Search Documents

By J. A. L. Napier

It has been established that significant time-dependent stope convergence may occur over time periods of hours and days in certain hard-rock gold and platinum mines. The source of this time-dependent behaviour appears to be associated with both pre-existing discontinuities and with mining-induced fractures that form near the stope face. These induced fractures may be associated with blasting processes and may also be formed in response to high stress concentrations in the unmined regions immediately ahead of the stope face. In shallower platinum mining operations, time-dependent behaviour is, however, observed to be much less marked unless some form of specific mining-induced fracturing occurs. One particular case of considerable interest is the time-dependent behaviour that is found to be associated with the formation and deployment of crush pillars. The purpose of the paper is to present a simple limit-equilibrium computational model of this behaviour that is sensitive to both the formation sequence and the size of planned crush pillars in a mine layout. This model provides a useful means to optimize the sizing of crush pillars, and at the same time may be used to identify potentially hazardous circumstances in which pillars may not crush in a stable manner.

Jan 1, 2012

By D. B. Paterson

In view of decreasing head grades, the relatively high gold price, and recent developments in metal evaluation, an exercise was initiated to determine the extent of gold concentration, the mode of occurrence, and the areas of concentration within the run-of-mine milling circuits of Randfontein Estates Gold Mining Company (Witwatersrand) Limited. The total gold content of three of the thirteen run-of-mine mils in the Group was measured as a typical lock-up of approximately 200 kg per mil. The majority of this gold was concentrated either behind the grid-type body liners or within the pockets of the body liners. This paper is an account of the experimental procedure and the results obtained, and highlights possible means of limiting gold lock-up in future.

Jan 1, 1988

The current methodology to design stope support systems in South African gold and platinum mines is based upon the tributary area concept. The discontinuous nature of the hangingwall rock is not adequately addressed, and mechanisms leading to rock mass failures between adjacent support units are poorly understood. The work reported here aims to formulate a basis for quantifying support mechanisms and gain insights into the influence of rock discontinuities on stable hangingwall spans. Numerical models are used to qualitatively investigate the stress transfer from the support units to the discontinuous hangingwall. Stable hangingwall spans are quantified by considering two failure mechanisms, namely (i) beam buckling, and (ii) shear failure due to slip at the abutments. The output of the proposed design methodology is appropriate site specific support spacing, based on discontinuity spacing and orientation. The method is particularly suited to mines at intermediate and great depth, where typically the hangingwall is highly discontinuous due to face parallel mining induced fractures. Results of parametric studies show that with increasing in situ compressive hangingwall stress, beam thickness and friction angle, hangingwall stability is increased, leading to wider stable hangingwall spans between adjacent support units.

Jan 1, 2000

By J. Kirsch

Keywords: Pyrometallurgy, pneumatic transport, pneumatic transport Dense-phase pneumatic injection has begun to replace more traditional furnace-feeding systems. The paper describes the technology as it is applied to processes where the back pressure at the point of injection is greater than 50 kPaG. It reviews earlier systems of injection and more recent developments that address concerns for instantaneous control in modern smelters. The new technologies fall into two groups, (1) modified pressure-difference control (sub-divided into simple and complex) and (2) mechanical-feeder-based control. Features of current injection systems include feed splitting in two forms, passive and active, and co-current injection.

Jan 1, 2006

By B. G. Russell

A wide range of minerals is found within the Republic of South Africa, many of which are exploited to a greater extent than in similar deposits found elsewhere. It is often asked whether this is atributed to the high grade of the ores encountered in this country, or whether such factors as fiscal and Infrastructural incentives create an economic climate that has en bled the mining industry to successfully extract and market minerals at a profit. This paper views South Africa's mineral resources in a regional and global context In an attempt to place the country's geological wealth in perspective. It represents the author's own Views, and not necessarily those of the Department of Mine al and Energy Affairs.

