Search Documents

By V. C. Rogers, K. K. Nielson

INTRODUCTION The potential health impact from uranium milling operations is mainly associated with long-term releases of radioactive contaminants from the mill tailings.(1,2) The major mechanisms for mitigating these potential releases focus on increasing the tailings containment with the addition of migration barriers such as thick earthen covers and clay liners. Some limited investigation has also focused on reducing the radionuclide source terms. This alternative approach has some desirable features, but stringent cost requirements are placed upon source removal methods in order for them to be economically favorable. A cost effectiveness evaluation is presented herein, in which costs for containment methods are used to establish maximum cost guidelines for the source removal methods. The 230U decay chain, shown in Figure 1 contains the radioisotopes of major concern, 230Th, 226Ra, 222Rn and its short-lived alpha-emitting daughters, When the uranium is removed in the milling process, these isotopes, which are normally not removed remain in the tailings solids. The general pathways to the environment from uranium mill tailings are depicted in Figure 2. The dominant pathways are radon to the atmosphere and radium and thorium to a groundwater aquifer. The magnitude of the contaminants released into these pathways can be characterized by the following parameters: 1. The 230Th and 226Ra content. 2. The emanating power for radon. The fraction of radon generated that is free to migrate. 3. The leach rates. Source reduction methods seek to reduce the magnitude of any or all of these parameters. In general the dose rates are proportional to the source terms. For radon production the source term is proportional to the product of the radium concentration, R, and the emanating power, E, so that the risk is reduced by the same factor that reduces RE. For example, if the radium content is reduced by 95 percent, but E is increased by a factor of two, then the dose rates are reduced by an order of magnitude. The source term for the groundwater pathway is not as easy to identify. The peak in the radium concentrations in the accessable water body can also

Jan 1, 1981

By G. Gillet

The conventional magnetic separators used in the mineral industry are equipped with traditional magnetic circuits or with permanent magnets (rare earth). However, when processing minerals with low magnetic susceptibilities or minerals of very small particle size, these separators are inefficient. In addition, a conventional magnetic circuit consumes considerable amounts of electricity to generate a relatively low magnetic field (~2 Tesla). The equipment is also heavy and bulky. Only a separator having a superconducting sole-noid can contribute in solving most of the problems, and only such a separator can produce high magnetic fields with low energy consumption. New developments and the experience acquired in using these superconducting magnets have resulted in new uses for magnetic separation, especially in the environmental area. This paper presents and describes a separation system that uses superconducting magnets that are completely automated and able to treat raw materials (concentration or purification) or liquid industrial effluents containing heavy metals in solution. Several industrial sectors, including the surface treatment, petroleum and chemical industries, are generating effluents containing heavy metal ions. The main metal ions found in such effluents include zinc, copper and vanadium. The purification of such effluents by magnetic separation is performed by adding a certain proportion of iron salts. The treated effluent passes through a superconducting separator where the flocs are retained in a matrix of steel wires. The efficiency of supraconducting high-gradient magnetic separation (HGMS) by this method exceeds 95%. Mineral separation and industrial-waste purification results are presented.

Jan 1, 2000

By P. A. Tuzinski, L. J. Dahl, N. R. Adamson, S. E. Brink, R. L. Blake

The US Department of the Interior, Bureau of Mines is developing a process to selectively extract manganese from oxide ores as part of its in situ mining research program. The Bureau is conducting site characterization studies of two manganiferous iron-formation deposits. These studies include: drill core, regional stratigraphic relationships from the existing geologic database, ore body geometry, geologic structure, hydrologic conditions, accessibility of ore minerals to leach fluid, surface subsidence potential and data collected from laboratory leaching experiments. This information is being used to evaluate the technical, environmental and economic feasibility of in situ mining of manganese for these two deposits. This paper will focus on the stratigraphy, mineralogy, ore textures, fractures, permeability and porosity as they relate to in situ mining.

