Search Documents

By R. R. Jozefowicz, T. X. Ren, J. S. Edwards

The control of methane emission into underground mine workings is important both for the safety and productivity of the mine. As deeper and gasser coal seams are mined, ventilation methods involving increasing air pressures and quantities across mine workings may not be able to cope consistently with methane emission rates during the production cycle. An accurate prediction of methane emission into mine workings is of great significance in the design of ventilation systems and additional methane control methods if required. Research has been conducted to develop a numerical method for simulating methane flow through strata in which permeability is strongly influenced by mining-induced stress. To achieve this objective, both numerical modelling using Computational Fluid Dynamics (CFD) and laboratory tests on rock samples and granular materials under triaxial stress condition were carried out. Correlation has been established between stress and permeability characteristics of rock-measure rocks and laboratory results are being incorporated into the CFD models. This paper introduces the use of CFD techniques to model methane flow through permeable strata around longwall coal faces currently undertaken at the University of Nottingham.

Jan 1, 1997

By Robert A. Jankowski, Jonathan Kelly, Edward F. Divers

Results for the first underground test of the ventilated drum in a U.S. coal mine are presented. Tests were conducted by the Bureau of Mines through a contract research program with Foster-Miller, Inc., to evaluate dust control effectiveness in a western mine and for gas control in a full scale laboratory facility. The ventilated drum is designed to reduce the amount of dust from cutting by drawing dust-laden air from the cutting zone through twelve water- powered "dust capture" tubes built into the shell of the shearer drum. High pressure water up to 1 12.48 kg per cm2 (1,600 psig), released from sprays, induces maximum airflow of 1.89 m3/sec (4,000 cfm) from the face side of the drum and provides cleaning for respirable dust and improved methane dispersion. At the gob side of the drum a deflector plate, attached to the cowl arm, turns the water spray and a proportion of the cleaned air back into the cutting zone. More than 50 ventilated drums have been installed to date in England, and their tests carried out on fixed height and single-ended ranging drum shearers have shown reductions in respirable dust of 60-80 pct, as compared with conventional wet cutting. The U.S. test on a double drum shearer showed slightly lower reduction.

Jan 1, 1987

By H. Sevim

In long-term open pit production planning, a series of nested and maximum-value pits is usually generated first. These pits are then considered as possible pushbacks over a number of planning periods. To determine the best pushback in each planning period, the pits are evaluated for their technical and economical feasibilities under certain production constraints. Parameterization is a commonly used technique to generate a series of pits. In almost all cases, however, some of the consecutive pits generated by this technique are too far apart from each other. This is called the "gap" problem. It may make the entire pit series useless for production planning purposes. A new pit gener¬ating algorithm has been developed to overcome the gap problem. Through this algorithm, a series of nested maxi¬mum-value pits can be generated with a controllable size increment. The logic of the algorithm is illustrated through a small hypothetical case. Its capability of generating maximum-value pits that are as optimal as those generated by parameterization and its advantages over parameteriza¬tion are presented through an actual gold deposit case.

Jan 1, 1996

By Z. T. Bieniawski

Ground support requirements for safe and economical design of room and pillar coal mining layouts are reviewed. The design methods for mine roofs and mine pillars are discussed and the role of the geotechnical aspects is considered. It is shown that current support design procedures in the United States do not utilize fully the latest research findings and the need for more effective technology transfer in coal mine ground control is emphasized. Promising new developments in ground support are identified and possible research areas are suggested.

Jan 1, 1982

By Robert J. Timko, R. Lincoln Derick

This report presents a Bureau of Mines evaluation which examined the extent of gas leakage from sealed areas in underground coal mines and measured the effectiveness of commonly used structures for controlling the quantity of gas exchange from these areas. Evaluations were performed on five abandoned areas in two operating underground mines within the same coal seam. Methane and oxygen levels inby the seals were monitored to determine if the gas leakage was unidirectional or bidirectional. Results from this and prior work dealing with minimizing gas leakage were then applied to a newly abandoned area. Also discussed are bulkhead site preparation, construction plans, techniques for monitoring the status of the atmosphere within the sealed volume, and a modified European method for controlling gas migration from the sealed volume to the active mine.

