Search Documents

By Huanhuan SU, Jianqiang Zhang, Zhongyuan Liu, Junwei Ma

The high-sulfur bauxite in Henan Province was used as raw material. The grinding fineness, pH value and collector dosage on its desulfurization performance, and industrial flotation desulfurization process were studied. The best flotation desulfurization conditions were grinding fineness of 75%, pH of 8.5, and collector of 600 g/t. “One coarse, one cleaning and one sweep” closed-circuit flotation was established as the industrial flotation desulfurization process. After the closed circuit test, the sulfur content of aluminum concentrate with the yield of 93% was 0.23%, and the sulfur removal rate was 83.16%, and the sulfur content of tailings (sulfur concentrate) was 15.09%. Keywords：High-sulfur bauxite under coal mines, flotation, desulfurization

Jan 1, 2020

By C. B. Espag de Klerk, J. de Goede, M. Le Roux, Q. P. Campbell

"Excessive amounts of moisture in product coal can influence the efficiency of downstream utilization processes due to a decreased calorific value and handling problems. Stockpiles can be used to decrease the moisture content of coal by means of gravity drainage and evaporation. This paper is focused on the evaporation of moisture from a coal stockpile surface with the aim of investigating the effect of particle size on the rate of evaporation as well as the depth to which evaporation extends.It was observed that moisture initially evaporates at a higher rate from a stockpile consisting of fine particles (-6.7 mm) than from coarser particles (-13.2 mm +6.7 mm). This high rate of evaporation is restricted to the outer shell of the fine coal stockpile. However, for coarse coal, the porous nature increases the depth at which evaporation occurs. Evaporation of moisture was observed up to the fourth day of each experimental run, after which steady state was obtained. It was shown the water can evaporate from the surface into the body of the stockpile, depending on the coal particle size and void spacing. An experimental reclaim depth of 0.4 m was achieved after 4 days. IntroductionCoal stockpiles serve as surge capacity for downstream utilization processes and can also be used for moisture reduction by means of gravity drainage and evaporation. Excessive amounts of moisture in coal can cause handling problems and, most importantly, will decrease the calorific value, leading to inefficient combustion.Research has shown that evaporation by means of wind and solar action is considerably more effective than gravity drainage(Williams, D.J. 2006), but the effect is limited to a restricted depth from the exterior of the stockpile (Boyapati, E. and Oates, A. 1994; CSEM-UAE, 2010). The effectiveness of wind and solar action can be improved by orienting the stockpile perpendicular to the predominant wind direction, maximizing the surface area of the pile, and reclaiming the coal from the pile gradually in shallow cuts over a large area (Williams, D.J. 2006)."

Jan 1, 2016

By V. Sheikhzadeh, M. R. Sheikhzadeh, A. Haratian, M. Zare

High Pressure Grinding Roll (HPGR) as an efficient grinding technology plays a major role in mineral processing plants. Investigating the effects of this technology on different parts of mineral processing circuits reveals this technology’s capability. In this paper, HPGR grinding effects on an iron ore beneficiation circuit, in comparison with conventional crushing systems were studied. A representative feed sample was taken from an iron ore beneficiation plant, then crushed to minus 6 mm in a laboratory by two methods: HPGR and cone crusher, and finally a concentrate plant circuit was simulated. Plant simulation was performed by doing laboratory tests consisting of grinding, magnetic separation, flotation and filtration on HPGR and cone crusher products, respectively. According to comminution tests results, in particle sizes smaller than 6 mm, a cone crusher product is coarser than an HPGR product. Also, the Bond ball mill work index of the HPGR product was 10% less than the crusher product. Therefore, based on the Bond formula in applying HPGR, ball mill power consumption decreased by 12%. After ball milling to minus 100 microns, magnetic separation tests results showed that the recovery of the cone crusher circuit output was 90.8% and the product Fe grade was 66.4%. For the HPGR circuit these figures were 87.6% and 67.3%, respectively. Therefore, by using an HPGR, a higher Fe grade of the final concentrate was achieved. A flotation test was then performed on the magnetic separation concentrate, where the results showed that the crusher circuit recovery and the sulfur grade of the product were 96.5% and 0.192%, respectively; whereas the HPGR circuit recovery was 97.2% with a sulfur content of 0.185%. Findings revealed that flotation performance in the HPGR circuit was more efficient than the crusher circuit. Vacuum filtration tests on concentrate produced through the HPGR circuit resulted in a moisture content of 12% that was 2% higher than the crusher circuit’s concentrate in the same condition. Keywords: High pressure grinding roll, power consumption, magnetic separation, flotation, filtration