Jan 1, 1994

By A. Gupta, S. C. Srivastava, K. K. Saroj

Bacterial degasification of methane and conventional methane drainage for generation of power have become accepted practice. Comparative economies of both the techniques have been described. Authors have discussed an alternative technique, involving complete methane biocycle. The first stage of the entire process involves gasification of coal using a consortia of bacteria to generate methane. The generated methane has been proposed to be pumped,as in conventional methane drainage. Technique described is basically similar to underground coal gasification, with the difference that in place of coal combustion, degradation of coal to lower molecular weight compounds by one set of bacteria and then methanogenesis by methanogens, producing methane have been described. Brief account of communities of bacteria that may be employed have been dealt with. Three arguments in favour of proposed technology as an alternative to conventional coal mining are: 1.Total elimination of hazardous operation. 2.Availability of power plants based on methane drainage, assuring comparative economies. 3.Possibility of utilisation of fuel cell technology for power generation giving higher efficiency. All the three phases of complete blocycle viz (1) methane generation from coal (ii) conversion of methane to hydrogen and oxygen (iii) conversion of products so obtained to methane, thereby completing the cycle have been discussed. INTRODUCTION Drainage of methane by conventional pumping process (Boxho,et.al.,1980) not only is helpful in maintaining safe extraction of coal, but with utilisation of extracted gas for power generation, also helps in over all economy of coal mining. This is gradually becoming standard practice for mining of coal in highly gassy mines. An alternative technique (Thakur et. al., 1991) of bacterial degasification of coal seams is also gradually gaining ground. The bye products of this process that is carbondioxide and water, do not contribute towards economy of coal extraction process. However the technique has its own advantage particularly in goaf area for avoiding fire hazard and drainage of methane from coal seams prior to initiation of mining operation. Either of these techniques could be applied in specific situations with success.

Jan 1, 1993

By J. J. Daniels

Advances in borehole geophysical research for mineral assaying and remote detection of mineralization away from the borehole are cited. Nuclear activation measurement research has provided accurate in situ assays of economic metals with neutron-gamma activation, using a high resolution intrinsic-germanium detector. Although nuclear activation analysis is the present "best hope" for obtaining in situ assays for some elements, gamma-gamma and magnetic susceptibility measurements can provide accurate assays for lead-zinc and magnetite, respectively. Borehole optical spectroscopy and X-ray fluorescence are being investigated as possible in situ assaying techniques for some minerals. More laboratory and field calibration research is needed before non-linear complex resistivity (NLCR) can be routinely used as a quantitative assaying tool. Field tests have shown that variations in the local geologic environment can affect the quantitative accuracy of assay values from downhole NLCR measurements. Deeply penetrating borehole geophysical methods are increasingly being used for mineral exploration as drilling costs and exploration have increased. Borehole electrical measurements have been shown to be useful for detecting conductive ore bodies that are not intersected by a drill hole. Hole-to-surface resistivity and surface-to-hole time-domain electromagnetics are demonstrated to be particularly effective for defining mineralized zones in a massive sulfide environment. Borehole gravity meters and three-component magnetometers have been developed and should prove useful for defining geologic anomalies away from the drill hole.

Jan 1, 1987

By Zsolt Csillag, Dragorad Ivankovic, Miomir Ceh, Anna Csordás-Tóth

Results of the common research work of ALUTERV-FKI and RI in field of ore dressing are presented here. Although monohydrate types of bauxites consist of finely dispersed minerals, however, in some cases certain contaminants (carbonates mainly), can be reduced by physical methods before Bayer process. Electronmicroscopy combined with computerized data processing is proven to determine the possibility of beneficiation and to control the different stages of ore dressing. Test results gained by Hungarian and Yougoslavian bauxite samples, contaminated by calcite, dolomite, siderite and pyrite, are discussed. Basic operations were: grinding (mostly dry) and classification, magnetic separation (mostly wet) and selective agglomeration. Only simple processes, having high efficiency and mostly dry ore dressing technique may meet the requirement of economical criteria. 1. [CONDITIONS OF ADAPTING THE BAUXITE DRESSING METHOD] Bauxite is a relatively cheap raw material, occurring in great bulks. Bauxite deposits may often lay far from the traditional ore processing plants, and in such cases the ore reaches the plants after long transportation. Some of these plants must face the difficulty that the resources of high quality ore are exhausted, they fall short of supply and, consequently, they must decide on whether to utilize the existing resources of poorer

