Search Documents

By A. Yañez, J. Yianatos, P. Vallejos, R. Grau

This paper presents an evaluation of the effect that the mineral feed characteristics have on the metallurgical performance in an industrial flotation circuit. Variables such as mineralogy, particle size, solid content and mineral grade were evaluated using a flotation simulator, which was previously developed and validated using industrial data from different concentrators. The metallurgical performance was evaluated not only from the point of view of recovery and concentrate grade, but also by analysing less common variables such as froth carrying rate, froth and collection recovery, water recovery and others. Then, new data from the industrial flotation circuit was used to complement this analysis and evaluate the simulator predictability by comparing simulated and measured data. The results allowed for the quantification of the significant effect that mineralogy and particle size have on recovery and/or concentrate grade. Therefore, the grinding stage and flotation cells design become important factors to avoid a significant loss in metallurgical performance when feed mineral characteristics change in an industrial operation. In this context, an evaluation of cells design and arrangement should be performed to compensate the loss in recovery and concentrate grade in order to find an optimal operating condition. Keywords: Flotation circuits, mineral feed, modelling, particle size, liberation, mineralogy

Jan 1, 2020

By G. E. Rencken, J. H. Potgieter, A. Narain, J. Smith

To conserve fresh water resources and comply with environmental regulations, DRDGOLD, a South African gold producer re-treating surface tailings, has transitioned to a fully closed water circulation system. Consequently, the accumulation of contaminants, as well as addition of reagents, has led to changes in water composition that have compromised leach performance and overall gold recovery. A two-sample t-test confirmed a significant difference in gold recoveries between the use of Rand Water, which was used as a benchmark, and untreated process water. Atomic absorption analysis of ERGO’s process water, confirmed the presence of iron, nickel, zinc, and manganese. A study of the effect of the identified contaminants on gold recovery showed that iron, nickel, and zinc have the largest negative effect on gold recovery, with iron and nickel being more detrimental than zinc. Sulphates were shown to have a possible passivation effect, which also influenced gold recoveries, although to a lesser extent than the heavy metals. Calcium, when present in excess, had a positive influence on gold recovery indicating the possible formation of a calcium aurocyanide complex. Lime softening successfully reduced the heavy metal and sulphate concentrations, and the gold recoveries obtained with the treated process water were similar to those as achieved with Rand Water.

Jul 1, 2021

By D. Borman

The location of underground positions in mines has usually fallen to their survey department's. Their usual tasks include: ? installation of a high-precision peg network like the National Survey grid as beacons ? offset measurements to the sidewalls, and sometimes hangingwall and footwalls, of development tunnels and excavations ? offsetting of stoping panels for the calculation of face ? advance and the square meterage of area removed. Other departments build their observations into the plans produced by the surveyors. If more precision is required, they ask the surveyors to `elevate' their points with a theodolite. Apart from the survey peg network and `elevations' these measurements are usually planer measurements suitable for producing plans, sections and projection sheets. When the only representation medium was a sheet of paper or transparency, this was perfectly suitable. However the development of CAD models of the workings has changed all this. Full 3D representation is not properly catered for in the tool sets in current use, and needless hours are spent converting analogue-type observations into digital form. The basic survey models need to be augmented by the observations of other disciplines that are also required to locate positions underground. These include: ? the need for geologists to plott their mapping and ? borehole logs into 3D space ? the need for samplers to position their sample points accurately because the geostatistical models are biased and inaccurate ? the need for stoping width recorders to position their thickness observations to prevent errant evaluation and bonuses ? the need for rock engineers to place their mappings into 3D to build true geotechnical models to manage geotechnical stresses ? the need for production officials to receive updated face ? positions during the month so that they can manage the ? production and utilize their resources properly. This paper covers a new method of positioning profiling points to a suitable degree of accuracy. I believe the method is sufficiently simple and cheap for all to use. Historical methods Platinum and gold orebodies, especially in South Africa, are generally narrow tabular deposits. This made them suitable for depicting on a 2D medium like paper. The determination of stoping or face widths was not a problem, as the ore is removed in a single stoping process. Such 2D representations could be easily positioned using tape offsetting between survey pegs or points tied in from survey pegs. Problems of dip were handled by using 'Stope Sheets' which chose a best fit projection for the whole area depicted or by using true dip section sheets for inclined tunnels. Rolling reef and potholes were the common areas of difficulty. Most mines now model their orebody and plan the extraction in computer graphics. This means that the representation of the current workings has to change to support this trend. It now becomes a truly 3D problem. Mining officials find it inconvenient to have their actual workings in single-line depictions while their orebody is depicted with top and bottom contacts and the planned tunnels in 3D shapes. Geological models which form the basis for the resource model and planning process are often out of date, as the updating process is slow. The geological mapping has to be plotted onto sections and plans. These are then digitized into graphics by a draughtsman and checked by the geologist. Only then does the interpretation and model update take place. Potential methods to create 3D 'Actuals' Global positioning systems (GPS) Surface mines have been blessed by the advent of GPS technology. These simple-to-operate pieces of equipment and compatible software make it possible for all types of mine employees to locate themselves, and therefore to locate their observations. GPS are often inexpensive and give an acceptable degree of accuracy. Only in deep pits or close to the highwalls are observations hindered. Such technology cannot however, work underground. Ground penetrating radar (GPR) GPR is reported to be very useful for estimating the positions of potholes and faults. However it is still considered as providing an estimate, not a definite measurement. GPR is good for seeing into solid rock, not into open spaces. Inertia reading devices Experiments with inertia reading devices have been conducted on the mines. They were the forerunners of GPS for military guidance systems, and were even used for city navigation in the early 70s. They do however work best with heavy or fast-spinning gyros. Anglogold Ashanti's attempt to use them were discontinued in the mid-90s when the developers asked for an additional few million rand for a device that would weigh more than 12 kg and have a limited operational life.

