Search Documents

By Richard R. Klimpel

INTRODUCTION Previous papers by this author have discussed some of the difficulties involved with optimizing the performance of industrial flotation circuits, e.g. Klimpel (1988, 1989). The two major problems seem to be: 1) the inherent "systems" nature of the froth flotation process which leads to a great deal of self-compensation among the various operating options available and 2) the inherent variations in mineralogy, water chemistry, etc. that always seem to be present in industrial operations. In particular, the influence of reagent dosage has been emphasized in the above referenced work including an industrial system interaction denoted as the R/K trade-off, Klimpel (1984, 1987). Using a simple two parameter model for fitting time - recovery data, Klimpel (1980): [ ] where r is cumulative recovery at time t or at the t th cell, R is the long-term equilibrium recovery and K is the first-order rate of mass removal from the cell (time ), the definition of the R/K trade-off with increasing reagent dosage can be given as follows: at low dosages both R and K increase, at intermediate dosages R continues to increase but K starts to level out, and at high dosages, R may flatten out or still continue to increase but K starts to decrease, sometimes rather quickly. An illustration of this effect in a batch laboratory flotation cell is given in Figure 1. The purpose of this paper is to give a detailed plant illustration of this R/K trade-off phenomena with changing collector dosage which shows just how highly interactive the grindinglflotation system in sulfide mineral processing really is. This is one of about 20 plant level case studies that are being presented and evaluated in an upcoming book, Klimpel (1990). The particular study given here was completed in late 1979 on a copper ore of head grade 0.93% Cu. The frother being used was Dowfroth* 250 at a constant dosage of 0.15 g for each ton of solids feed to the rougher bank and the slurry pH was 10.2. The motivation of the study was to better understand the relationship of changes in feed rate (hence in particle size and state of liberation) with variations in collector dosage (potassium amyl xanthate). The major concern was to determine how much extra economic benefit could be gained by better utilizing the existing grinding mills and rougher bank consisting of eight identical cells. The remainder of the flotation circuit was also studied, including regrinding of rougher tails, but did not prove as critical as the rougher bank operation itself. It appeared from an overall economic viewpoint, the battle was being won or lost in the manner in which the rougher bank was being operated. This was not to minimize the roles of the scavenging and cleaning circuits but those portions of this particular circuit could be rather obviously operated to achieve maximum benefit given the specific output of the rougher bank. A special attempt was made to maintain constant ore type throughout the entire test program. Eight specific test conditions were evaluated including three different feed rates (and hence three different size distributions) to flotation. Tables 1 and 2 summarize the eight test conditions and overall recovery results at the end of the rougher bank for each test. A single test consisted of at least three consecutive eight-hour shifts operating at steady-state with composite cell lip samples taken over the final eight-hour shift. "Trademark of The Dow Chemical Company

Jan 1, 1990

By W. Jacobi, F. Steinhausler, A. C. James

INTRODUCTION In 1979 the Committee on Radiological Protection and Public Health of the Nuclear Energy Agency (OECD) defined a programme of work needed to improve radon dosimetry and monitoring. A Group of Experts in this field was established by the NEA and at the first meeting of the Group the authors were designated an initial task with the following terms of reference:- To review dosimetry of radon, thoron and their daughters, and in particular:- - to examine analytical models for the assessment of dose to individuals who are exposed to aerosol mixtures of these nuclides; - to examine the state of knowledge of the characteristics of aerosol mixtures of these nuclides and other factors that influence the dose to the lung, and identify those parameters which should be measured for dosimetric purposes in radiological surveillance programmes; - to identify areas where further study or research are needed. In this presentation we attempt to examine, with these objectives, the relationship between exposure to radon and thoron daughter aerosols expressed in terms of the working level month l (WLM), or its SI equivalent, and dose accumulated by sensitive tissues of the lower respiratory tract. Over the past two decades many attempts have been made to calculate the lung dose equivalent to l WLM exposure in mine atmospheres, usually in terms of the maximum dose to basal cells in a small part of the bronchial tree. The calculations have employed variously detailed models of airway anatomy, aerosol deposition, ciliary clearance and dosimetry of tissue at the bronchial surface, and are well reviewed elsewhere (Walsh, 1970; UNSCEAR, 1977; Jacobi, 1977; Fry, 1977). They agree in the conclusion that basal cells in segmental bronchi (between about the third and fifth bronchial generations) receive the highest dose, although estimates of this dose differ by more than an order of magnitude, ranging from about 0.2 to 12 rads per WLM (2 mGy to 120 mGy). The most critical parameters of these models are the assumed depths of basal cells below the bronchial surface and the fraction of the WL carried by free ions. When more realistic values of these parameters are substituted (Jacobi, 1977), the dispersion in calculated maximum doses to basal cells is reduced to give a much smaller range from about 0.3 to 1 rad/WLM (3 to 10 mGy/WLM). The parameters and methods employed in these various models, however, remain too diverse to infer the sensitivity of the dose conversion to practical variations in aerosol characteristics and the additional factors determining lung deposition and clearance. We have therefore taken the approach of developing newer models (Jacobi and Eisfeld, 1980; James et al, 1980) that can encompass the range of available experimental data on the physical and biological behaviour of radon and thoron daughters and also accommodate the different interpretations that can be put upon them. We have paid particular attention to the averaging of dose over tissues of equal sensitivity in the lung

Jan 1, 1981

By E. K. C. Chanda

The best use of available reserves to give good metal recoveries relies on short term mine production scheduling.-The aim is usually to produce a plan to guide mining in specific areas that will enable mine operations to deliver the budgeted tonnes and grade to the mill and keep within the long range mine plan. Thus, short term production scheduling is an important aspect of the open pit mine planning function. Since the 60's increased attention has been paid to effective production scheduling as a means of improving the economic viability of existing mines. Hence, mine scheduling scheduling systems have been evolving rapidly during the last two decades. These systems include manual techniques, computer based simulation, mathematical programming and more recently Computer Aided Design (CAD). Some general drawbacks of the current scheduling systems are that firstly, the costs of acquiring and using them are not at all insignificant especially for small to medium sized pits. Secondly, there is an inherent trial-and-error aspect in these systems. Thirdly, they tend to be suited for specific orebody geometries, hence lacking the necessary generality. For instance, the use of computer programs for planning open pits to mine stratiform orebodies raises problems which are not usually met when massive orebodies are considered. There for, a need exists to develop simpler but effective short term pit scheduling procedures suitable for stratiform type orebodies, considering their geometry and geology. This paper describes a PC- based model designed to assist the planning engineer in optimizing the short term production schedule in open pit mines with stratiform orebodies. The model is based on a combination of linear goal programming and deterministic mining simulation. The orebody model is made up of ore and waste mining regions where winning and and/or stripping are taking place. These shovel regions form the basic planning elements in the model. This approach does not require the laborious preparation and use of a regular block model. The computer program consists of main modules: (i) Data capture - processes the raw data into the required format for mine planning. (ii) Precedence mining constraints - checks the status of each shovel .region at the beginning of a given scheduling period with regard to geometrical mining constraints such as undercutting. (ii) LP- Optimization - provides an optimal selection of ore shovel regions which do not violet geometrical constraints for mining in the period, the objective, being to maximize the contained metal equivalent in the blended R-O-M ore and at the same time to minimize deviations in grade and tonnage from the call values. (iv) Post LP-Simulation - enables the user to smooth out the LP solution in order to adjust it to a practically executable plan and simulates mining of ore and waste for the period. Shovel allocation to selected ore and waste shovel regions, unit operations and depletion of reserves are executed in this module. Preliminary testing of the model for monthly production scheduling using data from Nchanga OPen Pit on the Zambian Copperbelt indicates that it can be a useful planning tool and gives acceptable results.

