Search Documents

By James L. Noble

A small placer operation can be defined as one with a throughput capacity of 250 cubic yards an hour or less. The success of small placer operations after the values have been established, depend entirely on having the proper design. There are various types of placer deposits including marine, beach, desert, stream, bench, underground and even frozen placers. Each is unique and requires special considerations. Size distribution of alluvial placer ore varies from sand to large boulders. When boulders occur, they can become a problem to all types of excavating to a greater or lesser degree. Clay content and cementing are common in placer deposits. Some clay disperses easily in water while others, if not handled properly, will form clay balls that pick up gold and carry it to tailings. Overburden, depth of bedrock, vegetation, and ground and surface water must all be considered when designing a plant. Any equipment chosen should be capable of processing large volumes of material at a high efficiency. There are usually five steps to processing placer gravels, as follows:

Jan 1, 1992

By J. M. Mutmansky

This paper outlines the results of a study of the opinions of practicing engineers concerning the value of environmental engineering courses in a mining engineering curriculum. One hundred engineers with significant experience in mining-related engineering work were carefully chosen. Of the 67 responses, about half were from mining engineers, and the other half were from environmental engineers. In this paper, the results of the survey are outlined. The number and type of courses recommended by the respondents are summarized as well as the specific topics recommended for inclusion in a mining engineering curriculum. The survey form also asked for the stages in the mine life when environmental experts were needed and the percentage of environmental engineering performed by outside experts for many mining-related environmental tasks. The results of this line of questions are provided. Finally, the paper offers a comparison of the results for environmental engineers and mining engineers and analyzes the differences.

Jan 1, 2003

By T. W. Oshnock

Pulverized coal (PC) and other injectants can be injected into the blowpipes of a blast furnace to decrease coke requirements. Throughout the history of blast-furnace development, there have been many attempts at injecting PC. In the 1960's a more serious effort was made to improve pulverized coal injection (PCI) technology. However, because of the additional capital requirements and the projected near-term inexpensive cost of other injectants, very few PC1 systems were installed. When the second oil crisis occurred around 1979, the shortage and high cost of fuel oil caused blast-furnace operators to operate without oil injection. It was soon discovered that blast- furnace operation without oil was not as smooth or efficient. Experiments with PC1 quickly showed that coal was a good replacement for oil which resulted in the rapid application of PC1 in both Europe and Japan. As a result, PC1 technology for blast-furnace operation has progressed rapidly during the 1980's. This paper will describe the worldwide status of PCI, characteristics of different PC1 systems, the effect of PC1 on blast-furnace process parameters, and the economic effects of using PCI. Results from the USS Blast-Furnace Thermochemical Projection Model comparing the effects of different coal properties and the effects of other tuyere injectants such as oil and natural gas will also be described.

Jan 1, 1988

By Jacques Villeneuve, Stéphane Brochot, Jean-Claude Guillaneau, Marie-Véronique Durance

Since 1986, BRGM has been developing a powerful process simulation software package, USIM PAC. These last years have seen significant developments in mineral processing technologies, particularly in hydrometallurgy, bio-hydrometallurgy and mineral liberation. The new version of the simulator, USIM PAC 3.0, incorporates these modem-processing fields. Its structure and tools allow the user to take into account, at the same time, a wide range of technological, economical and environmental aspects. The improvement of the existing features and the introduction of new unit operation mathematical models and tools such as the supervisor, global optimization, workshop model or chemical reactions contribute to a global approach in mineral processing design.

Jan 1, 2002

By N. S. Tanious

This paper summarizes results from an investigation into possibly the largest coal pillar failure in the USA. The newly opened coal mine worked an 3.35 m (11 ft) seam under overburden depth that ranged from 91 to 671m (300 to 2200 ft) . The mine main entries, and the enclosed pillars, experienced a massive slow squeeze. The squeeze could not be controlled and the mains were lost. A new set of mains were driven. Entry convergence (closure) measurements were carried out behind the advancing face to monitor stability. Pillar stresses were also measured under four different depths of overburden: 229.433, 472.579 m (750,1420,1550, and 1900 ft). The strength of pillars in the new mains was calculated from the loads that triggered the failure in the old mains, using three pillar strength formulas. The stress measurements showed that the new pillars supported more load than their predicted strength, indicating that current strength formulas are inadequate under deep conditions.

Jan 1, 1992

By Surendra K. Mishra

Metallic and oily components are the major contaminants of industrial wastes. Underground burial and incineration have been the commonly practiced methods of waste management. To provide a relatively more permanent solution, different processes have been developed. In addition to reviewing these processes, potential of using flotation as a process to treat hazardous metal and oil contaminated wastes is discussed in this paper.

Jan 1, 1989

By Gordon I. McPhail, John D. Nelson

Tailings management represents a major portion of the cost associated with extraction of gold. For each gram of gold extracted, 150 to 200 kg of waste material is produced. Because of environmental concerns and unwillingness of society to accept environmental damage caused by poor waste management practices it has become essential to follow responsible and safe practices in tailings management. This paper presents general aspects of tailings management and discusses different techniques utilized. Characteristics of tailings and the effects that these have on stability and environmental aspects are discussed. The paper also discusses the effect of mine back-filling practices on the surface disposal of the remaining tailings fraction.