Jan 1, 2006

By E. Kalhan, C. Kincal

One of the biggest problems in open pit mining is slope stability. The avoidance of slope stability problems depends on a comprehensive assessment of environmental and operational factors such as geology, climate, and mining activities. In the light of these considerations, slope geometries should be determined in accordance with engineering principles. In this research, the slope stability of rock slopes in a mine opened in a gneiss geological unit has been studied. Production activities were ceased in 2019 due to the slope movements in the eastern part of the quarry. In order to safely continue the production, field works were primarily carried out. To assess slope stability, detailed discontinuity surveys were carried out on bench faces. Subsequently, kinematic and numerical analyses were employed to identify geometries that are expected to maintain stability under the prevailing geological structures and environmental constraints. Engineering geological studies such as scanline measurements in steps and investigation of potential failure mechanisms by kinematic analysis technique were carried out. Small module reactor and Q-slope rock mass classification systems were used to evaluate slope stability. Based on these classification systems potential unstable rock slopes were identified and thematic maps were created using geographic information systems. The most suitable slope geometries are suggested for these slopes. In addition, the improvement methods suggested by the rock mass classification systems were proposed for these slopes.

Sep 1, 2025

By J. A. L. Napier

It has been established that significant time-dependent stope convergence may occur over time periods of hours and days in certain hard-rock gold and platinum mines. The source of this time-dependent behaviour appears to be associated with both pre-existing discontinuities and with mining-induced fractures that form near the stope face. These induced fractures may be associated with blasting processes and may also be formed in response to high stress concentrations in the unmined regions immediately ahead of the stope face. In shallower platinum mining operations, time-dependent behaviour is, however, observed to be much less marked unless some form of specific mining-induced fracturing occurs. One particular case of considerable interest is the time-dependent behaviour that is found to be associated with the formation and deployment of crush pillars. The purpose of the paper is to present a simple limit-equilibrium computational model of this behaviour that is sensitive to both the formation sequence and the size of planned crush pillars in a mine layout. This model provides a useful means to optimize the sizing of crush pillars, and at the same time may be used to identify potentially hazardous circumstances in which pillars may not crush in a stable manner.