Jan 1, 1984

By Donald A. Dahlstrom, Wai-Ping Kam

The mineral industry and individual processing plants are large consumers of energy. While energy conservation has received some attention in the present Federal Administration National Energy Strategy proposal it is obvious that the mineral industry should also continue to emphasize energy consumption reduction for important economic savings alone. As indicated by other studies, comminution is the largest single consumer of energy in the mineral processing plant (1.3% of total electrical energy consumption in the U.S.A.).1 Fine grinding is the largest portion of this amazing statistic. While substantial energy savings have been demonstrated by new machine developments and improved control methods, undoubtedly there are additional areas in comminution where substantial progress can be made. Some time ago, the U.S. Department of Energy published a report on "Comminution and Energy Consumption" by a committee composed of experts in the field of comminution from industry and academia. They identified the following potential for energy savings by specific areas? Classification device design 9-13% Comminution device design 3-16% Control 9% Grinding additive 3-6% Materials 3% It is apparent that the classification device had the first or second highest savings potential. Obviously, serious research consideration must be given to this technology area. A series of three papers have previously been written on the subject of two stage classification research work for ball mill operation by the authors. Accordingly, a brief review will be made. Previous Research Results on Two Stage Classification The hydrocyclone was selected as the type of classification equipment for this study as it represents by far the majority of the devices used in ball milling. While four different hydrocyclone circuits have been proposed by others,3 only two were considered in this work as illustrated in Figure 1. Flowsheet A is truly counter-current in nature in that the product from the ball milling circuit is taken from the first stage overflow

Jan 1, 1992

By Subhash Sethi

The WIPP (Waste Isolation Pilot Plant) Project near Carlsbad, New Mexico. is a research and development project sponsored by the U.S. Department of Energy, designed to demonstrate the safe disposal of radioactive waste. A mine (repository) is being developed 2150 feet below the surface in a thick salt bed, which will serve as the disposal medium. The underground ventilation system for the WIPP project was originally designed based on a fixed project scope. The design criteria and ventilation requirements were developed for the performance of various activities as then envisioned towards the achievement of this goal. However, in light of new information and actual site-specific experience at WIPP leading to a clearer definition of the scope-related programs and activities, it was realized that the existing ventilation system may need to be modified. A re-assessment of the ventilation requirements--based on the current status of the facility and a clearer definition of the scope of the experimental programs, waste storage methodology, mine developmental activities. and current equipment list--indicates a two- fold increase in underground airflows from 210,000 cubic feet per minute (cfm) to 425,000 cfm. Various options to provide the increased airflow to the underground facility were considered and analyzed. Based on the techno-economic analysis, safety and environ- mental considerations, and other conditions unique to a facility like WIPP, it was decided to construct a new shaft to serve as the primary fresh air intake, along with the installation of additional fans in parallel with the existing set up. Low cost and the ease with which the new design could be implemented and integrated into the existing ventilation system with minimum impact on current activities and projected schedules were the guiding factors in designing the shaft and related ventilation modifications.

Jan 1, 1987

By V. C. Rogers, K. K. Nielson

INTRODUCTION An evaluation of the radiological health risks from uranium mining and milling requires the determination of several key parameters. As shown in Figure 1, the first step is the estimation of the radioactive source term. The radionuclides in the ore consist of the 238U decay series nuclides shown in Figure 2, the 235U series nuclides, and 40K. The 238U decay series isotopes dominate the source term, with the 235U series isotopes causing less concern and 40K remaining at background levels. [ ] Specifically, the risks from uranium mining and milling are mainly associated with 230Th, 226Ra, 222Rn, and its short-lived daughters. These radioisotopes are mainly alpha-particle emitters; hence, some dispersion mechanism is necessary to bring them into intimate contact with man so that they can be inhaled or ingested For water pathways, the leaching of the isotopes from [ ] the solid ore or tailings provides a measure of the amount of contaminant initially available to the environment. For the air pathway, dust-creation mechanisms such as blasting, crushing or general resuspension processes dominate for 226Ra and 230Th. However, 222Rn, being a chemically inert gas generated from the decay of 226Ra, can migrate through the ore, overburden and tailings over considerable distances. As shown in Figure 1, the next step in the pathway to man is environmental dilution and delay. For the water transport mechanism, the delay in the isotopes reaching an accessible water supply may be considerable (several thousand years or more), but for airborne nuclides the dispersion in the atmosphere is rapid and constitutes the main mitigating factor. Considerable ventilation is provided in underground mines to dilute and remove radon and its daughters in order to keep their concentrations low and thereby minimize their inhalation by miners. The rate of uptake by both the workers and the general public is often difficult to ascertain. It involves breathing rates, rates of water consumption and other poorly-defined parameters. The final steps are the risk estimators used to predict doses and cancer rates from the inhaled radon daughters and ingested or inhaled radium. Many

