Search Documents

By A. V. Pavlov, V. A. Grygorian, Kossyrev, A. E. Semin, A. Korostylev

A new way of producing low-silicon ferrosilicon from iron-ore materials in a new type of aggregate-oxygen reactor is presented. The oxygen reactor process is based on using the calorific combustibility and reducibility of carbon materials inside the aggregate. The key to the process is successful post-combustion of carbon monoxide above a layer of a solid coke bed. Initially the possibility of production of grades of ferrosilicon containing 20 to 25% Si (FeSi20-FeSi25) was studied on a laboratory model of the oxygen reactor. Quartz sand and iron ore concentrates (from Russia and India) were used in the laboratory tests. This test work demonstrated that a ferrosilicon grade FeSi15 could be obtained directly from raw iron ore (containing 75.9 % Fe2O3 and a maximum of 23.8 % SiO2) without using rich iron-ore concentrates. The process was successfully tested on a pilot furnace at Serovsky metallurgical plant. Very promising results and efficiency parameters were achieved. The consumption of materials for 1t of ferrosilicon (15 % Si) production was as follows: 1567 kg raw iron ore, 591 kg of coal (in a composition of ore-coal briquettes), 299 kg of coke (for coke bed formation), and 815 m3 of oxygen.

Jan 1, 2004

By S W. Robertson, A Vercuil, P Craven

Mintek is currently developing a design approach for the heap leaching of low-grade primary copper sulphide material. Since the leaching of chalcopyrite requires elevated temperatures, the generation and management of heat within the heap is crucial. Furthermore, the precipitation of iron needs to be managed to prevent premature blinding of the heap, and acid consumption needs to be limited to contain cost and limit the dissolution of gangue impurities. Standard column tests using jacketed 1-m and/or 6-m columns do not allow accurate prediction of temperature changes and heat generation in an actual heap. Mintek therefore utilizes a computer model to calculate the energy balance and heat generation with time, based on the measured sulphide oxidation rates in the column. The temperature in the column is then adjusted to reflect the computer-predicted temperature in an actual heap. Using this approach, an overall copper extraction of 70% was achieved in 120 days, using 1-metre columns, when treating an ore blend containing 1.36% chalcopyrite, 0.23% chalcocite, 0.07% covellite, 3.8% pyrite and silicate gangue (92%). The chalcopyrite contribution to the total copper content in the feed was 75%. This was followed by 6-m columns using a similar approach, and the column results will be validated on a 23,000 tonne test heap. Key Words: heap; bioleach; chalcopyrite

Jan 1, 2005

By L. Forsbacka, L. Holappa

Viscosities of quasi-ternary CaO-SiO2-CrOxmelts in contact with metallic chromium were measured by the rotating cylinder method up to 1750ºC. Twelve slag compositions were selected in the composition range 20–55 wt% SiO2, 10–45 wt% CaO and 10–60 wt% CrOx. Estimation of the amounts of CrO and Cr2O3was made by regression analysis based on the earlier data. Professor Iida’s (Osaka University) viscosity model was applied and model parameters (0CrO,CrOand Cr2O3) were evaluated. The Iida model gave good consistency with the measured viscosity values.

Jan 1, 2004

By M. Le Roux

Fine coal (-500 µm) is notoriously difficult to dewater. It is not uncommon for a dewatered product to have a moisture content as high as 30 per cent after vacuum filtration. This poses several handling and financial problems to such an extent that a lot of fine coal is discarded onto slurry waste ponds. A novel way of dewatering fine coal was developed at North-West University. It entails deliberately damaging the filter cake during dewatering to allow for an increased flow of air through the cake at the expense of the applied pressure differential. This method resulted in an average improvement in final cake moisture of between 3 per cent and 5 percent when executed in the laboratory under controlled conditions. A device was designed that could be fitted onto existing belt filters that would damage the filter cake as it passes by. This device was tested on a vacuum belt filter installation at a coal beneficiation operation in the Waterberg coal field in South Africa. The results showed a 3 per cent reduction in final moisture of the cake, proving the validity of the method at full industrial scale.