Jan 1, 2012

By D. F. Malan, J. C. Esterhuyse

In this study we explore the use of a novel numerical modelling approach to study the effect of pillar reinforcement on pillar stability. Case studies in the literature indicate that tendons, strapping of the pillars, and shotcrete or thin spray-on liners are commonly used to reinforce pillars. No clear methodology exists to select the type of support or to design the capacity of the support required, however. This has led to ongoing collapses in some mines in spite of heavy support being used to reinforce unstable pillars. A limit equilibrium model with confinement on the edge of the pillar was used to simulate the interaction of the support with the failing pillar. The model correctly predicts that an increase in confinement will lead to a decrease in the extent of pillar failure. As the displacement discontinuity boundary element method allows for the efficient solution of largescale bord-and-pillar layouts, the effect of pillar confinement can now be studied on a mine-wide scale. Accurate calibration of the limit equilibrium model is, however, required before this method can be used for the design of effective pillar support.

May 3, 2023

By K. Woodward, Y. Potvin, B. McFadyen, M. Grenon

Open stoping has become a popular mining method in hard rock mines, not only due to the safety of the method as a non-entry approach, but also because of the high extraction rate and low costs. At mine sites, stope performance is evaluated by calculating stope overbreak using the stability chart. However, limitations of the stability chart regarding the precision of the predictions, nonconsideration of factors such as the influence of blasting, and the exclusion of underbreak have led to non-optimal designs. The capabilities of today's computers have increased the amount of data being collected and the power of models being built. This article presents a step towards a new stope design approach where stope overbreak and underbreak are measured and georeferenced using octrees at an approximately cubic metre resolution and predicted using multivariate statistical models (partial least square, linear discriminant analysis, and random forest). Results show that overbreak and underbreak location along the design surface and their magnitude are predicted with good precision using a random forest model. These predictions are used to build the expected geometry of the open stope. The resolution of the data and the use of multivariate analysis has enabled the prediction of variation in stope performance along the design surface, going well beyond the simple qualitative per stope face prediction provided by a traditional stability chart approach.

Jun 5, 2023

By S. W. Jacobsz, Y. Narainsamy

Several high-impact tailings dam failures around the world in recent years have placed a renewed focus on the stability of tailings dams and pointed to potential shortcomings in traditional drained design and safety evaluation procedures. A need to consider undrained shear strength in the design of tailings facilities has become apparent. However, there are specific requirements that need to be met before undrained shearing occurs. In South Africa, the last major failure was likely the Merriespruit disaster in 1994, which leads to the question of whether the conditions required for undrained shearing are readily applicable to South African tailings dams. This paper describes research at the University of Pretoria that has recently commenced to further investigate the conditions required for undrained failure to occur. The research includes laboratory and field testing to replicate these conditions in the laboratory and relate them to those found in an active tailings dam.

Jun 2, 2022

By N. F. Dawson

Recovery of a chromite concentrate from UG2 flotation tailings streams, of a grade suitable for further pyrometallurgical treatment for the production of ferrochrome, has certain specific challenges not only by virtue of the decoupled nature of the primary PGM recovery process and secondary gravity based chromite recovery circuits, but also because of intrinsic variations in the nature of the ore and its mineral composition. Variability in the ore, together with upstream process dynamics, creates a challenging environment in which to achieve optimal recovery of a gravity concentrate with accurate grade control. This paper examines certain inter-relational aspects between the ore gangue and chromite mineral types, the influence of the primary PGM extraction circuit and secondary chromite extraction activity as applied specifically to UG2 ore against a background of actual plant experiences and circuit configurations applied in order achieve a suitable quality of chromite concentrate.