Jan 1, 1992

By T. Moller

There are differences in design aspects between steel and rubber linings in grinding mills. This paper describes the basic design rules for rubber liners for different grinding applications. When converting a mill from steel to rubber liners, the design must be changed from such familiar steel liner shapes as wedge bars and plates, wave liners, ship-lap, etc. to take advantage of the characteristics of rubber. Very little of the knowledge of the wear properties of steel can be used for the design of rubber mill liners.

Jan 1, 1989

By T. B. Szwilski, R. D. Begley

Status of ISO 14000 standards. The ISO 14000 are voluntary international standards providing a frame-work that allows a company to integrate an effective environmental-management system (EMS) into its operations. The purpose of an EMS is to provide a systematic procedure to identify the environmental aspects of a company's activities, evaluate any significant impacts and use the information to set objectives and targets toward continuous improvement of the company's environmental compliance and performance. In addition to the specifications for certification, ISO 14000 can be used as a guide to develop an effective environmental-management system or for self-declaration. The International Organization for Standardization (ISO) is a worldwide federation founded in 1947 to promote the development of international manufacturing, trade and communication standards. The organization is now represented in 118 countries, with the American National Standards Institute (ANSI) representing the United States. The principal goals of the ISO is "to promote the development of standardization and related ac¬tivities in the world with a view toward facilitating the international exchange of goods and services and to develop cooperation in the sphere of intellectual, scientific, technological and economic activity." ISO develops standards with input from government and industry. Because the standards are voluntary, there are no legal requirements to pressure countries to adopt them. However, many governments, industries and US agencies are adopting the ISO standards as a requirement for business trans¬actions, thereby, compelling suppliers to adopt ISO standards. These business and market forces, which are likely to be strategic business issues in the 21st century global marketplace, are imposing the need to develop a systematic approach to environmental management. The ISO 14000 series evolved from a United Nations Conference on the Human Environment in 1972. It includes a broad range of elements: the basic environmental management system, environmental auditing criteria for internal and external auditors, criteria for environmental performance evaluation (EPE), environmental labeling criteria and life-cycle assessment methodologies. The standards comprise two categories: organization evaluation standards and product oriented standards (Table 1). The ISO 14001 specifications contain the requirements for developing an environmental-management system that may be objectively audited for certification. The ISO 14004 standard provides guidance on interpreting the ISO 14000 specifications for the development and implementation of the EMS and for coordination with the management system of the company. On Sept. 1, 1996, the American National Standards Institute (ANSI) and the Registrar Accreditation Board (RAB) signed a formal agreement to create a new entity called the National Accreditation Program (NAP). To obtain certification, a company must fulfill the requirements outlined in ISO 14001. It is required that "a third party give written assurance that a company's EMS meets all the requirements of ISO 14001." Preparing for ISO 14000 can include subscribing to voluntary environmental initiatives; learning from ISO 9000 quality-management experiences; and utilizing information from recognized training courses, publications and numerous Internet resources. Once committed to an EMS, the management should provide sufficient resources to achieve continuous environmental-performance improvement, as outlined in an environmental policy. A thorny issue now being debated concerns the potential liabilities of documenting the environmental performance of a company. General impact of the ISO 14000 EMS standards. With increasing stakeholder awareness, costly end-of-pipe pollution-control approaches and the success of ISO 9000 quality-management standards, the ISO 14000 EMS standards are being adopted by companies and governments worldwide. The United States and Canada have well-established programs. In Europe, countries differ but are firmly committed toward environmental-management standards (BS 7750, EMAS and ISO 14000). The Department of Environmental Protec¬tion of the State of Pennsylvania is using ISO 14000 as a vehicle to develop a closer working relationship with industry, and it is anticipated that this policy will eventually lead to fewer environmental site inspections for those companies with ISO 14001 certification. The Depart-

Jan 1, 1999

By Erik Westman, Enji Sun, Xu Ma, Ben Fahrman

"Shale gas has become an increasingly important clean energy, which has been explored worldwide in recent decades. Supercritical CO2 acts as fracturing fluid for shale gas production. The safety monitoring is essential to prevent any kinds of leakage from the reservoir as the supercritical CO2 physically stored hundred kilometres underground. Seismic tomography is an imaging technique that uses induced seismic waves to create three dimensional images of the subsurface. It is an effective monitoring method to evaluate the caprock integrity in the carbon dioxide sequestration storage (CCS). In this experimental research, a simulated uniaxial compressive load is applied on a granite sample to analyze the stress redistribution for long-term in-situ caprock integrity during CO2 injection. The induced seismic waves are recorded and seismic events are traced based on the Geiger algorithm. The frequency of seismic events correlates with the caprock failure evolution. The acquired seismic data is divided into four regimes based on the frequency of seismic events and the failure process to examine the failure evolution. Furthermore, the travel time and distance is plotted to analyze the variation of velocity. Finally, the double difference tomography (TomoDD) algorithm using arrival time is adopted to recalculate the locations of seismic events and velocity structure in each regime. The results indicate that the passive seismic system can map the caprock stress distribution and allow for imaging of the caprock integrity. TomoDD exhibits sound improvements to relocate seismic events both in relative and absolute locations as well as to characterize the local velocity structure. The study further reveals that seismic monitoring along with TomoDD could evaluate the caprock failure accurately in the CCS.Introduction To reduce the CO2 concentration in the atmosphere, CO2 capture and sequestration (CCS) has been suggested to as a means of continuing to use fossil fuel resources while offsetting their negative environmental impacts (Eiken et al 2011). A positive CCS project should retain 99% of the injected supercritical CO2 (pressure is greater than 7.38 MPa and temperature is above 31.04? and a density is of about 700 kg/m3) over at least 100 years (Davidson et al 2005). As large quantities of supercritical carbon dioxide are being injected into full scale storage projects, caprock stress is redistributing and the leakage could occur anywhere over a wide storage area (Hou et al 2012). Acoustic waves are emitted from the caprock, as it fractures due to the CO2 injection, which can be detected by passive seismic sensors (Shitashima et al 2013). Tomography techniques are advantageous for imaging the integrity of the caprock in the CCS projects. Velocity tomography uses waves to model entities based on the arrival time of waves (Westman et al 2001, Westman 2004, Luxbacher et al 2008). Seismic tomography is a data inference technique that exploits information contained in seismic records to constrain 2D or 3D models of the Earth's interior. It generally requires the solution of a large inverse problem to obtain a heterogeneous seismic model that is consistent with field observations (Kudryavtsev et al 2012)."

