Search Documents

By A. J. Burger, F. L. D. Cloete

Tests indicated that effective recovery of pyrite from a coarse Witwatersrand quartzitic ore can be accomplished by intensified flotation in an air-sparged hydrocyclone. Air is fed through the porous cylindrical wall of the hydrocyclone into a swirling layer of slury. Hydrophobic particles are attached selectively to small air bubbles, which form a froth and are recovered through the overflow. Hydrophilic particles pass out in the underflow. A spigot in which flow is restricted by an orifice was found to be more successful in preventing blockage by wood chips than an annular opening between a pedestal and the cylinder wall. Pyrite recoveries of 85 to 93 per cent at grades of 35 to 40 per cent sulphur were obtained in the air-sparged hydroclone with residence times of about 1 second. Comparative tests in a batch flotation cell after 320 seconds yielded average recoveries of up to 96 per cent, but with a mean grade of 32,5 per cent sulphur. A high colector dosage of 120 g/t was required in the cyclone, compared with the 40 gft used in conventional operations. An air flowrate of about 150 I/min was adequate at a slury feed rate of 35l/min. Particle sizes between 38 and 106µm yielded the best flotation results.

Jan 1, 1988

It is suggested that an increase in the production from thin coal seams in South Africa is necessary, and that a substantial amount of any increase will be mined by the bord-and-pillar method. For the purpose of this study, a thin coal seam was regarded as any seam 1,5 m thick or less to the minimum thickness at which mechanized equipment can operate in bord-and-pillar workings. The equipment being utilized in thin-seam bord-and-pillar layouts includes conventional equipment, load-hauldump cars (scoops), and drum-type and Fairchild-Wilcox continuous miners. Comparisons are made of these types of equipment for bord-and-pillar mining at various seam thicknesses within the thin-seam range. The evaluations involved production rates and the cost of extraction for South African conditions, use being made of an existing computer modelling technique in the generation of production rates. The indications are that, for seam thicknesses greater than 0,9 m, drum-type continuous miners utilizing continuous haulage are the most productive and cost-effective equipment at present operating in thin-seam bord-and- pillar workings. Where seams thinner than 0,9 m are to be exploited, Fairchild-Wilcox continuous miners, particularly the Mark 22, produce the most coal at the lowest cost.

Jan 1, 1984

By R. du Preez

Tati Nickel is currently operating a hydrometallurgical demonstration plant in Botswana, using the Activox® process developed by LionOre Technology to produce nickel cathode and a cobalt salt from a sulphide concentrate. Cobalt is extracted using Cyanex 272. This reagent also extracts all the iron, aluminium, copper, zinc, and manganese from the nickel stream. Versatic 10 carboxylic acid is then used as extractant to recover nickel from the stream, separating it from calcium and magnesium, and upgrading it to provide a suitable advance electrolyte for nickel electrowinning. However, the selectivity of Versatic 10 for nickel over calcium is limited, and gypsum formation in the extraction circuit is a problem when attempts are made to maximize the recovery of nickel. Mintek has developed a synergistic system with Versatic 10 for improved separation of nickel from calcium and magnesium. Laboratory testwork was conducted on the raffinate of the cobalt solvent extraction circuit to optimize the Versatic 10/Nicksyn? (Mintek synergist) system to be employed. Extraction and stripping parameters suitable for this stream were optimized in the laboratory and then applied on the demonstration plant. A commercial batch (0.5 tons) of Nicksyn? reagent was produced for the demonstration plant. The laboratory testwork results and the demonstration plant performance are discussed in detail in this paper.

