Search Documents

By B. Pollack, L. G. Stevens

INTRODUCTION In other chapters of this volume many of the important technical aspects in the design of concentration and dewatering circuits have been discussed. This chapter will deal with the steps necessary to bring that information together in order to produce the specifications necessary to purchase the equipment and complete the design. It deals with the plant as a whole rather than just concentration and dewatering, since the steps are essentially the same. Prerequisites to Engineering Design Feasibility studies will have been completed and design parameters established prior to the start of the engineering design stages for a metallurgical plant. The data base for the feasibility studies will have included laboratory and/or pilot plant test work, historical data, proposed plant site data such as climatology, topographic mapping, geological and geotechnical information. These studies will have established the general project design criteria as well as the process design criteria leading to the preparation of preliminary flowsheet ( s) and/or alternative process flowsheets. These will have incorporated metallurgical and material balances, allowing identification of major equipment items, and development of preliminary plant site plot plans. Preliminary technical and economic assessments and recommendations will have been prepared during this phase for Owner's review and evaluation of the technical, physical, and cost effectiveness of the overall project and its component process, process facilities, and supporting facilities elements. After Ownert s approval and decision to proceed, the engineering design can be initiated, using the above information as the basis. Engineering Design Phase The engineering design of metallurgical plants and their elements are generally developed in two sequential stages, namely: (1) Basic ("Front end") Engineering Design (2) Detail Engineering Design Figure 1 relates these engineering stages to the entire program from feasibility through construction.

Jan 1, 1986

By R. V. Ramani, R. Bhaskar

The results of an experimental and theoretical research study into the spatial and temporal behavior of dust in mine airways is summarized. Experiments were performed in mine airways under both controlled and normal operating conditions. The controlled experiments included the documentation of the concentration and deposition patterns for two types of dust under three different velocities. Real-time dust concentration data were obtained using real-time aero- sol monitors (RAM-I) to determine the dispersion coefficient in a mine airway. On the theoretical font, a convection diffusion model of the dust flow phenomenon in mine airways was developed considering dominant mechanisms affecting dust transport and deposition in mine airways. Mechanisms modeled include turbulent and gravitational deposition, coagulation, and dispersion. In this paper, comparative analyses of results (8 the controlled experiments with the predictions of the mathematical model are presented. In addition to the overall validity, the adequacy of the individual components of the model, such as deposition in the total and respirable range, and dispersion are examined in light of the experimental observations. The experimental data from controlled experiments compared more favorably with model predicted results for similar conditions as opposed to the comparative analysis results for in-mine experiments. Specifically, the model predictions for an 800-m stretch of a mine airway reveal some significant differences from the behavior noticed in the mine. The deposition was lower than that predicted by the model. Consequently, concentrations were higher than those predicted by the model. The implications of these and other findings for further investigations are discussed in the paper.

Jan 1, 1987

By J. V. Calara, J. D. Miller

The sign of the surface potential for complex non-reactive ionic solids cannot be predicted solely from consideration of the hydration energy of gaseous ions which constitute the ionic lattice. Accurate analysis of these systems must involve the hydration energy of surface ions, which requires knowledge of the crystal structure, the identification of cleavage planes, and the calculation of binding energies of surface ions. Surface binding energies for ionic solids can be deter- mined if the Surface Madelung Constant is known. A computational technique was developed for the calculation of Madelung Constants for infinite lattices which gives excellent agreement with the values calculated by other more complicated methods reported in the literature. Extension of this technique permits the calculation of Surface Madelung Constants and binding energies of surface ions, ?Us, for semi-infinite solids. The hydration free energy of gaseous Ions, ?Fh, together with the calculated binding energy of surface ions, ?Us, allows calculation of the hydration energy of surface ions, ?Gh, as for the case of the ionic solid, MX:

