Search Documents

By Yijun Caoa, Xiuxiang Taoc, Zhongbo Hub, Yinfei Liaoa

A new preparation scheme for a difficult-to-float coking coal from the Kailuan Mine, Tangshan, China was investigated. The results showed that grinding followed by column flotation was beneficial for obtaining products with low ash content. The positive effect of grinding on the coal floatability is attributed to the liberation of intergrowths and coal surface improvement. Tests indicated that 10 minutes was the optimum grinding time, and over grinding resulted in a deterioration in flotation performance. With a grinding time of 10 minutes, conventional flotation had potential to yield a product with around 12.42% ash content and 69.15% combustible recovery. Column flotation can reduce the product ash content to 11.15%and increase combustible recovery to 74.47%. Consistently better flotation results reveal that column flotation is more efficient than conventional flotation for such fines.

Jan 1, 2015

"For effective steel refining in the ladle (secondary steelmaking) the amount of steelmaking slag that is transferred from primary steelmaking must be limited, because the steelmaking slag contains iron oxide, manganese oxide, and phosphorus oxide. Adverse effects of slag carry-over include increased consumption of deoxidizers, phosphorus pick-up by the steel, and increased ladle refractory wear. Infrared imaging at longer wavelengths is an effective non-contact method to detect slag in the tapping stream. Various devices are used to shut off the tapping stream rapidly. These include slag darts, pneumatic slag stoppers, and slide gates for steelmaking converters, and eccentric bottom tapping for electric arc furnaces. IntroductionOxygen converters and electric arc furnaces are used for primary steelmaking. For both process types, the product (liquid crude steel) has a similar composition: largely liquid iron, with around 800–1000 parts per million (ppm, by mass) dissolved oxygen and low but significant concentrations of carbon, nitrogen, and phosphorus. The steel is tapped into a ladle, which serves as the refining vessel to adjust the final steel composition and temperature before casting.Some steelmaking slag is inevitably tapped with the liquid steel. The mass of steelmaking slag tapped with the steel is termed ‘slag carry-over’. Controlling and limiting slag carry-over from steelmaking is a primary requirement for clean steel production (Fandrich, Lüngen, and Wuppermann, 2008). Steel cleanliness refers to limiting the concentrations of dissolved impurities (such as nitrogen, oxygen, phosphorus, and sulphur) and of nonmetallic inclusions (oxides, sulphides, and nitrides) in liquid steel and in the final solid steel product. Of these, the strongest effect of slag carry-over is on the content of dissolved phosphorus in the liquid steel"

Jun 1, 2019

By E. Kapilashrami, S. Seetharaman

Refractory/metal interactions and associated reactions are significant during casting as they can lead to inclusion formation. High-temperature interactions between aluminosilicate refractories and molten steel were studied in the present investigation using the sessile drop method. The changes in the contact angles between molten iron with well-defined oxygen levels and substrates of silica, mullite (3Al2O3?2SiO2) as well as commercial refractories were measured in the dynamic mode. In all cases, the reaction led to slag formation. The experiments were performed under isothermal conditions at 1823 and 1873 K. A known and constant oxygen partial pressure was imposed above the iron drop, through appropriate CO-CO2-Ar mixtures. For all substrates, the contact angles started decreasing due to the lowering of the surface tension of iron, as oxygen was imposed on to the system. When a critical level of oxygen was reached, slag started forming at the drop/substrate interface and at this stage, the contact angle dropped suddenly. Subsequent behaviour of silica and mullite was observed to be different, with SiO2showing a non-wetting behaviour. In the case of SiO2substrate, there were also deep erosions along the periphery of the drops and there was slag accumulation at the sides of the metal drop, probably due to Marangoni flow and/or SiO(g) formation. SEM and EDS analysis of the substrates revealed that the formed slag was fayalite. The thermodynamic criteria for slag formation and possible mechanisms of the reaction are discussed in the light of the experiments. Key words: silica, mullite, fayalite, corundum, slag formation, sessile drop.

Jan 1, 2004

Published experimental data on thermodynamic behaviour of cobalt-containing slags have been reviewed and used in validating a recently developed thermodynamic model. The results from the exercise show that the model provides a reasonably good description of behaviour of cobalt in multi-component slag systems. The models for cobalt containing slags, matte and oxide solid solution phases were incorporated into CSIRO?s multi-phase equilibrium (MPE) package, which was used to calculate the equilibrium distribution of cobalt between matte and slag phases under various conditions. The results agreed well with the experimental data. Furthermore, the good agreement between the calculation and the plant data indicates that the operating conditions of industrial smelting and converting processes are close to equilibrium. Two diagrams showing the effects of slag chemistry and SO2and O2partial pressures on the distribution of cobalt between phases were generated for conditions similar to smelting and converting processes. These diagrams provide some useful guidelines for developing new strategies to improve cobalt recovery.