Jan 1, 1981

By Steve Van Kouteren

Filters and absorbents purify, clarify, and clean many types of liquids by removing solid particles. In addition, absorbents provide a convenient way to handle liquids and to clean up liquid wastes or spills. Filtration or absorptive processes are accomplished either in a mechanical way, as in absorption and filtration, or in a chemical way, as in adsorption. In filtration, minerals and rocks used as filter mediums are extensively utilized in applications requiring the filtration of high volumes of liquids. End use applications include liquid food products, waste waters, petroleum and chemicals, and drugs and pharmaceuticals. Upon closer examination of all of the materials used as filters and absorbents, industrial minerals and rocks represent only a small proportion of the total amount, as shown in [Fig. 1] (Rees, 1991). Given all the industries that use these minerals, most of the volume is concentrated in a few major end-use markets. Within these major end-use markets, a handful of minerals account for most of the total volume and value. The focus for this chapter will be to discuss the industrial minerals and rocks used as filters and absorbents in the most important markets. The selection of the minerals and markets to review is solely based on the total volume of material used and in special cases, those where the value of the market and material is high. The major materials include diatomite, perlite, sand, gravel, and such specialty clays as montmorillonite and attapulgite. These materials are mainly used for the filtration of food, chemical, and petroleum products. In addition, they are used as absorbents for pet litter and oil and grease spills, and as carriers for pesticides and fertilizers.

Jan 1, 1994

By Robert Seal, James J. Rytuba, Michael P. Hunerlach, Roger Ashley, Dean Enderlin

Cessation of open pit mining in 1996 at the McLaughlin hot-spring type gold deposit has resulted in the development of two pit lakes that will be managed as permanent lakes with a total storage capacity of 10,000 acre-feet. The south pit lake developed from alkaline ground water infiltration and had an initial pH of 7.2. It contained high concentrations of boron and chloride, indicating that it consisted of a mix of meteoric and evolved connate waters. Numerous carbon dioxide gas vents were present initially in the shallow south pit lake, but as the pit lake increased in depth, gas venting ceased and carbon dioxide is retained in the lower layer of the chemically stratified lake. Continued increase of dissolved carbon dioxide in the lower layer increases the potential for a limnic eruption. A chemocliie occurs at a depth of 47 m. The upper layer of the lake has lower pH, temperature, and conductivity than the lower layer. Effluent from ore and waste rock piles directed into the south pit lake has contributed to high levels of antimony, arsenic, cobalt, copper, mercury, nickel, and zinc. Iron oxyhydroxide is abundant in mine effluent that enters the pit lake and adsorption onto this phase has lowered the arsenic and antimony concentrations. The north pit lake formed primarily from winter surface runoff. The acidic water, pH 4.56, initially had high concentrations of cobalt, mercury, and nickel derived from weathering products of pyritized serpentinite and shales. Buffering by wall rocks has established a slightly alkaline pH of 7.62. The concentrations of trace metals in the north pit lake have substantially decreased due to continued dilution of the lake by surface runoff and remediation of parts of the pit walls that have been covered by backfill.

Jan 1, 2000

By Carl E. Nelson

Shallow epithermal stockworks hosted by maar eruption craters contain over ninety percent of the bulk mineable gold identified to date in the Circum-Caribbean region. Pueblo Viejo (Dominican Republic) and Santa Rosa (Panama) contain combined gold reserves of over 600 tonnes. Bulk mineable gold deposits are also being discovered in and around veins that were formerly mined underground. Bellavista, El Recio and San Martin (Costa Rica) contain combined announced gold reserves of over 50 tonnes. Representative rock suites collected at 8 bulk mineable gold deposits include 291 samples of veins and vein stockworks, hydrothermal eruption breccias, sinter, variably altered host, unaltered host, nearby intrusive rocks and basement. Analyses completed to date show that Circum-Caribbean epithermal ores are enriched in arsenic, mercury and antimony as well as gold and silver. Exploration efforts in the region naturally focus on districts with past production. However, an order of magnitude more bulk mineable gold has been discovered in shallow epithermal stockworks outside of the old bonanza vein camps. Exploration guides include basal island arc volcanic sequences, hydrothermal and hydrovolcanic (maar) eruption breccias, thinly-bedded carbonaceous maar sediments, and hot spring-related silicification and argillic alteration.