Jan 1, 1976

By Pentti Seppanen

The activities of Outokumpu Oy in the mining industry span all branches from prospecting to the production of refined metals and the manufacture of semifinished products. Products include copper, zinc, mercury, cadmium, nickel, cobalt, sulfur, gold, silver, iron ore, stainless steel, selenium, ferrochromium, lead and chromium concentrates, as well as chromite foundry sand. In addition, the activities of Outokumpu Oy extend to development and production of instruments, planning of industrial projects and instrumentation as well as the manufacture of specialized machines for ore concentration. The company now operates ten mines, eight of which are underground and all of which are in sulfide deposits except one. The fully automated monitoring and control of underground mine ventilation at the Pyhasalmi mine are an important technological contribution to the industry. Development work on the ventilation control was started in 1969, and since May 1973 it has operated in a fully automated computer-controlled mode. The Pyhasalmi mine has been in production since 1962, having begun as an open-pit operation. Development of underground mining began in 1967. The present annual production is one million tons all from underground mining. The underground mine is equipped with a main shaft and an auxiliary shaft, and two raises for ventilation. There is also a rampway from the surface to a depth of 500 m. The main shaft is for ore hoisting and the auxiliary shaft is used for waste-rock hoisting and for downcast ventilation. One of the raises is for downcast ventilation and the other is for upcast ventilation. The mining methods employed at Pyhasalmi are sublevel stoping with backfill, sublevel caving, and sublevel shrinkage stoping. Copper and zinc concentrates are produced. The Pyhasalmi mine is highly mechanized with about 4000 installed diesel horsepower underground. The maximum capacity of fresh air is 150 m3/s.

Jan 1, 1979

By Wayne W. Murdy

Since 1993, Newmont Mining has been growing through the development 'q of three major foreign mining operations with a fourth under construction. The first project, Yanacocha in Peru, began operating in October 1993. This occurred at a time when political and business risk in that country was considered high. In 1995, Newmont began operating the Muruntau joint venture in Uzbekistan. It is the first mining project of its kind in the Confederation of Independent States (CIS). In early 1996, Newmont started operating the Minahasa Mine in Indonesia. In early 1997, Newmont began construction of a $1.9-billion project in Indonesia. The company is also completing a feasibility study with its partner for the development of a gold operation in Mexico. All of these projects have been considered "risky" by most standards. Newmont has been successful in all of them through risk mitigation programs. These programs include using strong and successful in-country partners, concentrating on developing a strong national workforce with minimal expatriate employees, using World Bank, European Bank for Reconstruction and Development (EBRD) and International Finance Corp. (IFC) financing and building and maintaining strong ties with host governments.

Jan 1, 1997

By Faruk Oksuz, Cary Hirner, Ray Brainard

"Key project participants, including owners, engineers, and contractors continually seek for sound and structured decision analysis on how to select the best contracting method for successful project delivery. In addition to being burdened with technical challenges, lack of resources, budget shortcomings, regulatory requirements, and bureaucratic and politically mandated obstacles, the project participants need a reliable decision analysis model on the best project delivery method. The pendulum of choice for contracting continually swings back and forth between traditional design-bid-build and alternative delivery options such as design-build, progressive design-build, construction manager at risk, and public-private-partnership. For large tunnel projects, the decision process is further complicated due to contract packaging options as well as risks in underground construction. Contracting strategies for large tunnels require thorough consideration of performance, risk, quality, operability, cost and schedule. This paper compiles an array of decision making criteria and tools for an unbiased and balanced evaluation and ranking system in the procurement of large tunneling projects. INTRODUCTION Successful project delivery hinges upon meeting the owners’ expectations and key performance indicators. Large tunneling programs benefit from a thorough understanding and successful implementation of project delivery options by key project participants including the owners, engineers and contractors. The key to success is a collaborative advancement of project as the key project participants knowledgably address the applicable management, performance, risk, quality, cost, operability and schedule considerations throughout a project realization cycle. PROJECT REALIZATION CYCLE All projects have customary planning, design, construction, commissioning and operation phases that may seem to be sequential but in reality that are well integrated and dependent on one another. A glitch in any phase of a project realization cycle could hinder a successful outcome and none of the project partners are immune to consequences whenever and wherever they may surface."

Jan 1, 2016

By Thierry Coléou

In this paper, we consider open pit optimization. At present, most methods specify the economic parameters and then find the corresponding optimal pit. But as the economic environment varies (which it does regularly these days), the "optimal" pit changes and quite often changes markedly. The questions are: by how much does it change and which parameters are most influential? The functional approach of Technical Parameterization of Reserves, devised by Matheron in 1975, gives the set of all the different optimal pits, under any economic condition. It separates technical design and economic assumptions and thus permits the use of several optimality criteria when choosing the final pit, and not just the maximization of an additive profit formula. Very efficient specific algorithms are presented to obtain all the potentially optimal pits. Fluctuations in the parameters induce changes in the optimum design. Inclusion relations that exist generate very tight bounds and hence very quickly detect optima, even when using a classical adaptation of maximization techniques (graph theory, moving cone, dynamic programming ...). The advantage of Technical Parameterization of Reserves over other methods is that it provides a nested sequence of optimal pits which can then be used for mine scheduling. Many possible mining schedules can be obtained by using the family of technically optimal projects to split up the orebody. The "optimal" schedule, which is in fact a compromise between the different requirements of the economists, the mine planner and the metallurgist, can be chosen from within the wide scope of possibilities. A practical example of mine scheduling for a chromite mine is presented in detail.