Jan 1, 2004

By M. Verri

[ ]

Jan 1, 2009

By G. Westcott

Impala Platinum, the second largest platinum producer in the world, is embarking on a major expansion strategy to increase its platinum output from 1.95 moz to 2.8 moz by the year 2008. The smelter complex, situated in Rustenburg, will undergo substantial modifications, and will require a solution to the capture and treatment of the smelter off-gases and dust produced during smelting and converting operations. One of the solutions explored was an integrated approach, where all the off-gases from both the primary smelting electric furnaces and the converter operations are routed to a large central gas cleaning and double catalysis, double absorption acid plant. In-line sulphur burning, utilizing a highly flexible LURO1spin cup burner with a turn down ratio of 50%, ensures that the acid plant operates independently of operating conditions at the smelter complex.

Jan 1, 2007

By A. Kondratiev

A structurally-based viscosity model for fully liquid silicate slags has been developed and applied to the Al2O3-CaO-‘FeO’-SiO2system at metallic iron saturation. The model links the slag viscosity to the internal structure of melts through second nearest neighbour bonds concentrations taken from the quasi-chemical thermodynamic model. This viscosity model describes experimental data over the whole temperature and composition ranges within the Al2O3-CaO-‘FeO’-SiO2system at metallic iron saturation and can now be applied to other industrial slag systems.

Jan 1, 2004

By X. Pan

Slag-metal equilibrium experiments were conducted at 1500ºC and 1580ºC under 0.03 atm, 0.05atm and 0.83 atm CO partial pressures using silica and Cr-oxide crucibles. The complex slags belonged to SiO2-CaO-Al2O3-MgO-FeOx-CrOxand the metal phase to the Cr-Fe-C-Si-(S)systems. The carbon saturation of the metal phase was avoided using oxide crucibles and thus the results are pertinent to ferrochromium refining slags and processes. From equilibrium data and thermodynamic calculations the CrO /(CrO+Cr2O3) ratio in the slag was determined as 0.75, 0.80and 0.86 under 0.83 atm and 0.05 atm of CO pressure at 1500ºC and 0.03 atm and CO pressure at1580ºC respectively. The results clearly demonstrated that a higher chromium content of the metal results in higher Cr in the slag, and chromium in slag decreases with increasing SiO2. The results were also sensitive to the crucibles used as these oxide crucibles saturated the slag either with respect to SiO2or Cr-oxides. It was also demonstrated that the relative amount of CrO in the slag was higher when SiO2crucibles were used in accord with thermodynamic calculations. Iso-concentration curves for carbon and chromium of the metal phase in equilibrium with the slag were drawn on pseudo ternary SiO2–(AI2O3+CaO+MgO)–(Cr2O3+Fe2O3) diagram. The activity coefficients and activities of carbon and chromium of the metal phase were also calculated from the experimental data and available thermodynamics information and were plotted as iso-activity curves in the same pseudo ternary diagram. Keywords: Chromium, slag, equilibrium

Jan 1, 2004

By E. T. Boshoff

Paper written on project work carried out in partial fulfilment of B. Eng. (Metallurgical Engineering) The weathering of kimberlite can be accelerated with cations in solution if swelling of the kimberlite occurs in contact with the weathering medium. The type and amount of swelling clays present, along with the surface charge and cation valence, determine the degree of swelling that can occur. Crystalline swelling occurs by the incorporation of cations in the interlayer spacing of the silica sheets. Kimberlite exposed to cupric cations showed very strong weathering, indicating that this type of weathering may be considered a viable process option. Kimberlite fines generated after weathering with monovalent cations showed poor settling behaviour compared to kimberlite weathered with di-, and trivalent cations.

Jan 1, 2005

By M. Tangstad, D. Lu, G. Tranell, S. Gaal, J. Safarian

The kinetics of MnO reduction from high carbon ferromanganese slag was investigated using a sessile drop technique at 1600 ºC. The effects of reductant type, ambient atmosphere and slag composition on the MnO reduction were illuminated. Two different types of industrial reductants (ground to a particle size of 44 to 106micron and pressed to pellets) were used as substrates for small slag droplets of varying composition, which were reacted in a CO or Ar atmosphere with the reaction studied in-situ. The cross sections of the reacted slag-carbon samples were subsequently studied by EPMA to find the extent of MnO reduction as a function of reaction time. It was found that the rate of MnO reduction is affected by both the type of reductant, the ambient atmosphere and the presence of metallic components in the slag. Higher reduction rates were obtained for charcoal than for coke as reductant while a CO atmosphere unexpectedly yielded faster MnO reduction than an Ar atmosphere. It was also found that metal prills in the initial slag will increase the rate ofMnO reduction.

