longwall mines is not as well established due mainly to the lack of knowledge in the behavior of coal pillars in the post-peak regime. This study shows that two of the existing strain-softening models have the potential to provide an improved understanding of yielding and, therefore, could form a rational basis for yielding coal pillar design. Analytic and numerical modelings of a row of chain pillars in a two-entry development at a depth of nearly 700 m suggests that yielding pillars are feasible, but the design is very sensitive to the coal’s post-peak behavior.

Jan 1, 2001

By Jamal Rostami, Ebrahim Farrokh

Selection of tunneling method, specially the use of shielded machines for application in deep rock tunnels can be heavily impacted by presence of ground convergence and squeezing conditions. Tunnel convergence is a function of ground conditions (i.e., rock mass behavior, groundwater, in-situ stresses), size of the opening, and TBM operational parameters. The case study of Ghomroud water conveyance tunnel project in Central Iran, which is under construction using a double shield TBM, is used to examine the effect of rock parameters on tunnel convergence and hence on the need for over excavation and shield lubrication to avoid problems with the shield getting stuck. Although it is impractical to perform a continuous assessment of rock mass conditions within the shield or in the lined tunnel, results of field observations and subsequent studies show that the amount of the tunnel convergence has direct correlation with the percentage of fines and large rock fragments in the muck and TBM thrust/torque/ROP. These relationships have been examined and will be presented in this paper.

Jan 1, 2007

By Behrouz Tehrani

The size, complex issues, and requirements to construct large number of tunnels, for a single project, expeditiously, and without exceeding the overall project budget, a program Construction Management (CM) team is highly recommended to be selected early during design process to provide guidance/direction relative to contract packaging and scheduling. This paper is not focused on the project itself, however, the emphasis is on experiences gained from the project. Wishing that some of the strategies described in this paper will be of value to owners of underground project.

Jan 1, 2008

By Charles S. Robinson

INTRODUCTION Geology, the science of the earth, is the fundamental science in the construction of a tunnel. The approximate site of a tunnel is determined by its purpose. The geology of the tunnel site will determine the cost--or feasibility of a tunnel--the specific alignment to accomplish the purpose of the tunnel, the design of the tunnel (within the limits of the purpose of the tunnel), and the methods of construction. The more accurately the geology of a proposed tunnel can be depicted, the more accurately can the cost of a tunnel be estimated. The factors that should be defined for tunnel design and construction are the physical characteristics of the material in which the tunnel is to be constructed. The physical characteristics of the material are determined by the genesis of the material, and subsequent geologic processes that have affected the material. The geologic materials in which tunnels are constructed can be broadly classified as unconsolidated and consolidated. The unconsolidated materials include chiefly deposits of recent geologic time that occur near the surface. Because these deposits occur near the surface, and tunnels constructed in them will be at shallow depth, methods of physical exploration such as geophysical methods, trenching, and drilling will give more data at relatively low cost--therefore the physical exploration is generally, or should be, quite extensive--and the

Jan 1, 1997

By George Anagnostou

Time-dependent ground behavior may have important implications for the construction process or the life of a tunnel. The paper gives a concise overview of the influence of time on the deformations and the stability of underground openings, including topics such as face stability in soft ground or the time-development of pressure or deformations in squeezing or swelling rock. While keeping in mind practical questions of tunnel engineering, emphasis is placed on understanding the observed time-dependency, on the underlying mechanisms (such as pore water pressure dissipation or chemical processes) as well as on the respective inherent prediction-uncertainties and design-uncertainties.

Jan 1, 2007

By Walter R. Hibbard

Precipitation in the northeastern United States, Florida, California and in many industrialized areas of the world is now more acidic (lower pH) than can be accounted for by natural causes. At the same time, the acidity of many lakes and streams in the northeastern United States has been measured and found to be similar to that of actual rain. These facts have led to conclusions that the two conditions are related. Coal burning utilities, 700 to 1000 miles upwind, have been accused of being the cause, leading to proposals for strict emission controls on the alleged offenders. The costs of these controls would place an estimated $10 to $15 billion capital burden on utility customers in about 15 states plus $2 to $6 billion annual operating costs. There appears to be no direct well-established scientific evidence that the accused are guilty but that the indictment is based largely on circumstantia1 evidence. This study examines the evidence, describes the situation and proposes what must be done to reduce the acid precipitation in an orderly cost beneficial manner. It is interesting to observe that studies by the different adversaries on the acid precipitation issue come to different conclusions largely because they do not read the same literature, but selectively develop evidence to support their own points of view, This study will try to review the issues impartially and reach a position of scholarly balance.