Jan 1, 1990

A chartered bus with about 30 attendees of the just completed 1998 SME Annual Meeting headed toward Green Cove Springs, FL, which the author had been told was located somewhere south of Jacksonville, FL. In conjunction with the meeting in Orlando, RGC (USA) Mineral Sands provided a tour of its facility. The author had worked with heavy minerals on a laboratory scale, performing the usual gravity and magnetic separations, but had never been to a heavy mineral mine and processing facility. Years ago as a metallurgist, the author once applied for a job in a heavy mineral operation in Florida -it may have been the same operation. After turning north on to Highway 95, the endless billboards promoting beach-front retirement communities proved the Atlantic ocean was just a few miles away (although the author never caught a glimpse of it). After another hour, the bus suddenly turned west and continued inland for about 65 km (40 miles). The thought occurred, "We are talking about beach sands, what are we doing heading away from the ocean?" As the bus continued inland, the author was struck by the flatness of the land and by the lakes, rivers and wetlands. He was also impressed by the many fine stands of pine and hardwoods. The office of RGC (USA) Mineral Sands is located about 16 km (10 miles) south of Green Cove Springs. Upon leaving the bus, members of the tour were greeted by Graeme Sloan, general manager, and Elliot Mallard, manager of mining. They provided some general information about the operation, including a slide show. RGC's Florida operation produces four concentrates: zircon (ZrSiO,), rutile (TiO,), ilmenite (FeTiO,) and leucoxene (an alteration product of ilmenite containing 67% to 70% TiO,). With a work force of about 170, the annual production of the above products is about 23,27, 45 and 14 kt (25,000 30,000 50,000 and 15,000 st), respectively. RGC also has other mineral sand operations, in addition to gold and base metal mines, mostly in Australia.

Jan 1, 1998

By Howard L. Hartman

If I told you tonight at the outset that my prognastications for the future of mine ventilation were imparted to me by a palm reader or inspired by a vision, you'd dismiss what I had to say before I said it! If, on the other hand, I told you that my forecasts were the result of an elaborate computer model, derived from a complex algorithm, which in turn relied on finite element analysis -- and the entire projection confirmed by on-site experiments with a turbo hybrid-flow mine fan -- you'd sit up in anticipation and hang on my every word!! All of which places me in a terrible dilemma, because my predictions really lie somewhere in between. My intent is to talk to you out of my background of forty years in mine ventilation, looking ahead to conditions that I expect to prevail in the next fifteen years. You may be curious why I picked an unlikely time span of 55 years for my overview, and my response is that it bridges a career lifetime. "The last forty", of course, corresponds with the period of my professional employment since graduating with a B.S. and M.S. here at Penn State. "The next fifteen" bridges the period I expect (the Lord willing) to remain professionally active -- and coincidently brings us into the beginning of the 21st century. (I must confess to stacking the deck a bit: Since it's infinitely harder to look ahead than to look behind, I purposely minimized the forecast period and maximized the history! Besides, "forty" and "fifteen" have a nice phonetic ring, perfect 20/20 vision sums to "forty", etc., etc.). With these disclaimers, I'll invite you to join me now in a fast 55-year overview of mine ventilation, of necessity limited to a broad-brush treatment of the subject. (After all, this is an after-dinner talk, not a marathon!) In each- segment, I've selected the seven topics that seem to me of paramount importance: in the first part, seven accomplishments in retrospect, and in the last, seven expectations for the future. (The number "seven" needn't confound you, either: In the bible, it signifies "wholeness" or "completeness".))

