Search Documents

By C. Snyman, M. Le Roux, Q. P. Campbell, S. Engelbrecht

Due to the ultrafine particle size required for effective processing of chromite ores, dewatering of the concentrates presents a challenge. It is not uncommon for the ore to have elevated moisture contents even after dewatering, which must be reduced to required levels of between 8% and 10% by mass for further processing. Contact sorption drying has shown promise in test work on fine coal. This method was used to study the dewatering of chromite on a laboratory scale using 3 mm spherical activated alumina ceramic beads as a sorbent. Three different sorbent-to-chromite mass ratios, namely 0.5:1, 1:1, and 2:1, were tested with different process conditions, including dewatering in a stationary and a rotatingl bed. The experimental work showed that it was possible to achieve the target moistures in less than 10 minutes, irrespective of the sorbent-to-chromite ratio used. Ratios of 1:1 or higher, however, proved to be the best. The sorbent reusability at mass ratios of 1:1 and 2:1 were therefore tested. With a 1:1 mass ratio, the sorbents could be reused for three cycles, while with 2:1 ratio, the number of cycles increased to six. The sorbent-to-chromite mass ratio used had a significant influence on the required contact time and the reusability of the sorbents.

Oct 3, 2023

By M. Arlandi-Rodríguez, and A. García-Berrocal, A. Alonso-Jiménez, C. Lopez-Jimeno

Spain is a major producer of dimension stone, which is one of the most important industrial sectors in the northwest of Spain. This justifies the maintenance of these industries, although the technical and environmental requirements for their continuity are increasingly demanding. The main target of this paper is to present a new methodology in order to obtain k-ratio stress values on the basis of flat jack measurements and finite element numerical back- analysis with Rocscience© RS2 software. Continuous iterations were performed to try to find a relationship between the k₀ and the measured stress in the tunnel roof and sidewalls. It focuses on technical aspects of the method for designing mine chambers in the slate industry that were previously mined by open pit methods. The size of the chambers impacts the operating cost, and the dimensioning of a correct support ensures better efficiency and safety. Correct knowledge of the k₀ therefore is critical for the design of the support. The proposed new method entails a simplification of the classical procedure for estimating the k-ratio.

Sep 1, 2022

By D. Bessinger, J. Rabe, J. Zietsman, C. Coetzee, P. H. Lamont, J. Muller

The UCAR® CHILL-KOTE? freeze lining concept combines wall cooling with carbon and graphite refractories of higher thermal conductivities to ?chill? the refractory lining by transferring heat from the refractory lining. Effective sidewall water cooling, together with the efficiency of the heat dissipating conductive refractories, lowers the temperature of the lining to below that of the molten process materials. This causes a layer of slag and process metal to solidify or ?freeze? and form a protective ?skull? which completely coats the refractory hot face. Once formed, the slag skull insulates the refractories, reducing heat loss and protect the lining from erosion, chemical attack, thermal shock, and other stresses. The result: extended life and greatly improved refractory performance. The Ilmenite smelting process depends on the presence of a solidified slag skull to protect sidewall refractory material from chemical attach by molten slag. No known refractory material is able to withstand this corrosive material. To date, UCAR has not applied their Chill Kote ? technology in the ilmenite smelting industry. This paper revolves around the results obtained from conducting an ilmenite smelting campaign on a 500kW DC open-arc furnace with a UCAR designed refractory system. The purpose of this test was to establish the effects such a lining has on refractory wear and the reduction-smelting process. Proper thermo-couple management enabled the authors to monitor lining wear for the duration of the campaign. Prior to the pilot-scale campaign, modeling work was completed to evaluate the feasibility of applying UCAR® CHILL-KOTE? technology to ilmenite smelting furnaces. The successful operation of a pilot-scale furnace equipped with the UCAR® CHILL-KOTE? lining as well as concise modeling suggest that it should be a viable option to consider for an industrial-scale furnace.

Jan 1, 2007

By D. Odendaal, S. Bharat, R. D. Cromarty

The aim of this investigation was to determine the effect of high-temperature heat treatment on the electrical resistivity of charcoal. Samples of two different wood types (eucalyptus and black wattle) were pyrolised in a retort at a temperature of 700°C and the resulting charcoals heat-treated in an induction furnace at temperatures from 800°C to 1800°C and residence times from 60 to 120 minutes. After cooling, the resistivities of the samples were measured at room temperature using the four-point probe technique. It was found that as the heat treatment temperature increased the electrical resistivity of the charcoal decreased, approaching an asymptotic value at higher temperatures. Longer residence times decreased the resistivity, but this effect was not pronounced.