Jan 1, 2010

By P. J. Le Roux

"Mining companies are under constant pressure to reduce their cost structures to sustain profitability. In mines using an open stoping mining method, dilution often has a significant effect on profitability. At Target mine in South Africa, dilution in some open stopes was found to exceed 10%, falls of ground being a major contributor to the problem. This dilution can reduce the recovered grade from 5.5 to 4.5 g/t, resulting in a potential loss of about R21 million per month based on a gold price of R240 000 per kilogram. In addition to the cost of dilution, the cost of damage to, or loss of, trackless equipment as a direct result of falls of ground in open stopes is significant. Other associated costs include transport, hoisting, secondary blasting, milling, and plant treatment of waste material. Stable open stopes are essential in order to reduce falls of ground. Back-analyses of stope instability at Target mine have indicated that conventional rock mass failure criteria are unsuitable for stope design. An alternative strain-based criterion has been developed, and has proved to be very successful, allowing the stability of open stopes to be calculated reliably. Since its implementation in 2010, dilution and equipment damage have decreased markedly, creating value for the mine. IntroductionMines that make use of an open stoping mining method aim to extract only the ore, leaving the waste behind. Many orebodies have well-defined boundaries between the ore and the waste rock. In such orebodies, the introduction of waste into the ore due to overbreak dilutes the grade. In massive disseminated orebodies, dilution is less problematic. Overblasting, falls of ground, or other causes may result in dilution. A study undertaken in Canada (Pakalnis et al., 1995) found that approximately 51% of all underground metal mines utilized open stoping mining methods and, from surveys conducted at these mines, open stoping operations experienced dilutions of up to 20%, and occasionally more. Dilution of this magnitude has a significant economic impact on any mining venture. Research carried out in Australia by Capes (2009) came to the same conclusion."

Jan 1, 2017

By B. X. Huang

Hydraulic fracturing technology is presented as a solution to improve permeability and thus solve the extraction problem of coal seam gas in low-permeability gas-bearing coal seams. Given an existing group of original cracks, the propagation of main hydraulic cracks and hydraulic wing cracks was simulated using realistic failure process analysis software. The process represents the structural transformation of hydraulic fracturing and permeability improvements caused by it. In addition, a field test for improving the permeability of gassy coal seams by hydraulic fracturing was also conducted. The propagation of the main cracks and wing cracks by hydraulic fracturing forms a network of original joint cracks, hydraulic wing cracks, and main hydraulic cracks, which improve the permeability of the coal seam. High-pressure water in the drill hole and in the main hydraulic cracks permeates the two flanks of the hole, forming the permeating water pressure. With an increase in drill water pressure and an extension of the main hydraulic cracks, the permeating water pressure on both sides of the main hydraulic cracks in the coal mass also increases. Hydraulic cracks tend to form connections through rock bridges. The extension of hydraulic wing cracks through connections in the rock bridges between the cracks transforms the rock mass to a fractured structure and improves its permeability. Hydraulic fracturing technology for improving permeability in underground conditions can increase the amount of gas drainage by a factor of 15. A stress relief area develops at a radial distance of 10-2.0 m from the hydraulic fracturing drill hole, while an area of rising stresses, called the pressurized area, develops a further 15 m away from the pressurized hole. Practice has proved the existence of the stress transfer phenomenon and the high stress area after fracturing. This kind of hydraulic fracturing technology is more effective in holes drilled from underground than in surface drill holes, with respect to costs and controllability, and is therefore the major trend in gas drainage development in coal mines.

Jan 1, 2012

By T. C. Huber

The southern African region has a high concentration of mineral resources and supplies much of the world?s platinum demand. As a result, the international community watches South Africa to understand the impact of supply on global markets. An analysis of supply certainty and risk plays a key role in the future of growing demand in various sectors. The southern African platinum industry experienced substantial growth in the early part of the 21st century, resulting in bullish forecasts for growth during the period of 2000?2006. However, southern African platinum producers saw a significant drop in production over the following three years as a result of many dynamic factors in operations and the global economy. Between 2006 and 2009 there was a million-ounce shortfall between forecast and actual production. This was raised as a concern at the Fourth International Platinum Conference in 2010 by Stephen Forrest during his keynote address, specifically regarding the lack of understanding in the market of the causes of this shortfall and any action that was being taken to address them. This paper reviews publicly available information in the media and corporate reports and communications for the period January 2006 to December 2009. In addition, several interviews were held with key stakeholders in the industry to provide further perspective. The paper then highlights the main reasons that are reported to have affected the loss in production over the period and discusses the possible implications of the information that the mining industry does and does not disclose regarding platinum supply.

Jan 1, 2012

By Y. Chen, D. He, J. H. Potgieter

The demand for rare earth elements (REE) is increasing rapidly owing to the emergence of new cleanenergy and defense-related technologies. China’s dominates the world production of REE. In this paper, we review the ore characteristics of four typical REE deposits in China and discuss the conventional beneficiation techniques, including gravity and magnetic separation, flotation, and hydrometallurgical processing of these ores. Some of the latest laboratory findings and industrial applications, as well as the development of novel reagents for REE processing in China are presented. The REE beneficiation technologies developed and employed in China could constitute a good case study for many other emerging projects being explored around the world.

