Search Documents

By M. Manrique, S. A. Pirzada, P. R. Taylor

A thermal plasma-assisted laminar flow reactor was used to evaluate the kinetics of converting alumina to sodium aluminate in flight. Free energy minimization calculations were used to determine experimental conditions. The experimental variables included alumina particle size, alumina/sodium nitrate molar ratio, temperature and residence time. A mathematical model for the conversion was developed and validated. Experimental and mathematical results are presented.

Jan 1, 1998

By A. I. A. Salama

A computationally efficient technique for generating a balanced set of density or size separation data is developed. The technique proposed utilized minimization of a modified form of error squares to generate the optimum estimates of outputs mass yields (splits) and balanced direct mass distributions of feed and outputs. The estimated separation data set satisfies mass balance conditions of the streams mass distributions around the separator. The technique proposed avoids the generation of small negative values for the estimated feed and outputs direct mass distributions. Actual data are used to demonstrate the technique proposed.

Jan 1, 1996

By H. T. Mulryan

Talc is used as an essential ingredient in a variety of plastics applications ranging from polyester body patch compounds through polypropylene automotive, appliance and household furniture components to high performance parts made from liquid crystal engineering resins. This paper focuses on polyolefin applications, the three-tier market for talc in polypropylene, the effects of various tales in typical compounds and trends in each market segment. Emphasis is given to emerging markets, examples of which are polypropylene compounds that mimic higher cost resins, and polyethylene films. Customer requirements for tales for these purposes are discussed.

Jan 1, 1994

By James L. Parks

This paper describes improvements in SAG and AG mill liner designs and their cumulative effect on wear life and mill availability. Routine procedures used by many SAG and AG mill operators to improve liner life are reviewed. Guidelines are provided for estimating the time required to replace worn liners along with practical methods to reduce downtime for liner replacement. Finally, the effects of mill operating conditions on liner wear life and breakage are considered.

Jan 1, 1998

By Simon T. Johnson, Robert J. Fowell

The application of roadheading and drag tool equipped machines requires an assessment of both cutting performance and tool consumption. Neither parameter can be assessed purely from compressive strength and tool consumption is often neglected, at a cost to the project. Results from in-situ monitoring show that a measurement of relative abrasivity using the Cercharscratch abrasivity test provides a basis for the assessment of tool consumption. This can be modified by also considering the effects of the machine specification and the rock mass quality.

Jan 1, 1986

By A. McCombs

Previous models describing the aggregation of polymer-coated particles fail to take into account the fact that there are a limited number of sites onto which a polymer segment can adsorb, called "active" sites. Thus, the collision efficiency is a factor not only of the fractional surface coverage, but also of the number of active sites. In this study, a physical model of the flocculation system was devised in which the number of these sites could be varied, in order to study the effect on particle aggregation.

Jan 1, 1988

By John W. Conn, Harry C. Verakis

An explosion in an underground coal mine can have a devastating effect on the main fans used to provide mechanical ventilation. The Code of Federal Regulations, Title 30, Part 75.310 (CFR, 1992), specifies that each main mine fan shall be offset by at least 15 feet (4.6 m) from the nearest side of the mine opening unless an alternative method of protecting the fan is approved in the ventilation plan. Also, each main mine fan shall be protected by one or more weak walls or explosion doors. This paper presents venting and fan configuration designs which provide a comparable degree of safety for explosion protection. Design flexibility is enhanced and a means for consistency in safety judgements is afforded.

Jan 1, 1993

By Mark W. Springett

The sampling of precious metal deposits entails inherent problems due to the low mineral abundances, high mineral specific gravities, skewed grade distributions and wide ranges of mineral particle sizes. Sampling practices and precautions are discussed with particular attention to each of the tripartite stages of sampling - sample acquisition, sample preparation and sample assaying. Practical examples of approaches to the sampling problem are given and some examples of significant sources of error are provided from gold and silver deposits in North America.

Jan 1, 1992

By N. M. Grant, W. G. Prast

Jamaica has extensive deposits of marble, gypsum, and limestone, offering prospects for commercial sales to nearby US markets, notably the Gulf Coast and Southeast. Stare-owned and private Jamaican industrial minerals producers have made limited sales to date but expect to increase exports during the balance of the 1980s. Restraints include Jamaican government controls on access to essential foreign exchange for new capital investments and distribution of profits. Jamaican efforts to identify market opportunities in the US are reviewed, and the outlook for further exports of carbonates is discussed.

Jan 1, 1987

By R. C. Guimareãs

Serrana's deposit contains three types of ore: oxidized, micaceous and silicate-carbonate. The results presented refer to characterization and fundamental studies performed on fractions resulting from the purification of five samples from the silicate-carbonate type collected in the mine. Each type was purified and submitted to mineralogical characterization, zeta potential determinations, and microflotation experiments. The samples, with exception of the barite, are mineralogically complex and the selectivity between apatite and gangue minerals is poor. Under the current state of art, it is impossible to feed the plant with the silicate-carbonate ore, unless it is blended with the standard oxidized ore.