Jan 1, 2007

By D. E. Sweeney

In May of 1980, a mine operated by Belmoral Mines Ltd experienced a failed crown pillar, resulting in the death of eight miners and putting sixteen others in harm?s way. The Ferderber mine was located in the Val d?Or region of the province of Quebec in Canada, and had been under development for 19 months and production for 9 months, since the opening of the portal. The crown pillar separating the 1?7 level from overlying overburden ultimately failed, permitting an estimated 1.5 million cubic feet of liquefied sediment to gain entry into the mine. This paper back-analyses the cave-in by applying decision error theory, in an examination of the organizational culture and the collective decisions contributing to the cave-in disaster. A case will be made for a greater understanding of mining methodology, geomechanics and risk assessment when operating in such challenging geologic conditions. Boundary condition and decision (BCD) analysis will be introduced as an innovative new method for the analysis of mine accidents and incidents. It will also be shown that BCD analysis can be applied to any event in an enterprise for which standards, norms or legislation exists. A cognitive profile will be presented that provides insight into the safety ethos existing within the Ferderber mine organization at the time of the tragedy.

Jan 1, 2007

By C. G. Carey, M. P. Mullins

BHPBilliton is a large (US$32bn market capitalization) diversified mining group. Significant organic growth is planned through the development of a number of mining, processing and oil and gas projects, totalling some US$5.2bn over the next three years. The investment standards underpin the capital approval process, and incorporate the requirements for range and risk analysis of key input variables, including mineral resources. Public reporting codes for mineral resources and ore reserves (such as JORC) stipulate deterministic reporting of estimates, but are generally silent on any requirement for range or risk assessment, although they acknowledge the risk and uncertainty in the production of resource estimates. In contrast, public reporting of petroleum reserves allow for the use of either deterministic or probabilistic estimation, and for the latter, mandate the level of confidence required for proven versus probable reserves. Conditional simulation techniques, popular in the petroleum industry, provide an ideal tool forrange and risk assessment of the range of outcomes of key resource parameters, such as tonnagesand grades. Examples of a diamond deposit and of a porphyry copper deposit are presented. The understanding and quantification of mineral resource risk through a technique such as conditional simulation provides quantified information on the potential upside or downside. These techniques should be more widely utilized in the high-risk minerals extraction industry. Keywords: mineral resources, conditional simulation, risk, capital investment standards, BHPBilliton.

Jan 1, 2003

By L. Raaths

This paper outlines the process of improvement utilizing performance monitors and GPS systems on an opencast strip mine. Its primary focus is to maximize coal exposure by draglines and secondly to improve on those processes impacting directly on the dragline operation. The Aquila (DM2/5 system) navigation and monitoring systems were installed on the overburden drills. Their main function is to eliminate manual staking and positioning thereby ensuring a regular pattern being drilled. Holes drilled to planned depth reduce drill metres and it minimizes coal losses and contamination at the coal interfaces. The CAES (Computer Aided Electronic System) will be installed and evaluated on the Caterpillar D11 dozers at Optimum. This system ensures a correct dragline pad elevation through the use of planned elevations and GPS technology to achieve the optimal pad elevations for draglines consistently. The draglines are equipped with a Dragline & Operators Performance Monitor. This monitor allows the operator to control his own performance. It reports on all productivity, method and poor operating techniques. These monitoring systems send critical operational information back to the office. This source data resides in central databases from where it is converted and integrated into management information. To manage an operation means that you as a manager must be able to set objectives and targets and to achieve your goals the activities involved must be measurable.

Sep 1, 2001

By L. R. Nelson

The efficiency and cost-effectiveness of the aluminothermic reduction process in the production of ferro-alloys and 'pure' metals depends strongly on appropriate balancing of the process energy required. Insufficient energy results in a poor metal yield, while over-supply can result in excessive fuming and possibly even ejection of the reactor contents in a potentially dangerous 'thermite bomb' reaction. This situation becomes even more critical when the suitability of limited quantities of oxide from new sources must be evaluated, dictating smaller-scale testwork. The resulting higher relative heat losses from the system complicates control of the energy balance, and usually requires the addition of thermal boosters or reactant preheating in order to sustain an autothermic process. This often detracts from the quality of the metal product, and adds to the hazards of batch aluminothermic- reduction testing. The development of a small-scale method (producing less than 2,5 kg of metal) for the plasma-assisted aluminothermic reduction of chromium oxide that overcomes such difficulties is described. The technique involves the use of a sealed 50 kVA plasma-arc furnace to provide controlled electrical ignition and supplementary energy to the reactants contained in a water-cooled copper crucible. The application of the method to the evaluation of the aluminothermic production of pure chromium metal from a unique chromic oxide source is reported.

