Search Documents

By A. F. Lee

Dr E. C. Hanekom (Visitor): Two years ago we used the bubble pick-up technique as developed at Anglo American Corporation for screening candidate flotation agents prepared in our laboratories. It was obviously necessary to know to what extent the technique gave reproducible results and a statistical evaluation of the test method was made using a mineral sample provided by Anglo American Corporation. A bubble of 2.0 mm diameter was used and the measuring graticule was divided into squares (units) with sides of 5.0 mm at 25 X magnification. The mineral granules had diameters from 53 to 74 mm. The bubble was loaded by depressing it against a layer of mineral grains to give an arbitrary but constant compression of 0.4-0.5 mm. It was rolled five times through 2 mm horizontal displacement. The bubble was then lifted, its load compacted by gently stirring and the projected area measured in squares (units) on the grid. Each substance was tested at 5 ppm concentration in distilled water at five points in the pH range 3-6. With these standardized conditions of operation the reproducibility of the test was studied. Four materials were tested and at each pH value the procedure of forming a bubble, picking up granules and counting the units was repeated ten times. From these results the standard deviation for a single count at any pH value was calculated for each material (Table 1. The coefficient of variation of approximately 3 per cent was relatively low and it was decided that further refinements in the counting procedure would be of doubtful benefit with the present apparatus. Similar experiments were carried out with 12 sample materials. In this case the bubble formation and pick-up were repeated four times at each pH value, the mean value was calculated for each set of four observations and final pick-up values for the materials were obtained by selecting the highest mean count. Each test was completely repeated a number of times as indicated in Table 2 and the standard deviation calculated. The results allowed the selection of the more promising materials and the rejection of poor performers at the 95 per cent confidence level. All tests were carried out by one operator. Some evidence was obtained that the method is sensitive to operator bias. In conclusion it can be said that from all the results analyzed it would appear that once operation conditions are fixed (viz operator, pH control) the precision of the method is adequate. The author wishes to thank Messrs African Explosives and Chemical Industries Limited for permission to publish these data. G. S. Stander and C. J. Kooij (Visitors): We must congratulate Mr Lee for this most interesting and useful development of the pick-up experimental method. It certainly provides research workers with an instrument which makes flotation more of a science and less of an art. We visited Mr Lee at his laboratory where he gave us a demonstration of the bubble pick-up instrument and technique as developed and improved by him.

Jan 12, 1969

Caving is the lowest cost underground mining method provided that the draw point spacing, draw point size, and ore-handling facilities are designed to suit the caved material, and that the draw point horizon can be maintained for the life of the draw. In the near future, several open-pit mines that produce more than 50 kt per day will have to examine the feasibility of converting to low-cost, large-scale underground operations. Several other large scale, low-grade underground operations will experience major changes in their mining environments as large dropdowns are implemented These changes demand a more realistic approach to mine planning than in the past, where existing operations have been projected to increased depths with little consideration of the change in mining environment that will occur. As economics force the consideration of underground mining of large, competent ore bodies by low-cost methods, the role of cave mining will have to be defined In the past, caving was generally considered for rockmasses that cave and fragment readily. The ability to define cavability and fragmentation, the availability of large, robust load-haul-dump units, a better understanding of draw-control requirements, improved drilling equipment for secondary blasting, and reliable cost data have shown that competent orebodies with coarse fragmentation can be exploited by cave mining at a much lower cost than by drill-and blast methods.

Jan 1, 1994

By L. A. Vermeulen

A simple argument shows that it is impossible for the flight of a rod in contact with a litter bar in a rotary mill to be initiated at that point on the upside of mill rotation when all the forces acting on the rod are in equilibrium. The argument was confirmed experimentally in a study showing that the lift of litter bars is a function of their height, that the rod velocity at the point of departure has a significant radial component, and that the subsequent flight of a rod is along a parabolic trajectory as predicted by elementary mechanics. A quantitative account of the observed effects, which is based on a dynamic theory of the sliding interaction between rods and litter bars, revealed interesting properties of the motions of rods down the surfaces of litter bars when the latter are in uniform circular motion during the rotation of a mill.