Jan 1, 2007

By E. Munnik

The Chambishi Metals Cobalt Plant in Zambia has recently installed a novel oxidation/precipitation pressure leach process as part of the COSAC (CObalt from Slag And Copper as by-product) Project. Aniron-cobalt-copper alloy, produced by the carbothermic reduction of slag, is atomized and pumped to the COSAC Leach Plant, where cobalt and copper are recovered as dissolved sulphate salts, andiron is rejected primarily as hematite. Cobalt and copper are subsequently recovered as cathode metal in the existing Chambish ioperation by conventional electrowinning. This paper examines the challenges faced during the design and subsequent successful commissioning of the COSAC Leach Plant. The challenges discussed include alloy handling, autoclave design, autoclave cooler design, residue liquor recovery and the water balance design. Keywords: Chambishi, Avmin, COSAC, Zambia, Copperbelt, cobalt, copper, alloy handling, pressure leach, autoclaves, cooling, filtration.

Jan 1, 2003

By Dziurzyn&apos, W. ski

This article outlines the results of a computer simulation reproducing the transport of a mixture of air and methane following the outburst on 25 November, 2005 in transport gallery D-6, bed 409/4, at the ?Zofiówka? hard coal mine. Based on a mathematical model, numerical method and boundary conditions from the disturbance caused by the outburst, the Ventgraph system of computer simulation programs was adopted for the study. We performed a computer simulation of the influence exerted by the outburst on the propagation of the air and methane mixture, and compared the results of this simulation with those of the actual event as registered by sensors of the mine monitoring system. A validation of the model allowed us to present temporal changes in the concentration of methane and air along flow routes. Keywords: mine ventilation, outburst of methane, numerical simulation, monitoring system.

Jan 1, 2008

By J. P. W. Bennie, A. de Jong, G. M. Denton

Mintek together with Middelburg Steel & Alloys, developed the DC arc furnace process for the production of ferroalloys with the expressed objective of smelting ore fines (<1mm) without the need for agglomeration. In the case of ferrochrome production, the DC arc furnace, being a semi-open bath operation, loses radiant energy directly from the bath to the furnace roof and sidewalls above the melt. This energy loss is reflected in a higher electrical energy usage per ton of alloy than for a submerged-arc operation smelting lumpy ores or sintered pellets. The difference increases still further when pre-heated sintered pellet feed is used in a submerged-arc operation. This shortcoming of the DC arc furnace can however be overcome by preheating the feed to the furnace in a fluidized bed or flash reactor fuelled by cold furnace off-gas. In addition to fluidization and preheating testwork, various preheating flowsheets with associated mass and energy balances have been developed and compared from a techno-economic viewpoint. The three major advantages identified were: a) fluidized beds can preheat ores and fluxes up to 950°C without sticking and defluidizing, b) the open bath DC arc furnace does not require expensive coke or char to maintain the burden porosity and, c) the capital cost associated with the milling, pelletising and sintering plant falls away since ore fines are used directly.

Jan 1, 2004

By T. A. Ngcobo

Paper written on project work carried out in partial fulfilment of BSc Eng (Mining)degree The purpose of this report is to assess the risks faced by mines in dolomitic compartments in particular Kloof 8 shaft. The dolomites of the West Rand comprise one of South Africa?s most natural water resources, and overlie the reefs of the richest gold mines in the world. The pumping of water from the dolomitic aquifers to prevent flooding has caused the natural water table to subside, and the resulting cavities within the dolomite rock formations that overlie many gold deposits sometimes collapse, causing sinkholes. These impacts of the mining industry could worsen over time if preventative measures are not taken. This report discusses these impacts in detail, more specifically the risks to which operations in dolomitic compartments are exposed. A risk analysis was carried out to access the risks that the organization could face and it was this analysis that allowed one to examine the best methods to combat the problems. Other factors such as geological features and seismic events were also considered for the evaluation. To aid with the completion of this work various resources were utilized. A literature study was undertaken, information was gathered from various experts who specialize in dolomitic studies, evaluations were conducted and conclusions reached. The results from the project indicated that preventative measures should be implemented and correct procedures put in place to prevent any disasters.

Jan 1, 2006

By B. E. Ydstie, B. F. Lund, K. R. Løvåsen, B. A. Foss

The paper presents sensitivity analysis for a dynamic model of submerged arc silicon furnaces. The model we study, called ?Simod?, was developed by Elkem in cooperation with NTNU and Sintef. It is today a much used tool in Elkem for operator training and analysis of the dynamic behaviour of the silicon production process. The aim of our work is to bring the simulator tool closer to industrial practice, and construct a mechanism to adapt the model to the behaviour of a running process, online. The paper presents the results of the sensitivity analysis that has been undertaken for important parameters in the Simod model. The parameters associated with the process inputs are electric power loss, loss of fixed C and reactivity of carbon. The output signals that have been investigated are fed quartz, tapped silicon and silica. The paper also interprets the results of the sensitivity analysis in a process operation context.