Mar 2, 2022

By G. Dhakal, J. -I. Kodama, K. Neaupane, T. Yoneda

ABSTRACT Durability tests and evaluation of sub-zero temperature effects to some argillaceous clastic rocks were carried out. Welded tuff, limestone, sandstone and schist samples collected from different parts of Japan were tested and results are presented. Schist and dolomite from Ganesh Himal area along the higher Himalayas of Nepal were also tested, and the results are compared. The slaking tests were performed on all samples in pure water. The results reveal that the slaking index of schist from Japan is lower than that of schist from Nepal. Regarding carbonate rocks, the slaking index of limestone from Japan is higher than that of dolomite from Nepal. A tendency of decrease in slake durability with an increase in porosity is also observed. Freezing and thawing experiments conducted on welded tuff and schist reveal that crack initiates earlier but extends slower in schist than in welded tuff. It is also observed from the freeze-thaw experiment that the welded tuff deteriorates and wears faster than the schist. However, sandstone remains relatively intact for a long run of freeze-thaw cycles. Zusammenfassung Beständigkeitstests sowie die Bewertung der Auswirkungen von Minusgraden auf Tonschiefer Trümmergestein wurden durchgeführt. Dabei wurden geschweißter Tuff, Kalkstein, Sandstein und Schiefer aus verschiedenen Gebieten Japans sowie Schiefer und Dolomitgestein aus dem Ganesh Himal Gebiet, dem höheren Himalaya Nepals, untersucht und die Resultate verglichen. Für alle diese Gesteine wurden Slaking-Tests in reinem Wasser vorgenommen. Die Resultate zeigen, dass das Slaking von Schiefer aus Japan höher als das von Schiefer aus Nepal war, wohingegen bei kalkhaltigem Gestein das Slaking von Kalkstein aus Japan niedriger als das von Dolomitgestein aus Nepal ausfiel. Es wurde dabei auch eine Tendenz zur Löschbeständigkeitsverringerung bei gleichzeitig erhöhter Porosität beobachtet. Gefrier- und Tautests an geschweißtem Tuff und japanischem Schiefer zeigten, dass Risse in Schiefer schneller auftraten, aber sich langsamer ausweiteten als in geschweißtem Tuff. Bei Gefrier- und Tautests wurde ebenfalls beobachtet, dass geschweißter Tuff schneller verfällt und verschleißt als Schiefer. Sandstein hingegen blieb über lange Tau- und Gefrierzyklen intakt Résumé Des tests de solidités et l’évaluation de l’effet des températures en dessous de zéro sur les rocs argileux ont été effectués. Les rocs d’origine volcanique (cendre), les rocs calcaires, sableux et les schistes de différentes régions du Japon, ont été étudiés. Les schistes et les dolomites de la région de Ganesh Himal le long du haut Himalaya (Népal) ont été étudiés et comparés à ceux du Japon. Les tests de désintégration sur les rocs ont été effectués dans l’eau pure. Les résultats montrent que l’index de désintégration des schistes du Japon est inférieur aux schistes du Népal. En ce qui concerne les rocs carbonyles, l’index de désintégration des rocs calcaires du Japon est supérieur à ceux des dolomites du Népal. Une décroissance de la résistance à la durabilité est observée avec une plus grande porosité des rocs. Les tests de congélation-décongelation sur les schistes et les rocs d’origine volcanique (cendre) du Japon montrent une apparition précoce des fissures mais l’expansion des fissures est plus rapide dans les rocs volcaniques. Des tests similaires montrent que les rocs volcaniques (cendre) se désagrégent plus rapidement que les schistes. Cependant, les rocs sableux restent intacts après plusieurs cycles de congélation-décongélation.