Oct 3, 2023

By M. Splaine, W. Davison, D. C. Atkinson

"Since 1964, Nchanga Consolidated Copper Mines, Ltd., has been developing and using production scheduling methods for optimizing its metallurgical operations in the short term (up to one year). Medium-range metallurgical planning has been possible only by successive evaluations of a single-year L.P. A modified version of Rosenbrock's direct search technique has now been developed to allow multi-year optimization of both mining and metallurgy for medium-range planning. The modifications to the search technique have produced a marked increase in computational efffciency for this heavily constrained problem in many variables and the system is a usable planning tool, given a reasonably powerful computer. The plans are 'optimum' in the sense that they yield the maximum present value of the operations.Each of the resulting five-yearly mine plans forms the basis for further detailed metallurgical evaluation by the established production scheduling system."

Jan 1, 2014

By Nicolle Krusberski

Potential errors in XRF analysis are discussed and investigated with specific reference to the analysis of ilmenite samples. A selection of ilmenite samples was chosen and prepared using two XRF preparation techniques: pressed powder pellet and unroasted fusion bead. The merits of the two methods have been discussed in this paper for ilmenite analysis by XRF. Recommendations have been made regarding the use of pressed powder pellets especially with regard to the mineralogical effects that were evidenced during this investigation. The fusion bead technique was found to be far more accurate and able to meet short turnaround requirements provided the calibration methodology used is specific to the grade of samples analyzed.

Jan 1, 2014

"Chairman: Prof A. E. H. BLEKSLEY Rapporteur: Prof J. ELBRONDPanel Members: Prof J. C. Griffiths, Prof T. E. Hawkins, Mr A. C. Langton, Mr M. Splaine, Mr A. WeissThe reasons for failure of computer applications in the mineral industry and the direction of future developments.The Chairman opened the discussion by elaborating on the disappointment felt by some authorities with the lack of progress in the application of computers in the mineral industry during the last ten years, and posed the question to the panel : 'Do you agree that the computer age has not come up to expectations?'Mr Langton said that although there seemed to be a tremendous amount of brainpower applied to the theoretical side, he thought that the production men had not got all the help from computers that could have been given to them. The computer, said Prof Griffiths, is as yet a new tool which should not be used to do old things in old ways. To learn to use the computer will take time. After all, he said, it had taken 400 years after the introduction of the printing press to achieve general literacy, and perhaps it will take 40 years after the introduction of the computer to achieve `numeracy'.In Mr Weiss' view, the reason for the feeling of disappoint¬ment lay in the focussing of attention on the computer. The blame, if any, lay with the people surrounding the computer, that is, the analysts and programmers, to whom the emphasis should be shifted.Prof Hawkins said that he thought that some applications of the computer in the mineral industry had been successful, such as, for example, the compilation of payrolls. Reasons for failures in other areas were to be sought in the fact that the people connected with computers had failed to realise that they were merely part of a system. They had not understood the power structure of the organization which their work tended to change, and were therefore not prepared for the inevitable conflict with the production men.In Mr Splaine's view the production man had not received the assistance he could have had from the computer people because he may possibly not have allowed this to happen.Prof Bleksley concluded from these opinions that the promise which computers had ton years ago had not been fulfilled and added that the opinions expressed by the panel had intruded on his next question which was: 'Is the reason for this that people are involved?Prof Hawkins elaborated on his previous theme, namely, that of computer people in relation to management. Com-puter people, he said, were trying to impose change on management but were not prepared to share the responsibility for these changes. In fact, they wanted their work to be distinct and separate, and, as far as management was concerned, changes would be made when management believed that these would be less agonizing than no change at all."