Jan 1, 1985

By A. Muller

The magnesia-carbon refractories used in the ConArc process experience severe wear as a result of the varying slag composition during the blowing phase. This work determines the basicity range in which minimum as well as maximum refractory wear was experienced by the magnesia-carbon refractories during service. In order to determine an optimum slag composition, the crucible test in an induction furnace was used. The magnesia-carbon refractory bricks were cut into cylindrical crucibles to which a synthetic slag in the form of pellets was added. The basicity (B2) of the slag was varied from 0.5 to 3. Tests were done at 1 600°C for one hour. Apart from the crucible test in an induction furnace, visual inspection and SEM analysis were also done to investigate the corrosion mechanism. FACTSage® predictions about the interaction between refractories and slag were also done. These predictions were compared to the actual results attained. It was found that the extent of corrosion by slag attack decreases as the basicity increases. The most severe corrosion of the MgO-C refractories occurred at a basicity of 0.5 whereas the optimum basicity is above 2.0. SEM analysis indicated severe slag attack at the lower basicities with no visible refractory-slag interaction at higher basicities. TheFACTSage® predictions supported most of the actual findings. Keywords Magnesia-carbon, ConArc, blowing phase, slag resistance, induction furnace, crucibles.

Jan 1, 2011

ERRATA-AUTHOR'S REPLY IN SEPTEMBER, 1970, JOURNAL: PAGE 52 I. Left half of the page, 4th paragraph, fifth line from the bottom: for 22 / 5 1/2 %, read 22 / 5 1/2 %. 2. Right half of the page, fifth paragraph from the bottom, third line from the bottom: for N(l - p), read N(1 - p)x. 3. Right half of the page, fourth paragraph from the bottom, second line: for: at time t after time zero, read: at time x after time zero. NOTICE TO ALL STUDENT MEMBERS OF THE SOUTH AFRICAN INSTITUTE OF MINING AND METALLURGY The Institute offers each year for competition among Student Members of the Institute a prize, or prizes, should entries so warrant it, of up to the value of R100 to be awarded to the Student Member or Members who submit the best paper or dissertation on a topic appropriate to the interests of the Institute. In the case of Student Members who are in full time study at a university the dissertation or thesis which they may have to write in part fulfilment of their university curriculum may be accepted provided it is presented in a manner and on a topic suitable for publication in the Journal. The closing date for the receipt of papers shall be 31st December each year.

By T. Könighofer

Processing of copper-cobalt orebodies in Africa?s Copper Belt has received much recent attention with various flowsheet options being developed specifically for the refining of cobalt. The upfront leach and copper refining routes are well understood whereas the refining of cobalt is more complex, requiring numerous impurity removal steps to produce high purity metal. This paper describes an investigation into one of the possible processing steps in the refining of cobalt, namely, cobalt solvent extraction. The paper emphasizes the importance of upstream impurity removal to achieve the required cobalt solvent extraction feed composition. 18% (v/v) Cyanex 272 in an aliphatic diluents is used as the organic phase. The pH profiles in the various stages are evaluated in order to obtain a raffinate containing <10mg/l cobalt and with a low magnesium content reporting to the stripping section. The pH profile is also used to minimize the impurity deportment to the cobalt electrolyte. The effect of adding a pre-neutralization stage before feeding the organic phase to the extraction circuit is investigated. Zinc build-up in the stripping stages is also looked at. It is recommended for the purpose of this study that four extraction stages at an O:A ratio of 1 with a pH profile from 4.9 to 5.7 be employed. The pH is controlled with 40g/l NaOH. A pre-neutralization stage is required, where the organic phase is contacted with 10 M NaOH. Two scrubbing stages are recommended at an O:A ratio of 40, using the cobalt electrowinning advance electrolyte as the scrub liquor. Three strip stages are to be employed at an O:A ratio of 0.67.