Jan 1, 2012

By M. Le Roux

Fine coal (-500 µm) is notoriously difficult to dewater. It is not uncommon for a dewatered product to have a moisture content as high as 30 per cent after vacuum filtration. This poses several handling and financial problems to such an extent that a lot of fine coal is discarded onto slurry waste ponds. A novel way of dewatering fine coal was developed at North-West University. It entails deliberately damaging the filter cake during dewatering to allow for an increased flow of air through the cake at the expense of the applied pressure differential. This method resulted in an average improvement in final cake moisture of between 3 per cent and 5 percent when executed in the laboratory under controlled conditions. A device was designed that could be fitted onto existing belt filters that would damage the filter cake as it passes by. This device was tested on a vacuum belt filter installation at a coal beneficiation operation in the Waterberg coal field in South Africa. The results showed a 3 per cent reduction in final moisture of the cake, proving the validity of the method at full industrial scale.

Jan 1, 2012

By M. P. Brungs, S. Haji Amini

Static dissolution of CaO into a CaO-SiO2-Al2O3slag and slags with additional fluxing agents (fluorspar, nepheline syenite and ilmenite) was studied. The slag was packed into dense CaO crucibles and heated to 1500ºC /1600ºC. After reaction, the crucible was air cooled and cross-sectioned. The development of the Ca2SiO4 phase and concentration profiles of various cations across the reaction zone were examined by Electron Probe Micro Analysis. At 1500ºC, a Ca2SiO4layer was found to form at the CaO/slag interface. No such layer was evident at 1600ºC. Ilmenite and nepheline syenite were found to be effective substitutes for fluorspar, increasing the rate of CaO dissolution.

Jan 1, 2004

By N. Ragoonanthun

Paper written on project work carried out in partial fulfilment of B.Sc. (Mining Engineering) degree This report investigates the optimization of a raiseline in order to open up the ore reserve quicker. The project was carried out at Mponeng Mine (an Anglogold shaft formerly known as Western Deep Levels 1 Shaft and South Mine, in Carletonville). The project was divided into two focus areas namely: ?To design an optimum layout of a raiseline, which includes the scheduling of all activities for the establishment of the infrastructure. Consideration was given to the blasting practice, mining cycle, orepass placement and slusher positioning. Two designs were carried out on the above basis. ?The design of a ledging operation/practice to match the optimized layout of the raiseline. The ledging cycle design involved a thorough investigation into the possible use of drill rigs, Electronic Delay Detonators (EDD) blasting technology, longer drilled holes, Threshold Blasting (THROB),and water jet cleaning.

Jan 1, 2003

By O. F. Oxtoby, J. E. Olsen, M. W. Erwee, Q. G. Reynolds

"The extraction of molten products and wastes through smelting furnace tap-holes during the tapping process is a complex procedure involving many coupled thermophysical effects. Insight into the fluid flow behaviour in such systems can be gained by using computational mechanics tools to build highfidelity models of the fluid flow and other relevant physics. Previous work using such models indicates that the nature of the flow in the tap-hole, as well as operational parameters such as the tapping flow rate, depends strongly on the properties of the material being tapped and the geometry of the tap-hole channel. Additional complications arise when multiple fluid phases (for example, slag and metal) are present simultaneously, when porous coke beds hinder flow to the tap-hole entrance, and when the geometry of the tap-hole changes over time due to cycles of wear and repair. In the present work, challenges with the coupling of phenomena such as multiphase flow and porosity into computational fluid dynamics methods for tap-hole modelling are discussed in the context of electric furnaces used for ferromanganese production. Qualitative and quantitative results of computational models of flow through tap-holes are presented and compared as a function of material parameters to determine sensitivity effects, and in response to operational parameters to determine typical process behaviour over the duration of a tap. IntroductionPyrometallurgical production using electric furnaces accounts for substantial portion of the world supply of ferroalloys and other strategic materials (Degel et al., 2015). A range of different furnace designs may be used depending on the metallurgical process, with circular three-electrode submerged arc furnaces (SAFs) powered by alternating current being the most common for commodities such as ferromanganese and silicomanganese (Olsen, Tangstad, and Lindstad, 2007).As shown in Figure 1, manganese furnaces typically operate with a deep charge consisting of an upper layer of loose burden (onto the upper surface of which is fed solid raw material), a molten slag layer partially or completely filled with unreacted carbonaceous reductant (generally metallurgical coke), and a molten metal layer which settles to the bottom of the furnace due to its high density. The solid particles present in the slag and burden layers form porous beds which hinder the fluid flow of molten process material and gases inside the furnace (Olsen, Tangstad, and Lindstad, 2007).In order to remove material from the furnace during normal operations, a single tap-hole is built into the sidewall of the vessel near to the level of the hearth. Tapping involves removing both slag and metal phases through the same tap-hole channel, which makes tap-hole design, operation, and maintenance particularly complex. In the case of processes such as ferromanganese, which operate with no external gas injection or open arcs present at the furnace electrodes, flow of material out of the tap-hole is driven primarily by the hydrostatic pressure generated by the weight of the solid and liquid phases above the tap-hole."