Jan 1, 2002

By R. F. Shurtz

This paper uses a simple model to illustrate the fact, widely known to information theorists, that the covariogram represents only half the information in the data used to construct it. It suggests and illustrates methods of putting the other half to use in describing mineral deposits. It also identifies applications in which the phase information is not needed.

Jan 1, 1986

By R. M. Carland, F. F. Aplan

Six natural zeolites were evaluated for their ability to selectively remove heavy metal cations from solution. Ion selectivity was found to be Pb+2>Zn+2>Ni+2 and Cu+2>Co+2 from their respective solutions. The presence of K+, Ca+2 and Mg+2 in the actual waters to be used may seriously interfere with the ion exchange and elution of cations from zeolites. Zeolites were found not to be effective in removing precious metals from their cyanide solutions.

Jan 1, 1995

By A. C. T. Bigg, A. F. Colombo, A. R. MacPherson

The step-by-step study of the Stronsay ores follows the testwork through the initial determination of Bond Rod and Ball mill work indices, the MacPherson Autogenous work indices and the production of a preliminary flowsheet. These results are then used to design a pilot plant program to test the effectiveness of fully autogenous primary and secondary grinding and to determine the feasibility of controlling feed rate by the use of variable speed mill drive and/or varying the mill load. A final flowsheet is recommended with mill sizes and power requirements.

Jan 1, 1992

By J. M. Pachter

Property sales and acquisition are prominent features of today's coal industry. Before selling or buying a site, a company must know the property's economic net worth. Any evaluation of economic net worth would be inadequate if determinations of a property's environmental liabilities and costs were omitted. Short-and long-term costs can result from liabilities related to reclamation, water treatment, subsidence, and hazardous waste disposal. A structured, interdisciplinary approach can aid in the delineation, summation, and scheduling of these costs and liabilities.

Jan 1, 1987

By R. L. Wolfrom, R. Hogg, S. Chander

A gravimetric method for measuring rates of capillary rise in powders was explored. Methods to improve reproducibility and consistency of the results were investigated. In particular, the effects of particle size and packing uniformity were addressed. Studies of the wetting behavior of both spherical glass beads and irregularly shaped synthetic graphite particles by various organic liquids were carried out. Standardized procedures for bed preparation will be described. The applicability of the Washburn equation for surface energy evaluation in such systems will be discussed. Key words: Wettability, Powders, Capillary rise, Surface chemistry

Jan 1, 2003

By Lawrence A. Ph. D. Hansen, J. David Deatherage

Laboratory testing programs were conducted to investigate the performance under compression loading of several types of geomembranes and geotextiles proposed for use in heap and dump leach projects. Synthetic liners of several thicknesses were sandwiched between representative subgrade soils and cover materials, thus modeling in the laboratory the actual installation conditions expected. Performance was evaluated by visual inspection and vacuum testing. Several testing procedures and equipment were used to investigate the effect of these testing parameters on the predicted performance.

Jan 1, 1987

The authors give a corrected form of the Korobov algorithm of optimal open pit determination and describe a method of optimising the mining sequence within a preliminary pit design. A method of automatically including roadways is also given.

Jan 1, 1992

By Elza F. Burch

Feeding 600 pm X 0 raw coal to heavy media cyclones, along with the +600 pm size coal, produces an efficient separation of both the +600 pm and 600 pm X 150 pm sizes. Major advantages of the process include the elimination of desliming screens and secondary fines circuitry for cleaning the 600 pm X 150 pm size coal, and result in a very simple circuit. Incorporating four 660 mm diameter heavy media cyclones, the Providence Plant of Island Creek Corporation has operated efficiently for ten years with a magnetite consumption rate of less than 0.45 kg per ton of raw feed at a feed rate of 454 tph.

Jan 1, 1988

By Rashi Tiwari, George Danko, Jeremy Knowles

A control technique is described for enhancing the efficiency of materials handling and other mining operations. The concept involves human-operator and robotics control interactions to assist in mining operations. Many mining tasks require a human operator to coordinate the motion of several machine links by simultaneously manipulating multiple joysticks or other control devices. The new control architecture allows for automatic coordination of multiple machine joints. The machine movement may follow a computer-optimized, learned coordination pattern, while the operator still retains the master control of the overall trajectory and velocity parameters. Examples are described for a surface mining front shovel.

Jan 1, 2005

By C. M. Lundell, F. S. Kendorski, R. D. Prager

The criteria for the design of the shaft/tunnel system excavation at the Rocky Mountain Project was to provide a stable opening during and after construction to receive the concrete lining and to minimize the disturbance of the surrounding rock mass so that the rock mass resists the displacement of the tunnel mining upon internal pressurization. This paper will summarize the geotechnical design of the shaft, elbow, tunnel, bifurcations, and penstocks

Jan 1, 1986