Jan 1, 1986

By D. F. Malan

This paper presents an overview of work conducted over several years to investigate the continuous stope closure profiles recorded in tabular excavations and the use of this data as a hazard indicator. In spite of the brittle nature of the rock, measurements in gold mines and intermediate depth platinum mines revealed a significant time-dependent closure component. Various approaches to simulate the time-dependent closure have been investigated. Viscoelastic theory is able to simulate the time-dependent closure behaviour, but there are subtle problems with the use of this theory as it cannot simulate the failure processes in the rock. To overcome these problems, continuum and discontinuum elasto-viscoplastic models were developed by the authors. Discontinuum models have the advantage of being able to simulate the creep behaviour of prominent discontinuities. Development of these models has led to useful insights into rock mass deformation and has made the numerical simulation of parameters, such as rate of mining, possible for the first time. A number of practical applications for the mining industry have been developed from this study. Among these are the delineation of geotechnical areas using closure data, use of the data as a hazard indicator and to give warning of large collapses in the platinum mines, identification of areas to be preconditioned in the gold mines, measurement of the effectiveness of preconditioning and improved da

Jan 1, 2007

By J. Trckova, P. Prochazka

Physical models from equivalent materials satisfying geometrical and physical similarity have been constructed. A special technology of simulating the excavation of an opening at the front part of a tunnel and of measuring the deformation at the tunnel face was applied. The results yielded by the physical models were used to formulate constitution relations in the numerical solution. This coupled modelling enables us to predict the behaviour of tunnel structures more accurately. On a construit des modèles physiques, réalisés en matériaux équivalents et répondant aux conditions de ressemblance géométrique et physique. Sur ces modèles, on a utilisé une technologie intéressante de simulation du forage du tunnel et de la mesure de déformation du front de taille pendant le forage en progression. Les résultats donnés par les modèles physiques ont été utilisés pour formuler les relations de constitution dans la solution numérique. Une telle construction de modèles combinés permet de prévoir plus précisément le comportement de la structure du tunnel. Es wurden physikalische Simulierungsmodelle aus äquivalenten Werkstoffen konstruiert, welche die Bedingungen der geometrischen und physikalischen Ähnlichkeiten erfüllen. Bei diesen Modellen hat man die interessante Simulationstechnologie des Tunnelvortriebs sowie die Verformungsmessung beim Tunnelabbaustoß während des Vortriebsvorgangs eingesetzt. Die Ergebnisse der physikalischen Simulation wurden zur Formulierung von Konstitutionsrelationen in der numerischen Lösung genützt. So eine kombinierte Simulation erlaubt eine genauere Prognose des Benehmens der Tunnelstruktur.

Jan 1, 2003

By M. Ghoreychi, X. Daupley

ABSTRACT: The paper is devoted to two major aspects related to the abandonment of salt mines: 1)- Long-term risk associated with the mechanical instability of surface and its consequences for public security and properties. 2)- Long term dissolution and transport of salt resulting from its communication with groundwater. Basic characteristic features of salt deposits and mining methods are presented through the studies already undertaken on French mines. This analysis allows to identify major hazards encountered in different traditional salt mines and solution-mining cavities. In particular, the role of overburden (presence and thickness of salt layer in exploitation roof, presence of clayey rocks or hard rocks e.g. dolomite or anhydrite), presence of water-bearing strata and possibly natural brine levels, discontinuities, etc. are discussed. In the second part, the main features of mechanical behaviour of salt (creep, damage) as well as transfer processes of this material are presented. The influence of these aspects on the long term evolution of abandoned salt mines is then analysed. KEY WORDS: exploitation, abandonment, salt, mechanical, stability, transport, solution, brine. ZUSAMMENFASSUNG: Der Artikel bezieht sich auf zwei bedeutende Aspekte beim Salzabbau: 1)-Das langsfristige Risiko zur Bodenoberflächeunbeständigkeit und sein Einfluss über Mensch= und Gütersicherheit. 2)-Die langsfristige Auflösung und Beförderung des Salz beruhen sich auf Studien über französiche Bergbauen. Diese Analyse emöglicht es, die bedeutendesten Risiken in verschiedenen Salzgruben zu identifizieren, bzw. Traditionellen oder durch Auflösung abgebauten. Insbesondere wird die Rolle des Deckgebirges (Vorhandensein und Dicke von Salzschicht am Dach des Grube, Beisein von Tanlager oder hartem Gestein wie Bitterkalk oder Anhydrid), Beisein von wasserhaltigem Boden und/oder gesalzenen Wasserflächen, Trennflächen, usw… erötert. Im zweiten Teil werden die haupsächlichen Eigenschaften des Salzverhaltens (Kriechen und Beschädigung) beschrieben. Ihr Einfluss über das Verhalten von stillgelegten Bergwerken lässt sich analysieren. SCHLÜSSELWÖRTER: Bergwerksbetrieb, Stilllegung, Mechanik, Beständigkeit, Ausbreitung, Aussolung, Solewasser. RESUME: L’article est consacré à deux aspects majeurs liés à l’abandon d’exploitations de sel : 1)- Le risque d’une instabilité à long terme de la surface du sol et son incidence sur la sécurité des personnes et des biens. 2)- La dissolution à long terme et le transport de sel sous l’effet d’une communication avec des eaux souterraines. Les principales caractéristiques de gisements et d’exploitations de sel sont présentées en s’appuyant sur les études antérieures réalisées sur les exploitations en France. Cette analyse permet d’identifier les risques majeurs rencontrés dans différentes mines de sel traditionnelles ou exploitées par dissolution. En particulier, le rôle du recouvrement (présence et épaisseur d’un banc de sel au toit de l’exploitation, présence de terrains argileux ou de roches dures telles que la dolomie ou de l’anhydrite), présence de terrains aquifères ou de nappes salées éventuelles, discontinuités, etc. sont discutées. Dans la deuxième partie, les principaux traits du comportement mécanique du sel (fluage, endommagement) ainsi que les processus de transport de ce matériau sont présentés. L’influence de ces aspects sur le comportement à long terme d’exploitations abandonnées de sel est ensuite analysée. MOTS CLES: exploitation, abandon, mécanique, sel, stabilité, transport, dissolution, saumure.