Jan 1, 2017

By S. A. Diatchkov

Introduction There is a misconception that mineral-project economic evaluations in the former Soviet Union are either nonexistent or very limited. This is not the case. In fact, there are at least two basic methods that can be utilized to evaluate the vast mineral resources of the Commonwealth of Independent States (CIS). Evaluation procedures are based either on a comparison to known projects, which may rely on limited available data, or on potential-profit calculations, which generally uses more extensive databases. Significant philosophical differences between these systems and those utilized in the Western world include the following: •Under the centralized-government system, the economic evaluation of a mineral project was based on artificially determined mineral prices and costs. Every ten to 12 years, prices for concentrates and metals were established by the Council of Ministers and remained unchanged until the next reconsideration of prices . •The time value of invested money was not considered to be important under these "stable" prices, and inflation was assumed to be nonexistent in the planned economy. •An overestimation of the value of social and economic factors such as keeping the local population employed and providing the country with strategic minerals biased the economic evaluations of projects. Sequence of exploration Geological exploration in the CIS countries typically includes two major phases: prospecting and exploration. Prospecting consists of the following: •Regional geological studies. •General prospecting. •Prospecting. •Prospect evaluation. Regional geological studies are conducted within large territories and utilize satellite images, deep seismic zoning and other state-of-the-art methods. Geological and geophysical maps on a scale of from 1:200000 to 1:1000000 are developed to help identify regional anomalies and mineral prospective areas. The areas of primary interest are then subjected to general prospecting, beginning with geological mapping of the area at 1:50000 (1:25000) scale. The prospecting phase determines mineral potential based on further geological mapping (mostly 1:10000 scale), surface geophysics and geochemistry. Finally, the most attractive targets are subjected to further detailed evaluation (prospect evaluation) to help identify "possible" projects by means of trenching and wide-spaced drilling. The results of the prospect evaluation are analyzed and conclusions regarding the economical potential of the project are drawn. If the initial-prospecting phase results are positive and the prospect is recognized as economical, it then moves into preliminary exploration, which is followed by detailed exploration. Preliminary exploration determines the feasibility of the project on the basis of limited data. For example, in some underground projects, the initial exploration drilling and tunneling is done at two or three times wider spacing than would be required by the assumed mining method. Detailed exploration focuses on preparing the project for mining development, such as completing drilling and tunneling, particularly in the portion of the ore body to be first mined. During the project's mining phase, further exploration is usually conducted along the flanks of the mineralized structures and deeper sections of the ore body. Finally, during exploitation, it is sometimes necessary to delineate the ore body within the mining-block limits. A comparison between the United States (US) sequence of exploration activities and the CIS system is given in the Table 1. There is no "additional" and "exploitation" exploration shown in the US system, but it is common knowledge that all mineral projects are subjected to "additional" and "exploitation" exploration while being mined. An economic evaluation should be performed after the [ ]

Jan 1, 1996

By John C. Franklin

INTRODUCTION Alpha-emitting radon daughter products are a recognized health hazard contributing to the development of lung cancer in persons exposed to excessive concentrations over an extended period. The primary control technique used by the mining industry is dilution with fresh air. Because the uranium is deposited in porous sandstone in most U.S. mines, the control of this hazard with dilution requires excessive volumes of air. As the mines become larger and deeper, the cost for ventilation becomes a major expenditure for the mining industry Most mines are maintaining levels of radon daughters lower than required by law but to maintain these present levels the mining companies are going to be drilling more vent holes or using other control techniques as the mine expands. These control techniques are being investigated by the U.S. Bureau of Mines to determine their effectiveness, cost, and safety for underground use. [Instrumentation] The Bureau's early research used batch sampling of both radon and radon daughters for determining the concentrations. In both cases it was determined that batch sampling did not give a complete understanding of what was happening to the concentrations. Therefore, continuous monitoring systems were developed for both. A continuous flow-through radon monitor was developed by the Bureau (Franklin, et al.., 1976) using a modified Lucas flask mounted on a photo-multiplier-tube (PMT). The air was filtered twice prior to entering the flask to remove dust, diesel smoke, moisture, and radon daughters. The signal from the PMT was then inverted, shaped, and driven to a data acquisition system (DAS) which accumulated the signals. The DAS has two comparators for setting the scan time and interval, a 24-hour clock with Julian date, a printer, and a perforated paper tape punch. Sampling time is determined by the type of experiment being conducted. Our normal sampling time is one 10-minute scan every 15 minutes, but could be set as low as one scan every minute or as long as a 16-minute scan every 167 minutes. There are two models of the DAS. One is a 10-channel system and the other a 30-channel system. On a 10channel system normally 6 channels are used for radon and radon daughters and the other four channels are used for temperature, absolute pressure, air velocity, and relative humidity as described by McVey (1977). Figure 1 shows a scan of five channels monitoring the radon concentration from intake to exhaust in a stope for a non-work day. If the radon concentration stayed this constant during work days, then continuous monitoring would not be necessary. [ ] Droullard (1977) developed a continuous alpha-beta monitor. This monitor has been modified so that it can be used with the DAS previously mentioned. Control Techniques The U.S. Bureau of Mines has conducted research in controlling airborne radon/radon daughter for 10 years. Major efforts have been conducted in sealing the rock to prevent the release of radon, bulkheading to seal nonproductive areas, backfilling with classified mill tailings, and positive pressure ventilation. Also, tests have been conducted to determine the mining cycles contribution to the radon problem. Surveys One stope with two intakes and one exhaust was continuously monitored to determine the effects of blasting, mucking, and drilling on the airborne radon concentrations (Franklin, et al., 1976). Two other detectors were located inside the stope which were close to the mining activity. In this stope no appreciable change in radon was observed during drilling holes for blasting and roofbolts. This study showed increases up to 40 percent in radon for slushing in the exhaust drift. The radon remained high and very eratic during slushing, as can

Jan 1, 1981

By Julian Brown, Steve Hicks, Zach Agioutantis, Zachary Wedding

Analysis of Coal Pillar Stability (ACPS) software, released in 2018, integrates numerous empirical pillar design techniques. The ACPS program incorporates methodologies originally available as design tools from the National Institute for Occupational Safety & Health (NIOSH), including Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Analysis of Multiple Seam Stability (AMSS), and concepts including Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar formula, and pressure arch loading. The design methodologies that are the basis of ACPS were developed via analysis of significant amounts of real-world data and have been standards of the United States coal industry for decades. While there are empirical factors built into ACPS, making it ideal for use in U.S. coalfields, the concepts in the program have proven to be applicable in variable mine settings, and the software was developed to allow for user-based, site-specific modifications of key design inputs. Application of ACPS to cases outside the regions for which it was developed must be approached carefully, and continuous development of site-specific data is mandatory. A case study is presented involving the application of ACPS to assess pillar stability and assist future design for an underground lignite mine in Eastern Europe. Assessment of in-mine observations, review of the geology of the lignite mine, and evaluation of specific conditions associated with a failure event resulted in “calibration” of key input factors to ACPS. Scenarios evaluated with ACPS suggest that pillar strength and overburden depth are key factors for the determination of pillar stability and design in future areas.