Jan 1, 2003

A banquet, attended by 467 members and visitors, was held at the Wanderers Club, Johannesburg, at 8 p.m. on Friday, 21st March, 1969, to celebrate the 75th Anniversary of the founding of the Institute. Introduction of Dr Carel de Wet R. C. J. Goode (President) Dames en here: Ons het 'n aantal vooraanstaande gaste in ons midde vanaand en mnr Maxwell sal u later meer van hulle vertel. Dit is my aangename plig om u voor te stel aan sy Edele, die Minister van Mynwese, van Beplanning, en van Gesondheid, Dr de Wet en sy gade, mev de Wet. Sy Edele Dr de Wet het geen bekendstelling nodig nie-alhoewel hy ons minister vir slegs die afgelope twee jaar is, het hy reeds talle funksies van ons Mynbedryf bygewoon en het baie vriende gemaak onder ons. Hy het homself baie bemind onder ons gemaak toe hy Wes-Driefontein onlangs besoek het om hulle ondersteuning en aanmoediging aan te bied in hulle uur van nood. The Honourable Dr de Wet was born in the Free State. He is a grandson of that very famous general Christiaan de Wet, who caused so much pain to the British forces and for so many months so successfully eluded them in the Transvaal and Orange Free State. He was educated at both the Pretoria and Witwatersrand Universities. He first practised medicine at Boksburg and then moved to Vanderbijlpark, so you see he has an early association with gold mining on the Witwatersrand, and in moving to the Vereeniging-Vanderbijlpark district he became closely involved in our coal mining and metallurgical industries. South Africa's first steel was poured from a l0-ton open hearth furnace belonging to the Union Steel Corporation in Vereeniging in 1913. Dr de Wet has been mayor of Vanderbijlpark and for several years has been their member of parliament. More recently, the Honourable Dr de Wet has filled with great honour that most important office of Ambassador for the Republic of South Africa in London. At present he wears two hats, in that he is Minister of Planning and of Health, but more important is his cloak, that of Minister of Mines, which I trust offers him the greatest comfort. To fulfill these three arduous tasks must demand of him a terrific devotion to duty, and in doing this he carries on that loyal tradition of service to his fatherland so evident in his grandfather. Dames en here, dit is vir my 'n groot genoeë om Sy Edele Dr de Wette vra om 'n heildronk in te stel op die Instituut vir Mynwese en Metallurgie. Toast to the Institute of Mining and Metallurgy Dr the Honourable C. de Wet (Minister of Mines): Mr President, ladies and gentlemen, Mr President you have introduced me gracefully to this distinguished company and I am appreciative of your remarks. I am fully conscious of the responsibilities that devolve upon me as Minister of Mines in a country where mining makes so vital a contribution to economic progress and development and has, in fact, laid much of the foundation on which our present proud edifice is built. The achievements of the mining and metallurgical industry in its diversified activities arouse feelings equivalent to paternal pride, but let me speedily add that in considering any family relationship that may exist, the Minister of Mines should not be regarded in the role either of a fairy godmother or an indulgent father.

By J. Hadjigeorgiou, G. Knox

There is a considerable wealth of information on the behaviour of rockbolts under axial loading conditions both in situ and under controlled laboratory conditions. However, there is comparably less data on the behaviour of rockbolts in shear. Several authors have contributed to the understanding of the behaviour of conventional rockbolts’ performance under shear loading. Much of this data have been gathered through experimental programmes conducted on sections of the rockbolt. Considering the continuous coupling between the rockbolt and borehole interface, the approach is justified. Due to the design premise of energy-absorbing rockbolts with discrete couplings, full scale testing is required to quantify the behaviour of the rockbolts. This paper reviews published results obtained from two testing facilities, which are the SINTEF rockbolt pull test rig in Trondheim, Norway and the Epiroc Combinations Shear and Tensile test rig in Johannesburg, South Africa, both capable of conducting full scale testing of rockbolts. Based on this high-quality database it was possible to identify three distinct responses of rockbolts in shear. The behaviour under load is controlled by the presence or absence of an encapsulation medium (resin/cement grout), the reinforcement mechanism, and whether the rockbolt is continuously or discretely captured. As a reference the results are compared to the performance in shear of conventional grouted rockbolts.