Jan 1, 2003

By C. Tan, C. Detournay

Wellbore stability is a major concern for drilling in naturally fractured formations. The infiltration of drilling mud into the fractures is a factor, which may compromise wellbore integrity due to the loss of strength experienced by the fractures. The reduction in the fracture frictional and cohesive properties is attributed to weakening of the infill materials and lubrication of fracture asperities by the mud filtrate. One way to investigate the influence of mud infiltration on wellbore stability in fractured formations is to use a numerical modeling approach. A requirement for the numerical model is the ability to predict the region of mud infiltration. This paper describes a numerical technique to model the extent of mud infiltration for application in coupled fluid-mechanical simulations in densely fractured rock masses using the computer code, UDEC. Several factors are considered including fracture pattern, in-situ stresses, reduction in joint frictional angle and cohesion, viscosity of the mud filtrate and fracture plugging. Results of numerical simulations are presented to illustrate the technique and show the influence of these factors on the extent of mud infiltration. Un des problèmes importants posés par le forage en milieu fissuré saturé, est celui du maintient de la stabilité du puit. L’infiltration de boue de forage dans le massif peut avoir pour effet de réduire les propriétés frictionnelles et cohésives des fractures et de compromettre ainsi la stabilité du puit de forage. Le radoucissement des propriétés des fractures est attribué à la dégradation du materiau de remplissage et au pouvoir lubrifiant des boues. L’analyse numérique offre un moyen d’investiguer l’influence jouée par l’infiltration de boue sur la stabilité du puit. Un des critères de sélection du modèle numérique sera son pouvoir de prédiction du domaine d’infiltration de boue. Cet article décrit une technique numérique permettant de modéliser l’infiltration de boue de forage dans le cadre de simulations hydro-mécaniques, en milieu à haute densité de fractures, effectuées avec le logiciel de calcul UDEC. Parmis les facteurs tenus en compte, on trouvera la nature du réseau de fractures, les contraintes in-situ, le radoucissement en friction et cohésion des joints, la viscosité de la boue et le bourrage des fractures. Des résultats de simulations sont présentés pour illustrer la technique et montrer l’influence de ces facteurs sur la taille du domaine d’infiltration de boue. Bohrlochstabilität ist ein wichtiger Aspekt für das Bohren in geklüfteten Gebirgsformationen. Das Eindringen der Bohrlochstützflüssigkeit in die Klüfte kann die Bohrlochintegrität wegen des Verlustes der Festigkeit des Kluftsystems gefährden. Die Reduktion der Reibung und kohäsiven Eigenschaften ist der Schwächung der Kluftfüllung und der Schmierwirkung der eingerungenen Stützflüssigkeit in Bezug auf die Kluft-Asperities geschuldet. Numerische Berechnungen sind ein Weg zur Untersuchung des Einflusses der Infiltration der Bohrlochstützflüssigkeit auf die Bohrlochstabilität in geklüfteten Gebirgsformationen. Eine Voraussetzung für numerische Modelle ist die Fähigkeit den Bereich der Infiltration der Stützflüssigkeit zu prognostizieren. Diese Publikation beschreibt ein numerisches Verfahren, um die Reichweite der Infiltration von Stützflüssigkeiten mittels fluid-mechanisch gekoppelter Simulationen im engständig geklüfteten Gebirge mit dem Programm UDEC zu modellieren. Verschiedene Faktoren, wie Kluftmuster, Gebirgsspannungszustand, Reduktion von Kluftreibungswinkel- und kohäsion, Viskosität der Stützflüssigkeit und Rissabdichtung wurden untersucht. Ergebnisse numerischer Simulationen werden präsentiert, um die Vorgehensweise zu illu