Jun 1, 2019

By Stafford McKnight, Larissa Koroznikova, Steve Hall, Cameron Klutke

This paper outlines a simple methodology for mineral characterisation, developed as part of the Australian Mineral Industry Research Association (AMIRA) managed research project P777 ?The Development of Heavy Suspension Techniques for High Density Separations (Replacement of Clerici?s Solution)?. The project was sponsored by De Beers, Rio Tinto and Iluka Resources. Heavy mineral characterisation of samples arising from exploration, mining or metallurgical processes is frequently conducted using laboratory heavy liquid analysis. Unfortunately, there are only a limited number of high density (?heavy?) liquids and these tend to be more toxic as their density increases. Low-toxicity inorganic solutions, based on tungsten compounds, have been developed that can be utilised at relative densities (RD) up to 3.0. Beyond this value organic liquids can be used, however this presents significant health and safety hazards. Diiodomethane (methylene iodide) having a relative density of 3.31 is commonly used. Mixtures of thallium formate and thallium malonate were found in the early 1900?s by Clerici to provide liquids having specific gravities between 4.0 and 5.0. For the characterisation of the heavy components of mineral sand deposits (e.g. anatase RD 3.9, rutile RD 4.2, ilmenite RD 4.4 ? 4.7 and zircon RD 4.6 ? 4.8) there is currently no heavy liquid alternative to Clerici?s solution. Clerici?s solution is highly toxic and testing is now conducted by few laboratories worldwide with costs reflecting the chemical costs, infrastructure costs and health and safety regimes (e.g. blood testing of exposed staff). A simple laboratory technique of density fractionation has been developed, employing suspensions of fine tungsten carbide particles in lithium heteropolytungstates solutions, that can replace Clerici?s solution in the evaluation of fine mineral sands samples (e.g. -250 +150 microns). The developing methodology that can achieve low-cost, low toxic separations at relative densities above 4.0 is outlined and the comparison of results with Clerici?s solution presented. In addition, preliminary work on density fractionation of zircon samples is presented. Zircon fractionation relates to their inclusion, radionuclide content and metamictization.

Jan 1, 2007

By Y. Mao, D. Xie

The viscosity of TiO2-containing blast furnace slags may increase rapidly (commonly referred to as thickening) under strong reducing conditions in the blast furnace. To elucidate the mechanisms for slag thickening, measurements have been made of changes in the composition and rheological properties of TiO2-CaO-SiO2-Al2O3-MgO slags during the reduction process. The slag composition covered the range of 17–33 wt% TiO2, 9–19% Al2O3, 8–16% MgO and theCaO/SiO2from 0.8 to 1.4. The viscosities were measured using the rotating cylinder method at temperatures up to 1550ºC and the fusibility temperatures were determined from ‘breaks’ in the viscosity-temperature curves. The reduction of the slag was carried out in graphite crucibles at1500ºC for 2–6 hours The rheological properties of the slags during reduction were predominantly influenced by the slag basicity (CaO/SiO2), and the effect of other components depended largely on basic or acidic behaviour of the oxide. The reduction of TiO2in the slag by carbon was initially fast to formTi2O3, followed by further reduction to TiO and TiC. Correspondingly, the viscosity showed initially a slight decrease, followed by a gradual and then rapid increase. The thickening was found to be accelerated by an increase in TiO2content and a decrease in the CaO/SiO2in the slag. In addition to the existence of 1~3 wt% TiC, the thickened slags also had a significant amount of TiO (3~7 wt%), suggesting that TiO may play an important role in the ‘thickening phenomena’ ,possibly by forming solid solutions with TiC to significantly increase the number of solid particles in the heterogeneous slag. Keywords: TiO2slags, viscosity