Nov 24, 2025

By L. Ntlhakana, K. Khoza-Shangase, G. Nelson, I. Maposa

Occupational noise-induced hearing loss (ONIHL) is associated with various risk factors in South African mines. We investigated the association between standard threshold shifts (STSs) and exposure to noise and platinum mine dust (PMD), using demographic data, five years of annual audiometry screening results, and noise and dust exposure data. Miners’ age, sex, percentage hearing loss (PLH), and dust and noise exposure data were gathered, and a linear mixed effects regression model used to predict STS. Average occupational exposure levels to noise and dust were calculated from recorded measurements. A total of 12 692 records were analysed. Most miners were male (89.6%) and more than 50% were younger than 41 years. More than 70% were exposed to > 85 dBA noise and 58% were exposed to 1.5–2.99 mg/m3 PMD. Changes in hearing levels ranged from 8.3 dBHL at baseline (2014/2015) to 10 dBHL in 2016 (STS), with no changes thereafter. The model showed that the estimated effect on STS for males was 27% and 21% higher than for females, for the left and right ear, respectively The estimated effect of age, PLH, noise exposure and years of exposure on STS was < 10% for each variable. There was no statistically significant association between PMD and STS. The combined effects of age, sex, years of exposure to noise, and noise exposure levels, and strength of associations can be used to predict STS for this group of miners. Our findings may be used to measure the efficacy of the mine’s hearing conservation programme.

Aug 1, 2021

By O. S. Tinkler, K. C. Sole

Approximately 20% of current world copper cathode output is produced using a hydrometallurgical process route, generally referred to as the leach–solvent extraction–electrowinning flowsheet. Since its commercialization in the late 1960s, steady improvements in the performance and efficiency of the solvent-extraction reagents and equipment, combined with significant developments in leaching and electrowinning, have made an ever-widening range of ore types amenable to this technology. Following successful implementation on all major continents, a large proportion of growth in recent years derives from the re-emergence of copper solvent extraction in the Central African Copperbelt. This review provides a brief history of the development and evolution of copper solvent extractants and mixer-settler contactors, and the significance of the Copperbelt region in achieving commercialization and acceptance of the technology. The opportunities and challenges presented by the abundant high-grade oxide ores of the Copperbelt are contrasted with the processing of solutions derived from the low-grade mixed oxide–sulfide ore bodies that are prevalent in other geological regions. The current status of hydrometallurgical copper production in the African Copperbelt, within a global context, and a medium-term outlook for the technology are discussed.

Jul 5, 2023

By H. Brüggemann

The exploration of deposits generates geological data which are suitable for creating a preliminary tectonic and stratigraphic model. Linked with the topographical map and analysis data from exploration drillings, this information forms a numeric representation of the deposit. The following example demonstrates an expert system which connects chemical quality requirements and quarrying criteria, and develops a quarrying strategy based on the calculated model. Additional constraining factors like process technology, quarrying methods, landscape protection regulations, etc. are included. The goal is to guarantee a long-term, homogeneous material flow from the quarry at acceptable production costs - even in the case of an extraordinarily inhomogeneous deposit. In order to fulfil this requirement it is necessary to consider a large number of rules, criteria and instructions which can be structured as an expert system and programmed with LISP at a comparably low cost. The chosen strategy is not necessarily final, but can be changed any time by altering or varying the framework of conditions. The output consists of a block-working sequence which best satisfies the set requirements for appropriate points of quarry opening.

Jan 1, 1987

By W. Ferreira

Steel is produced in a basic oxygen furnace from hot metal obtained from a blast furnace. A sintered iron ore with good hightemperature properties (strength and permeability) should be used as feed to the blast furnace. The quality of this sintered ore depends on the reactivity of the iron ore used as feed to the sinter plant during the lime assimilation step in the sintering process. The penetration test is the standard method for evaluating the reactivity of iron ore with lime. It is, however, difficult to determine the exact depth of penetration from the standard test. A new test method is proposed that allows automatic evaluation of iron ores in terms of lime assimilation with increasing temperature. A comparison of the coefficients of variation for the new and standard methods for each ore type demonstrates that the results of the new test are more reproducible and more precise than those of the standard method. The test is also less time-consuming and easier to implement.

Jan 1, 2014