Jan 1, 2020

By J. K. Williams, M. P. Wells

"As part of the planning system at each division of Nchanga Consolidated Copper Mines, Limited, the Mine Planning Department is required to produce a detailed production schedule for each shaft.Because of the difficulties in producing a schedule which satisfies all the mining constraints, and because of the large clerical effort involved, the full range of possible schedules can never be considered.It has been found possible to produce a schedule using linear programming which satisfies the majority of the many varied mining constraints. Computer programs have been written to enable the mine planning department to use this mathematical system without assistance.The system has a large degree of flexibility to enable the planner to include conditions which cannot be incorporated readily in the linear program. This system permits the more efficient production and evaluation of schedules and reduces the amount of clerical effort."

Jan 1, 2014

By E. Emami, J. Valencia, J. Sattarvand

The knowledge of the final location of a drillhole is critical in obtaining the expected blasting results. This paper proposes a new methodology to control the drilling accuracy in open-pit mines using aerial images and machine learning. Specifically, it investigates how support vector machines (SVM) and convolutional neural networks (CNN) are useful for automatically detecting blastholes over drone images captured in blasting patterns. Several datasets were obtained from different mines in Nevada (USA) and were used to train and test models. We then processed those images to create orthomosaic and digital elevation representations of the patterns. Thousands of patches were then extracted and augmented to develop SVM and CNN models. The results demonstrate that machine learning is useful for drillhole detection and, in this way, to control the drilling accuracy and use the explosive energy more efficiently.

Sep 1, 2021

By Jürgen Antrekowitsch, Harald Osthof, Stefan Steinlechner

"In the case of feasibility assessments or feasibility studies, an important point of discussion is often how to calculate the capital (CAPEX) and operating expenditure (OPEX) of a plant. Generally, there is also the request to know how the CAPEX varies when the size of the plant is increased. Nowadays, many databases give an indication of specific equipment costs in relation to the production rate. These data are based on cost information from equipment suppliers and have to be continuously updated by the owner of the database. The approach presented here is a model which allows sizing of process equipment, for example a leach tank, based on process data in combination with the calculation of mechanical properties. Furthermore, it calculates the CAPEX based on construction material cost and adequate machining surcharges. Thus, a single cost model for a leach tank is adequate for both copper and other hydrometallurgical plants and stays valid with changing construction material prices. To summarize, the advantage of this model is the more versatile approach and thus the flexibility due to the inclusion of design aspects, process and mechanical engineering aspects and an updatable database. The database, which is in regard to material cost and is the basis for the cost estimation, is easily updatable from commonly accessible data. This model thus approaches the procedures of an engineering company when designing a plant and executing a cost calculation. INTRODUCTION Hydrometallurgy nowadays plays an important role in processing of primary and secondary resources. In copper metallurgy, hydrometallurgy accounts for roughly 20 % of worldwide primary production, especially in the case of oxide or low copper-containing ores. Zinc smelters changed their method of production from a pyrometallurgical-dominated concept decades ago to mainly hydrometallurgical routes today. Gold production processes using leaching, especially, have a long history without any development which would not be competitive if not based on hydrometallurgical concepts (Pawlek, 1983; Winnacker-Küchler, 2006)."

Jan 1, 2015

By Y. Yang, M. Zhang, X. Xia, S Shi, Z. Shen

A stepwise arrangement of flotation cells is the most common layout of a flotation circuit in the mineral processing industry. In such a design, slurry flows from upstream to downstream by means of gravity, and the middling products are returned to previous stages by pumps. This paper will introduce an alternative solution in which the forced-air and slurry-induced flotation cells are adopted so that all the flotation cells can be placed on the same horizontal platform and no pumps will be needed for middling product transferring. The technology of the forced-air and slurry-induced flotation cell will be described in detail, including unique features, the working principle and the related fundamental problems. The comparison of capital investment, operating cost and metallurgical performance will be made between the conventional stepwise arrangement and the samelevel arrangement technology based on industrial practice. Keywords: Forced-air and slurry-induced flotation cell, same-level arrangement, stepwise

Jan 1, 2020

By Y. Zhou, G. Chisakuta, P. Bwando, G. Mitshabu

A newly started copper hydrometallurgical plant was confronted with a manganese oxidation issue in electrowinning. This oxidation, in the absence of the amount of iron required to stabilise the electrolyte oxidation-reduction potential, is known to produce oxidants (MnO2, MnO4) that can cause accelerated degradation of the organic phase components in solvent extraction and corrosion of lead anodes in electrowinning. The overpotential required to build up the protection layer on new anodes causes an increased electrolyte potential that creates oxidized species in the electrowinning tankhouse, and these species come back to solventextraction plant with the recycled spent electrolyte. This paper discusses the impacts of manganese oxidants on the health of a plant organic phase. It also outlines the actions taken using iron scraps and sulfur dioxide to mitigate the problem that happened due to the lack of ferrous iron sulfate available on site, as recommended for better control.