Jan 1, 1996

By K. Hodgson, J. P. M. Hojem, N. G. W. Cook

Already about one-third of South Africa's coal is mined at depths exceeding 100 metres. Almost all this mining is done by the bord and pillar method. Conventional design procedures call for ever larger pillars as depths of workings increase, resulting in the loss of large amounts of coal and reductions in productivity. Barrier pillars are in general use to ensure against large collapses. The presence of these strong pillars would allow a more efficient design of the bord and pillar layout to yield improved extraction ratios by using smaller, yielding, pillars between the bords. Knowledge of the complete load- displacement curves for such pillars is a prerequisite for the design of such a system. A 100-MN, stiff jacking system for measuring the complete load-displacement curves of pillars with cross-sections of up to 2 m X 2 m is described. The jacks are installed in a slot cut across the central plane of symmetry of a pillar, thereby ensuring that the stress distribution in the pillar during a test, especially at its contacts with the roof and floor, is identical to that caused in a similar pillar by convergence across the seam. Preliminary results in the form of complete load-displacement curves for test pillars of about 1.5 metre square section are given.

By M. S. Janssen, J. L. Taylor, M. A. Ford, E. B. Viljoen, H. A. Simonsen

The Stilfontein and Buffelsfontein Gold Mines, near Klerksdorp in the Transvaal, had accumulated a large amount of uranium-containing residue and, when the price of uranium rose in the 1970s, consideration was given to the possible recovery of this uranium. Preliminary tests showed that concentration of the uranium prior to leaching would not be economic. However, the pyrite in the residue could be concentrated by flotation, and the flotation concentrate could be roasted to pro¬vide both enough acid for leaching the uranium and a calcine from which the gold could be recovered. The feasibility study showed that a uranium operation of 270 kt per month would be most economically attrac¬tive, and a plant of that size was accordingly designed and built. In the first six years of its existence, the plant treated over 20 Mt of residue and produced about 3,5 kt of uranium oxide. During that time, the plant was con¬tinually being improved to make it more reliable and cost-efficient. This paper analyses the operation of the plant during its first six years from the viewpoints of its mechanical, process, and economic performance. The criteria on which the selection of the process was based are reviewed and compared with the actual performance of the plant, emphasis being placed on the leaching, solid-liquid separation, recovery, and purification stages.

Jan 1, 1987

By J. L. Gaigher

A simple mineralogical regression model is described, which was devised in order to help the flotation plant cope with rapidly changing headgrades and feed mineralogy. Minerals in the feed were determined by means of quantitative X-ray diffraction and compared with plant performance parameters and flotation reagent consumption rates, using regression analysis. A mineralogical regression model for predicting recovery served to motivate flotation plant personnel and also set standards whereby flotation performance could be measured. The reagent consumption model indicated in which direction any or all of five flotation consumption rates should be altered. All practically measurable parameters, even those showing poor or no correlation, were included in the model, provision being made for the continuous update of a batch of data of 30 lines. Compared with the method of multiple linear regressions, the r2 is poorer at 0,41 (versus 0,50), but the mean standard error of estimate for both methods is identical at ± 6,6 units. The regression model is simpler than the method of multiple linear regressions, and although the accuracy of prediction is not high (41%), the mineralogical regression model proved to be successful in practice. Flotation efficiency, as measured by the mean ratio of head to tails grade, for the 9 month period after the mineralogical regression model was implemented on an hourly basis, improved from 2,8 to 3,2, which is equivalent to an improvement in average flotation recovery of 5% relative.