Jan 1, 1989

By H. M. Wells

The known high grade mineral re- sources in the United States are fast becoming exhausted; viable new deposits are more difficult to find and more expensive to develop; operating and capital costs have increased to meet more stringent regulatory standards. By contrast, international producers enjoy a cost advantage as a result of higher mining grades, improving technological competence, and more favorable government support. The domestic base minerals industry is finding it more and more difficult to compete in world markets. It has become essentially a marginal industry today. The current philosophy of taxation in the United States has evolved over the past century. The structure of the taxing system is based on the assumption that a firm must be able to pay its tax imposts out of profits. In principle, firms incapable of supporting the tax load should be replaced by others that can do so. This philosophy applies equally well to the mining industry, so long as it remains economically healthy. However, mineral resources are finite. The situation in the domestic base mineral industry has changed fundamentally in recent times. For the reasons given above, much of the industry now cannot continue to compete profitably in the open world market; and there are no known alternative domes- tic mineral resources more capable of doing so. Under these circumstances it is important to consider the effect of taxation not only on profitability, but also on survivability.

Jan 1, 1986

By George F. Klernrnick

The Pokorny sulfur deposit is located in the northwest comer of the Delaware basin in the Rustler Springs sulfur district of west Texas. To date, 57 sulfur test wells have been drilled by Addwest Minerals delineating a resource of greater than one million long tons (It) of native sulfur. The deposit, hosted by the Permian Ochoan Castile Formation evaporite sequence, is a sulfur-bearing bioepigenetic limestone replacement of banded bituminous anhydrite. Three distinct mineralized horizons are present that correlate with zones of halite dissolution in the Castile. Sulfur mineralization occurs as hydrocarbon-poor disseminated grains, and as crystalline linings of discontinuous planar voids and large vugs.

Jan 1, 1992

By Keith S. Liddell

Gold in many ores occurs in sulphides, which, if the gold is finely disseminated, renders the ore refractory and therefore not amenable to the simple process of milling and cyanidation. Traditional methods of treatment of these refractory ores is to produce a sulphidic flotation concentrate which is roasted to form a porous calcine from which the gold is recovered by cyanidation. The roasting process imposes a constraint of a minimum sulphur grade of the concentrate on the flotation plant, which may lead to a lower gold recovery being achieved in the flotation section. Thermal decomposition of the concentrate by roasting means that the sulphur contained therein has to be treated and disposed of in an environmentally acceptable manner; and, if arsenopyrite is present in the concentrate the environ- mental aspects will be worsened. It has long been recognized that finer milling of gold-bearing materials improves the liberation of gold, especially when the gold particles are very fine. After extensive laboratory and pilot plant investigations (Liddell, Patents), a suitable mill has been developed for the mining industry by Metprotech, which is capable of producing very fine grinds (down to 90 percent passing one m if necessary). In the course of the investigations it has been found that a large number of gold-bearing materials are amenable to fine milling. A specific advantage that fine milling of sulphidic materials has over oxidative processes such as roasting and bacterial leaching is that the sulphides are not decomposed and there is therefore not a sulphur disposal problem. Furthermore, the milled sulphides can become a future sulphur feed source, and can be reclaimed if necessary. A further feature of the Metprotech process is that it is possible to add cyanide to the mill feed