Jun 25, 2024

By G. M. Wali Ullah, Micah Nehring, MEHMET KIZIL, PETER KNIGHTS

In operations that use the sublevel stoping mining method, production scheduling takes into account factors — including ore reserve envelopes, ore grade averages, equipment capacity, feed controls to the mill, and geotechnical restrictions — across the scheduling horizon. Mathematical programming is one of the most effective methods for enhancing the decision-making process in regard to the most viable production schedule in light of a given set of limitations. The majority of research on sublevel stope mining focuses primarily on a single objective of optimization, which is to maximize the net present value (NPV). Environmental, social and governance (ESG) considerations are becoming more prevalent in the mining industry. This includes aspects relating to deforestation, land disturbances, gas emissions, community relations and water usage, among many others. Institutional and other kinds of investors are becoming more interested in the work that resource companies do regarding their ESG obligations. This review article identifies the gap in the existing literature and proposes to simultaneously optimize the production schedule around three objectives. Two of these relate directly to ESG aspects

Jul 1, 2024

By W. M. Kidd

INTRODUCTION Uranium mine inspection in Canada forms one element of the enforcement of the Atomic Energy Control Act; it is under this Act that all Canadian uranium mines and mills are licensed to operate. Inspection duties are carried out by a small core staff of federal government inspectors (working for the Atomic Energy Control Board (AECB)) largely supplemented by provincial mine inspectors working on behalf of the AECB. Unlike most resource extraction in Canada, uranium mining is under federal jurisdiction and consequently it was the AECB who decided in 1975 that changes in the Canadian uranium mining industry, particularly its expansion and the expanding role of the mine inspector in the limiting of exposures, warranted the offering of a special radiation protection training course. The Uranium Mine Inspector Training Course (UMITC) was first conducted in 1976 at the Elliot Lake Centre in Elliot Lake, Ontario. Subscription for the course was not limited to mine inspectors to enable union stewards, management personnel and provincial/federal labour inspectors to attend. This paper will present an outline of the course content, the format of its presentation and non-curriculum aspects of running a course of this type in uranium-producing community. The core lecturers for UMITC are drawn from the Radiation Protection and Uranium Mine Divisions of the AECB. In addition, guest lecturers are invited from universities and medical research centres together with industry professionals and government researchers. In all some twenty-four plus presentations are made over the first five days of lectures. The program topic areas, hazards, controls, measurements, record-keeping and health effects are preceded by an intensive half-day session on radiation fundamentals. TOPICS Hazards [Dust] A review of the dynamics of airborne particles including the effects of particle size, gravity and wake-turbulence on the behaviour of dust clouds. Associated topics are migrational aspects of dust particles and specific dust-generating mine operations. [Radiation] Canadian uranium mines are increasingly diverse in nature ranging from large scale low-grade underground operations in Elliot Lake to smaller high-grade open pits in Saskatchewan. Papers are presented on assessments of internal and external exposure, the metabolic pathways of ingested or inhaled radiation and the specifics of mine and mill hazards. Radiation hazards are further broken down into gamma surveys of uranium mines, radon daughter concentrations and problem areas. Controls The relationship between mining methods and the operating environment is critically important to ensuring safe working conditions. This refers to both the selection of machinery/devices, etc., and to engineering controls which are instituted to remedy problems created by new technology. UMITC examines a number of possible mining techniques, their criteria for selection and impact on the working environment. Control measures, ventilation practices and design, the need for continuous water misting and special open-pit precautions are presented. These lectures frequently conclude with suggestions for better operating guidelines for mine ventilation systems and the need for greater co-operation between the ventilation department and the underground crews. Measurements Uranium mining regulations stress the need for a high standard of exposure monitoring, statistical planning and record-keeping. [Statistics] Although many course participants are well versed in statistics, certain fundamentals are repeated and include, the concepts of mean, variance, standard deviation and standard deviation of the mean. Confidence levels, decision-making based on sample statistics and statistical records are also discussed. [Dust Measurement] Dust measurement is particularly critical in the mines where the high silica content of the ore body, such as those at Elliot Lake, results in the continuous generation of dust. Sampling practices, filtration, impaction, thermal impaction and electrostatic precipitation are explained together with the methods of counting samples to determine free silica. Konimetric and gravimetric techniques for dust sampling are compared and contrasted. [Radiation Measurements] Both collective and personal dosimetry systems are used in the Canadian uranium mining industry and lectures are presented on each. Techniques and possible sources of error are discussed for a variety of radon and radon daughter measurement methods - Lucas method, Tsivoglou and modified Tsivoglou, Kusnetz, Rolle. Instant working level meters and personal alpha dosimeters are explained in terms of calibration, maintenance, readout and estimation of accuracy. A lecture outlining dose estimation by means of bio-assay, whole-body counting and the use of TLD's concludes the topic. Record-Keeping An overview of the problems of changing limits,