Jan 1, 1991

By Gerald P. Kelton

Hydrocyclones have emerged as successful classification devices In closed circuit grinding applications However, their use for ultrafine particles separation is a relatively new application For ultrafine particles separation In small diameter (51 mm or smaller) cyclones, the cyclone diameter, feed pulp density or viscosity, pressure drop, and configuration play an important role Most often commercial application of the small diameter cyclones suffers from plugging problems resulting from the presence of fibres, wood chips, paper scraps, etc This paper describes important design features of small cyclones, followed by examples of case studies of commercial application of these cyclones

Jan 1, 1983

By J. M. Scharer, Bruce E. Halbert, Lysane Bouduc, Douglas B. Chambers, Jennifer L. Kirkaldy, Carol M. Pettit

Io contrast to acid mine drainage (AMD), neutral mine drainage (NMD) has not yet received widespread attention. Metal and sulphate concentrations can be elevated and of concern in neutral drainage from waste rock and tailings. In the present paper, metal release in high ionic strength mine drainage at neutral pH is evaluated at several mine sites. Specific factors including oxidation rates, buffering capacity, and hydrology are also addressed and their effect on the production of contaminated NMD from mine wastes is evaluated. Case studies are presented involving current seepage water quality and predictive geochemical modelling to illustrate the possible time frame and magnitude of the contamination.

Jan 1, 2000

By C. Steiakakis

Over recent years large construction projects have taken place and will be taking place in complex geological environments. In order to reduce costs and increase safety, a detailed geotechnical evaluation of local conditions is very important. This issue has been addressed in much detail for soils and hard rocks but there is a gap in intermediate geomaterials such as soft or altered rocks. In order to overcome this problem geotechnical engineers usually adopt principles and methods meant either for soil or hard rocks. The rock mass classification systems such as RMR, GSI etc. are the ones predominantly used. The users of these systems are of-ten unaware of the theory, limitations or the data behind these systems. The aim of this paper is to demonstrate problems or misuses of rock mass classification systems in intermediate geo-materials. The main focus is on the GSI classification system since it is widely used in Greece. Complex geological environments, altered, weathered or poor rock materials are addressed and suggestions on how they should be evaluated with the use of rock mass classification systems are discussed. Situations where the use of these systems produce erroneous results not due to their limitations but rather due to lack of experience and incorrect use are also discussed. Finally, recommendations are made for better use of these systems in practical problems

Jan 1, 2005

By K. M. Stone, N. J. G. Masson, A. C. Woollett

The Jabali zinc deposit in Yemen contains at least 9.4 Mt (10.4 million st) of ore at a grade of 10.7% zinc, 2.2% lead and 77 g/t (2.2 opst) silver. The zinc occurs as smithsonite with minor hydrozincite. The Jabali ore does not produce a zinc concentrate of sufficient grade to be acceptable to a conventional zinc smelter, and it has been necessary to formulate a less-conventional development plan. This involves the construction of a mine and concentrator at Jabali and a metal production facility using a new flowsheet designed specifically for the treatment of oxide material at Yanbu, Saudi Arabia. To give the facility the necessary economies of scale, the Jabali concentrate will be supplemented by feed from other deposits, this may be either oxide or sulfide material. The paper outlines the geology and proposed mining and treatment operations at Jabali, presents the flowsheet for Yanbu and estimates preliminary costs for both operations.

Jan 1, 2003

By A. Yehia, J. S. Hu, J. D. Miller, M. Misra

Fluoride activation has been evaluated by Hallimond tube flotation of collophanite in terms of fluoride concentration, conditioning time, pH, and temperature. The results reveal that efficient oleate flotation of collophanite can be achieved by fluoride activation. Experimental results of fluoride adsorption by collophanite suggest that, at low fluoride concentration, a fluoroapatite-type compound may form on the collophanite surface by chemisorption of fluoride ions at calcium sites. At high fluoride concentration, calcium fluoride appears to form at the collophanite surface involving a surface precipitation phenomenon. The formation of CaF2 on the surface of fluoride-treated collophanite is further substantiated by the FTIR spectroscopic measurements, which suggest a metathetic exchange with phosphate from the collophanite lattice during the surface precipitation process.

Jan 1, 1988

By Z. C. Liu, F. F. Roxborough, Lin. B. B.