Jan 1, 1988

By V. Enns, E. Soprovich, J. H. G. Laflamme

A mineralogical and geochemical characterization study was carried out on arsenic-bearing Ketza mine tailings to complement a column extraction test program with the purpose of assessing the potential of arsenic mobilization from the tailings. Two types of tailings samples (i.e., exposed tailings from the impoundment area and water covered tailings samples) were subjected to column tests under standing water cover and with no water cover but weekly flow-through flushing. The tailings have a uniform size distribution. The samples are characterized by high Fe2O3 (44.0 to 68.2 %) and As (3.7 to 4.4w%) concentrations. Ferric hydroxides are the dominant species that are mostly amorphous or cryptocrystalline. Arsenopyrite, scorodite, an Fe-Ca arsenate hydrate phase, an Fe-Bi-As phase and ferric hydroxides are the arsenic-bearing minerals. Arsenic is essentially contained in Ca-As goethite, Fe-Ca arsenate hydrate phase and scorodite. Goethite, although containing low levels of arsenic, could be a significant arsenic-bearing phase because of its high abundance. There does not appear to be any significant chemical or mineralogical difference between the original exposed tailings and the material left underwater with no flow-through for over a year. There are differences in terms of CaO, Fe2O3, SiO,, As, goethite, scorodite, calcite and dolomite concentrations between the exposed tailings and the column material after undergoing approximately two-year flow-through and aggressive leach tests. These differences are likely to be resulting from a combination of different column test conditions and sampling or heterogeneity of the material.

Jan 1, 1998

By R. E. Johnson, J. E. Dutrizac, B. R. Palmer

Silver sulphide (acanthite) and lead sulphide (galena) dissolve relatively rapidly in FeCl3 media with the formation of elemental sulphur and soluble silver and lead chlorides. Parabolic kinetics are observed, and the leaching rates are controlled by the outward diffusion of the AgCl and PbCl2 reaction products through the constantly thickening elemental sulphur layer formed on the sulphide. Hence, both leaching rates are strongly dependent on those variables which affect the solubility of AgCl or PbCl2 at the reaction interface. The rates therefore increase with increasing temperature and total chloride ion concentration, but decrease in the presence of elevated concentrations of AgCl or PbCl2. By contrast, neither sulphide is significantly attacked by ferric sulphate media, even at high Eh values. Although the reasons for the refractory behaviour of Ag2S in sulphate media remain unknown, the low rate of PbS attack is attributable to the passivating layer of PbSO4 and elemental sulphur formed on the surface of the galena.

Jan 1, 1993

By Gene E. McClelland

4.1 INTRODUCTION Metallurgical testing is required on any ore, waste or tailing material before amenability to heap leaching treatment can be accurately determined. The amount of testing necessary to determine and optimize heap leach amenability and conditions for any feed material is determined by the ore type, grade, size of deposit, and the overall financial commitment a particular company is willing to make. It is very easy to either "under-test" or "over-test" a particular deposit or feed material. A good heap leach testing program will provide the necessary design information without "bogging" down in too much detail. The three basic stages of ore testing include: • Preliminary--bottle roll tests and small column percolation leach tests; • Detailed--larger column tests, different feed sizes, and feed size optimization; and • Pilot-Scale--Column or field heap. The following subchapters describe the stages of heap leach testing necessary to put a viable property into production. 4.2 PRELIMINARY METALLURGICAL TESTING The two types of preliminary tests that can be undertaken include bottle roll or cyanide agitation tests and small column leach tests. Each of these is described below, along with information about what the test results provide in terms of furthering knowledge of ore qualities. 4.2.1 Bottle Roll Tests The first step in a heap leach testing program is preliminary bottle roll tests at a relatively coarse feed size to determine the ore's leachability. Bottle roll tests are usually conducted on reverse circulation drill cuttings samples (= 1/4 inch (6 mm) in size). Bottle roll tests provide initial information about precious metal recovery, recovery rate, and reagent requirements. The recovery results are to be considered maximums because attrition grinding creates fines and liberates recoverable values that would not be liberated from the material during a static leach. Bottle roll tests can be conducted on up to 25 lb (11 kg) ore charges of up to two inches (50 mm) in size. However, the coarser the feed the more attrition grinding occurs during rolling.

Jan 1, 1988

By J. Linhart

In vertical airways, falling material - solids-or water - may cause undesirable disturbances in the ventilation in the airway itself and also in neig¬bouring airways unless precautions are taken to stabilize the air flow. Such cases can occur, for example, - in shaft sinking by drilling from a pilot hole, - during the filling up of shafts, and - during the introduction of water into shafts in the case of mine fires. In an airway with upward ventilation the falling material will reduce the air flow and may even re¬verse its direction. In an airway with downward ventilation the air flow can only increase, but a reversal of the direction of ventilation may result in a parallel airway. These disturbances in the normal ventilation are undesirable as it must be the aim to have ventilation that is stable in quantity and direction throughout a mine. In order to be able to prepare suitable stabilization measures one must know the pressure generated by the falling material; this pressure will henceforth be called "aeromotive" pressure. The main factors determining the influence of falling material on the ventilation are - the amount of falling material and its height of fall, - the cross sectional area of the airway, - the pressure. difference prevailing in it, - the-position of the. airway in the ventilation. network, - the air velocity, and - other parameters, e. g. the density and grain size of the falling material. To determine the aeromotive pressure-measurements have been made underground during the sinking and filling of shafts and systematic studies have been carried out during the supply of water into a staple shaft. The present paper deals first with some fundamental theoretical considerations and then describes the measuring arrangements and the results of the series of experiments that have been carried out.