Jan 1, 2014

By S. T. Johansen, B. T. Løvfall, T. Rodriguez Duran, J. Zoric

A methodology for building pragmatic physics-based models is here adapted to predict the erosion of ladle linings in the steel industry, in order to support operators when deciding whether the lining can be used safely for another heat. A defective lining may allow 140 t of molten steel to spill, with disastrous consequences for workers and plant. The adopted work flow for the development, challenges faced, and some model results are presented. One key learning outcome is that model development should allow time for maturing the process understanding, as well as for many iterations by ‘questions-responses and actions’ at various stages in the model development. Good interaction between the development team and industry case owner is an important success factor. Combining or extending the model with the use of machine learning and cognition-related methods, such as knowledge graphs and self-adaptive algorithms, is discussed.

Apr 16, 2024

By B. Mbuya, A. F. Mulaba-Bafubianda, J. M. Mvita

The paper explains the main effects of input leaching parameters, such as addition of a reducing agent, acidity, agitation, temperature, and leaching system potential, in relation to observed and predicted yields of sought-after cobalt. An artificial neural network coupled with graphical probability networks was developed wherein the abovementioned input parameters were used to predict the percentage of dissolved cobalt. Furthermore, similarities and differences between the Bayesian and neural network approaches in terms of their key outcomes are compared with respect to study of the dissolution of cobalt in sulfuric acid. Key results indicate that there is a need to use neural network results to predict conditions for dissolution of cobalt, while using Bayesian network to explain inferences about conditions of the input parameters, thereby achieving realistic predictions.

Jan 1, 2023

By G. A. Bezuidenhout, J. P. T. Kapusta, D. K. Chibwe

"Peirce-Smith converters (PSCs) are extensively used in the copper, nickel, and platinum group metals industries to remove iron and sulphur from the molten matte phase. This technology has not changed significantly since its inception in the early 20th century. The typical converting operation involves lateral purging of air/oxygen-enriched air into molten matte through a bank of tuyeres. This blowing operation occurs at low air pressure from the blowers, and the induced bubbling regime is considered inefficient from both a process and an energy utilization perspective. Inherent drawbacks include recurrent tuyere blockage, inevitable tuyere punching operation to clear airways, and low oxygen efficiency as a result of substantial air losses due to leakages.Investigations in the 1980s demonstrated1 that jetting into Cu and Ni converters could reduce or eliminate some of the process difficulties. In spite of these findings, very little progress has been made in the application of these concepts for converting of non-ferrous melts on a commercial scale.As part of its operational improvement and energy reduction initiative, Western Platinum embarked on a full-scale industrial evaluation of generating a jetting regime by using sonic injection. Prior to full-scale industrial evaluation, a numerical assessment was conducted to ascertain the feasibility of implementing sonic injection on Lonmin converters. The work included flow characterization at high injection pressures achieving sonic velocity at the tuyere exit. The 2D and 3D simulations of the three-phase system were carried out using the volume of fluid (VOF) and realizable k- e turbulence models to account for the multiphase and turbulence nature of the flow, respectively. These models were applied using the commercial CFD numerical code FLUENT.This paper discusses the key findings regard ing understanding of gas plume extension, velocity distribution, shear wall stress analysis, and phase distribution characteristics in the system. Plant trials are also discussed with reference to the commercial aspects of a fullscale implementation of sonic injection in the smelter."

Jan 1, 2014

By G. Asbjörnsson, E. Hulthén, P. Papadopoulou, C. M. Evertsson

Crushing plant managers need to assess, manage, and communicate the environmental impact induced by their crushing plant operations as a step towards the sustainable development of the company. However, performing reliable environmental impact calculations of crushing plants can be challenging when the availability of operational and emission data is low, and when the company’s environmental expertise is not adapted and connected to plant operations (or does not currently exist). To address these challenges, this paper proposes a practical approach where the lifecycle assessment methodology (LCA) is combined with process simulations in a web-based tool. To describe what functionality such a tool should have to be incorporated into a company’s workflow, the system that surrounds a crushing plant is analysed. Further, a case study with a three-stage crushing plant is introduced to showcase how the simulated power draw results produced with the beta version of the tool can be compared to measured sensor data from the crushing plant for one operational day. The results indicate that the simulation tool can provide an adequate estimation of the specific energy for the different material fractions and give an overview of the environmental impact of the process caused by electricity and explosives consumption. Plant managers and operators can use this tool to calculate the environmental impacts of their plant and simulate how different operational strategies influence them. Keywords: LCA, environmental impact, coarse comminution, crushing plant