Jan 1, 1987

By D. Dunbar

The flooding of open pits is now receiving considerable attention from the mining industry as an option that may minimize environmental impacts, particularly when anoxia in pit-lake deep waters can effectively eliminate oxidation of pit-wall sulfides. This paper describes a state-of-the-art, coupled physical-geochemical pit-lake model. The model is used to verify that a controlled, two-stage infilling of the open pit at the Kori Kollo gold mine, southeast of La Paz, Bolivia, would result in a cost-effective, environmentally responsible closure strategy. By filling the pit initially with highly saline surface waters and naturally saline deep groundwater and then capping with fresh river water, a very stable and strongly stratified pit lake will be developed. In addition, the stratification will result in the isolation of metal-rich saline bottom waters from surface waters of good quality. Results of this model provide defensible predictions of the physical stability and evolution of water quality in the Kori Kollo pit lake over time. The model results indicate that anoxic conditions will develop below the fresh-saline water boundary within one to two years, followed by the rapid onset of sulfate-reducing conditions in the bottom waters. Hydrogen sulfide produced by sulfate reduction will readily react with dissolved metals to form highly insoluble metal sulfides. The process results in the gradual removal of metals from the water column and the concomitant improvement of water quality over time. A notable benefit of this strategy is that it can be fully integrated with other mine site closure options as well as future environmental-management strategies. The proposed plan allows for the safe isolation of saline waters, the potential for passive treatment in anoxic bottom waters of ARD seepage from other mine site operations, should they arise, and a repository for future reactive wastes that could be effectively isolated in a physically and chemically stable environment.

Jan 1, 2003

By J. Herbst, H. B. Treweek, V. R. Degner, G. Poling

Current mineral industry trends toward handling the high tonnages of lower grade ore and tailings retreat lead to a continuing need for large volume flotation cells. The benefits which accompany the larger cell flotation circuit include reduced capital cost, less mill floor space, reduced operational complexity, and less maintenance, provided the metallurgical performance and solids suspension capability of the cell are not compromised. This study reviews development considerations pertinent to large mechanical air induction type flotation cells from the standpoint of cell internal hydrodynamic characteristics and metallurgical performance. While the importance of process related factors such as chemical usage, pH control, solids size and loading, and circuit arrangement cannot be denied, this study will emphasize the relationship of cell size (volume), mechanism geometry (impeller diameter), and mechanism operating conditions (rotor speed and submergence), to air transfer, liquid circulation, liquid "rise velocity" and mechanism power draw. Specific hydraulic performance maps for large capacity 300 and 500 cu ft flotation cells will be reviewed in terms of the relationship between the operational variables and the air and liquid flow conditions within the cell. Metallurgical results, obtained under plant operating conditions for 300 and 500 cu ft cells, are included to illustrate the metallurgical performance similarity of flotation cells which follow hydrodynamic scale-up criteria set forth in this investigation.

Jan 1, 1976

Cost reduction programs can focus on total cost or unit cost, but unit cost is usually the principal objective. The production cost per unit is: [Unit cost = Total cost Production volume] Consequently, any activity that reduces the total cost or increases the production volume will reduce the unit cost. Production volume is increased by (1) maximizing the availability of the production equipment and (2) maximizing equipment performance during periods of operation. Most operations managers routinely focus on volume because the factors influencing volume are generally well understood and congruent with the managers' technical skills. In fact, production volume (as a percentage of maximum achievable capacity) is widely recognized as one of the most significant measures of operational performance.

Jan 1, 1999

By Romeo S. Jurani

Yucca Mountain, located in Southern Nevada approximately 160 krn northwest of Las Vegas, is currently the site of intensive surfacebased and underground investigations. The investigations are required to determine if the site is suitable for long term isolation of the Nation's high level nuclear waste inventory. A major component of the program is the Exploratory Studies Facility, or ESF. The ESF, when completed, will consist of approximately 25,600 meters of tunnels and drifts. The network of tunnels and drifts (Figure 1) will house and support a wide array of testing programs conceived to provide physical information about the site. Information on geologic, geomechanical, and hydrologic data will be used in the repository design if the site is found suitable. Besides a few special requirements, the general ESF ventilation criteria during construction are similar to that of commercial tunneling and mining operations. The minimum air velocity at the Tunnel Boring Machine (TBM) and other active mining faces is 0.51 meter per second (m/s) (100 feet per minute [fpm]). Airways, estimated leakages and ventilation controls are converted into equivalent resistances for input to mine ventilation network computer simulations. VNETPC Version 3.1 computer software is used to generate the ventilation models for optimized system design and component selection. Subsequently, actual performance of the ventilation system will be verified and validated to comply with applicable nuclear regulatory quality assurance requirements. Dust control in the ESF is dependent on effective dust collection, enclosure, and airflow dilution. Minimum use of water, as feasible, is necessary to avoid adding moisture to the potential repository horizon. The limitation of water use for test drilling and TBM operation, and the rigid compliance with applicable federal and state regulations, make the ESF a ventilation design challenge.