Jan 1, 1980

By Y. C. Kim

For the past few years, the Cyprus Bagdad Copper Company began experiencing a significant "ore-dilution" problem from its low grade open- pit copper mine located at Bagdad, Arizona. To pinpoint the causes of this dilution, a study was initiated to investigate as well as to improve in-pit ore-waste selection-procedures using conditionally simulated ore-bodies. Prior to the actual use of conditional simulation; a comparison of different estimation methods for a mined-out area in the pit was performed. Specifically, kriging estimates were compared against the original estimates of the company which were based on the polygonal approach. The results of this comparison clearly identified part of the so- called "ore-dilution" problem, which was the initial over-estimation of average ore grades from blast rounds, using the polygonal approach. The results from the use of conditionally simulated orebodies demonstrated that the "ore-dilution" problem can be reduced by more than half if in-pit ore- waste selection is based on the kriged estimates rather than the polygonal estimates. This simulation study also showed that the current use of the polygonal approach has the effect of shipping a larger tonnage of lower grade material to the mill.

Jan 1, 1982

By Pooyan Asadollahi, Praveen Krishna, Michael Joye

"Durability design for underground structures is an increasing focus of designers and owners in the underground construction industry. Many owners have expanded their requirements for durability design, with specific requirements for structure lifecycle and designer certification of structural durability. This paper describes current trends and best practices including: defining the underground structure lifecycle, historically durable underground structures, design methods for underground structure durability built of reinforced concrete, and durability of materials. Criteria to be used for defining end of structure life and owner’s maintenance responsibilities are crucial to lifecycle contract requirements. Current practices of several major owners are presented. Design methods are presented including United States code requirements. Current best practices for enhancing the durability of materials used in underground construction are discussed including: low permeability concrete, steel reinforcement concrete cover, the use of steel fiber, and testing for verification. INTRODUCTION Durability design is increasingly being recognized as an essential component of good design practice. Infrastructure owners recognize that to serve the public interest, constructed facilities must be lasting and durable. The public understands that structures with limited service life result in increased costs and add to their daily inconvenience with frequent repair and reconstruction. Engineers are increasingly asking not only is the structure strong enough but will it last for generations. Durability design requirements are no longer just adherence to some accepted practices, but are based on analytical approaches, with results that can challenge our beliefs in what construction materials and details result in a durable structure. This paper describes current industry requirements and practices for durability design of underground structures, and offers some suggestions regarding future trends and developments. SERVICE LIFE DEFINITION The service life of a structure is the sum of the time to onset of deterioration, called initiation period (ti), and the subsequent time period of deterioration ending when the structure is no longer functional, called propagation period (tp). Figure 1 shows a conceptual service life diagram. These time periods can be substantially affected by the level of maintenance performed during the life of the structure."

Jan 1, 2016

By C. O. Brawner, A. Bellamy, D. S. Cavers

Pit slope designs at Nickel Plate Mine have used relatively steep interim and final wall slopes of 60 degrees overall. The rock is unusually strong and tough with most discontinuity sets being steeply dipping. An integrated program of monitoring and drainage has been used. Stopes of large extent which are generally unsupported occur on the property. For the most part, no deterioration of the stability of the stopes has occurred over the last 30 or more years. Mining methods through these areas have used a combination of fill s placed via VCR drop raises and crater blasting of the backs. One of the major challenges in mining through the stope areas is to maintain slope stability conditions and to reduce dilution of the higher value ore zones occurring immediately around the stope areas. The paper discusses geology, slope stability and mining methods at Nickel Plate Mine.