Jan 1, 2009

By Z. Khan

Iron, in the form of steel and stainless steel, is the most commonly used metal in the world. Plain steels corrode and oxidize easily, while stainless steels exhibit improved corrosion and oxidation resistance. It has been found that rare earth metal (REM) additions, such as cerium and erbium, result in the improvement of the abovementioned properties in iron-containing compounds. Gadolinium is a REM, however, there is very little information available on the influence of gadolinium on the microstructure and mechanical properties of iron-containing compounds. Thus, the purpose of this research project was to determine the influence of gadolinium additions on the microstructure and mechanical properties of mild steel and 316 stainless steel. Ten alloys were produced for the purposes of this research. Five of the alloys had a base composition of mild steel while the remaining five had base composition of 316 stainless steel. The alloys for each of the base composition contained gadolinium additions of 0.1, 0.5, 1.2, and 5 weight per cent. The as-cast and the cold-rolled alloys were analysed. The alloys responded well to the cold-rolling with the exception of the 5 weight per cent gadolinium mild steel and stainless steel alloys. These alloys were extremely brittle and underwent a significant amount of cracking during the cold rolling process. A microstructural analysis of the alloys was conducted using a light optical microscope, while the chemical analysis of the alloys was conducted using energy dispersive x-ray spectroscopy (EDS). The resulting microstructures and EDS analyses revealed that the gadolinium displayed minimal solubility in the ferrite matrix of the mild steel alloys and minimal solubility in the austenite matrix of the stainless steel alloys. Instead the gadolinium formed as an interdendritic secondary phase in both alloys. EDS analysis revealed that the secondary phase in both alloys was gadolinium-rich. Vickers microhardness tests conducted on both alloys revealed that the alloys were composite-like, with a hard, brittle gadolinium-containing compound dispersed throughout a softer, more ductile matrix. The corrosion resistance of the alloys was determined through potentiodynamic anodic polarization tests. Two solutions were used for the corrosion rate tests: a 0.5 weight per cent NaC1 solution and a 0.5 M H2SO4 solution. The results from the mild steel alloys revealed that in both the solutions, the corrosion potentials and the corrosion resistance of the alloys increased with increasing gadolinium concentration up to 1 weight per cent. The corrosion rate test results from the stainless steel alloys revealed that the passivation current density and corrosion resistance of the alloys increased with increasing gadolinium concentration in both solutions. The oxidation resistances of the mild steel and stainless steel alloys were determined through the use of a Netzstch Simultaneous Thermal Analyser. For both the mild steel and the stainless steel alloys, it was found that the oxidation resistance of the alloys increased as the concentration of gadolinium increased when compared to the as-received mild steel and stainless steel samples. This could be due to a strongly adhering gadolinium oxide scale that formed on the surface of the alloys and resulted in the protection of the mild steel and the stainless steel.

Jan 1, 2012

By E. Lwamba

The aim of this study was to examine the effect of grain size distribution control of the raw material mixture on the permeability of the green sinter bed and the properties of the produced sinter. This was achieved by evaluating the granulation characteristics of the sinter mixture (moisture content, granulation time and mean granule diameter) in terms of its green bed permeability, and evaluating the productivity of the sinter bed, the coke rate, tumble index (TI), abrasion index (AI), reduction disintegration index(RDI) and reducibility (RI) of the produced sinter. The raw sinter mixtures contained combinations of Thabazimbi iron ore, Sishen iron ore, coke, lime and return fines. The grain size distributions were controlled by removing the ?0.5 mm size fractions of the return fines and coke, and the ?1 mm size fraction of lime. Of the examined mixtures, a mixture of 20 mass% Thabazimbi iron ore, 80 mass% Sishen iron ore and fluxes where the coke, lime and return fines were all sized had the highest granulation effectiveness and permeability. The sintering properties of the mixtures in which the grain size distributions were controlled, were very similar for all the mixtures, but superior to the base case mixture in which the grain size distribution was not controlled. Keywords: Thabazimbi iron ore; Sishen iron ore; granulation, permeability, grain size distribution; sinter.