Jan 1, 1981

By B. P. Boisen

INTRODUCTION Application Measurement of rock deformation is essential to stability and behavioral monitoring of underground openings. The difficulties of obtaining adequate sample distribution, density, and orientation can frequently be overcome by the use of single and multiple position borehole extensometers. In its simplest form, a borehole extensometer consists of an instrument head, usually anchored in the collar of a borehole, and a number of in-hole anchors, each of which is fixed in place at a known distance from the collar. As rock adjacent to the borehole deforms, the component parallel to the borehole direction causes a distance change between adjacent in-hole anchors, as well as a distance change between individual anchors and the instrument head. These changes are measured by means of a mechanical link (usually wire or rod) extending to the instrument head from each anchor. The resulting data can be used to compute the distribution, magnitude, rate, and acceleration of deformation in the material intersected by the extensometer's borehole. Wire Vs. Rod Extensometers Since the early 1960s myriad varieties of borehole extensometers have become available through the combination of various special features of two basic instruments, the wire and rod versions of borehole extensometers. Recent publications have recommended shallow depth limitations for wire extensometers, and favor rod extensometers for a broad range of borehole inclinations and depths. There are three main reasons for using a deep wire system: its cost effectiveness; the fact that tremendous depth means tremendous rod weight which will cause the rod to buckle or rub against the borehole or casing wall; and users' attitude and proper understanding of how to install and apply a wire-type extensometer. Here experience plays a big role. Over the years, many have learned the hard way that untensioned rod extensometers are simple and inherently inexpensive, but limited to vertical up holes where sensitivity is not influenced by friction between the rod elements and the borehole wall or protective conduit, the inertia of the rod elements, or the direction of the movement to be measured. In deep, horizontal, or inclined holes, and in instances where compressive as well as tensile strains or displacements are anticipated, tensioned rod or wire systems are preferred. System Components Borehole extensometers are made up of at least the following five principal components: the instrument head; the collar anchor assembly; the downhole system of anchors and rods or wires; the signal cable if the head is equipped for electronic readout; and the readout apparatus, whether mechanical or electronic. These components are shown in Fig. 1. Borehole Requirements Most extensometers are designed for installation in nominal 75 to 57-mm (3.0 to 2.25-in.) diam drill holes. Either a diamond drill or a percussion drill hole is satisfactory, provided the variation in drill-hole diameter is within the tolerance of the standard anchor design. The basic system may be modified for other hole diameters by changing the dimensions of the collar anchor and downhole anchor assemblies. Some instrument heads and collar anchor assemblies require enlarged borehole collars, though usually not over 150 mm (6 in.) for a depth of 1 m (3 ft). It is desirable, although not essential, that holes be free-draining. Holes must be clean and free of debris before installation. Depth/Orientation of Extensometer Boreholes Extensometers are designed to measure axial strain components in the instrumented drill hole. As the drill hole is axially deformed, the distances between individual downhole anchors and the instrument head change, as do the distances between adjacent anchors. The distance changes measured by a multiple position borehole extensometer, for example, are reduced to functions of time, hole depth, anchor position, or other parameters of significance in terms of the structure under investigation.

Jan 1, 1982

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The reliable quality assessment of grouting operations is one of the key issues in establishing impermeable grout curtains around shafts, drifts and tunnels. Reliable opera¬tional information on the decrease in the permeability of rock during the grouting process facilitates the assessment of the effectiveness of the completed curtain and assures production quality. Quality control and assurance also fa¬cilitates the early detection and elimination of possible de¬fects in the grout curtain. Thorough control of the grouting process provides the capability to evaluate decreases in the permeability of water-producing fracture zones prior to the beginning or the continuation of excavation of the shaft, tunnel or drift. In order to achieve this objective, post¬grouting hydrodynamic investigations are conducted prior to the initiation or re-initiation of work on the underground workings to measure the decrease in the permeability coef¬ficient of aquifers during grouting operations. 8.1 QUALITY ASSURANCE AND CONTROL OF THE ISOLATION OF ROCK BY GROUTING THROUGH HOLES DRILLED FROM THE SURFACE Quality assurance and control are based on measuring the decrease in the permeability coefficient of water-pro¬ducing horizons as a result of injecting grout into the drill¬holes. For this purpose, the value of the acceptable residual permeability coefficient is calculated beforehand based on the acceptable value of ground water inflow into the shaft, drift or tunnel as specified by the "construction norm and integrated practice (SNIP)" (Anon., 1976). Having ob¬tained the values of aquifer thickness, permeability, and head distribution for each aquifer from flowmetric data (dis¬cussed in Chapter 3), the average value of the permeability coefficient of all aquifers intersected by the shaft is calcu¬lated as [ ] where Ki is the permeability coefficient of the "ith" aqui¬fer; Pi is the pressure of the "ith" aquifer; and M; is the thickness of the "ith" aquifer. The total expected inflow of ground water into the shaft is [ ] where RK is the radius of the contour of influence; RCFB is the radius of the shaft; and p is the coefficient of dynamic viscosity of the ground water. The necessary reduction of the coefficient of permeabil¬ity of the aquifer [ ] where Q is the expected inflow of ground water into the shaft from eq. 8.2; Q.-fin is the acceptable inflow of ground water; and a is the safety factor. By knowing the average permeability value of the rock and the permeability reduction coefficient, it is possible to determine the value of the acceptable residual permeability coefficient for all the aquifers [ ] The values of the permeability coefficient, pressure, and thickness for each aquifer are determined from the data gathered during the hydrodynamic investigations conducted in grout holes prior to beginning the grouting operations as discussed in Chapter 3. After injecting the grout into the first of the holes, the injection into each of the following grout holes is preceded by repeated hydrodynamic investi¬gations. Using the data obtained for each water-producing zone, a graph is constructed where the numbers representing the grout holes in their order of grouting are placed on the abscissa, and the values of the aquifer permeability coeffi¬cient are placed on the ordinate (Fig. 103). This curve char¬acterizes the change in permeability of the given hydro¬stratigraphic unit as grouting operations are completed, one hole at a time. The results of grouting operations are considered to be positive when each sequential observation records a steady decrease in the permeability of the aquifer. The permeabil¬ity measured prior to the injection of the grout into the last hole must be lower than or equal to the acceptable perme¬ability as determined by the application of eqs. 8.1 through 8.4. Table 8.1 presents illustrative data on the hydrogeo¬logic properties of aquifers at a mine shaft prior to the initiation of grouting operations. Data also are presented on the reduction in the permeability coefficient during the in¬jection of the grout. The shaft in question intersects eleven aquifers. Based on data concerning aquifer pressure, thick¬ness, permeability, and the expected inflow rate of water for each of the strata, the average permeability coefficient is calculated according to eq. 8.1 as K = 0.2 x 10-12 m2. The