Jan 1, 1988

By Joseph Kurtak

When prospectors discovered mineralized outcrops in Pine Creek Canyon in 1916, little did they know the site was destined to become one of the world's greatest tungsten mines. Located outside Bishop in California's rugged Sierra Nevada mountain range, the mine's development imposed unique challenges to the hardiest of mining men. In its early years, the Pine Creek operation was plagued by bad luck and poor timing. But through the perseverance of a dynamic group of mining personalities, it would gain world class status. Pine Creek tungsten supplied much of the defense needs of the United States during World War II and put the Bishop area on the map as a major contributor to the nation's stockpile of strategic metals. The mine's history was shaped by world politics, the ups and downs of metals demand and economic survival through technological innovations. In contrast to many mines, Pine Creek's workings went horizontally into and then up inside the mountains - nearly to the ridgetops. This resulted in the name "Mine in the Sky" being attached to the operation. The origin of Pine Creek's ore bodies is related to the emplacement of a portion of the Sierra Nevada batholith about 100 million years ago. During the intrusive process, granitic magmas engulfed overlying calcareous sedimentary rocks, flooding them with silica-rich hydrothermal fluids and metamorphosing them to skarn. The fluids also contained tungsten, molybdenum and copper. They precipitated as scheelite, molybdenite and chalcopyrite, respectively, during the metamorphic process. The ore-bearing skarns occur as near-vertical tabular pendants in the intrusive rocks. These were later exposed by the uplift of the Sierra Nevada mountain range and glacial erosion.

Jan 1, 1998

By Kenneth V. Luza

Underclays are associated with coals found in eastern Oklahoma. These coals are of bituminous rank and are in beds of Middle and Late Pennsylvanian age. They occur in an area of about 8,000 mi2, within the southern part of the Western Interior Coal Region. The rocks of the area consist of a thick series of sandstones, shales, underclays, coals, and limestones. There are more than 40 beds of bituminous coal in the state, but only 12 of these have been mined over large areas. The 12 are, from oldest to youngest: the lower Hartshorne, upper Hartshorne, McAlester (Stigler), upper McAlester, Cavanal, Rowe, Secor, Weir-Pittsburg, Mineral, Croweburg, Iron Post, and Dawson coals. None of the underclay associated with these coal beds is known to have been exploited commercially. Nine samples of underclay from beneath the Croweburg coal were collected over a wide area in the eastern Oklahoma coal field for evaluation. The underclays are usually shades of gray with brown or orange iron-oxide staining. Although soft and plastic in some places, they are generally hard and slickensided, and contain abundant carbonized plant fragments. Bulk chemical analyses, clay mineral identification, and ceramic tests were performed on each underclay sample. The dominant clay minerals are illite and kaolinite with some mixed-layer clays. Silica (Si02) ranges from 45.96% to 59.03% and alumina (Al2O3) varies from 14.98% to 23.60%. The U.S. Bureau of Mines Tuscaloosa Re- search Center conducted the ceramic evaluations. Samples were slow fired from 1,000°C to 1,250°C in 50°C intervals. Bulk density, color, percent linear shrinkage, and percent absorption were determined for each slow fire test. All Croweburg underclay samples are best suited for building brick.

Jan 1, 1999

By Julius Rubinstein, Victor Badenicov

The development of column flotation is the most significant achievement in the area of mineral processing in the last few decades. The high efficiency of column flotation allows a reduction in process time, a decrease in the number of cleaner stages and in the volume of the circulating load in the flotation circuit, and, as a result of this, an increase in consistency and reliability of operations. Unique multisectional column flotation apparatuses were developed. Such designs have a number of essential advantages as compared to monocells. A change from monocells to multisectional column allows to provide favourable conditions for separation of particles of various floatability. To attain that aim particular hydrodynamics and aeration regime is established in each section of the column, operational variables being adjusted according to the floatability of the material. Therefore in multisectional column machines the material-apparatus feedback can be established, process variables optimized depending on the characteristics of the floated materials. This concept forms the basis of column designs we have developed. For the first time column cell with alternating slurry Rows (combination of co- and counter-current flows) were developed and commercialized . Successful operation was reported of the new generation of columns with cell volumes of 10 to 80 m3 and the height of 4-6 m in copper, molybdenum, antimony, tungsten and nickel ores and coal slurry processing at different plants. Operation experience of these cells showed their considerable design and operational advantages and verified the proposed options and relationships. The new apparatus is provided with a pneumohydraulic aerator allowing to control bubble size distribution, the service life of the aerator is not less than two years. A multilevel flotation model was developed and used to work out a technique of column design and process parameters calculation. A method of the apparatus design parameters calculation based on laboratory test results (scaling up) was worked out. The method is based on flotation macro and micro-hydrodynamics simulation.

Jan 1, 1995