Jan 1, 1995

By Frank Hagar, George M. L. Robinson

NTRODUCTION The Resource Conservation and Recovery Act and CERCLA (SUPERFUND), in many instances, has had an adverse economic impact on the hardrock mining industry. Over the last few years, many abandoned and active mining operations have been added to the Environmental Protection Agency (EPA) National Priority List (NPL) . When the property is placed on the NPL the operator or EPA is required to conduct extensive environmental assessments to determine if historical mining practices have degraded the existing environmental. If degradation has or will continue, the responsible party is required to implement appropriate remedial action plans. If a responsible party is not identified, the EPA implements a cleanup program. Experience has demonstrated abandoned and active mining operations are subject to RCRA, and possibly Super- fund, if the mine has not adopted appropriate hazardous waste disposal management procedures. If off-site contamination has occurred, the operator will be required to mitigate the impacts and will be required to adopt additional procedures to minimize future impacts. Since the passage of RCRA and Super- fund, many mining operators are adopting management procedures to monitor and inventory hazardous sub- stances and wastes generated, stored and disposed on site. Many operators are in a difficult position because ore, waste rock, process chemicals or other solid waste, in many instances, can be classified as hazardous waste. If the process or other solid waste is deemed to have the characteristics of a hazardous waste, the operator can inventory and adopt appropriate, in- expensive management procedures. However, if the ore or waste rock has hazardous waste characteristics, in- expensive control technologies are impossible to implement. Since existing statutes and regulations require hazardous waste control, the operator will be required to inventory, characterize and monitor all aspects of the mining operations including but not limited to exploration, mining, ore processing and waste disposal. During this process, geological, geotechnical, geochemical, waste and ore volumes, and process materials must be tracked throughout the mining process. To accomplish this task, the most cost effective method to maintain documented and accurate records, is through the implementation of an integrated database management system. The database management system can be used to model and simulate the entire mining operation and if necessary, used to predict whether the operation is in compliance with existing regulations. The developed database can also be used to operating optimize mining and disposal costs.

Jan 1, 1987

By John L. Stauffer, Allan Lipton, Kim Leitzel, Lesley Gaydos, Laurence M. Demers, Douglas C. Kuhn

Eicosanoids and cytokines produced by the alveolar macrophage (AM) are key mediators of pulmonary inflammation and fibrosis resulting from occupational exposure to mineral dust. In order to determine if eicosanoid and cytokine production are altered by chronic inhalation of coal dust, we compared the production of prostaglandin E2 (PGE2), thromboxane A2 (TxA2), leukotriene B4 (LTB4), interleukin 1 (IL-1), tumor necrosis factor (TNF) and platelet-derived growth factor (PDGF) by cultured AM from non-smoking normal human volunteers and coal miners. Inhibitors of eicosanoid biosynthesis were administered to AM from coal miners in order to determine if a link between eicosanoid and cytokine production exists in these cells. Basal PGE2, TxA2, TNF and IL-1 production by AM from active miners was increased compared to AM from normal volunteers. However, the production of these eicosanoids and cytokines by AM from former coal miners was reduced compared to control AM. Administration of the cyclooxygenase inhibitor, suprofen, and the lipoxygenase inhibitor, nordihydroguaiaretic acid, reduced PGE2 and TxA2 production in miners' AM but had no effect on LTB4, IL-1 or PDGF production. Specific inhibition of thromboxane synthase by UK38,485 was associated with a significant reduction in TNF production in active miners' AM but had no effect on PGE2, LTB4 or IL-1 production. The prostacyclin analogue ZK96,480 also specifically inhibited TxA2 production in active miners' AM. The results of these studies suggest that coal dust exposure is associated with alterations in AM eicosanoid and cytokine production which may be relevant to the development of pulmonary inflammation and fibrosis. In addition, the lack of effect of inhibitors of PGE2 biosynthesis on IL1 production in miners' AM suggests the production of these intercellular messengers may not be linked in AM chronically exposed to coal dust.

Jan 1, 1991