Jan 1, 1993

By Priscilla P. Nelson, Francis L. C. Fong

Introduction Fracture mechanics is the study of the behavior of cracks and their modes of propagation. During cracking, energy is consumed in creating new surface area. The more energy a material absorbs, the higher is its fracture resistance. This fracture energy is provided either by work done externally, by the release of elastic strain energy within the cracked body, or by a combination of these two effects. Fracture resistance is measured in terms of either the stress intensity factor, K, or the energy release rate (also referred to as crack driving force), G. For linearly elastic materials, these two quantities are related by the following equation: [ ] where [u] is Poisson's ratio and E is the modulus of elasticity. Both K and G are direct functions of the applied force and the crack length. The process of rock cutting with full-face tunnel boring machines (TBMs) involves the indentation of a rock surface by rolling disc tools. Excavation occurs as fractures, extending from the locus of chip indentation, propagate between concentric disc grooves and liberate rock chips from the intact rock face. Since disc cutting is achieved by a fracture process, it is logical to anticipate that differences in cuttability of a variety of rocks should be related to the variation of fracture material properties among the rocks. Such a relation has been demonstrated between the performance of full-face TBMs and the critical crack driving force for excavation in relatively high strength, brittle, low porosity, isotropic rock (Nelson et al., 1985). The objective of this paper is to report on the results of a continued investigation of the relationship between fracture material properties and the effectiveness of disc cutting. Additional reliable data on full-face TBM performance is difficult to obtain, so that the results of disc linear cutter tests performed by the Transport and Road Research Laboratory (TRRL) (U.K.) are utilized in this study. Fracture Material Property Evaluation If a crack tip is subjected to a perfectly plain strain condition, many materials will behave in a brittle manner, and the material resistance to fracture is constant during crack growth. This resistance is referred to as the plain strain fracture toughness, believed to be a material property. The standard testing procedure for this parameter is given in the American Society for Testing and Materials (ASTM) test designation E399. To ensure plain strain conditions, acceptable specimen geometries are specified. Unless these geometric specifications are adhered to, the measured fracture resistance is regarded as the apparent fracture toughness, and a subscript Q is used, as [ ]. The methodology adopted by ASTM E399 is within the framework of Linear Elastic Fracture Mechanics (LEFM). This approach assumes that material resistance against cracking is developed instantaneously, without initial stable or subcritical crack extension. Prior to crack advancement in rock, however, much of the crack driving energy is absorbed in a localized volume in front of the crack tip, referred to as the plasticity or microcracking zone. This capability for energy absorption substantially increases material resistance, and a crack may be arrested unless an increased crack driving force is applied. The LEFM or plain strain assumptions would underestimate the actual fracture resistance of such a material. Such a conservative approximation may be desirable in the design of structures against fatigue or brittle failure. In mining or tunneling, however, an underestimation of crack resistance can lead to the selection of underrated excavation equipment and a decrease in production efficiency. The development of fracture resistance in rock is best described by the material resistance curve, or R-curve, which is a plot of fracture resistance as a function of crack extension. Typically, peak resistance is only reached after a finite amount of subcritical crack growth. The

Jan 1, 1986

By R. F. Holub, E. Franco, T. B. Borak, K. J. Schiager

INTRODUCTION According to a recent analysis by Schiager et al.(1981), inhalation of radon daughters continues to contribute the largest risk from exposure to radioactive materials in underground uranium mines. The American National Standards Institute (1973) has published a concensus standard for radiation protection in uranium mines. According to this standard, a monitoring system for radon daughters must be capable of measuring the annual accumulated exposure in working level months within an uncertainty interval of 50% at the 95% confidence level. To satisfy this criterion, uranium mining companies in the USA have adopted a procedure consisting of single or periodic measurements of the air concentration of radon daughters. All of the measurement methods sample a known volume of air through a filter. After a specified delay interval, the filter is analyzed for radioactivity. The exposure rate from total airborne potential alpha energy in units of working level (WL) is estimated from the measured activity on the filter. For control purposes, this measurement establishes whether or not a work area is safe for occupancy by miners. For routine dosimetry, the concentration estimated from the grab sample is assigned to the appropriate work area. It is then assumed that the concentration of radon progeny is equal to the average of the two measurements at the beginning and end of the specified interval. Meanwhile, the work locations and exposure times of each miner are recorded on the daily time card and verified by the shift supervisor. Most cards provide space for 15-minute time intervals. The exposure in working-level hours (WL-hr) for each shift is obtained by summing the time spent in a given location multiplied by the exposure rate (WL) assigned to that location.The exposure of an individual miner to radon progeny is summarized on a weekly basis and commonly reviewed each month. These values are then accumulated in units of working level- months (WLM) during the calendar year. EVALUATION TECHNIQUE AND RESULTS The evaluation of grab sampling methods for monitoring exposure to radon progeny is presented in two sections. The first section examines each method individually according to accuracy, precision, and uncertainties attributed to human errors. The second section includes an analysis of procedures which are common to all measurement methods. The ultimate goal is to determine whether a specific measurement method, or grab sampling in general, can fulfill the criterion that the annual accumulated exposure of each miner be known to within ± 50% at the 95% confidence level. In addition it is essential that the above criterion be satisfied at an acceptable cost to the mining company. The results of each testing procedure are presented in terms of the contribution of the relative uncertainty in the estimates of cumulative WLM. Each of these are then combined to form a figure of merit for the complete monitoring system. The method of combining statistical uncertainties and interpretation of the results is subject to some debate. However, since all of the tested parameters enter into the final computation of WLM multiplicatively, we have used the commonly accepted procedure of combining the squares of the relative uncertainties. We have also assumed that each of the uncertainties is derived from independent random variables and the covariance of any two variables is zero. A description of each grab sampling measuring method is given in Table 1. Also included is the equation used to compute WL from the measured quantities. Accuracy (U A) Our definition of accuracy is based on the uncertainty inherent in any method which attempts to estimate potential alpha energy without unambiguously determining the concentration of the three unknown radioisotopes, RaA, RaB and RaC. (For simplicity, the RaC and RaC' nuclides are referred to in combination as RaC.) The inherent uncertainty strongly depends on the mixture of these three components at the time of measurement.

Jan 1, 1981

By Wolfgang R. Wawersik, Charles M. Stone

INTRODUCTION Hydraulic fracturing was applied in horizontal drill- holes in the Salado salt formation near Carlsbad, New Mexico. Tests were performed approximately 650 m be- low surface to validate the design of a Waste Isolation Pilot Plant (WIPP) for the disposal of radioactive waste from defense activities of the United States. Hydraulic fracturing was performed primarily to determine whether the virgin in situ stress state at the WIPP site is isotropic and whether the magnitude of the virgin in situ stresses corresponds to the weight of the overburden. Beyond these limited objectives, however, measurements are now being reviewed to evaluate the usefulness of hydraulic fracturing in salt formations in general. Such measurements are desirable to determine stresses induced by mining and to monitor time-dependent stress changes around underground excavations in salt masses. Hydraulic fracturing was chosen because it is the only technique that can be readily applied in virgin ground far from existing mine openings. The method also appeared to yield directly the magnitude of the least compressive principal stress, regardless of the mechanical properties of the rock mass. A knowledge of the least principal compression was deemed sufficient to establish the isotropic character of the virgin in situ stress field under two conditions: (1) the Salado formation was mechanically isotropic, i.e., the fracture toughness did not vary normal and parallel to bedding so as to permit preferred fracture paths, and (2) pressure measurements were combined with determinations of the orientations of hydraulic fractures and, more generally, with observations of the characteristic hydraulic fracture patterns. The latter was possible by locating the drillholes for hydraulic fracturing along the axes of drifts that were mined several months later. The success of general stress measurements by hy- draulic fracturing of salt subjected to anisotropic stress conditions was and remains less certain. While the smallest in situ compressive stresses should still be equal to instantaneous shut-in pressures, there may not exist any unique relationships between the greatest and intermediate in situ principal stresses on one hand and the primary breakdown and fracture reopening pressures on the other. This problem would be a consequence of stress relaxation due to salt creep around any drillhole in which hydraulic fracturing tests are conducted. Moreover, lab- oratory measurements suggest that creep and stress relaxation could be so rapid that it might not be possible to interpret the measurements for anisotropic stress conditions even if hydraulic fracturing were performed as soon after drilling as possible. The primary objectives of the stress measurements in the WIPP were met by combining hydraulic fracturing tests with finite element analyses of the effects of salt creep, observations of hydraulically induced fracture pat- terns, and laboratory hydraulic fracturing tests on oriented core. In situ hydraulic fracturing tests in long drillholes were preceded by several trial tests to establish the best test methods and to demonstrate that salt could be fractured. The resolution of anisotropic stresses and special problems, e.g., in the identification of instantaneous shut-in pressures, are currently being addressed in hydraulic fracturing tests in a mine pillar, in tests following different delays between drilling and fracturing, and in tests with different frac fluids. This paper will review the main results of the analyses above and of one group of hydraulic fracturing tests at different distances from existing excavations. The paper will conclude with a brief description of the geometry of the hydraulically induced fracture patterns. Because of space limitations, it will be assumed that the reader is familiar with hydraulic fracturing or will first consult other sources (e.g., Cleary, 1980; Gronseth and Detournay, 1979; Zoback and Haimson, 1983; Nemat-Nasser et al., 1983; Kim et al., 1984)

