Search Documents

By C. Birch, M. Katuruza

"The purpose of this study was to demonstrate unmanned aircraft system (UAS) technology in opencast highwall mapping using the experience at Isibonelo Colliery in Mpumalanga Province of South Africa. In opencast mines, geological mapping has evolved over time and there have been challenges in extracting valuable information from exposed highwalls due to restricted access for safety reasons. A UAS was used at Isibonelo Colliery to conduct highwall mapping, using drone-based digital photogrammetry techniques. A demonstration survey was undertaken during February 2018. The highwall flyover demonstration was planned for two areas (North and South pits) where field control points were placed by the mine survey department. A contractor used a DJI Phantom 4 (Pro) for the highwall mapping. Raw data was processed within 48 hours and a 3D model of the mapped pit area was produced. Further data extraction included obtaining updated weathering and lithological contact elevations and thicknesses for use in short-term planning. The results showed a good correlation between the resource model and the UAS data model. The project was considered a success and highwall flyover mapping and is now standard practice at Isibonelo Colliery.IntroductionDetailed geological mapping is crucial to the understanding of the structure of any mineral deposit. Several mapping methods may be applied depending on the available exposure/outcrop and nature of the orebody; for example, coal deposits typically suboutcrop only, therefore an opencut highwall provides the best exposure for mapping the geology. Mapped information, when incorporated into a resource model (generated from exploration borehole data), improves the understanding of the orebody or coal seam. This research paper focused on the use of unmanned aircraft system (UAS) technology for pit highwall mapping to generate data for updating geological models and avail the latest information to mine planning to improve the short-term plans."

Mar 1, 2019

By S. Annavarapu

"Fragment size distributions play an important part in the design and planning of block cave mining operations. Though several methods have been proposed for estimating fragment size distributions in advance of mining, the calibration of these estimating procedures to field measurements has been a challenge. The Block Size Estimator (BSE) program was developed for providing an assessment of primary fragmentation expected in a block cave mine using drill-core piece length data and joint characteristics from the exploration and geotechnical evaluation programmes. In order to validate the results from the BSE program, the drill-core piece length data and the joint characteristics in different rock types from the DOZ block cave mine in Indonesia were used to help generate fragment size distributions in different areas of the mine. The predicted fragment size distributions were compared with the fragmentation observed at the drawpoints during operation of the mine.This paper presents the details of the validation of the fragment size estimates by the BSE program using fragment size distribution data from the drawpoints at the extraction level at the DOZ block cave mine, and the challenges encountered in developing reasonable correlations between the estimated and measured fragment size distributions. IntroductionThe assessment of fragmentation is an important aspect of the design and planning of the block cave mining method, and forms an integral part of the design of the excavations at the extraction level and the selection of material handling systems for transporting the ore to the processing stations. Secondary blasting requirements can also be estimated based on the fragment size distributions developed for the block cave (Laubscher, 1994).Several methods of estimating fragment size distributions in block cave mines have been developed based on joint set parameters estimated from structural data from oriented core drilling campaigns and mapping of available excavations and outcrops. The BCF program (Esterhuizen, 1999) estimates the fragmentation using a combination of empirical, analytical, and rational methods to model the behaviour of materials during the primary and secondary fragmentation processes. The program JKFrag uses advanced tessellation of joint traces to create rock blocks and then generate fragment size distributions (Brown, 2002). Nickson, Coulson and Hussey (2000) presented the details of processing of the geotechnical data from the Mont Porphyre project, including an assessment of block sizes from the data collected on the core logging sheet. The distance between natural fractures was used to create distributions of block lengths, and a distribution of potential block sizes was estimated assuming that the blocks had equal dimensions in all directions. The results agreed closely with the results of the BCF program. Hadjigeorgiou, Grennon, and Nickson (2002) demonstrated the use of oriented borehole data to provide characteristic block size distributions for a mining project using a software package called Stereoblock, which generates a three-dimensional joint network for a given volume and calculates the volumes of blocks created by the intersections of these joints, simulated as circular planes. The distributions of joint orientation and joint spacing generated from statistical analysis of the oriented core data are used for the creation of the Stereoblock model. The diameter of the circular planes representing the joints is determined based on the mean and standard deviation of the joint trace length obtained from scan-line mapping."