The size distribution of coal cut by a mining machine is an important performance factor. It is well established that the main machine system variable that affects product size is the depth of cut. In essence, the greater the amount of coal won by a machine cutting at shallow depths, the greater the proportion of dust and fines produced. Conversely, deep cuts produce less dust and a generally larger product size. When cutting with a rotating drum, as well as with a longwall shearer, the depth of cut always varies from zero in the vicinity of the roof and floor, where most of the dust and fines are produced, to a maximum at mid-drum level. In this paper, minimizing the amount of shallow cutting with a cutting drum is discussed, and the effects of the drum cutting and design parameters on cross-sectional cutting area per revolution are analyzed. This study shows the following: •more shallow cutting occurs during the entry quadrant of a cutting cycle than during pick exit; •the ratio of the projected area of shallow cutting to the total projected area of cutting by a single pick per drum revolution is virtually the same for drums of different radii (however, it decreases as the maximum depth of cut increases); and •for double drums, the use of unequal drum diameters can reduce the production of dust and fines, compared to using drums of the same diameter.

Jan 1, 1998

By David G. Laughton, Richard Poulin, Michael R. Samis

Real options (RO) valuation is an alternative net present value (NPV) framework that is able to incorporate both management flexibility and dynamic project risks. In this paper, management is considering the development of a satellite low-grade zone while operations in a developed high-grade zone continue. If the low-grade zone is developed prior to high-grade zone exhaustion, mine capacity must be expanded before additional production from the low-grade zone can be processed. This expansion can be avoided only if low-grade zone development is delayed until the high-grade zone is exhausted. The RO model presented here allows the development and capacity expansion decisions to be reconsidered on a discrete half-year basis. It delineates price regions, for given levels of high-grade zone reserves, in which it is optimal to develop the low-grade zone, defer low-grade zone development and abandon the mine irrevocably.

Jan 1, 2002

By J. N. Carras, N. W. Bainbridge

In order to further the understanding of spontaneous heating of longwall goafs a numerical model was developed, based on conservation principles applied to the transport of heat, water vapour and oxygen across the god Advective air flow into the goaf is caused by the differential air pressures across the god The air velocity field within the goaf area was computed using Darcy's law. The boundary and initial conditions concern air pressure, temperature and relative humidity. The oxidation rates and heat generation rates of the goaf materials required for the simulation were obtained from laboratory measurements. The main outputs of the model are temperature, oxygen and water contour maps, the rate of air leakage into the go4 velocity field and pressure distribution across the god. The model while still in its development stage, is able to simulate a heterogenous goafs constructed from different materials with different thermal and mass flow properties. Validation of the model by comparing its output with measurements from within goafs is required before the model can be used with confidence in a predictive sense.

Jan 1, 1995

By Derek M. Hutchinson, Don Zeni

The construction of shafts by blind drilling has been made cost effective by advances in technology and experience. The techniques of blind shaft drilling are discussed and a brief history presented. A recent use of blind shaft drilling to access a small gold ore body in Australia is described. Finally, the most recent developments in drilling machinery are reviewed together with possible applications in new and existing mines.

Jan 1, 1987

By R. J. Reuss

Mina Maria is a high-grade, underground copper mine located in the Cananea district of Sonora, Mexico. The ore body is a massive sulfide breccia located in mountainous terrain. A major highway and an electric transmission line pass directly over the near-surface ore body. The mine is operated by Minera Maria SA de CV, a joint venture company that is 51 % owned by Empresas Frisco SA de CV and 49% by Cominco Resources International Ltd. Empresas Frisco is the operating partner. Production began in October 1990. The mining method used is undercut and fill. A continuous miner and a single-boom, hydraulic jumbo mine the ore. Backfill is a weakly cemented sand-gravel mixture that is pneumatically placed. The ore is treated by conventional crushing, milling and flotation. The Maria deposit is located about 40 km (25 miles) south of the Sonora-Arizona border and 11km (7 miles) northwest the city of Cananea and the Cananea Mine. The mine portal, at an elevation of 1780m (5840 ft), is on the east side of an important drainage divide. The mill site is situated about 800 m (2625 ft) northwest of the mine on the northwest side of the drainage divide where the drainage is more favorable. Its elevation is 1860 m (6100 ft) (Fig. 1).