Jan 1, 1986

By Mark L. Blanford, Roger M. Zimmerman

INTRODUCTION Volcanic tuffs on and adjacent to the Nevada Test Site (NTS) are being considered by the Department of Energy (DOE) for the possible geo- logic disposal of high-level radioactive wastes. The Nevada Nuclear Waste Storage Investigations (NNWSI) project was established in 1977 to evaluate such disposal. Sandia National Laboratories (SNL), one of the participants in the NNWSI project, has as one of its responsibilities the development of a rock mechanics program for the Nevada site. SNL conducted three small-diameter heater experiments in welded and nonwelded tuffs in G-Tunnel on the NTS, to investigate the thermal (heat transfer) and hydrothermal (thermal- induced water migration) behavior as part of the rock mechanics program. These two aspects were investigated to increase knowledge about the behavior of tuff so that predictive capabilities are available for use by repository designers, waste-package designers, and performance analysts. Also, knowledge of the behavior of the tuff is invaluable for planning and designing future in situ experiments at Yucca Mountain, the candidate site for the repository. The evaluations of these three experiments is the subject of this paper. Designers, analysts, and experimenters are seeking a better understanding of the behavior of tuffs under the influence of thermal loads expected from radioactive-waste storage, because of two physical features peculiar to tuffs. First, tuffs are inherently porous because of the manner in which they are deposited (Smith, 1960). Tuffs utilized in G-Tunnel testing have porosities ranging from 15 to 46%, which cover the ranges of expected porosities in the target horizon at Yucca Mountain. It has been established that the G-Tunnel tuffs have similar bulk, thermal, and mechanical material properties to those at Yucca Mountain (Zimmerman et al., 1984), thus, G-Tunnel testing can be used to evaluate the effects of porosity on the thermal and mechanical behavior. The second feature is that tuffs above the water table contain pore water that influences the thermal properties of the rock; displacement of the water must be accounted for in repository designs and analyses. For example, G-Tunnel tuffs, located some 600 m above the static water level, have saturations in excess of 60%. Similar percentages are expected at the target horizon in Yucca Mountain (Zimmerman et al., 1984). The presence of and the removal of the pore water affects the thermal behavior of the tuffs, and these three experiments were designed first to determine the phenomenological behavior and then assess influences on predictive capabilities. The focus in this paper is to present the results and evaluations of the experiments as they apply to improving predictive capabilities. The thermal aspects are emphasized by comparing the measured temperatures (in and around heater emplacement holes) with calculations of predicted temperatures using numerical models, so that the effects of significant parameters can be evaluated and integrated into future predictive models. Observation of the hydrothermal aspects is needed to assess the effects of loss of pore water and subsequent migrations on the temperature fields during the heating, and also to define the expected environment in the vicinity of the outer metallic surface around the waste. The metallic boundary can be either the outer shell of the waste package system, which is the main engineered barrier for waste containment, or the borehole liner. A final decision has not been made as yet about the necessity for lining boreholes; thus, the emphasis is on predicting the characteristics of the environment around the outer metallic surface. Two aspects that limit the scope of this paper are (1) the experiments were performed at a smaller than canister scale for the purpose of

Jan 1, 1986

By M. E. Rossi

Reconciliation of long-term, block-model reserves and mine production frequently shows significant discrepancies. This reconciliation can be done comparing the long-term, block-model reserves against a grade control model (a model based on blast holes or production data). In this article, this is called an Fl factor for tonnages, grade and ounces. This reconciliation should also be done by comparing the grade control model to the mill feed (or loaded to heaps) tonnages, grades and ounces (F2 factor). The long-term model usually contains blocks with dimensions larger than the size of the selective mining unit (SMU) of the operation. The smoothing effect of an estimator, such as kriging, will generally result in a grade-tonnage curve that does not match the grade-tonnage curve of the SMUs to be recovered. This problem is partly to blame for the reconciliation discrepancies found. In addition, in-pit perfect selection is impossible. Therefore, the grade-tonnage predictions based on blastholes also need to be assessed - considering unplanned dilution and the errors of estimation of the grade control model. This article focuses on using conditional simulations to assess the uncertainty of the predicted grade-tonnage curve in terms of minable reserves and in the framework of long-term mine planning. Quantifying the uncertainty in no uncertain terms is done in conjunction with a popular pit optimizer. It yields several possible minable reserves and several possible minable tonnages and grades, per pit shell or scheduled phase. This is a step further from the usual sensitivity analyses that are performed for deposit evaluation or development planning. Specifically, this approach takes into account the volume-variance relationship, the selectivity of the mining operation and the planned and unplanned dilution. It also carries the local uncertainty implicit in grade estimation into the mine design and mine planning phases. The estimation of recoverable reserves revolves around estimating the block distribution of metal grades from the drill hole information available, typically composites of a fixed length. Ideally, this estimation should accurately predict the ore sent to the processing facilities of an operation. Here are some definitions used in this article: ? Recoverable reserves are those where an attempt has been made to estimate the actual distribution of grades (usually by a block model) that would be found in the ground at the time of mining, relative to the mine equipment size and other operational characteristics of the mine SMU. In particular, it incorporates the effect of internal dilution for each block how the grade distribution changes in variability when comparing a composite grade distribution to the "mining unit" grade distribution. In geostatistical jargon, this is known as "change of support effect," or volume-variance effect. ? Minable reserves are those recoverable reserves defined by a mine plan. In an open-pit scenario, they would incorporate pit optimization in addition to the sequencing and scheduling of production through mine life. ? All other block model estimates from drill hole data that do not explicitly attempt to estimate or measure the volume-variance effect are called in situ. It can be argued that these models may be inappropriate tools for predicting the grade-tonnage curve of the material to be sent for processing (minable reserves). The purpose of estimating recoverable reserves can be thought of as estimating the appropriate amount of dilution that should be incorporated into the model so that it adequately predicts (long-term and on average) the grade-tonnage curve of the ore sent to the processing facilities (mean grades and ton-