Jan 1, 2008

By Mike Rogers

Platinum production in Southern Africa amounted to 80% of world production in 2005with a small increase from 5 117 000 ounces to 5 275 000 ounces. For the seventh consecutive year the platinum market is on course to record a moderate deficit in supply. This is reflected in the price increase from a trading range US$860 to US$880 in June 2005 to an excess of US$1 200 in September 2006. Southern Africa, with its extensive platinum reserves, will continue to be the dominant platinum producer and has a number of new mines in an advanced stage of planning. The slogan ?Platinum Surges Ahead? was selected to describe the exciting and vibrantnature of all aspects of platinum mining, beneficiation and marketing. This conference will cover these aspects from exploration and orebody delineation, through mine design, development and operation to mine closure; mineral beneficiation, marketing and compliance with the Mining Charter will also be subjects for discussion and debate. It is also anticipated that the issue of overall increases in productivity, through the introduction of technology, will demonstrate Southern Africa?s status as a premier mining district. It is my pleasure to welcome delegates from abroad and locally, on behalf of the SAIMM, to the Second International Platinum Conference ?Platinum Surges Ahead?. I trust that you will find the proceedings informative and value adding and will participate in the discussions and debate in order to obtain maximum benefit from the conference. I am sure that the post-conference tours will be interesting and of great benefit to participants. Finally, a big word of thanks to the members of the Organising Committee, the management and staff of the SAIMM, and to our willing sponsors, without all of whom this conference would not have been possible.

Jan 1, 2006

By R. Thomas

A Honeywell TDC 2000 central process control system was installed at Rössing in 1984. The system controls the metallurgical operations from crushing to the finished product of uranium oxide and manufacture of sulphuric acid. The operation was previously controlled from nine separate local control rooms. The paper briefly reviews the design and commissioning of the control system on an operating plant and discusses the impact on manpower organisation and training needs. Development of the process control system during its first two years of operation is reviewed and a summary is given of the current status of computer control at Rössing. The impact of the new system on overall plant operation and performance efficiency is also briefly described. In conclusion, future developments of computer control and overall optimisation of metallurgical operations are reviewed.

Jan 1, 1987

By Matthew D. Viergutz

MECS? HRS technology has reliably recovered intermediate pressure steam from sulphuric acid plants for more than 20 years. This steam can either generate electricity or replace steam produced by an existing fuel-fired boiler. As worldwide greenhouse gas emissions continue to rise, industries are looking for novel and cost effective solutions to reduce pollution, particularly carbon dioxide, from their plants. Waste heat recovery technologies such as HRS offer new and existing plants the opportunity to maximize energy efficiency while reducing their reliance on energy supply from external sources. This paper offers a unique look at energy recovery in sulphuric acid plants and how recent innovations in MECS? Heat Recovery System technology make HRS more financially viable ? and more green - than ever.

Jan 1, 2009

By I. C. R. Gilchrist

A principal requirement in the design of a backfill transportation pipeline is the accurate prediction of the values of key slurry flow parameters. Input variables, such as particle size and solids concentration, are usually determined by the load-bearing requirements of the placed fill. It is therefore necessary to identify the optimum conditions of transport for a particular combination of input variables. This paper critically reviews the methods available to predict the values of flow parameters in slurry pipeline systems in the light of experimental data generated at a test facility. Particular reference is made to rod milled waste and deslimed tailings transport systems and, in the case of the former, it is shown that both pumping and load-bearing requirements can be optimized.