Jan 1, 2023

By Y. G. Zhu, G. B. Zheng, X. X. Hu

Reverse flotation by cationic collectors is the classical method to reduce the silicon content in magnesite. But because of the low selectivity, there is a large loss of magnesite in the reverse flotation froth. To improve the efficiency of the collector, a novel collector named BK433 was developed in this paper. In order to determine the performance of the BK433 collector, a systematic experimental study was carried out with a high silicon magnesite in China. The suitable pH environment of slurry was confirmed, the depression effect of different depressants was investigated, and the flotation effect was compared with commonly used traditional collectors. The results show that the BK433 shows remarkable good selectivity and collection ability. After the 4 stages reverse flotation, the SiO2 content decreased from 3.76% to 0.25%, SiO2 impurity removal rate reached 94.69%. Meanwhile, the MgO content increased from 45.06% to 46.73%，the recovery of obtained concentrate (calculated by MgO) was 82.79%. Keywords: Magnesite, Desilicication, Reverse flotation, Collector

Jan 1, 2020

By W. Guiye, L. Chongjun, L. Huinan, Z. Yangge, H. Long

The current application of copper-molybdenum (Cu-Mo) separation inhibitors is often associated with large dosage, high toxicity, environmental pollution problems. In order to solve these problems, a light sensitive Cu-Mo separation inhibitor LS（light sensitive inhibitor，abbreviated to LS） was developed. In this paper, inhibitory performance, photodegradation rule, and acting mechanism of LS were studied. The subsequent test results showed that, compared with traditional inhibitors, LS has shown comparative advantages, with lower dosage and good inhibiting effect. A series of flotation tests with LS as inhibitor were conducted on a Cu-Mo concentrate. A locked-cycle test showed that a molybdenum concentrate containing Mo 49.88% and Cu 0.6%, with 93.23% molybdenum recovery and a copper concentrate containing Cu 29.92%, with 99.99% copper recovery can be obtained. The photodegradation performance of the reagent was investigated under 365 nm, 254 nm and sunlight irradiation. The degradation of the reagents could be completely achieved by irradiation of three wavelengths of light. However, with the different wavelength of irradiation light, the degradation rate is different, the time required to reach 50% degradation rate being 3 h (254nm), 4 h (solar light) and 6 h (365nm) respectively. The inhibition mechanism on chalcopyrite was studied. FTIR study showed that LS could be adsorbed on the surface of chalcopyrite by chemical adsorption, which could enhance the hydrophilicity of chalcopyrite. Ultraviolet adsorption tests indicated that the adsorption capacity of LS on chalcopyrite surface was greatly affected by pulp pH value, and the proper pH value was 5-9. Keywords: Copper-molybdenum separation, Inhibitor, Light-sensitive, Photodegradation, Mechanism.

Jan 1, 2020

Review Mining annual review June 1979. London, Mining Journal, 1979. 624 pp. Available as part of the subscription to the Mining Journal or at £12,50 per copy. This annual review is recognized internationally as the world leader in reporting on metals and minerals, and is eagerly awaited each year for its authoritative content, which is compiled by well-respected experts throughout the world.

Jan 1, 1979

By A. A. Bradley, P. J. D. Lloyd, A. J. Freemantle

Developments in centrifugal milling by A. A. BRADLEY,B.Sc. (Rhodes) (Visitor), A. J. FREEMANTLE, B.Sc. Hons. (Wits) (Visitor), and P. J. D. LLOYD, B.Sc. (Chem. Eng.), Ph.D. (Cape) (Fellow) The theoretical and experimental results of a study of centrifugalmills are reviewed. Means for the scaling up of such mills are suggested, and tests on a prototype mill are described. Despite the high lining wear in the centrifugal machine, which reduces its productive availability, its other advantages suggest that there is merit in pursuing its further development.

Jan 6, 1974

By M. J. Nicol, R. P. Colborn

An investigation into the kinetics and mechanism of the oxidation of iron (11) by oxygen in aqueous chloride solutions By R. P. COLBORN Pr. Eng., Ph.D. (Natal) and M. J. NICOLt B.Sc. Hons., Ph.D. (Rand) A reaction mechanism for the oxidation of ferrous chloride by molecular oxygen is developed. and the appropriate constants are evaluated. The effect of a number of cations and anions on the rate of oxidation has been tested.