Jan 1, 2003

By H. T. Chiwaye

Risk analysis is an important step in the design of rock slopes in open pit mining. Risk is defined as the product of the probability of slope failure and the consequences of the failure, and is generally evaluated in terms of safety and economic risk. Most of the risk analysis done at present is based on the use of limit equilibrium (LE) techniques in evaluating the probability of failure (POF) of the slopes. The approach typically makes use of full Monte Carlo simulations of the limit equilibrium models, with all uncertain variables randomly varied. The number of required simulations is generally over a thousand, at times as high as 20 000, in order to produce statistically valid results of the POF. Such an approach is clearly not practical when using numerical modelling programs dueto the high computational effort required. This paper explores the impact of using numerical modelling instead of the traditional LE techniques in evaluating the probability of slope failure. The difference in the overall assessed risk, in terms of economic impact, for the mining operation is then evaluated. With numerical models, approximate methods are used in the calculation of the probability of failure instead of full Monte Carlo simulations. This paper will use a method called the response surface methodology (RSM) for estimating the POF from numerical analyses. Simple slope models were used to verify the accuracy of the RSM method by comparing the results with those obtained from full Monte Carlo simulations. It is shown that there is good agreement between the POF values computed using full Monte Carlo simulation and those obtained using the RSM method. Finally, the use of numerical modelling in the assessment of risk is shown to bring a significant difference in the result compared with that from LE methods. One of the reasons for the difference is that LE models tend to underestimate the failure volumes and hence the consequences of slope failure.

Jan 1, 2010

By M. K. Sichone

Anglo Platinum?s Waterval smelting complex based in South Africa operates the Anglo Converting Process (ACP) that produces SO2 offgas. This SO2 offgas is treated in a double-contact, double-absorption acid plant allowing for conversion efficiencies higher than 99.90 %. The catalytic converter used in the acid plant to convert the SO2 to SO3 is a 4-bed reactor loaded with a combination of cesium-promoted and conventional vanadium pentoxide catalysts. In June 2008 there was a shutdown, in which one of the main activities was to screen the catalyst. Before this shutdown, the operator would control the converter pass temperatures manually, via the SCADA, especially during plant start-ups after which some of the automatic temperature controllers were used. After the shutdown, the control philosophy was revisited and all temperature controllers were put on auto mode during plant start up. Furthermore the set points of the pass inlet temperatures were reduced to maximize conversion in the first two passes. The result has been a reduction of SO2 emissions, from a daily average of 50 ? 70 ppm to as low as 20 ppm for similar sulphur dioxide and oxygen concentrations. Further work has been done to maintain high bed temperatures in the third and fourth passes at low SO2 strengths by splitting the gas stream between pass 1 and 2 thus increasing the SO2 content in the gas to pass 2. This increases the temperature of the gas exiting the second pass, which results in higher temperatures in passes 3 and 4. Comparison of the converter performance prior to and after the changes is made. The benefits of partially bypassing the first pass to increase the SO2 content in the gas to the second pass are shown. Conclusions and scope for further work have been drawn from the comparisons.