Jan 1, 2020

By C. Liu, F. Ye

"To extend the variety of lump ores that are used in the COREX shaft furnace and to optimize iron ore blending, the original evaluation method for iron ores that was proposed by Voestalpine AG has been improved. Physicochemical and metallurgical properties of iron ores, including Sishen lump ore and CVRD pellets, which are currently used in the COREX process, and three other lump ores, were assessed and compared. Ore matching principles were proposed and five optimized iron ore blending schemes designed and verified by laboratory experiments to prove the effectiveness of the improved evaluation method. The replacement of Sishen lump ore by the alternative L2 and L3 lump ores without varying the proportion of CVRD pellets could improve the degree of reduction and rate of metallization, and decrease the bonding index. Based on the results of laboratory test work and industrial- trials, an ore blending scheme of 60% CVRD, 20% L2, and 20% L3 is recommended for use in the COREX process. IntroductionIn recent years, problems such as environmental pollution and a shortage of coke and coal resources for blast-furnace ironmaking have become increasingly apparent. Based on sustainable developments in the iron- and steelmaking industries, the environmentally friendly COREX smelting-reduction process with low energy consumption was developed and introduced (Zhou and Du, 2013; Song, Lv, and Yin, 2015; Xu et al., 2016; Kurunov, 2010). The evaluation system for lump ore that was proposed by Voestalpine AG recommends that only Sishen lump ore from South Africa be used in the COREX process, because of the stringent physicochemical and metallurgical property requirements. This situation significantly hampers improvements to the technical and economic aspects of the COREX ironmaking process, especially in China (Eberle, Siuka, and Bohm, 2006). No theoretical or technical basis has been provided for the evaluation system, and the assessment approach for iron ores also presents problems that need to be discussed and resolved.The COREX process consists of two reactors: the prereduction shaft furnace and the melting gasifier as shown in Figure 1 (Wu et al., 2017). Pellets and lump ores which are charged to the prereduction shaft should have a good reducibility and metallization with a low degradation index (Li et al., 2016; Wu et al., 2011; Kumar et al., 2009; Kang, Gupta, and Sahajwalla, 2007). The properties and microstructure of the iron ore pellets which are required to achieve a high productivity and a lower fuel rate in the COREX process have been investigated (Umadevi et al., 2011). Some efforts have also been made to investigate the behaviour of lump ores in the COREX shaft furnace, including the disintegration characteristics and the reduction degradation (Umadevi et al., 2011; Zhou et al., 2015; Xu et al., 2013; Li, Feng, and Zou, 2013; Hou et al., 2014). However, few studies have focused on the optimization of ore blending for partial or total substitution of the expensive Sishen lump ore by other, cheaper lump ores to reduce the production cost. The technology for the utilization of blended lump ores in the COREX process is still in its early development stages (Zhou et al., 2017; You et al., 2017)."

May 1, 2019

By N. du Preez, J. Christie, F. Crundwell

Precipitation is a key process in the recovery of copper and cobalt. While there is a wealth of experience in operating precipitation steps, improving their performance remains challenging. Chemically, the reaction might be controlled by reaction kinetics, be limited by oxygen mass transfer, or be at equilibrium. In this paper, we examine these different operating regimes and demonstrate how they can be identified from plant operating data, process modelling, and pilot plant test work

Jan 1, 2023

By A. C. Lawrence, K. F. Mauer

Human factors in stope productivity -a field experiment by K. F. MAUER, M.A. (Visitor), and A. C. LAWRENCE, B.Econ., D.Com. (Member) An experiment in which three human variables were manipulated in eight stopes was conducted in a gold mine over a period of roughly six months. The three variables, which each had two levels, concerned the degree of movement from gangs, the quality of the Bantu production supervisors, and the extent to which gangs were composed of a single ethnic group (Malawians). Time was included as a variable with three levels in the analysis of the findings. On the average, stable gangs produced 12 per cent more than gangs with a high percentage of transfers, gangs with better production supervisors were more successful by nearly 9 per cent than those with poorer production supervisors, and homogeneous gangs were more productive than heterogeneous ones by as much as 15 per cent. In addition, it was found that a number of the variables exercised a joint influence on stope productivity and that the effects of the variables were accentuated by the len gth of time they had been in operation. V