Jan 1, 1987

By John Matthews

During 1982 and 1983, it became increasingly clear that North River No. 1 Mine would have to buy a set of replacement longwall shields. Despite extensive efforts to make improvements, the shields that were in place at that time were incapable of holding the roof. North River Energy had limited experience in specifying and acquiring longwall roof supports, but a great deal of experience with our conditions and needs. We there- fore compiled a shield evaluation method that uniquely responded to our situation. The resulting system emphasized teamwork among operating, maintenance and engineering personnel. The charge from management was threefold: select shields to support maximum expected loads, optimize face operations, and pay attention to detail. Final selection was made objectively, based on all available information. We chose a 5516 KN (620 tons) support with a minimum yield load density of 760 KN/m2 (7.9 tons/ft2). This paper reviews our process of specification, design, prototype testing, and fabrication, and offers some relevant suggestions.

Jan 1, 1986

By Winthrop F. Watts, Robert W. Waytulonis

During the 1980's. the Mine Safety and Health Administration (MSHA) proposed new regulations for the use of diesel equipment in underground coal mines, and the National Institute for Occupational Safety and Health (NIOSH) recommended that whole diesel exhaust be regarded as "a potential occupational carcinogen", and that reductions in exposure to exhaust pollutants would reduce excess risk. During the same time, the Bureau of Mines tested new emission control technology to minimize diesel emissions. The objectives of this paper are to discuss the major issues regarding diesel exhaust emissions. especially diesel particulate matter (DPM) , and to highlight emission controls that will be available. DPM is a potential health threat because it is respirable in size and is composed of nonvolatile carbon with adsorbed or condensed compounds. These compounds include potentially mutagenic or carcinogenic hydrocarbons such as polynuclear aromatic hydrocarbons and sulfates. DPM contributes to the degradation of air quality in mines with typical mean concentrations ranging from 0.2 to 1.0 mg/m3. In addition to adequate ventilation, control of DPM can be achieved by implemention of improved work practices, regularly scheduled engine maintenance, and emission controls.

Jan 1, 1991

By Matthew J. DeMarco, Anthony T. Iannacchione

Coal bumps have presented serious mining problems in the U.S. throughout the 20th Century. Fatalities and injuries have resulted when these destructive events occur at the working face. Persistent bump problems can result in abandonment of large reserves or lead to premature mine closure. Through the years, a1ternative techniques such as artificial supports, extraction sequencing, destressing, pillar design changes and specific pi1lar retreat practices have been successful1y imp1emented to mitigate coal mine bumps. Several techniques have evolved for room-and-pi1lar operations that control the way the roof rock breaks, regulating the manner in which stresses are redistributed in the mined section. Special mine layouts employed in longwall mines have also proved to be successful in safely redistributing or containing excessive loadings. However, with ever increasing production rates, greater overburdens and new mining systems, the need to evolve even more effective bump control designs will continue to challenge the U.S. coal mine industry.

Jan 1, 1992

By R. Fraher

The control of mine roof is of vital interest in underground coal mining not only for reasons of safety, but also to avoid the high costs of cleanup, resupport and production losses that can result from roof falls. The difficulty in determining roof stability mine-wide is due in large part to the broad variation of geologic and structural conditions that typically exist throughout a mining area. To ensure a stable roof over the entire mine, support systems must be selected to minimize the possibility of failure. The magnitude and cost of the support selected is a trade off against the cost of the number of falls that can still occur after it is installed. Because of the large number of variables involved in analyzing and optimizing roof stability versus support, a digital computer simulation was selected to find a cost effective solution to roof support design. A total cost approach is used which includes the actual cost of the roof support as well as the cost of the roof fall in terms of resupport and loss of production (Fraher 1990a). A Monte Carlo simulation program called ROCSIM (Roof control Optimization Cost SIMulation) has been developed for determining the optimum roof control system and design layout for underground room-and-pillar mining.

Jan 1, 1992

By T. S. Golosinski

This article reviews current contract mining practices in Australia. Various types of contracts are reviewed, including partnering arrangements and alliances between the contractor and the mine owner. Applicability is also discussed of various types of contracts to specific mining situations, as is their effect on overall mine performance.

Jan 1, 1998

By V. W. Skema, M. W. Smith

Pennsylvania has 4,000 km (2,500 miles) of streams that do not meet water-quality standards due to acid mine drainage (AMD), making AMD the greatest cause of water pollution in the state. The problem is mainly caused by abandoned coal mines. To abate AMD, Pennsylvania is using a watershed-based approach that includes remining as a key component of a comprehensive restoration strategy. The Tangascootack Creek Water-shed was targeted for AMD restoration through remining. Geologic mapping and overburden data were analyzed using Earth Vision software to identify areas of coal reserves that could be remined to improve water quality. Incentives are offered to encourage mining in these designated areas.