Jan 1, 2009

By A. Feather

The Minataur? Process (Mintek Alternative Technology for Au Refining) is a novel route for the production of high-purity gold using solvent extraction. Following the successful demonstration of the process on a pilot-plant scale, a full-scale 24 t/a production plant has been commissioned at Harmony Gold Mine in Virginia, Free State. The commercial implementation of this process represents not only a significant advance in gold-refining technology, but may be instrumental in initiating important changes in the legislation regulating the marketing of gold in South Africa. Gold of either 99.99% or 99.999% purity can be produced from intermediate process products having a wide range of gold contents. The process comprises oxidative leaching of the solid feed, followed by selective solvent extraction of the gold from the leach liquor to reject impurities, and precipitation of high-purity gold powder. This paper outlines the process, presents selected results of two pilot-plant trials in which 5 kg/d of high-purity gold was produced from silver-refining anode slime and gold-electrowinning cathode sludge, and provides some details of the cost benefits.

Jan 1, 1997

By B. Simser

At Brunswick Mine, an increase in the number of seismically-related falls of ground and in particular rockbursts occurred during 1999. This was due to the ever-increasing stress levels in the remaining ore reserves, mining in difficult highly stressed areas and in particular troublesome geological features. In conjunction with the Noranda Technology Centre, development of rockburst support systems started at the Brunswick Mine in 1996 and efforts were accelerated in 1999. A support package consisting of #6 gauge chain link mesh, #0 gauge heavy mesh straps, and a 1 m by 1 m pattern of modified conebolts was developed. The conebolts were modified to enable mixing of the resin anchoring. Two major rockbursts occurred during an intense seismic episode at the Brunswick Mine from October 13th to 17th , 2000.The area was evacuated approximately four hours before the first burst hit, and remained closed during the seismic ?flurry??. The first damaging activity occurred around midnight on Friday the 13th, and a second damaging episode occurred on the 17th that included a local Richter Magnitude 2.7 event. The second rockburst had dimensions of approximately 5 m by 5 m by 20 m or 2150 tonnes of massive sulphide material (density 4300 kg/m3). The first failure area was more extensive, caving approximately six metres of an intersection back with the lateral extent not safely measurable. This paper briefly describes the mining conditions that led to the bursting, the seismic response of the region, the mechanisms thought to have caused the bursts, and a yielding support system which had been partially installed before the burst.

Jan 1, 2002

By R. Drummond

The fourth Teetered Bed Separator (TBS) has just been installed in Australia, and trials have been run in many sites. There is a growing recognition of the potential advantages of using TBS technology to treat coal in the ?3+0.25 mm size range, at cut points below 1.60. From these activities, there has been a substantial growth in knowledge with respect to application engineering and operational functions. The paper briefly describes the installations, including flowsheets, and so provides a background to the potential deployment of TBS technology. There are a large number of potential applications for TBS technology, including treatment of fine ROM coal in new plants, or in upgrade situations for re-processing of spiral product, or scavenging coal from coarse tailings. As well, cost effective capacity upgrades are possible by using TBS units for treating the sands size fraction. Issues arising from Australian TBS installations and application engineering are also discussed.

Jan 1, 2002

By S. Fletcher, C. Calle, K. Constanti-Carey, R. Ruzbacky, M. D. Horne

Laboratory test-work has established that two classes of redox catalysts based on anthraquinone and bipyridinium derivatives are effective in accelerating the rate of removal of metallic iron from reduced ilmenite (RI) in the aeration step of the Becher process. Two water-soluble anthraquinone derivatives are efficient: 9,10-anthraquinone-2,6-disulfonicacid, disodium salt (catalyst AQ-2,6) and 9,10-anthraquinone-2-sulfonic acid, monosodium salt(catalyst AQ-2). When 0.2 per cent w/v of either was added during aeration the rate of metalliciron removal was accelerated by two to three times. Furthermore, the addition of either compound resulted in magnetite (Fe3O4), the iron oxide phase preferred in commercial practice, being formed. However, both AQ-2,6 and AQ-2 were rapidly lost from solution during aeration although their catalytic activities persisted even when their concentrations in solution were low(<0.05 per cent w/v). The negatively charged anthraquinones were lost from solution most probably by adsorption onto the magnetite that has a net positive charge at the pH values encountered during aeration. To address this problem, the catalytic activities of positively charged bipryridinium derivatives were tested. Two water-soluble bipyridinium compounds, paraquat (1,1’-dimethyl-4,4’-bipyridinium dichloride) and diquat (6,7 dihydrodipyrido [1,2-a:2’,1’-c] pyrazinediiumdibromide), were found to significantly accelerate the rate of removal of metallic iron from reduced ilmenite, and both gave magnetite as the oxide product in the laboratory tests. Moreover, recycle tests showed they were not lost from solution as quickly as were the anthraquinone derivatives. Results in larger scale plant laboratory reactors also showed a significant increase in aerationrates when diquat was added and magnetite was again the oxide formed. However, the oxygensupply to the reactors was insufficient to achieve the maximum effect of the catalysts on theaeration rates. The limited supply of oxygen in a full scale aerator may prevent the application ofthe catalysts in a commercial Becher operation. Keywords: Becher process, aeration, anthraquinone, bipyridinium, redox catalyst, reduced ilmenite