Jan 1, 1992

By W. K. Utt, C. C. Woodward, W. L. Howie, G. G. Miller

The process of roof drilling and bolting is one of the most dangerous jobs in underground mining. In the United States, roof drilling and bolting results in about 1,000 accidents with injuries each year. Researchers, from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are studying the feasibility of using a drill-monitoring system to estimate the strength of successive layers of rock and assess the integrity of a mine roof. Such a system would allow roof drill operators to be warned when a weak layer is being drilled. Using measurements taken during drilling, a neural network can classify mine roof strata in terms of relative strength. The concept has been proven in principle. This research project was undertaken to increase the safety of underground miners, especially those involved in roof bolting. The system should be applicable to the mobile drills now used in underground mines, and the system would likely find wider application as well.

Jan 1, 2003

By W. F. Kane

Underground geologic mapping is an extremely important aspect of any on- going ground control plan. However, the actual use of data derived from such a program is difficult and often leads to subjective analysis. In this regard, computer software has been developed that utilizes a statistical determination of unstable ground conditions based on geomechanical and operational data and collected by mine personnel on a mine-wide, or regional basis. Categorical variables, such as faulting or joint frequency, are selected from local experience to form the framework of a representative data base. Statistical comparisons between the selected variables and a particular ground control problem are conducted and correlations subsequently made. The probability of encountering unstable conditions in virgin areas is assessed as information from these regions is gathered. This data can be derived from surface mapping, cores, and/or geophysical logs. As mining progresses, new data is merged with the existing data base to form a more comprehensive and extensive unit. The advantages of this approach and the acquisition and maintainence of a large data base include the more accurate representation of existing mining conditions, increased confidence in analyzing future problem areas, and elimination of the difficulties which arise when using ground control theories derived for other, often very different, locales.

Jan 1, 1986

By J. A. Herbst, Y. C. Lo

An attempt has been made to parameterize the population balance model for a ball mill based on measurements of the elementary breakage process obtained using an ultrafast load cell device. Detailed insight obtained concerning the fragmentation of particle assemblies with the ultrafast load cell leads to a better understanding of ball mill grinding. The ball mill breakage function and specific selection function are derived from an average single event representing the multiple breakage events which occur in ball mill grinding. Since both the breakage function and the specific selection function depend on the loading mode in the mill, predictions of breakage mechanisms in ball mills are possible by using data obtained in various elementary loading modes. The application of this model to the description of batch ball milling behavior has resulted in reasonably accurate predictions of product size distributions for various energy inputs.

Jan 1, 1992

By Bela Koman

Abstract - A shiploading terminal near Punta Arenas, the southernmost city of the world (lat. 53°-10'S, long. 70°-54' W) is described. Strong winds, choppy seas, frequent gales, rain, and snow make it difficult to load ships at an offshore berth in this area. Detailed site investigations, including a wind-recording program, supplied sufficient information for the analysis of operating conditions. The weather pattern of the entire region, including the predictability of gales, was utilized in the analysis. The results showed that a bulk loading terminal at this location is feasible, provided that the design takes into consideration the specific problems of the site. The final layout shows a terminal that can be approached from several different directions, depending on the direction of the wind. The mooring system is arranged to allow alter- native ways of attaching and casting off mooring lines and executing docking and departing maneuvers. The berth is supported on piles and contains the minimum of structures, relying on a slewing shiploader to reach the ship in any position, with only limited fore and aft shifting of the vessel for loading the extreme hatches. Results of wind recording, statistical analysis of wind and wave data, operating criteria, and the results of berth availability analysis are included in the paper.

Jan 1, 1987

By M. Kumral

The in-situ mineral characteristics of a deposit are simulated by sequential co-simulation and averaging the simulated characteristics within specified block volumes creates a three-dimensional block model. This model is then submitted to optimal open pit and production scheduling algorithms. As the market values of industrial minerals depend on the satisfaction of predetermined blending criteria rather than metal content, a Linear Programming (LP) scheme has been used to identify all blocks that can be included in the blend without violating the grade requirements. The Lerchs-Grosmann algorithm using the blocks identified by the LP program determines optimal pit limits. All blocks that lie outside the optimal pit are removed from the system and the blocks within the optimal pit are submitted to the production-scheduling algorithm. Production scheduling optimisation is done in two stages: Lagrangean parameterisation, resulting in an initial sub-optimal solution, and multi-objective simulated annealing (MOSA) improving the sub-optimal schedule further.

Jan 1, 2002