Jan 1, 2002

Diamond wire rock cutting is the most widely used technology in carbonate stone quarrying owing to technical performance and block face quality. Interest is also growing for siliceous deposits. This paper deals with the problem of optimum wire utilization under restrictions regarding a set of variables and parameters. A computer program of general applicability has been set up with the aim of studying the most suitable combination of technologies and the effect on the technical and economic results of bench geometry, overall quarry yield, market -stone value, quarry size as well as the quantity, productivity and price of human and material resources and their organization in the elemental working cycle. Two quarrying problems are considered as significant instances a granite and a travertine quarry. The results are illustrated and discussed.

Jan 1, 1989

By Ralph P. Hackl

The Congress gold property, located near Goldbridge, B.C., is extremely refractory with most of the gold disseminated in fine- grained arsenopyrite. Metallurgical testwork conducted by Giant Bay Biotech Inc. indicated that biooxidation pretreatment was capable of increasing cyanide gold recovery from the ore to greater than 90%. To determine if the bioleach process could be successfully scaled up, a 225 cubic meter commercial size bioleach reactor was built and tested at the mine site in 1989. At that time the tank was the largest bioleach reactor ever operated. This paper discusses our experiences in operating the tank, summarizes some of the data obtained and describes the problems encountered.

Jan 1, 1990

By Fabio Amaya, Andrés Marulanda, Ramiro Gutiérrez, Alberto Marulanda

The behavior of a salt rock mass is strongly related to a creep phenomenon. The amount of creep depends on the level of stress generated in the underground excavation. Additionally, security conditions and the lifespan of an underground cavern excavated under this geological conditions depend on the evolution of creep. Based on the experience of the failure of the Old Underground Salt Cathedral of Zipaquirá(Colombia) and the construction of the new one, the theoretical framework to predict the creep behavior of a salt rock mass is explained. The theoretical formulations are calibrated based on actual observations of the material behavior to predict the lifespan of this striking structure.

Jan 1, 2003

By Christopher Haycocks

Subsidence induced innerburden shearing and stress fields, whether active or passive, frequently contribute to significant ground control failures in overlying seams. In this paper proven multi-seam technology is used on upper seams to forecast and quantify the magnitude and severity of damage and the increased mining risk due to interaction. Increased upper seam ground control problems are demonstrated using hazard mapping which provides a viable technique for utilizing damage predictions in design.

Jan 1, 1986

By J. Herbst, K. Fallenius, G. Poling

Since 1970 a new series of pneumo-mechanical flotation machines has been developed by Outokumpu Oy. The cells have a completely new type of mechanism based on a recently-developed theory of conditions necessary for dispersion of large amounts of air. The mechanism was developed in 3 cu m cells and scaled to 16 cu m cells. Rotor and stator description, scale-up theory, and practical experience with the 16 cu m cell are presented.

Jan 1, 1976

By J. Felipe Costa, Andrew H. White, Marcot T. M. B. Vilhena

Ordinary kriiing (OK) is an interpolation algorithm mostly used in earth sciences applications where it provides satisfactory results. Robust kriging (RK) is an alternative algorithm which at- tempts to minimise the problems caused by the existence of outlier values within a given data set. Robust kriging essentially consists of an editing step prior to running the traditional OK method. This study compares the interpolation results obtained by OK and RK. Two data sets were used. The first data set consists of 140 samples mimicking a drilling survey named cluster.dat. An additional feature of this sample data is that its parent population, the reference data set, is available, thus permitting direct quantitative assessment of the effectiveness of a given estimation technique. The second data set consists of a grid sampled at 1x1 m. The estimates obtained by OK and RK using cluster.dat were compared to the reference data set. RK provided better results in terms of quality of the estimates than OK

Jan 1, 1996

By Y. C. Kim, M Nataraja, J. T. Buckley, D. H. Tiktinsk

The Nuclear Waste Policy Act of 1982 (NWPA) assigns the U.S. Department of Energy (DOE) the responsibi1it.y of locating, constructing. operating, closing and decommissioning a nuclear waste repository. Prior to submittal of a licensee application to the U. S. Nuclear Regulatory Commission, the DOE is required by 10 CFR part 60 to conduct a program of site characterization for the site to be described in such application. Site characterization includes an exploration and research program in the field and laboratory to determine the geologic conditions and ranges of those parameters which are necessary for determining the suitabi1it.y of the site as a geologic repository. The information thus collected should be able to establish with reasonable assurance that the public and environment will be adequately protected from the hazards associated with a repository at the site. This paper demonstrates by example a geostatistical approach which, on the basis of the existing limited data base, can be used to evaluate (1) whether existing information on a certain parameter is adequate to be considered representative. (2) if additional information is required, where should the additional sampling or testing be performed, and (3) whether the new1.y acquired data along with the existing information constitute representative data.

Jan 1, 1986