Jan 1, 2004

By L. Holappa

Ferroalloys like FeCr and FeMn are mostly produced in submerged electric arc furnaces. Typical for these processes is that the amount of slag is quite high. The role of slag for the process is thus very essential and specific chemical, physical and electrical properties are required. Slags in FeCr process are Al2O3-MgO-SiO2based with minor contents of CaO and CrOx. Slags in FeMn process are principally similar originating from silicate minerals but can have quite a large composition range depending on the manganese ore and its gangue minerals. Characteristic for FeMn process is that the slag is rich in manganese oxide up to above 30%. A common feature is that the ?ore oxides?, CrOx and MnOxin slag are not only divalent oxides but also containing some higher valent of Cr3+ and Mn3+, respectively. In FeMn production conditions the slag consists mainlyMn2+. This is a clear difference from CrOx containing slags in which both two and three valent coexists in slags in FeCr process conditions. Oxidation state of the slag depends on the ambient oxygen partial pressure and temperature in the examined process. Thermodynamics of slags in ferroalloys production are discussed in terms of phase diagrams, activities and oxidation state of chromium and manganese oxides. Further, slag properties influencing reduction kinetics and furnace operation i.e. viscosity and electrical resistivity are discussed. Keywords: review, slags, ferroalloys, ferrochromium, ferromanganese, thermodynamics, physical properties.

Jan 1, 2004

By K. C. Mills

The objective of this work was to provide process engineers with values of the physical properties of various slag systems involved in high-temperature processes. Software that calculates the thermo-physical properties of slags from chemical composition is available on the www.pyrometallurgy.co.za website. This paper outlines the principles underlying the various models available in the program. The software calculates the following properties of crystalline, glassy, and liquid slags (where appropriate) as a function of temperature: heat capacity, enthalpy, density, viscosity, thermal conductivity, electrical conductivity, and surface tension. We hope, in the future, to update the program to (i) add new models as they become available, (ii) remove any ?bugs? discovered in existing programs, and (iii) provide guidance on the limitations of individual programs.

Jan 1, 2011

By L. Jeffrey

The Waterberg Coalfield has vast potential to become a significantmining and industrial centre in South Africa. Its future developmenthinges on a number of critical decisions that must be made jointly by government, power utilities and industry, and on some technical and economic challenges that must initially be overcome. Sufficient water is the primary key to enabling exploitation, together with an adequate market for the large volumes of low-grade coal. As the most likely consumer of this coal will be either a power station or a petrochemical complex, the need for additional energy will be a driving force in the development of this coalfield. Conventional mining methods can exploit the shallow coal resources in both the Grootegeluk and the Vryheid formations, but alternative technologies such as coalbed methane extraction and underground coal gasification are the only currently known technologies that may be able to exploit the deep Grootegeluk Formation resources. However, extensive research is still required into these procedures, particularly with respect to the Waterberg coals. Transport infrastructure to the region is currently not sufficiently well developed to support large-scale exploitation of the region?s coal resources. In particular, the railway line would have to be extensively upgraded to allow the increased export of coal. Alternative transport methods such as pipelines would also have to be pursued to serve a large Sasol-type petrochemical complex or coal gas extraction. The road network would also require improvement, as only the roads between the main commercial centres are currently tarred. Dr Con Fauconnier, Kumba CEO, concluded his presentation to the Investing in African Mining Conference 2004 with the words: Again, it?s all about infrastructure? when it?s there, it enables the development of bulk mining projects which attract the resultant economic benefits for the region and country as a whole. These words aptly sum up one of the stumbling blocks to the future development of the Waterberg Coalfield.