Jan 1, 1982

By Betty Gibbs

The Ore Body Modeling and Mine Planning Worshop, sponsored by the Society for Mining, Metallurgy, and Exploration, Inc. (SME), was held Feb. 22-24, 1991 before the SME Annual Meeting and Exhibit in Denver, CO. More than 40 people from mining companies, government agencies and universities attended. Eight vendors of integrated ore body modeling and mine planning software attended and presented the results of problem sets given before and during the workshop. They were: [ ]

Jan 1, 1991

By J. Evans

Including: Tailings thickeners, CCD?s, paste thickeners, HI-rate thickeners, lamella thickeners, high compression thickeners, clarifiers etc. Flocculant dosing control for mining thickeners and clarifiers is influenced by a number of process factors. 1. Flow rate into the thickener or clarifier a) As the flow rate increases into the thickener or clarifier ?retention time? decreases which causes a greater affect hydraulically on the settling solids. So as the flow rate increases it will generally mean an increase in flocculant dosing rate. b) As the flow rate decreases into the thickener or clarifier the retention time increases which reduces the hydraulic affect on settling, improving settling rates. This will generally mean that as the flow rate decreases, we will decrease the flocculant dose rate.

Jan 1, 2011

By W. X. Wang

In the mining and quarry industries, rock fragments are often transported by conveyor belt. To estimate the qualities of the rock fragments (i.e., size distribution and shape), an operator must take samples from the conveyor and manually perform a sieve analysis, which is time-consuming and tedious. Alternatively, an image-analysis system can be used to monitor the fragment quality on a fast moving conveyor belt. However, images of fragments on a fast moving belt vary to such a degree that the quality of any two successive images are not the same, and some of the images are of such poor quality that they are unrecognizable by human eyes. If poor-quality images are directly analyzed by a segmentation algorithm, the analysis will not be satisfactory. To resolve this problem, it is necessary to use an image-classification pro-gram for the automatic selection of fragment images with good quality. Because of this need, an image-classification program was developed and tested both in the laboratory and in the field. Testing of the system on different types of fragments showed that the system works reasonably well.

Jan 1, 1996

By Russell Clough

The Pacheco Pumping Plant is situated on the west end of San Luis Reservoir in western Merced County, California. It is designed to draw water from the reservoir and pump it into a 3,500,000 gallon regulating tank. The water then flows entirely by gravity to the Coyote Pump Station in Morgan Hill, a distance of 40 miles, where it is pumped into Anderson Reservoir. This water is used to recharge the depleted groundwater table in the Santa Clara Valley. Eventually, some of the water will be diverted to Hollister in San Benito County and to Watsonville and Santa Cruz in Santa Cruz County. The owner is the United States Bureau of Reclamation. The underground work consisted of a fifteen foot finished diameter surge shaft 250 feet deep to the crown of the pump chamber; a twenty foot finished diameter pump chamber which declined from the shaft at 14.2% for ninety feet and then ran horizontally for 180 feet; and twelve each five foot diameter steel lined intake shafts 240 feet deep which intersect the pump chamber in the horizontal section. (Figure 1) Upon completion of the pump chamber, the contractor had to dewater the existing tunnel under the reservoir, excavate the remaining fifteen foot plug, and concrete the transition. The low bidder for this contract was Underground - Continental-Heller at 414,456,000. Excavation of the open cut for the pumping plant and surge shaft began on April 14, 1983. This was performed using a Koehring 1066D backhoe, dozer, trucks, and two Cat 631 scrapers. The excavation was started at the surge shaft so that the grouting could begin

Jan 1, 1985

The National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine the effectiveness of a filtered air delivery system to reduce respirable dust exposure to roof bolter operators in underground coal mines. When performing roof bolting operations, roof bolter operators may experience exposure to high levels of respirable dust during a working shift, especially when working downwind of the continuous mining machine. While drilling and installing roof bolts, this filtered air system supplies a clean curtain of air over the roof bolter operator by means of a plenum mounted beneath the canopy. This experimentally designed air curtain, adapted for roof bolting machines used in this study, is based upon previous design prototypes, computational fluid dynamics (CFD) simulations, and trial-and-error testing. Both prototype and final designs were tested in the full-scale mining galleries at the Office of Mine Safety and Health Research (OMSHR) in Pittsburgh before being taken underground for field testing. Test results of the system in both laboratory and field studies show reductions in operator exposure to respirable dust when the operator is positioned directly under the protected zone of the canopy.