Jan 1, 1987

By H. Cevizci

In this study, a newly developed plaster stemming method is studied and compared with the usual dry drill cuttings stemming method for surface blasting in mines and quarries. Drill cuttings are generally used in open pits and quarries as the most common stemming material since these are most readily available at blast sites. However, dry drill cuttings eject very easily from blastholes without offering much resistance to blast energy. The plaster stemming method has been found to be better than the drill cuttings stemming method due to increased confinement inside the hole and better utilization of blast explosive energy in the rock. The main advantage of the new stemming method is the reduction in the cost of blasting. In one series of blast tests, blasting costs per unit volume of rock were reduced to 16 per cent by increasing burden and spacing distances. Also, better fragmentation was obtained by using the plaster stemming method. Blast trials showed that plaster stemming produced finer material. In the same blast tests, +30 cm size fragments reduced to 5.4 per cent of the total, compared to 37.7 per cent in the conventional method of drill cuttings stemming. With this method of stemming, vibration and air shock values increased slightly due to more blast energy being available for rock breakage, but these increased values were small and under the permitted limit for blast damage criteria.

Jan 1, 2012

By R L. Bowers, D S. Smit

In light of soaring commodity prices, Nkomati has investigated the potential of processing additional low grade nickel ores to add to their reserves. The Chromititic Peridotite Mineralised Zone (PCMZ) was identified as one ore type with the potential of producing a high grade nickel concentrate. In addition to the nickel, copper, cobalt and PGM?s, the ore also contains a significant amount of chromite which adds substantial value to the project. Pyrrhotite, pentlandite, chalcopyrite and chromite are the dominant minerals within the ore, which on average grades around 0.23% Ni and 12% Cr2O3. The PCMZ ore contains excessive amounts of fibrous silicates which makes it a challenging float, with gangue control as the key element to success. Extensive laboratory testwork, which eventually led to a pilot plant campaign, was undertaken with the aim of developing a process route for treating the PCMZ ore. Several flotation circuit configurations were tested and results from the optimal circuit indicated that a nickel concentrate grading at 8.5% is achievable at a recovery of 78%, with substantial recoveries for the copper, cobalt and PGM co-products. The chromite concentrate, grading at 45%, was extracted from the flotation rougher tailings via a spiral plant. These promising results were incorporated into the plant design and are currently being evaluated in a bankable feasibility study, which will see the current 100ktpm MMZ concentrator being upgraded to a 250ktpm PCMZ concentrator as part of Nkomati?s Phase II expansion.

Jan 1, 2007

By Z. Nzimande

The Constitution of the Republic of South Africa advocates the importance of sustainable economic development and justifiable environmental consciousness by business. The government needs to ensure that every citizen of the Republic has access to an environment that is protected, pollution free, and sustainable by enacting certain regulations. However, there are more than 5 700 derelict and unrehabilitated mines of all types in South Africa. Former asbestos operations were among the first to be targeted for clean-up under the programme instituted by the Department of Mineral Resources (DMR), owing to the proven direct impact of asbestos pollution on health. This paper seeks to investigate the challenges faced by the coal sector as far as mine rehabilitation and closure is concerned. For the purpose of this paper rehabilitation is defined as per the Chamber of Mines Rehabilitation Guidelines publication, which defines rehabilitation as putting the land impacted by mining activities back to a sustainable and usable condition. Some of the current rehabilitation challenges are technical skills (know-how), leadership focus, poor planning, cost saving initiatives, and the government's lack of capacity to enforcement rehabilitation requirements. It is imperative that mining companies identify rehabilitation as a critical strategic pillar that directly influences license to operate. The case study evidence indicates that relevant policies, appointment of accountable people, sufficient leadership support, and the correct choice of rehabilitation equipment can assist to improve the rehabilitation and land management challenge.