Jan 1, 2005

By Z. Zhang, R. G. Reddy

Experimental and thermodynamic modelling studies on the structure of alkali borate melts and properties are discussed. A thermodynamic structure model for alkali borate melts is developed to describe the distribution of structural groups in the alkali borate melts as a function of composition. A qualitative interpretation for the boron anomaly in viscosity has been proposed, which regards the boron anomaly as a manifestation of the various antithetical effects caused by the introduction of alkali oxide into boric oxide. It has been found that the viscosity of alkali borate melts increases or decreases according to the changes in rigidity and spatial connectivity of the glass network structure, which is the function of temperature and composition. These concepts with some key examples are discussed in relation to their usefulness and practicality in industrial slags. Keywords: alkali borate melts; structural model; activities; structural groups; viscosity;

Jan 1, 2004

By H. Ogasawara

Information on rock stress is important for safe mining in seismically active ground. On a major gold mine, a few tens of crews are continuously conducting geological drilling with small pneumatic machines. However, stress measurements are not often carried out in South African deep-level gold mines. One of the reasons is the drilling diameter that overcoring requires, which is much larger than the diameters used in regular geological drilling, e.g. Boart Longyear Metre Eater, which drills A[O] or B[O] holes. Larger diameter holes result in slower drilling advance, more load in transportation and handling at sites, and higher cost. In order to enable overcoring in BX size (60 mm diameter), we modified the compact conical-ended borehole overcoring (CCBO) technique that has been suggested by International Society for Rock Mechanics (ISRM) and was originally designed for NX drilling (76 mm diameter). With a single overcoring, the 3-D stress tensor can be determined. We tested this modified method at a depth of about 3 km at Moab Khotsong mine in South Africa. We worked with drilling crew who usually work at geological drilling with the Metre Eater. In January 2011, we tried using regular geological drilling tools (a sequence of a normal BX bit, reamer, and rod) without success. In August and September 2011, introducing stabilizers and thin BX bits, we succeeded. We could complete a cycle of procedures necessary for an overcoring, including shaping the borehole-end conically, glueing a 16-element strain cell, and overcoring, within 2.5 hours. Only 10 cm overcoring is needed, which increases the chance of successful overcoring in heavily fractured conditions. This modified method is suitable for up-dip holes to depths of 10-15 m from tunnels, and has the potential to be widely used at the initial stage of geological exploration drilling at many localities.

Jan 1, 2012

By M. Somerville, S. Sun

The liquidus temperature and viscosity of a range of melter slags produced in South Africa were determined. Drop-quench experiments were carried out on the supplied plant samples to determine the liquidus temperature and phase relations at sub-liquidus temperatures. The temperature measurement range covered 1300°C to 1630°C. Results from these experiments show liquidus temperatures for the melter slags to be in excess of 1500ºC with the chromium containing spinel as the primary crystalline phase. At lower temperatures, an olivine or pyroxene phase co-existed with the spinel phase. The viscosity of the slags was determined over a temperature range of 1350 to 1550°C, under a controlled atmosphere. Results show two orders of magnitude variation in the viscosity (0.2 to 20Pa s) with strong effects of slag chemistry and temperature. Slags with lower SiO2and Cr2O3concentrations were more fluid. Slags with the lowest FeOx and highest SiO2concentrations were the most viscous. These observations are in accord with general behaviour of silicate slags. While the presence of a spinel phase may have an effect on the viscosity of the melter slags, results obtained to date indicate a much stronger effect due to the presence of an olivine or pyroxene phase at lower temperatures. Keywords: phase equilibria, liquidus, viscosity, slags, olivine, spinel, pyroxene

Jan 1, 2004

By A. J. Van Der Merwe, J. F. Erasmus

One of the valuation approaches applied to Advanced Exploration Areas and Pre-Development Projects is the so-called ?in situ Mineralization Method? or the ?Yardstick Method?. This method is based on the concept of a known undeveloped Mineral Resource being worth a certain fraction (the ?Yardstick?) of the contained commodity value (?metal in ground?), using commodity prices ruling at the date of valuation. The Yardstick value is derived usually from an average market-based figure obtained from an analysis of recent transactions and is expressed as a monetary value per ounce or per tonne. It maybe modified to accommodate the quality (e.g. grade) and category (e.g. confidence level) of the Mineral Resource/Reserve involved and the time, effort and expenditure expected to be involved in bringing the project to fruition. Some eighteen recent and relevant transactions were analysed, allowing the following general conclusions to be reached: ? a Yardstick with which to value undeveloped PGE mineral resources is likely to range between 0.5% and 2.5% of the in-ground contained metal value ? the expected method of mining (especially with regard to mining costs) and the grade of the mineralization both have a strong influence on the Yardstick ? the status (classification) of the Mineral Resource has some influence on the Yardstick and ? the ruling price of platinum and the regional location of the deposit appear to have insignificant influences on the Yardstick.