Jan 1, 1988

By F. S. Beretta

Mineral processing efficiency depends on various factors and among them includes head grade fluctuations feeding the processing plant. Head grades can fluctuate beyond an admissible range, implying in recovery decrease for the mineral of interest. Grades feeding the processing plant depend on the geological domain which is being mined and on the mining schedule. Therefore, it is necessary to keep grade variability controlled. Blending piles are an efficient alternative to reduce grade fluctuations. The main factors influencing blending efficiency are the pile size or its mass and the number of layers used to pile up. Large piles are more efficient to reduce variability, however, there are economical and operational limits associated with them. This study investigates a methodology to analyse the ideal pile size to reach an acceptable variability given the in situ grade fluctuations. Geostatistical simulations provide the means to assess grade variability using an optimized mining schedule. These block grades are used to simulate any given pile throughout the mine`s life. The methodology was illustrated using a case study to control coal ash content at a mine supplying ROM coal to a power plant. Keywords: homogenization, piles, geostatistical simulation.

Jan 1, 2009

By Matthew D. Viergutz

MECS? HRS technology has reliably recovered intermediate pressure steam from sulphuric acid plants for more than 20 years. This steam can either generate electricity or replace steam produced by an existing fuel-fired boiler. As worldwide greenhouse gas emissions continue to rise, industries are looking for novel and cost effective solutions to reduce pollution, particularly carbon dioxide, from their plants. Waste heat recovery technologies such as HRS offer new and existing plants the opportunity to maximize energy efficiency while reducing their reliance on energy supply from external sources. This paper offers a unique look at energy recovery in sulphuric acid plants and how recent innovations in MECS? Heat Recovery System technology make HRS more financially viable ? and more green - than ever.

Jan 1, 2009

By L. H. Lindstad

The paper reviews the tapping process and the major wear mechanisms on the tap-hole, including wear from tapping tools. Measured temperatures in different tap-holes are related to choice of binder and material for repair pastes. The strength and disadvantage of carbon and silicon carbide materials are compared. Normal daily and weekly maintenance of tapholes is described, together with the major repairs that are done during longer furnace shutdowns. The objective is to show that the type of repair and repair material needs to be adapted to each individual furnace.

Jan 1, 2014

By E. L. J. Kleynhans, J. I. J. Fick, J. P. Beukes, P. G. van Zyl

"Ferrochrome (FeCr) is vital for the production of stainless and high-alloy ferritic steels, since it is the only source of new Cr units. FeCr production is an energy-intensive process. The pelletized chromite prereduction process is most likely the FeCr production process with the lowest specific electricity consumption (SEC), i.e. MWh/t, currently in operation. However, due to increases in costs, efficiency, and environmental pressures, FeCr producers are attempting to lower their overall energy consumption even further. Recently, it was proven that pre-oxidation of chromite ore prior to pelletization and prereduction significantly decreases both the SEC and lumpy carbonaceous reductants required for smelting. This paper presents the first attempt at conceptualizing the technoeconomic feasibility of integrating chromite pre-oxidation into the prereduction process. Financial modelling yielded a net present value (NPV) at a 10% discount rate of approximately R900 million and an internal rate of return (IRR) of approximatelyy 30.5% after tax, suggesting that the implementation of pre-oxidation prior to pellet prereduction may be financially viable. Sensitivity analysis indicated that the parameter with the greatest influence on project NPV and IRR is the level of prereduction. This indicates that the relationship between maintaining the optimum pre-oxidation temperature and the degree of prereduction is critical for maximium process efficiency. IntroductionStainless steel is a crucial alloy in modern society. Virgin chromium (Cr) units used in the manufacturing of stainless steel are obtained from ferrochrome (FeCr) – a relatively crude alloy consisting predominantly of Cr and iron (Fe) (Murthy, Tripathy, and Kumar, 2011; Beukes, van Zyl, and Ras, 2012). FeCr is produced mainly by the carbothermic reduction of chromite ore in submerged arc furnaces (SAFs) and direct current arc furnaces (DCFs) (Neizel et al., 2013; Beukes, Dawson, and van Zyl, 2010; Dwarapudi et al., 2013). The energy required to heat, smelt, and reduce the chromite ore to the metallized state is supplied by electricity (Pan, 2013). FeCr production is an energy-intensive process, with a specific electricity consumption (SEC) varying from 2.4 MWh/t to more than 4.0 MWh/t FeCr produced, depending on the process applied (Pan, 2013; Neizel et al., 2013). Daavittila, Honkaniemi, and Jokinen (2004) stated that the typical operational costs of FeCr smelters can be divided into four categories, i.e. chromite ore (30%), carbonaceous reductant (20%), electricity (30%), and other production costs (20%). This makes electricity consumption the joint largest factor that influences operational costs in FeCr production."