Jan 1, 2012

By M. F. G. Bruce

Two backfill systems have been developed on West Driefontein, namely the centrifuge dewatered tailings system and the cyclone-classified tailings system. Modifications to the two systems since the publication of the original paper (Close and Klokow, 1985) are discussed in addition to the results obtained. Considerable experience has been gained from the operation of the centrifuge dewatering units as well as the placement of dewatered tailings in a difficult mine environment. The centrifuge dewatered tailings method has proved successful in the extraction of a highly stressed block of ground at No. 5A Sub-vertical Shaft. The utilization of backfill support in this area made it possible to dispose of a high-grade barrier pillar. This pillar was considered necessary prior to the introduction of backfill support. The recovery of the gold from this pillar made the use of dewatered tailings backfill cost- effective, despite high labour and maintenance costs. Current experience with the bagfilling method of placing cyclone- classified tailings indicates that it is viable and requires considerably less capital investment. Although expensive at present, it is envisaged that costs will decrease once cheaper bags and other forms of stope support are used. The placement of backfill in small-diameter sausage-type bags requires no change in mining cycle and allows the backfill to be placed close to the stope face. Both backfill systems are being expanded but preference is to be given to the cyclone-classified tailings system.

Jan 1, 1988

The Canadian Institute of Mining and Metallurgy. Milling practice in Canada. CIM Special Volume 16. 1978. The purpose of this volume is to up-date The Milling of Canadian Ores, which describes Canadian mineral. processing plants and gives other metallurgical information, and was published by the Sixth Commonwealth Mining and Metallurgical Congress in 1957. NIM reports Report no. 1874 Activation analysis and classification to soune of samples from the Kimberley Reef conglomerates. (10th Mar., 1977; released Jun. 1978). Report no. 1926 The analysis of anode sludges by X-ray-fluorescence spectrometry. (5th Jun., 1978). Report no. 1936 The analysis of mineralogical and metallurgical materials. A guide to the analytical techniques and instrumentation available at the National Institute for Metallurgy. Report no. 1959 The slag-metal equilibrium, and the activities of slag and metal components in the production of high-carbon ferromanganese. (15th May, 1978). Report no. 1965 Analyses, by several laboratories, of three ferromanganese slags. (22nd May, 1978). Report no. 1968 The influence of carbonaceous reducing agents on the rate of reduction of representative manganese and chromium ores. (28th May, 1978). Company Affiliates Guide To The Preparation Of Papers for Publication In The Journal Of The South African Institute Of Mining And Metallurgy The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal.

Jan 1, 1979

By A. J. Van Rensburg, N. B. Strydom, C. H. Van Graan

The design, construction, and use of a practical ice-jacket for miners by N. B. STRYDOM, Ph.D. (Illinois) (Fellow), D. MITCHELL, Ph.D. (Rand) (Member), A. J. VAN RENSBURG, M.Sc (Poteh) (Visitor), and C. H. VAN GRAAN, M.Sc (Pretoria) (Visitor) Microclimate suits have been shown to be very effective in decreasing physiological strain in hot, wet environments, thus enabling men to work without risk in areas that would normally carry a high risk of heat stroke. In this paper, some design considerations in the development of the frozen jacket are described. Water complied with most of the desirable properties required of a coolant material for use In a microclimate suit. The Human Sciences Laboratory has developed a jacket in which ice is used as the coolant and which is designed according to the most acceptable anthropometrical characteristics. The jacket consists of an inner poncho-type waistcoat containing 28 water compartments. Over this is worn an insulating jacket, which minimizes warming of the coolant by the environment. Suitable refrigeration units have been developed to freeze the jackets underground. Laboratory tests have shown that these jackets are effective for about 2,5 hours, Irrespective of the wet-bulb environment, when men are working at a moderate rate. Jackets should, however, be used only in environments in which the wet-bulb temperature is in the range of 32,S0 to 35,S °C.