May 1, 2019

By G. P. O’Malley, A. N. Nikoloski

One of the most promising options for extraction of copper from low-grade chalcopyrite ores by heap leaching, however, chalcopyrite is refractory and suffers slow leaching kinetics and poor overall extraction due to formation of a passivation layer on the particles. The solution composition is believed to strongly affect the formation of this layer. This paper examines the effects of the major cationic species of Fe3+/2+, Mg2+, Cu2+, and Al3+ and the anionic SO42− species in acidic ferric sulfate media with a composition simulating recycle heap leach conditions. It was found that altering the sulfate, iron or aluminium concentration had significant effect on the copper extraction, the concentration of copper slightly influenced the extraction, and the amount of magnesium had no appreciable effect. Also, iron and aluminium caused a change in the sulfate concentration, and the sulfate ions had the greatest influence on the extraction of copper under recycle leach conditions

Jan 1, 2023

By E. Molobi

"Studs are rods threaded on both ends and are used as mechanical fasteners for two or more components. Stud finds usage in industries such as automotive, construction and aviation. The advantage of studs is that they allow for disassembly of components during maintenance. Studs are continuously subjected to both tensile and shear stresses, depending on the application, therefore they should be manufactured from suitable materials that are capable of withstanding all these external forces. Studs are sometimes manufactured from re-sulphurized steel due to its improved machinability; however, there is a certain limit on the amount of sulphur, above which failure may occur. Premature failure of studs has been a common problem, but failed studs are commonly replaced with new ones without conducting failure investigations. The present work investigates the premature failure of two re-sulphurized steel studs used on a rocker arm assembly and recommends alternative materials. The investigation was carried out by conducting visual examination, microstructural analysis, hardness measurements, chemical analysis and a detailed scanning electron microscopy (SEM) investigation on the fracture surface.IntroductionTwo rocker arm studs used on a 16-cylinder diesel locomotive engine failed prematurely after being in service for less than 5 months. The rocker arm studs had a life-cycle of 5 years. The studs were manufactured from resulphurized steel. The paper aims to establish whether re-sulphurized steel is applicable for the manufacture of studs in the automotive industry.BackgroundLocomotives are classified as either electric or fuel-powered. Diesel locomotives are an example of fuel-powered locomotives. This type of locomotive uses a diesel engine as a means for propulsion. An engine converts chemical energy into mechanical energy required for traction. In an internal combustion engine a rocker arm is an oscillating lever that conveys radial movement from the cam lobe into linear movement to open and close poppet valves of cylinders (Husain and Sheikh, 2013). The rocker arms are secured on to the cylinder head by rocker arm studs."

Jan 1, 2016

By B. P. Watson

The discussion written by Dr de Frey suggests that mine design should be based on closely spaced stability pillars. However, this concept leads to low extraction ratios at depth. The concept of `crush' pillars in conjunction with more widely, appropriately spaced stability pillars allows for significantly larger extraction ratios, particularly at depth. It should be noted that the rock conditions in many areas of South African platinum and gold mines are good, allowing significant spans to be mined safely between stability pillars. `Crush' pillars are cut small enough to fail stably near the face under stiff loading conditions, and their residual strength is intended to support about 10 m rock height between stability pillars. While this support resistance cannot be achieved by conventional support, crush pillars have been proven to have the required capacity for this purpose. The concept of leaving smaller crush pillars with appropriately positioned stability pillars has been used successfully for more than 30 years in areas of South African platinum and gold mines.

Jan 1, 2011

By M. H. Lampen

The SILAG Material Tracking System MTS monitors and controls the complete material flow throughout the plant - and even companywide. The customized system developed by Siemens especially for bulk material handling applications enables companies to track bulk material from the mine to the harbor, to the steel mill or to the power plant. All relevant material data is available at every single step of the material’s journey. SILAG is an open, scalable system based on Windows NT / 2000. Using standard interfaces of Windows NT, like API, ODBC, SQL and socket technology, the system is very flexible and can easily be tailored to meet different requirements. SILAG can be used as a stand-alone solution or - if complete plant control and visualization is required - as a component of a fully integrated automation system with the Win CC HMI system and the PCS7 process control. In contrast to conventional material tracking systems, SILAG offers many advantages. - The Material Tracking System is an object oriented, online to the process, linked system. All changes in the plant during operation e.g. selecting another conveyor route, start and stop etc. will be automatically detected and will influence the calculation. - The systems is able to split and blend material (quantity and quality).Measurements of tonnage, volume or quality analysis can be linked online to the system. Each movement of material is monitored by the system and leads to online recalculations of the images and databases. - All material data is based on 3D-stockpile images, which are calculated by an internal mathematical model based on quantity and quality information. - If a laser scanner is available on a stockyard machine it can be taken to update the profile directly from the piles. - Efficient control and report functions are available on each, free selectable point of the total plant.