Jan 10, 1973

By S. Moolla, R. Lynch, S. Brijraj

A reliable method to locate microseismic evets is an important objective for routine mine seismic monitoring. We developed an algorithm that can automatically and reliably locate an event from a single uniaxial trace. Signals created by microseismic events are recorded as seismograms that consist of direct P- and S-waves as well as the waves reflected off the underground excavations. We take advantage of the extra complexity these reflections introduce as they make the signal more unique. In our investigation we cross-correlated unaltered synthetic seismograms against trial waveforms created from a linear combination of appropriate waveforms from a library of numerically calculated strain Green’s tensors. We use a single uniaxial synthetic seismogram to invert for the source location, six moment tensor components, and frequency. The resulting cost functions are constructed as maximal correlations at each node in the mine grid through the true source x-planes. This function is maximized by differential evolution to simultaneously yield the source parameters. Sensitivity tests such as shifting the mine plans and altering the background velocities of the media are investigated to test the robustness of the method. We contaminate the data with 40% white noise to test the resolution against simulated real recorded seismograms. The method is demonstrated using synthetic data calculated with a realistic underground 3D velocity model.

Jun 10, 2024

By P. Stefanek, N. Duda, B. Jachni, P. Stefaniak, B. Bursa

The Zelazny Most Tailings Storage Facility (TSF) is the largest reservoir of post–flotation tailings in Europe. The total amount of tailings from the mines in Lubin, Rudna, and Polkowice are stored each year at the disposal facility, which reaches approximately 30 million tons. It is crucial to accurately monitor and maintain such a huge storage facility, for the safety and economics of the entire region. In general, the monitoring network installed at the Zelazny Most TSF includes four groups of components: (a) geotechnical network (VW pore pressure transducers and inclinometers), (b) hydrological network (open piezometers, water level gauges, drainage discharge measurements, (c) geodetic survey network (e.g. surface and in-depth benchmarks, laser measurements, GPS measurements within GEOMOS network and (d) seismic network (e.g. accelerometer stations, cone penetration tests.) Apart from the above, chemical water analyses, tests of soil samples, monitoring of spigotting processes, and monitoring of relief wells’ discharge are also conducted. In total, approximately 2900 monitoring instruments are installed within the area of the Zelazny Most TSF. Such large amounts of data from the various information sources makes manual data analysis by the engineers almost impossible. In this paper we discuss a machine learning driven approach to improve the quality of the monitoring and maintenance of such facilities. We focus on the seismic cone penetration test (SCPT) data analysis. First, we carefully describe the collected data, its quality and availability. Then we discuss possible events that can occur in the TSF that need to be predicted using SCPT. Based on the information obtained in these two steps, the applicability of several machine learning methods is estimated. Some of them are then tested on available historical data. The algorithms described in this article will be further developed in the IlluMINEation project (H2020).

Sep 1, 2021

By C. S. Oteo, H. Suárez, P. de la Fuente

ABSTRACT: In the south of the Island of Gran Canaria (Spain) there appear layers of swelling clays inside volcanic formations of a fonolitic type, down to depths as low as 500 m, with thicknesses of 1 to 3 m. Two tunnels (each of length 1,500 m) have been built in these zones (ignimbrites and swelling clays), work on which started in the ‘70s. The construction has been influenced by phenomena of expansivity and decompression. Presented below are the problems that arose, the field and indoor studies conducted and the numerical optimisation of the lining. ZUSAMMENFASSUNG: Im Süden der Insel Gran Canaria (Spanien) kommen im Inneren vulkanischer Formationen phonolithischen Typs in Tiefen von bis zu 500 Metern 1 bis 3 Meter dicke Blähtonschichten vor. In diesem Gelände aus Schmelztuff und Blähton begann man zu Beginn der siebziger Jahre, zwei Tunnel von jeweils 1.500 Metern Länge anzulegen. Die Bauarbeiten standen unter dem Einfluss von Dehnungs- und Dekompressionserscheinungen. Der folgende Text enthält eine Darstellung der aufgetretenen Probleme, der durchgeführten Feld- und Laborstudien und der numerischen Optimierung der Tunnelauskleidung. RESUME: Dans le sud de l’Ille du Gran Canaria (Espagne) on a détecté des couches d’argile gonflante dans l’intérieur des formations de roches volcaniques fonolitiques, à la profondeur autom des 500 m, avec épaisseur de 1 à 3 m. On a perforé deux tunnels (de longueur 1.500 m chaque un) dans cettes zones (igniumbrités et argiles gonflantes), chantier qui comenza pendant les 70’. La construction on a influencé pour des phénomènes d’expansivité et de décompression. Dans cette communication on présente les problèmes presentes, les études de chantier et théoriques realicés et l’optimisation numérique développé pour dimensionner le revêtement.