By B. J. Madden

The formula developed by Salamon and Munro in 1967 has been used for the past 22 years in the design of bord-and-pillar workings in South African collieries. This paper re-assesses the formula In the light of Its past performance and examines the effect of mining method on coal-pillar strength. An account is given of the extension of the formula so that it can be applied beyond the empirical range for which it was derived, and the advantages of the extended formula (the squat-pillar formula) are described.

Jan 1, 1991

By C Smit

SYNOPSIS A prototype collimated radiometric face scanner was tested in the Harmony Gold Mine. The results obtained during the pilot study indicate that in situ radiometric uranium assays are statistically indistinguishable from those obtained conventionally from channel chip samples. In addition, the study demonstrated that reasonably reliable gold estimates can be deduced from the radiometric measurements, by use of the ratio of gold to uranium within a mine. The instrumentation, calibration procedures, and background determination are described briefly.

Jan 1, 1985

By J. H. Venter

The accuracy of estimation from samples of ore in bulk By J. H. Venter Published in the Journal April 1972. ERRATA: Equation (1) should read... Equation (3) should read .... line following "Duscussion" Delete" .... Insert... above "References" "Discussion". Replace .... tenth DISCUSSION M. DA VID Professor Venter has proposed a formula to compute the variance of the estimated grade of a lot of broken ore, and interesting comments on the relevance of the formula and suggestions for developments are made by P. R. Janisch.

Jan 4, 1972

By E. Tabosa, S. Vianna, K. Duffy, W. Valery, B. Andrade, L. Pyle, P. Holtham

Pneumatic flotation cells are high-intensity flotation machines with rapid kinetics, resulting in short residence times. Examples include the Jameson, PneuFlot and ImhoFlot cells. These cells do not use impeller-like mechanical cells. Rather, the air and pulp are mixed in a continuous stream of high fluid velocity through a downcomer or venturi to disperse the air into fine (approximately 0.5 mm) bubbles and maintain particle suspension. Froth wash water is often used to enhance concentrate grade, minimising recovery by entrainment. With the growing application of these types of cells, not only in cleaner stages (their traditional use) but also in pre-flotation and scalping duties, there is a need to predict their performance more accurately for circuit design and optimisation. No widely accepted model for pneumatic flotation cells is available and their metallurgical performance is often scaled up from laboratory and/or pilot plant testing by assuming fixed values for metal recovery, concentrate grade and concentrate percent solids. This paper describes a new approach to simulate pneumatic flotation cell performance and presents case studies demonstrating its applicability. Keywords: Pneumatic flotation, flotation modelling, flotation circuit design, flotation circuit optimisation, Jameson cell

Jan 1, 2020

By L. D. Robbins, M. L. Murphy, A. C. Campbell, L. Murphy

This paper reports on what appears to be the first discovery of prehistoric mica-schist mining in southern 4frica. The mine concerned was found in a location very rich in rock art that is one of the most important archaeological sites in the Kalahari. The authors conclude that the oval pieces of mica schist that were found at the mine site were used by Khoisan peoples to scrape fatty tissue from hides that were to be cured. Radiocarbon datings seem to indicate that such ovals were used for at least 20 000 years.

Jan 1, 1994

By H. A. D. Kirsten

SYNOPSIS This paper describes simple calculations to evaluate the stability of hangingwall and footwall strata at the work¬ing face and in backfilled areas. It shows that the benefits of support provided by backfill can best be realized when the fill is placed as close to the face as possible. The main beneficial effects of fill are that it reduces the stope span, at the same time providing a damping effect on vibrations, and prevents the fall-out of blocks in filled areas, thus maintaining the competence of the strata.

Jan 1, 1988

By D. Gerhart, J. Hung, J. Hackwood, A. Pix

A computer-based, real-time mine management system has been installed in a number of underground operations. The system’s innovative software application is coupled with wireless data acquisition and database management to provide complete mine monitoring and control execution in closed-loop control fashion. The system is well suited to automatically assign equipment, acquire status, and reassign resources based on status; and to automate information handling. The system has provided mines with improved utilization of the equipment fleet and mining crews, and reduced workplace cycle time. This paper describes the deployment of systems at a number of underground mining operations and discusses future development of the system. Keywords: Computer-based: Real time: Utilization: Mining cycle control: Monitoring: Productivity

Sep 1, 2001