Sep 1, 2001

By C. J. Badenhorst

Occupational illnesses and diseases tend to be chronic and are generally characterized by temporary or permanent physical dysfunction. With the exception of some symptoms, they are not generally visible. Therefore, safety overrides health in mining because occupational ailments take years to develop and management observes less physical trauma, if they witness anything at all. Occupational health issues need to be addressed systematically, encompassing all aspects of the interaction of employees within the work environment. Risk assessment is central to the management of occupational health. This should not be seen as a complex process and may involve little more than simply considering the consequences of one?s actions before starting work. Competent risk assessment provides the starting point and defines the scope of further action. The objectives and final use of an occupational health risk assessment determine the process and the method by which it is carried out. The occupational health risk assessment is therefore a systematic procedure to identify potential health hazards, evaluate the extent of exposure subjectively and/or objectively, and to establish the need for, and effectiveness of existing control measures. Furthermore, it facilitates the drafting of occupational exposure monitoring, medical surveillance and occupational health education programmes. Various models for conducting occupational health risk assessment provide step-by-step guidance for the identification and assessment of significant occupational health hazards and assist in producing suitable and significant occupational health risk assessments. The paper gives an overview of an occupational health risk assessment model based on the basic principles of occupational health and the legislative requirements, which will simplify the occupational health risk assessment process and ensure a sound base for the development of all other occupational health systems.

Jan 1, 2004

By M. Keevy, K. Hackney

Centrifugal slurry pump station and deposition sites are a common feature of many mines and mineral processing plants. Yanacocha Mine has completed the design of a pump station consisting of two trains of four pumps each. A number of trade-off studies was conducted to optimize the pump station design. The most significant of these was determining the drive types for the slurry pumps. The pump station duty can vary considerably due to the number of deposition points round the disposal site. The standard solution to this problem on a multi-stage pump train is to install one pump with a variable speed drive to control the pump station output by varying the speed of this pump and stopping and starting other stages. However, there are a number of negative impacts associated with this approach. These include head losses through pumps that are stationary or ?wind-milling?, different wear life on pumps that are running and pumps that are stationary, and slower response to the control system with the possibility of hunting. The use of variable speed drives on all the pumps was considered as an alternative to the standard solution. The factors considered in comparing these options were the control and operational differences, the pump efficiencies and absorbed power, the expected pump wear life, the impact on pump maintenance and the cost of the drive options. For this project the option of using all variable speed drives was selected. The paper presents the following aspects of the study: ?Description of the various options investigated. This includes a discussion on the required duty and the drive options. ?Technical comparison between the options. ?Description of the factors influencing pump performance and life.

Jan 1, 2007

By More-O&apos, R. C. Ferrall, J. W. Wilson

SYNOPSIS The theory of elasticity has been shown to provide a means of determining the stresses and displacements induced by mining in deep level hard rock mines. This theory has been incorporated into an electrical resistance analogue on which the plane of a reef or ore-body can be modelled to enable the rapid determination of stresses and displacements at points in the plane of the reef. This electrical analogue has been used to determine energy release rates caused by scattered mining, which, to some extent, is a measure of the degree of hangingwall fracture. A correlation between predicted energy release rates and actual underground conditions in stopes in the O.F.S. goldfields has been encouraging enough to define parameters on which future stoping layouts can be based. The use of the elastic theory through the analogue has been extended to the assessment of the influence of stoping operations on off-reef excavations. Underground conditions at damaged and undamaged areas have been compared with predicted elastic stresses at the positions under review, resulting in the derivation of design parameters for use in siting off-reef excavations in the prevailing geological conditions in the O.F.S. and Klerksdorp goldfields. The analogue has also been used to assess the vulnerability of certain un mined dykes to bursting. Correlations between stresses induced on dykes by stoping and dyke behaviour underground has enabled critical stress levels to be determined for several persistent dykes occurring in the O.F.S. and Klerksdorp goldfields. A number of long and short term planning projects at mines operating in the Anglo American Corporation and General Mining and Finance Groups are described, where the data derived from the electrical resistance analogue is processed by computer programmes and assessed on the strength of the design factors derived from the correlation of field work and the elastic theory.