Jan 1, 1999

By R. Kneisley, D. Conover, K. Haramy, K. Hanna

INTRODUCTION Coal mine entry intersections are high-risk areas for roof falls due to inherently wide roof spans, excessive stress, and variable intersection shapes resulting from breakthrough misalignments. Statistics from underground coal mines reveal that a high percentage of injuries occurs from roof and rib falls in entry intersections (Peng, 1980). The U.S. Department of the Interior, Bureau of Mines, is conducting a field research project to investigate failure modes surrounding underground coal mine entry intersections. The research objectives are to (1) develop a method to determine failure modes and stress-displacement relations around coal mine intersections and (2) develop engineering guidelines and empirical relationships for use in designing safer coal mine entry intersections. The basic approach to achieve the objectives is to instrument and monitor intersections before, during, and after intersection development in order to determine contributing parameters, such as in situ stresses, stress changes, strata movement, geology, physical properties, and mining sequence, that may influence the short- and long-term stability of the intersection and adjacent entries. This paper describes a rock mechanics instrumentation program, data analyses, and a comparison of two case studies conducted at two underground mines, designated as "A" and "B", in the Illinois Coal Basin. The instrumentation plans and data collected during development and long-term monitoring of four-way intersections and adjoining entries are presented. Data analyses of pre- and post-mining roof stress, pillar loading, strata movement, roof bolt loading, and geologic features are included. INTERSECTION FAILURE MECHANISM The region surrounding an entry intersection is characterized by different failure criteria than the region surrounding a single entry. Stresses induced during intersection development may result in a high incidence of roof and rib failures. Various numerical modeling techniques have been used to evaluate the failure modes surrounding intersections (Gercek, 1982; Chugh et al., 1975). Numerical modeling techniques include problems associated with the analysis of post-failure behavior, provision for different horizontal stresses (i.e., 01 f 021, and determination of inputs required for any non-elastic behavior. It seems likely that more sophisticated failure criteria, based on actual field data, are needed. The Bureau of Mines has conducted an extensive instrumentation program to investigate actual intersection failure mechanisms and to provide an improved understanding of stresses and deflections using beam and plate theories. Beam theory is not applicable to analyzing intersections (Wright et al., 1964); however, it can be used to explain roof deflection and failure (shear and flexure) of adjacent entries and to provide an improved understanding of stress changes and displacements as the entries, crosscuts, and intersection are developed (Hanna et al., 1985). Beam theory may be used for entries when the roof length is twice the width. When the length is less than twice the width (as in intersections), the roof must be analyzed as a three-dimensional problem, and stress and deflection calculations are based on flat plate theory (Adler and Sun, 1976). The confined-core theory (Wilson, 1972) hypothesizes that within a typical pillar, two regions exist: a confined-core region where the horizontal confining pressure is uniform and approximately equal to the overburden pressure, and a yield zone where the vertical pressure increases from nearly zero at the rib to a pressure peak at the boundary of the yield zone. The strength of coal in the yield zone ranges from nearly zero at the rib to nearly full strength at the confined core. The vertical stress in the confined core decreases from maximum at the yield zone boundary to the overburden pressure some distance into the pillar. Excavation of the adjoining entries

Jan 1, 1986

By J. M. Dean, R. L. Grayson

Introduction With the continued downward pressure on coal selling prices, mine management must make its operations as efficient as possible. The problem is the same one throughout the mineral industries, streamlining operations to maintain competitive min¬ing costs (Born, 1991). There has been a great deal of research into better using production manpower. But the story is different for operations support personnel. Traditionally, planning man¬power requirements are done annually, with modifications to the operating plan occurring generally quarterly. On the other hand, the demands on manpower are often dynamic, being responsive to changing productivity levels, mine conditions (including water influx, bad roof, poor floor) and unanticipated project requirements (responses to machine breakdowns or a new section setup requirement because of a drop in coal quality in another area). Such changes may impact the manpower structure significantly. At times they may cause serious labor relations problems concurrently. Realignments and the generation of instability in the workforce because of active job switching (bidding) are a result. Most responses by coal operators are reactive rather than proactive, a situation that could be mollified by more accu¬rate and detailed planning of predictable manpower require¬ments. A manpower planning tool is needed that takes into consideration such things as changing productivity levels and conditions as manhour requirements for different work areas are planned, rather than blindly allocated through traditional staffing modes. Mine Management Support System The Mine Management Support System (MMSS) is an integrated decision support system that was developed using Sun Microsystems hardware according to the contract be¬tween the US Bureau of Mines and West Virginia University. The software used in the development of MMSS included X¬ windows (Scheitler and Gettys, 1986) for the user interfaces, LASER (Raman, 1985; Hayhurst, 1990) for the expert sys¬tem and graphics components, and the C language for general programming requirements. Sun DOS was used to allow the use of IBM-compatible applications software on the Sun networks. Sun OS is the operating system. It can be viewed as an enhanced version of UNIX. One of the components of MMSS that was developed to address the many specific objectives outlined in Grayson et al. (1990) is the work scheduling system. MMSS accom¬plishes work scheduling by using a mathematical (goal) programming approach to minimize the amount of switching of workers from their regular jobs to perform other jobs (Grayson and Nutter, 1991). Manpower support program The main objective of MANSUPP is to plan a detailed manpower structure for a mine by incorporating a production schedule, condition-modified work standards and manage¬ment preferences to predict required manhours for various support activities, for example, belt moves. This is accom¬plished by gathering and processing planning information the same way a mine planner would. The program is menu¬driven with the selection of a particular menu item locating the user in the appropriate area within the spreadsheet to review/add information. All of the interactions between productivity, section conditions and management prefer¬ences and their effect on the amount of support work required must be considered. Information regarding the productivity of a particular section, the geometry of the section, work standards for individual activities and section conditions must all be gath¬ered for input into the program. In the initial stages of development, it was decided that the program be developed in an environment that mine planners were familiar with in order to accommodate the use of the program. Lotus 1-2-3 or a compatible (Quattro Pro) met this environmental need. Other reasons included ease of calculation due to built-in functions, powerful command language and macro capabili¬ties. Each of the major components of the program defined are summarized. Production schedule This area allows the user to input a production schedule for the entire mine over 12 periods. Space has been provided for five sections, advance or retreat, and two longwall sections. There are several calculations occurring in this area that do not apply to the determination of manpower, but serve as an aid in production planning. Section description The section description area of the spreadsheet is shown in Table 1. The first three items are calculated in the production schedule area of the worksheet and then transferred to this location. The remaining information is input by the user to be used in later calculations.

Jan 1, 1996