Jan 1, 2003

By F. B. Samani, B. Stabel

The 1,000 MW Hydro Power Station Masjed-e-Soleiman (formerly called Godar-e-Landar) in Iran is under construction since 1992. The rock engineering aspects of the major underground structure, i.e. the powerhouse cavern shall be reported on in detail. The geotechnical investigations are described and results given. The results of several geotechnical analyses are presented. The designed and executed rock support is given. A description of the monitoring systems and typical measurement results obtained during and after excavation are presented. The lessons learnt during construction of the Stage-I powerhouse cavern were applied on the extension of the powerhouse cavern, which is to house an additional 1000 MW. Details regarding the unexpected behaviour of the Mudstones are given. Die 1000 MW Wasserkraftanlage Masjed-e-Soleiman (vormals Godar-e-Landar genannt) befindet sich seit 1992 in Bau. Dieser Artikel berichtet im Detail über die felsbaulichen Aspekte der Untertagebauwerke, insb. der Maschinenkaverne. Die geotechnischen Untersuchungen werden beschrieben und deren Ergebnisse wie die Ergebnisse verschiedener Berechnungen werden präsentiert. Die geplante und die ausgeführte Felssicherung wird angegeben. Die eingebauten Überwachungseinrichtungen werden beschrieben und typische Ergebnisse während des Aushubs und danach werden dargestellt. Die Erfahrungen beim Aushub der Kaverne der Stufe I wurden beim Entwurf der Kaverne der Erweiterungsstufe II, die weitere 1000 MW beherbergen wird, berücksichtigt. Details zum unerwarteten Verhalten des Schluff-/Tonsteins werden angegeben. La centrale hydroélectrique de Masjed-e-Soleiman (dénommée anciennement Godar-e-Landar), d’une puissance de 1.000 MW, est en construction depuis 1992. Un rapport détaillé sera présenté sur les aspects relatifs à la construction en enrochements de l’aménagement souterrain principal, à savoir la caverne abritant la salle des machines. Une description des investigations géotechniques réalisées y est fournie ainsi que les résultats correspondants. En outre sont présentés les résultats de plusieurs analyses géotechniques. L’ancrage dans la roche tel que projeté et réalisé est présenté. Une description des systèmes de contrôle ainsi que les résultats de mesures typiques obtenus au cours des travaux d’excavation sont donnés. Les leçons tirées lors de la construction de la Phase 1 de la caverne de la salle des machines furent appliquées à l’extension de la caverne de la salle des machines, qui doit abriter une unité supplémentaire d’une puissance de 1.000 MW. Par ailleurs, des détails sont donnés sur le comportement inattendu des argilites.

Jan 1, 2003

By J. L. Fuentes-Cantillana, Á. Rodríguez, P. Morillo

Evacuation operations from work places in the case of an emergency are the key to minimising the effects of catastrophic type accidents such as fires, explosions, cave-ins, floods, etc. The correct planning of these operations, having the necessary means for sounding alarms and communicating and suitable training of personnel are the key factors for guaranteeing successful evacuation. The article gives an analysis of the problem in the case of subterranean mining and various types of work developed by AITEMIN in this field, including the development of new alarm and communication means specially adapted to the characteristics of mining operations, development of tools for help in the preparation of emergency plans and experiences in the education and training of personnel.