Jan 1, 1970

A decision by joint-venture partners Anglo American, Gencor, and the Industrial Development Corporation to proceed with the expansion of the Columbus Stainless Steel plant in Middelburg will contribute significantly towards the economic growth that South Africa needs so desperately. The expanded facility, expected to come on-line in 1995, will be the largest single-plant producer of stainless steel in the world, and the company will rank sixth overall in world production.

Jan 1, 1993

By A. Marek

Reduced downtime and maximized availability of mining machines are the key factors in optimizing production rates. As technology moves industry towards an age of ?intelligent machines? it sets the foundation for change in mining equipment design, functionality, and maintenance. Recent mining machine designs are integrating more and more electronic components into the core functionality of individual piece of equipment due to regulatory and legislative requirements, such as TIER rating, as well as from a safety aspect such as personal detection systems. This paper describes the use of existing on-board electronic equipment to increase machine availability through automated maintenance planning and diagnostic fault-finding capability. The automated maintenance planning takes place on the machine itself in order to be independent of the mine?s infrastructure, while the diagnostic capabilities allow for reduced downtime. The paper also presents a concept to transfer operational data to surface to be able to optimize planning of maintenance and to reduce downtime. Case studies are presented where such systems have been commissioned and are currently in operation, the possibilities of this technology application for the future are examined.

Jan 1, 2012

By D. F. Malan, P. J. Le Roux

Almost no work has been published on the strength of pillars in mines exploiting the LG6/LG6A chromitite bands in the Western Bushveld Complex. The strength of these pillars is unknown, and the hard rock industry still uses the Hedley and Grant formula. Numerical modelling, using inelastic constitutive models, may be of some value in estimating the pillar strength, but this approach is difficult and prone to errors as many assumptions are made. This paper explores the alternative approach of the back-analysis of actual LG6/LG6A mining layouts, using displacement discontinuity codes to simulate the average pillar stresses on a mine-wide scale. From this, and underground observations, a ‘minimum’ pillar strength (K-value in the pillar strength formula) can be estimated. The codes TEXAN and Map3D are both used in the paper to simulate the actual pillar shapes and sizes in an LG6/LG6A mine. The results are encouraging as the two codes produced similar APS values for a complex pillar geometry. An estimated K-value of 77 MPa was determined for the LG6/LG6A pillars in this particular area. This is more or less similar to earlier work done for the UG2 chromitite seam, but higher than the K-value of 39 MPa for a linear formula obtained by other workers for LG6/LG6A pillars. Caution should therefore be exercised before using this higher value for all areas. The effect of element sizes and explicitly simulating the effect of the surface for shallow pillars is illustrated in the manuscript using both codes. The need for actual pillar observations and an iterative design process, which cycles between modelling and observations, is also emphasized.

Nov 27, 2024

By T. Ono, B. Altansukh, S. Kawamura, K. Haga, A. Shibayama, Y. Takasaki

In recent years, the grade of silica in zinc concentrate has increased due to the degradation of zinc content and the increase in impurity content in natural ores. It implies that the development of silica removal technology from zinc concentrate is necessary to solve problems in the smelting process caused by the high content of silica in zinc concentrate. In this paper, the authors investigated the silica removal processes from silica-rich zinc concentrate by mineral processing approaches such as re-grinding and flotation. This study focused on the pulverisation process as a pretreatment for the investigation of individual minerals' liberation from the silica-rich zinc concentrates using different kinds of pulverisers. Flotation experiments were performed to separate silica and zinc concentrate from the pulverizsd feed sample using a pH regulator (NaOH), activator (CuSO4), collecting agent (PAX), and foaming agent (DOW froth 250). Results showed that the liberation rate of silica (SiO2) was reached 75% from 13% by pulverisation in an attritor with a 2 mm ball in diameter, while silica accumulated in a fraction over 20 mm in size. Flotation experiments indicated that silica removal efficiency was achieved by 44% from + 20 mm fraction obtained from pulverisation whereas the grade of silica in froth reached 1.85 mass% from 4.5 mass%. Results indicate that silica could selectively separate from silica-rich zinc concentrate, and 99.8 % zinc recovery is achieved under the studied conditions. Keywords: Zinc concentrate, silica, pulverisation, liberation, sieving, flotation