Jan 1, 2003

By N. Lock

"Despite the pre-eminence of the Jwaneng Diamond Mine as the world’s richest diamond mine, the discovery story has long been clouded in mystery. This is the 45-year old untold story of the Jwaneng discovery and contemporaneous Bechuanaland/Botswana political and socioeconomic history. Diamond exploration by De Beers in Bechuanaland began in 1955, with the first true kimberlite discovery near Letlhakane in 1967, before Clifford’s Rule was applied and before the use of indicator mineral chemistry. Surface deflation soil sampling and bioturbation by termites was the foundation for exploration into the Kalahari. The 1962 reconnaissance programme south of Jwaneng had failed to make any discoveries. Improved sampling methods were applied to the Kalaharicovered areas in 1969 and positive results were received by year-end. The Whateley’s Wish percussion drill-hole in December 1972 was confirmed as Jwaneng 2424D/K2 with drill core in early 1973. Jumper drills were required to penetrate the Kalahari sand cover. Diamond resources were demonstrated despite multiple technical problems. IntroductionThe Jwaneng Diamond Mine is, by value, the world’s richest diamond mine. Harry Oppenheimer is quoted as saying that Jwaneng is ‘the most important primary deposit found anywhere in the world since the discovery at Kimberley more than a century ago.’ (Taylor III, 1982) The mine opened in 1982 after some nine years of evaluation and construction since discovery in February 1973. Debswana (2017) states that 2015 production was 7.87 Mt of ore from which 10.408 million carats were recovered at a grade of 132 carats per 100 t (cpht). Although the value is not reported, it was noted that Jwaneng contributes 60–70% of Debswana’s total revenue from all mines, including Orapa, Damtshaa, and Letlhakane (Debswana, 2017)."

Feb 1, 2019

By V. W. Lumadi, S. Nyasha

The mining industry has yet to fully accept and embrace the strategic role of technology and innovation in successful business planning and execution. In this study, we empirically determine the factors that influence acceptance of technology solutions in the mining industry in South Africa, assess critical success factors influencing adoption of advanced technology in the South African mining industry, and explore challenges faced by the mining industry in South Africa in adopting advanced technology in its operations. Thematic content analysis is employed in the data analysis. Results show that critical success factors to the adoption of mining technology include learning culture, knowledge sharing, high labour costs, and behaviour of other firms in the industry; commonly identified challenges include inadequate engagement with external stakeholders, uncertainties, the cyclical nature of the sector, and high risk related to the adoption of unproven technology and performance systems focused on volumetric production. The study encourages mining companies to implement usage of technology. This can be properly done through regular engagement with the Minerals Council South Africa.

Apr 14, 2024

By G. R. Drennan, N. J. Wagner, M. J. T. Sebola

The Soutpansberg Coalfield hosts South Africa's hard coking coal reserves. However, coals in this region are understudied compared to other coalfields in the country. This study characterizes the properties of fine-float fraction samples extracted from a wide diameter borehole core in the Makhado Project, Tshipise sub-basin, Soutpansberg coalfield. Conventional analyses were used to determine the coal quality, petrographic composition, mineralogy, geochemistry (including trace element and rare earth element composition), and free swelling index of samples from six coal horizons and three partings from the economic No.6 Seam. The coal samples are classified as medium rank bituminous C coals (0.88 %RoVmr, 0.92 %Rmax) and are highly vitrinitic in composition (97 vol% mineral matter free (mmf)). The samples show strong caking potential (FSI of 9). The total rare earth concentrations range between 570 and 3193 ppm in the ash samples. Preliminary analysis show all but two samples are promising sources of rare earth elements as the total concentrations exceeded the 1000 ppm cut-off grade. Further research is required to confirm these preliminary findings.

Aug 2, 2022