Jan 9, 1974

An International Ferro-alloys Congress, arranged by the Ferro Alloy Producers' Association of South Africa, the South African Institute of Mining and Metallurgy, and the National Institute for Metallurgy, will be held in Johannesburg, South Africa, in April 1974. The technical programme, occupying five days, will cover the following topics in relation to all ferro-alloys: 1. Burden preparation, blending, pelletization, handling, reducing agents. 2. Electric smelting furnaces-design, operation, management,- smelting optimization, shop practice, refractories. 3. Mineralogy, reduction behaviour, smelting reactions, slags. 4. Automation, Pollution control. 5. Applications, trends in comsumption, trends in composition specifications. There will be no parallel sessions. Papers in the above topics are invited; review papers will also be welcome. Proposed titles and abstracts in not more than 200 words should be submitted before the 30th of November, 1972, to The Chairman, Programme Committee, INFACON 74, Private Bag 7, AUCKLAND PARK, South Africa. The abstracts will be considered during January 1973, and papers accepted for the Congress must be submitted in final form before the 31st of July, 1973. The proceedings of the Congress will be published as a special volume. There will be a series of post-Congress tours to ferroalloy plants and other places of both technical and scenic interest. A full ladies' programme will be arranged. The First Circular, giving further details, can be obtained from: The Secretary of the Organizing Committee, INFACON 74, Private Bag 7, AUCKLAND PARK, South Africa.

By E. -U. Reuther

To improve the climatic environment underground the German coal mining industry has installed refrigerators with a capacity of 300 MW cooling power. One third of this total is accounted for by central refrigeration plants with more than 5 MW capacity. The central refrigeration comprises three stages: mechanical cooling, transport and distribution of chilled water via pipelines and exchange of heat in the air coolers. Of these three stages only the mechanical generation of chilled water has been resolved satisfactorily. Transport (including distribution) and exchange require further technical research. The Mining Institute of the Aachen University of Technology has done extensive studies on this subject, concentrating on controlling the flow of chilled water according to demand in the mine. Additionally, the favourable exchange in the air coolers is taken into account. The studies are based on a model mine which simulates the conditions in deep coal mines in Germany. The simulation program represents firstly the condition of the mine air at the location of the air being cooled, then the heat exchange in the air cooler itself, and finally the transport of the chilled water from the central refrigerator to the consumer. The program also reproduces the seasonal and operational changes in conditions of mine air as well as different air cooler designs. A regulated distribution of chilled water is also suggested. Finally, estimations of costs can be made as an aid for further planning.