Jan 1, 2020

By M. Ndabeni, J. H. van Vreden, M. Le Roux, Q. P. Campbell

It is not uncommon for gold slurry ponds or screen oversize dumps to contain several different types of carbon-rich contaminants. These contaminants act as robbers of dissolved gold which has a detrimental effect during the downstream carbon-in-leach (CIL) or carbon-in-pulp (CIP) processes. With a renewed interest in the reprocessing of contaminated gold waste ponds and dumps, preconcentration of the feed to either the CIL or CIP process becomes important to maximise profits from these resources. An added advantage in removing these resources, which were once thought of as being uneconomical, is the availability of land that can further be rehabilitated for community development projects. For gravity separation, an example of suitable technology is the Reflux Classifier (RC), which can be used for the separation of materials of different densities and can be used as a pre-concentration step. In this project, a laboratory-scale Reflux Classifier was used to pre-concentrate a gold-bearing sample obtained from a waste dump situated to the east of Johannesburg, South Africa. The material had an average gold grade of 1.9 g/ton and a carbon content of 10%. This material was first fed to a semi-batch Reflux Classifier that was used to fractionate it into several different density intervals by varying the fluidisation water feed rate, followed by continuous runs at fixed water flow rates. The results showed that a cumulative gold recovery of 60%, carbon recovery of 85%, and mass pull of 41% was possible for a fluidisation water feed rate of 15 L/min, while a rate of 20 L/min resulted in a gold recovery, carbon recovery and mass pull of 83%, 92% and 79% respectively, which translated into a concentrate gold grade above the set target of 3 g/ton. Continuous operation at 20 L/min yielded an underflow stream with 84% gold recovery at a grade of 5.4 g/ton. Keywords: Reflux Classification, gold recovery

Jan 1, 2020

By k. Lebecki, S. Trzcionka

The prototype and test results of the instrument for quick determination of incombustible content in deposited dust as a protection against coal dust explosion propagation are presented. Presently existing methods do not permit to obtain quick information about incombustible content, needed for the proper protection of workings. As the operating principle for the e instrument the dependence of reflection of infrared radiation intensity on incombustible content in the sample is chosen. The construction is based on the modern electronics. The measurement will be done at the sampling site. The range of the instrument is 0-100% of incombustible, direct reading, autonomous supply, weight no more than 0.5 kg, and is intrinsically safe according to EN Standards. During the Conference the instrument will be commercialized.

Jan 1, 2003

By P. N. Harris

The Colloquium on 'Recent Mining and Metallurgical Developments in the Orange Free State' was held at the Civic Centre in Welkom on the 4th and 5th May, 1983. The Chairman of the Orange Free StatejKlerksdorp Branch of the Institute and Acting General Manager of Unisel Gold Mining Company, Mr D. A. Parfitt, opened the proceedings, and Professor A. N. Brown gave the welcoming address. Mechanization of mining The South African Institute of Mining and Metallurgy is to hold a one-day colloquium on 'Developments in the Mechanization of Mining Operations' during September 1984. Surfac,e mining and quarrying The Second International Surface Mining and Quarrying Symposium is being organized by The Institution of Mining and Metallurgy in association with the Institute of Quarrying.

Jan 1, 1983

By Donald J. Murdock

Column flotation has been developed over the past ten years as an alternative to conventional flotation. It has been used mainly in the cleaning applications of sulphide flotation, where its ability to wash the froth of entrained gangue and produce a higher-grade product has given it a distinct advantage over other technology. The benefits of column flotation can be summarized as follows: Improved concentrate gradeby 2 to 5 per cent . Significantly lower operating costs . Savings in capital investment . Superior control. Since the initial development of the equipment, a number of design improvements have been developed that now form the basis of the Cominco column-cell design. The purpose of this article is to discuss some of those design innovations, and present some typical industrial results.