Jan 1, 2006

By R. Zivojinovic, S. Vujic, T. Tanaskovic

The problem of determining the optimum exploitation life of machinery, namely the optimum time for machinery and equipment replacement, represents a complex and highly responsible engineering task. Taking into consideration the situation prevailing at coal pit mines in Yugoslavia, the tasks of this class are very complex and difficult. To make a decision on replacement of capital equipment and machinery, such as bucket wheel excavators within the mentioned systems, understands a management task of utmost responsibility. It requires high professional and analytical knowledge as well as the reliable arguments, based on multidisciplinary professional approach. In this paper, the authors present their views on the problem of establishing the optimum exploitation life of bucket wheel excavators, offering an algorithm, based on dynamic programming, as a solution. Keywords: Bucket wheel excavators, exploitation life of machinery, optimization, operations research, theory of replacement, dynamic programming

Jan 1, 2003

By T. Watanabe, S. Hayashi, M. Hayashi, K. Nagata, H. Fukuyama

Chemical states of fluorine in CaO-SiO2-CaF2glasses in a composition range of CaO/SiO2=0.5?1.3 and 5?25 mol%CaF2have been investigated by 19F solid-state NMR with and without MAS. The isotropic chemical shifts of the glasses are close to those of cuspidine crystal (59.4 and64.3 ppm with respect to C6F6) and CaF2crystal (58.6 ppm). The fluoride ions are coordinated with four or less than four calcium ions in this composition range. The chemical shifts move to the lower frequency with an increase in the CaF2content, whereas those are not affected by theCaO/SiO2ratio. The ionic distance between calcium and fluoride ions increases with an increase in the CaF2content. The chemical state of fluorine is not disturbed by the degree of polymerization of the silicate network. Comparing the MAS and static NMR spectra, the second moment attributed to 19F-19F dipole-dipole interaction has been estimated. The values of the glasses range over 3.1?7.3107Hz2andthose are larger than the calculated value of cuspidine crystal. This indicates that fluoride ions form Ca-F clusters in the glasses and that the size of clusters increases with increasing the CaF2content. Keywords: chemical state of fluoride ion, CaO-SiO2-CaF2glass, solid state 19F NMR spectroscopy

Jan 1, 2004

By C. Wade, A. Swart, M. Dworzanowski

AngloGold Ashanti operate a pyrite flotation plant at their East Gold Plant, Acid Plant and Flotation Plant (EGAF) metallurgical complex within their Vaal River operations in the North West province in South Africa. The flotation plant feed is reclaimed pyrite rich tailings and the concentrate produced is used as the source of sulphur for the EGAF acid plant. The sulphuric acid produced is in turn used for the recovery of uranium at the Vaal River South uranium plant. The original flotation plant built in 1960 was based on the use of many small volume flotation cells and was becoming very expensive to operate and its age severely limited further operation. A decision was taken in 2005 to replace this plant with a new one based on fewer, larger volume flotation cells. This paper describes the benefits of using larger volume flotation cells in this new flotation plant when compared to the smaller volume flotation cells in the old plant. The benefits of the new plant include a smaller plant footprint, fewer flotation cells, fewer pumps, no distribution boxes, simpler piping, a greater flotation volume and a reduction in installed power. The saving in capital cost could not be quantified because of the age of the old plant. The savings in operating cost will arise from fewer operators, less maintenance and reduced power consumption. The new plant has not been in operation long enough to quantify the benefits in operating cost and metallurgical performance. However, recovery improvements can be expected given the greater flotation volume (increased residence time) and the installation of larger, more efficient flotation cells.

Jan 1, 2007