Jan 1, 1987

COUNCIL The following served on Council during the year under review: Office bearers: Messrs V. C. Robinson (President), Prof D. D. Howat and Dr J. P. Hugo (Vice-Presidents), J. K. E. Douglas (Immediate Past President) and D. G. Maxwell (Honorary Treasurer). Ordinary Members of Council: Dr M. G. Atmore, Dr J. M. Bereza, H. P. Carlisle, W. W. Malan, C. E. Mavrocordatos, Prof R. P. Plewman, Dr R. E. Robinson, Dr M. D. G. Salamon, P. W. J. van Rensburg, L. W. P. van den Bosch, P. A. von Wielligh. Branch Chairmen: J. Meintjes, J. M. Meyer (Acting), J. N. Saunders (Retired). Past Presidents serving on Council: R. J. Adamson, M. Barcza, H. Britten, R. C. J. Goode, P. Lambooy, Prof J. de V. Lambrechts, Dr J. T. Mclntyre, J. F. Reid, H. Simon. Ten Council meetings were held during the year with an average attendance of eighteen and the standing committees held forty-six meetings. FINANCE The annual accounts, which are attached to this report, show an excess of income over expenditure of R5 051 compared with an excess of expenditure over income last year of R4 608. This major reversal of fortunes is due in the first instance, of course, to the increased subscriptions. There were, however, other important contributors, particularly sales of the Proceedings of the Symposium on Open Pit Mining and profits on the operation of symposia and colloquia. It would appear from a study of the accounts that there has been a substantial drop in expenditure on secretarial fees. In actual fact, however, our total expenditure on secretarial fees was higher. A portion of this expenditure was charged against the administration of the Symposium on Open Pit Mining and, in addition, the charge against the Journal accounts for secretarial fees was increased. It will be recalled that in last year's annual report it was mentioned that subsequent to the new arrangement for publication of the Journal, the expected improvement in the finances of the Journal had been slow in materialising. After a total period of 18 months there was still no sign of improvement and it was accordingly decided to end the arrangement. As a result, the drain on the finances of the Institute was considerably lessened in the second half of the year. During the course of the year Council became concerned about the rapid depletion of our accumulated funds and gave careful and detailed attention to all aspects of the Institute's financial affairs. Particular attention was given to: 1. The fact that the Institute does not have a solid financial backing and must appeal for funds every time any special event such as a symposium is held. 2. The responsibilities of the Institute to the profession and the community, with particular reference to the desirability of establishing Institute bursaries and participating in other educational activities. 3. The rapidly rising cost of living. 4. The immediate financial position of the Institute. 5. The rapidly increasing cost of publishing the Journal due to the increasing number of papers available. In the meantime the immediate financial position of the Institute has improved but as this is due largely to non-recurring or irregular items of revenue, it should not be given undue weight. After careful consideration it was decided that an appeal should be made to industry for financial assistance, which would be used to cover the cost of symposia and other unusual expenditure and also, if possible, to build up the capital resources of the Institute so that there is a solid foundation for the future. Before appealing to industry, Council wished to be quite certain that there could be no criticism of the Institute for not having done our best in a personal capacity. Furthermore, Council examined many comparative statistics, including those circulated to members, which showed that, while expenditure per member has risen at an average annual rate of 7,5% over the last fifteen years, subscription revenue per member has risen at only 3,4% per annum. It was with this background that your Council decided to raise the subscriptions. Initial approaches have been made to the big mining groups and there has been a very generous response, although the details of how financial assistance will be provided have not yet been worked out. It seems likely that some form of affiliated company membership will be the most suitable method of achieving this. When these details have been fixed, it is the intention to extend the appeal to all corners of the mining industry as well as manufacturing and metallurgical industries. It is believed that these measures will ensure that the finances of the Institute are placed on a firm foundation on which the expanding activities can be planned. The MacArthur Forrest Memorial Fund shows an excess of income over expenditure of R73 and the total fund was, therefore, increased by this amount to R4 411. The balance sheet shows that the market value of quoted shares and debentures increased during the year fron R6 540 to R9 160. The market value is now almost exactly the same as the book value. Accumulated funds now amount to R23 010 compared with R17 959 a year ago.

By M. I. Mabala, B. P. Watson, M. J. Kanda

A failed and stable Upper Group 2 chromitite pillar database was collected in 2007 as part of the PlatMine 1.2 pillar strength project. The database consisted of 177 pillars, of which 33 had failed. Most of the data were collected from various intermediate-depth mines near the town of Thabazimbi. Spans between rows of chain pillars were about 30 m. Pillar loads were estimated using pseudo-3D, elastic, boundary element modelling software. The pillar-load data were evaluated using a maximum likelihood regression analysis to determine strength parameters, following a similar approach to historically acceptable practice. The original formula was named the PlatMine Formula. This paper describes re-evaluations of the database, using a linear formula and several variations of the power formula. The formula providing the lowest standard deviation to the data in the database was considered the best representation of the pillars in the database. Through this rigorous process, a new formula for peak pillar strength was developed for Upper Group 2 chromitite pillars, which is unaffected by volume. The small standard deviation provided by this formula suggests a reliable relationship between strength and w/h ratio, in the w/h ratio range between 1.5 and 4.7. Accuracy, precision, and recall analysis confirmed the efficacy of this equation to the data in the database. Importantly, the new formula provided in the paper does not predict a significantly different strength to the current PlatMine formula, within the confines of the database.

Nov 27, 2024