Jan 1, 1991

By A. H. Mokken, G. K. I. Blendulf, G. J. C. Young

A study of the arrangements for pulp discharge on pebble mills, and their influence on mill performance by A. H. MOKKEN, B.Sc. (Eng.) (Rand) (Fellow), G. K. I. BLENDULF, M.Sc. (Stockholm) (Member), and G. J. C. YOUNG, B.Sc. (London) (Member) Although used for many years in the gold-mining industry, the conventional pan lifter at the discharge end of a pebble mill has hindered attempts at optimization of speed of rotation and pulp flow. A theoretical approach to flow patterns in pan lifters has pointed to limitations in the capacity of these lifters, with capacity decreasing as speed of rotation is increased. Complete elimination of the pan lifter by the adoption of peripheral or end discharge has resulted in a marked increase in pulp flow and an improvement in power utilization. Assays of the gold content of pulp discharged after a mill stoppage from mills fitted with pan lifters show values well in excess of the current milled grade, which indicates an accumulation of gold particles in the mill and, therefore, a longer retention period. The same could apply to other heavy minerals and metals present in the ore feed or worn off mill linings and metallic grinding media. Examples are osmiridium, fine iron and iron alloys, and copper and sulphide minerals. This phenomenon is attributed to the higher specific gravities of these metals and minerals, causing them to migrate towards the mill shell, from which position they are not readily removed by the lifters at the discharge end of the mill. The close association of gold particles with iron and sulphide minerals in the crevices of mill liners might be conducive to the formation of coatings on the gold. Assays of samples of milled pulp taken from a mill designed for end discharge show a lower accumulation of gold. The accumulation and nature of these gold particles are being studied at present. With increasing diameters of pebble (or autogenous) mills, peripheral or end discharge appears to be the preferred method of pulp removal.

Jan 5, 1975

By J. D. Swanepoel, S. Horn, C. J. Badenhorst

Diesel particulate matter (DPM) is the particulate component of diesel exhaust, which includes diesel soot and aerosols. When released into the atmosphere, DPM can take the form of individual particles or chain aggregates, with most in the invisible sub-micrometer range of 100 nanometres. The main particulate fraction of diesel exhaust consists of fine particles and because of their small size, inhaled particles may easily penetrate deep into the lungs. The rough surfaces of these particles make it easy for them to bind with other toxins in the environment, thus increasing the hazards of particle inhalation. DPM is a significant health hazard in underground mining operations, where the use of dieselpowered equipment in confined spaces can lead to high levels of exposure among people working in these environments. Classified as a carcinogen by the International Agency for Research on Cancer (IARC), DPM has been linked to severe health effects, including respiratory and cardiovascular diseases, as well as an increased risk of lung cancer. Effective management of DPM is essential not only for protecting people’s health but also for ensuring regulatory compliance, maintaining operational efficiency, and safeguarding the long-term viability of mining companies.

Mar 5, 2025

By S. Northey, N. Haque, S. Stoddart, W. Bruckard

Development of new technologies and procedures for managing mineral residues and wastes may benefit from a clear understanding of existing tailing management practices. There is a considerable variability in tailing management techniques used in the Australian copper and gold operations, with associated differences and flow-on effects for the mine site water balance. A database was created, capturing a total of 41 copper and gold processing operations in Australia. The database provides information on tailing generation rates, tailing properties (solids contents and particle size distributions) and tailing storage facility (TSF) types and configurations (e.g. total TSF surface area and wetted surface area). Significant variability was found for the above-mentioned parameters. The solid tailing generation rates ranged from 0.5-37 Mt per annum in 2015. Furthermore, both the solids contents and particle size ranges of the tailing were highly site-specific, and largely dependent on the processing flowsheets. Solids contents of tailings ranged from 45-74% by weight whilst P80 sizes of the concentrator (flotation) feed varied from 75-185 μm. The estimated pumping distance was up to 15 km. The presented data can potentially be used to better tailing management strategies by estimating the potential recoverable water and recycling it, thereby thus reducing tailing footprints. Keywords: Tailing management, tailing storage facility, water balance, mine site, flowsheeting

Jan 1, 2020