Jan 1, 2003

By I. Cerny, M. Vanek, J. Hubácek

"SWOT analyses and the closely related TOWS matrix are frequent starting points for an organization to develop its strategy. The paper deals with the evaluation of the TOWS matrix and presents three novel approaches to evaluate the different factors of the TOWS matrix, namely (1) approach to evaluate the factors with identical weights; (2) approach to evaluate factors with their weights determined within the different quadrants of the TOWS matrix; and (3) approach to evaluate factors with weights determined within the whole TOWS matrix. The third approach has two variants. The proposed approaches to evaluate the TOWS matrix were tested on a SWOT analysis of a significant mining company in the Czech Republic. The results imply that the strategy W-T (weaknesses-threats) is recommended in three cases, while the strategy S-T (strengths-threats) is recommended once. The paper may be valuable for managers responsible for strategic planning.IntroductionThe process of human needs gratification has been closely connected with raw material resources of the planet. In the contemporary socio-economic conditions, the task of the mining company managers, apart from extracting mineral resources, is to meet the owners' intents.The managerial work itself becomes very complex. In mining companies in particular, the complexity is augmented by the characteristics of the business. Undoubtedly, the key factor is that mineral resources cannot be renewed or relocated. Stojanovi (2013) characterizes mining projects as involving great investments in finance and time, as well as consecutive decisions and a 'complex mosaic of numerous unknown factors that affect the value of the project'. He adds that mining projects are typified by a 'number of geological, technological, technical, economic, environmental, social, and financial risks' (Stojanovi , 2013).Inter alia, the managerial work may also be intese due to the dynamic internal and external conditions for the existence of any company (Vane? k, 2014). This tallies with Peter Drucker’s prediction in 1969; that the times at the turn of the millennium could be expected to be turbulent (Drucker, 1969)."

Dec 1, 2018

By Carl Havemann

[PAPER PRESENTED AT THE 8thINTERNATIONAL CORROSION CONFERENCE HELD AT THE SA NATIONAL MUSEUM OF MILITARY HISTORY, SAXONWOLD JOHANNESBURG DURING 14-15 NOVEMBER, 2006.]

Jan 1, 2006

By M. W. Hildyard, M. O. Kataka

Seismic integration schemes aim to incorporate the rock mass response provided by the historical seismic activity to improve the ability of numerical models to reproduce future response to mining. Up to now, integration schemes considered the events using quasi-static models. This paper presents case studies that consider some of the seismic and modelling issues needed to extend these schemes to include the dynamic characteristics of seismic events. The ultimate aim of an automated integration scheme seems impractical for dynamic modelling. The predictions of the WAVE elastodynamic finite difference program are, however, suitable for modelling limited numbers of events to determine either the near-field velocities and damage or the effect of fractures and excavations on the far-field low frequency response. Les projets d’intégration sismique ont le but d’incorporer la réponse de la masse rocheuse à l’activité sismique historique pour améliorer la capacité des modèles numériques à reproduire la réponse future à l’exploitation minière. Jusqu’à présent, les projets d’intégration étudiaient les évènements avec des modèles quasi-statiques. L’étude présente révèle des études de cas qui considèrent certaines des questions concernant modelage et séismes qui sont nécessaires pour porter plus loin ces projets en incluant les caractéristiques dynamiques des évènements sismiques. Le but final d’un projet d’intégration automatisé semble impraticable pour la modélisation dynamique. En revanche, les prédictions du programme élastodynamique par la méthode des différences finies WAVE sont appropriées à la modélisation d’un nombre limité d’évènements de façon à déterminer soit les vitesses à petite échelle et les dommages, soit les effets des fractures et excavations sur la réponse de basse fréquence à grande échelle. Seismische Integrationsschemata zielen darauf ab, Reaktionen der Gesteinsmasse, die von den Berichten seismischer Aktivitäten stammt, zu inkorporieren um numerische Modelle in die Lage zu versetzen, künftige Antwort zum Bergbau zu reproduzieren. Bis dato betrachteten Integrationsschemata die Fälle mit quasi-statischen Modellen. Diese Arbeit stellt Fallstudien dar, die einige der seismischen und modellierenden Fragen betrachten, die benötigt werden, um diese Schemata auszuweiten, um die dynamischen Charakeristika seismischer Fälle einzuschließen. Das Endziel eines automatisierten Integrationschemas erscheint für das dynamisches Berechnen undurchführbar. Die Vorhersagen des WAVE elastodynamisch begrenzten Unterschiedprogramms sind jedoch verwendbar für das Berechnen von begrenzten Anzahlen von Fällen, um entweder die Nahfeldgeschwindigkeiten und Schaden oder den Effekt von Brüchen und Extraktionen auf der Fernfeld Niederfrequenzantwort festzustellen.

Jan 1, 2003