Jan 1, 2012

By R. W. Chappell, M. W. Hills, R. L. Olsen

A stochastic approach was developed and applied to the Butte, Montana Hillside abandoned mining site for modeling stormwater runoff and subsequent receiving stream loadings. This approach enabled capture and quantification of the uncertainty associated with stormwater quality data and allowed the prediction of copper and zinc concentrations in the receiving stream caused by runoff from the Butte Hillside during storm events. Runoff flows and stormwater concentrations were input to the model as probability distribution functions. Monte Carlo simulation allowed prediction of expected instream concentrations in the form of cumulative distributions functions. The modeling results allowed evaluation of current best management practices (BMPs), targeting of future BMPs, and identification of key data gaps to fill during future sampling activities. This modeling approach is considered extendable to other active and inactive mining sites. Output from a model of this type is easily understood and can be used to communicate effective stormwater management to site regulators. Furthermore, application of this modeling approach will facilitate the development and implementation of a site-specific stormwater management plan and will optimize efforts to achieve standards for compliance with stormwater discharge permits.

Jan 1, 2002

By Frank P. Frandina, Michael J. Loehr, Paul E. Gabryszak

The Heartland Corridor Clearance Improvement Project is part of a regional Public-Private initiative to allow double stack container trains a direct route from the Port of Norfolk through Virginia, West Virginia, Eastern Kentucky and into Central Ohio. In the Preliminary Engineering stage, 30 existing tunnels were assessed and 28 were found to need clearance improvements to allow the use of double stack trains. Alternative tunnel enlargement methods were developed to achieve the desired clearance improvements, while maintaining structural integrity and minimizing disruption to train traffic. This paper summarizes the geometric and condition investigations of the existing tunnels, as well as describes the preferred methodologies to achieve the desired clearance. The clearance improvements will be implemented beginning in the summer of 2007.

Jan 1, 2007

By Timothy D. Arnold

Barrick Gold’s Bullfrog underground mine, near Beatty, NV, was established as an after-thought to the main open pit. As open pit ore dwindles, the underground mining became increasingly more important as an ore source, and to the overall economics of the project. This situation is similar to many other mines. Today, there is a move towards underground mining in the United States. There are inherent problems in starting and operating underground mines in the shadow of any open-pit operation. Several attempts were made at the Bullfrog Mine for productive increases. Some were successful, while others were not.

Jan 1, 1996

By David Smith

Construction of a new transportation link frequently requires crossing under an existing highway or railroad. Although traffic diversions may permit a cut and cover structure to be built, ‘zero impact’ tunnel solutions are becoming increasingly popular. The vertical clearance between the new tunnel structure and the existing highway or tracks may be very low; sometimes less than two meters. This leaves little room for error since any ground loss can rapidly translate into surface settlement. Problems can be avoided by maintaining the stability of the tunnel face and by minimizing ground movement around the tunnel lining. This paper examines construction methods that have been used to construct short tunnels with shallow cover, and highlights factors to be considered for future projects.

Jan 1, 2005

By George K. Schenck

INTRODUCTION Recent advances in high-pressure water jet technology can be effectively employed in mining and tunneling. The new equipment is based on available industrial hardware such as pumps, nozzles, and rotary swivels and seals, and is compatible with present mining and tunneling techniques. Principal advantages of water-jet assisted cutting relative to standard cutting are higher production rates, lower dust levels, and reduced fines. When used on rock and coal miners, water jets mean that relatively smaller and cheaper machines can be purchased. If properly applied, the combined effect is lower cost and significantly improved health and safety. While commercial use of high-pressure water blast cutting and extraction of rock (and concrete) already has a firm foothold in Europe, application of this new technique is just beginning in America. This paper begins with current American applications of high-pressure water jets for drills, for slotting and channeling machines, and then discusses the emerging technology for initiating rock failure in conjunction with drag bits on coal plows, continuous miners and boom-type miners (roadheaders). The focus of this paper is use of high-pressure water jets for cutting rock. High-pressure water jet cutting utilizes water above 70 MPa and currently reaches to 300 MPa and above. Some informatfon is included on low pressure "wethead" coal shearers and boom miners with water pressure to about 15 MPa.

Jan 1, 1983

By D. J. Gilbert

As a preventive action, the geotechnical department at the mine analyzed the original topography overlying a conveyor tunnel at the mine. Several dewatering drains were installed to intercept water collecting from an old lakebed. Subsequently, 20 steel arches were installed to provide additional support in an area of tunnel where original geological mapping indicated Type IV rock. This project was completed ontime with no loss to production. Construction schedules had to be developed to half hour precision, to accommodate the installation.

Jan 1, 2011