Jan 1, 2017

By P. Gonzalez

Minera La Parreña, S.A. de C.V., Milpillas operation is an underground mine designed to process 8 352 tons of ore per day for the recovery of copper through crushing, heap leaching, solvent extraction and electrowinning facilities. In order to optimize copper recovery during leaching, the ore is crushed to 13 mm and subjected to primary sampling every 15 minutes for metallurgical accounting. At the same particle size, primary sample goes to secondary sampling and then, the secondary sample is crushed to 2 mm before tertiary sampling. The tertiary sample is sent to laboratory where a final sample is obtained and pulverized to 106 microns for copper assay. This paper shows a review of sampling strategy focused on minimizing or eliminating sampling errors and an experiment designed to determine copper head grade profile as well as the best sampling frequency.

Jan 1, 2009

By X. Ndlovu

Underground observations in a coal mine have indicated failure oft he immediate roof above the bords. Careful observations and photographic recording of occurrences of these roof failures, termed ?roof guttering?, have been made. The occurrence of guttering results directly in roof instability, and indirectly, due to the interaction of the guttering with natural planes of weaknesses in the immediate roof rock. In this paper, relevant observations of roof guttering, possible mechanisms of formation of roof gutters, laboratory testing for determination of material strength and deformation properties, and numerical analyses to explain underground observations are described. Mapping of roof failures showed that these took place mainly towards the centre of the roadways. Roof guttering was observed often to occur violently and with little warning. Occurrence of roof guttering has a negative impact on production?some panels are abandoned, production times are increased and safety of workers is compromised. The numerical stress analyses showed that, although none of the constitutive behaviour criteria used predicted the observed underground failures correctly, the extension strain criterion gave the best agreement.

Jan 1, 2007

Metso Minerals Cisa have developed VisiofrothTM - a system which calculates parameters of the froth surface using vision from remote cameras mounted about individual flotation cells. The parameters calculated from this system can be utilised within process control strategies to achieve stabilisation or optimisation of the flotation process. As part of a JKMRC AMIRA P9 field campaign, froth vision was collected from various cells operated at different air rates and froth depths within Rio Tinto&apos;s Northparkes copper roughing and scavenging circuit. At the same time, samples were collected to determine the cell metallurgical performance at each operating condition. These froth images have been processed using the VisiofrothTM system with froth velocity, bubble size, froth collapse rate and various froth colour parameters calculated. These parameters have been compared to the measured concentrate flow and concentrate grade produced at each condition. This analysis shows that the concentrate tonnage flow is strongly correlated with froth velocity whereas the concentrate grade is best correlated using froth velocity in combination with a bubble stability parameter which affects the bubble size distribution on the top surface of the froth. This paper summarises the results from this analysis as well as an overview of the VisiofrothTM system and the parameters that are measured by the software.

Jan 1, 2007

This paper describes the extraction of gold, as the anionic aurocyanide complex, from solution by strong- and weakbase anion-exchange resins. The effects, on the rate of extraction and the loading capacity for gold, of parameters such as pH, temperature, ionic strength, agitation, and the presence of competing anions are reported. The elution and regeneration of strong- and weak-base resins will be examined in a second paper. A third paper in this series will present the results of several smallscale pilot-plant investigations carried out with strong- and weakbase resins In cyanide pulps from various South African gold mines, and will compare the metallurgical performance of resin-In-pulp with that of the carbon-in-pulp process.

Jan 1, 1984