Jan 1, 2004

By J. Lehmann, H. Gaye

A brief review of Computational Thermodynamics software concerning the modeling and prediction of reactions involving metals, slags and fluxes is presented. Their application for various steelmaking treatments is discussed. Examples concern phosphorus removal in BOF and EAF, ladle steel desulfurization, and specific treatments for inclusions control in semi-killed or Al-killed carbon and stainless steels.

By J. P. Bergh

The advent of low-quality export coal demand has brought a new range of possibilities to the South African coal industry. Products that traditionally were only of value to the domestic or combustion industry sectors now have the potential to be exported, with only minor amounts of upgrading required through beneficiation. Comparatively high steam-coal export prices can be obtained for lowquality export coal, which enhances the economic feasibility of expanding low-quality thermal coal exports. There are, however, increasing concerns about the feasibility of lower quality thermal coal exports and the broader implications. These concerns relate to the environmental impact of low-quality thermal coal production for export and the inherent threat to the security of domestic thermal coal supply in South Africa. Against this background, this paper serves to explain the extended value chain in the production of export coal. The technical and economic advantages and disadvantages of low-grade exports versus coal production for domestic use are evaluated. The value chain estimation is calculated by the beneficiation modelling and characterization of two coals. Based on the value estimation, the lowgrade export production scenario, and finally the modelling of potential pollutant distribution, are described. Keywords coal beneficiation, techno-economics, thermal coal, dense medium processing, dry processing, fine coal processing, environmental impact.

Nov 1, 2013

By J. Eriksson

Slag from stainless steelmaking is known to disintegrate, which is an environmental problem and prevents the cooled slag from being utilized. This disintegration is due to the transformation from the ßto the ? polymorph of di-calcium silicate. The transformation is accompanied by an increase in volume of about 11% and a total disintegration of the slag. AOD slag from stainless steelmaking was re-melted in a laboratory induction furnace, together with olivine and calcinated dolomite, to investigate the prevention of disintegration by increased MgO content of the slag with small changes in CaO to SiO2ratio. The modified slag was examined with X-ray diffraction and scanning electron microscopy. The trials showed that an increased MgO content can change the mineral composition towards formation of more Merwinite and Bredigite, which prevents disintegration of the slag. Keywords: slag, disintegration, di-calcium silicate

Jan 1, 2004

By L. Chen, G. A. Brooks, S. A. Nightingale

The dissolution of alumina and magnesia has been investigated using laser scanning confocal microscopy (alumina) and a rotating finger apparatus (magnesia) to assess the effects of temperature, composition and forced convection on the rate of dissolution in CaO-SiO2-Al2O3based slags. The two techniques have differing strengths and limitations, and provide complementary methods for studying dissolution. Alumina dissolution was studied for temperatures from 1477 to 1577°C. Based upon the data, the rate controlling mechanism was thought to be mass transfer control in the slag. The diffusion coefficients for the alumina particles are estimated to be in the range 10-11to 10-10m2.s. MgO degradation for sample rotation speeds of 50 to 800 rpm at 1500 and 1530°C was studied for both congruent and incongruent dissolution. The results show that the rate of dissolution for this is primarily controlled by a diffusion mass transfer mechanism for congruent dissolution except at the highest rotation speed. For incongruent dissolution, the mechanism is much more complex, with the morphology and distribution of the spinel reaction product having a significant effect. At high speeds and prolonged times, mechanical forces played a major role in the degradation process. Keywords; kinetics, corrosion, refractories, dissolution rate, inclusions, mass transfer, slags, steelmaking

Jan 1, 2004

By M. M. D. S. Vemba

Paper written on project work carried out in partial fulfilment of B.Sc. Eng (Mining Engineering) degree Engineering refers to the application of mathematics and other sciences to logically develop solutions to problems. However, in opencast mining, due to the randomness of operations, the use of mathematics is often neglected. Instead, practices that have proven successful elsewhere tend to apply. At the other end of the scale, mathematical models have been developed to identify and quantify all the operational parameters involved in the loading and haulage of ore. These are then used to optimize the operation. Optimization in this context, refers to the reduction of cost through effective utilization of the available time and resources. Considering these mathematical models, the loading and transport system at SMC (Catoca Mining Society) will be assessed with a view to its optimization. The discussion will be introduced by considering the mine background and other general information, which will highlight the main operational variables.

Jan 1, 2004