Search Documents

By S. Ata, Y. Pan, S. Gautam, G. Bournival

Bubbles play a vital role in flotation, and their properties directly affect the flotation performance. Xanthates are one of the major collectors used in sulphide mineral flotation. It is often believed that their main function is to render the desired mineral surface hydrophobic, which is essential for the mineral particles to attach to air bubbles. This paper takes a systematic approach to assess the influence of potassium amyl xanthate (PAX) at the air–liquid phase and its interaction with the frother in the concentration of range 10–5×104 ppm. Bubble size was measured in a laboratory flotation cell using a photographic technique and the stability of bubbles was quantified in terms of coalescence time -, the time required for a bubble pair produced at adjacent capillaries to merge into a single bubble. Bubble size reduction of up to 26% was observed with increasing PAX concentration in the cell. The bubble coalescence experiments using PAX only showed that the bubbles coalesced quickly at lower concentrations (10–50 ppm), but they stayed extremely stable at higher concentrations (1×102–1×104 ppm). Further experiments were carried out where the concentration of PAX was fixed at 1 ppm and 4- Methyl-2-pentanol (MIBC) concentration was varied. The synergetic action of PAX and MIBC significantly improved the stability of bubbles in the mixed system, and is even compatible with a stronger frother. The results strongly suggest that the role of PAX at the air–liquid phase should be considered in the practice of sulphide flotation. Keywords: Bubble size, bubble coalescence, PAX, bubble stability

Jan 1, 2020

By L. Uotinen, M. Rinne, R. Mishra

Underground mining gives rise to geotechnical hazards. A formal geotechnical risk assessment can help to forecast and mitigate these hazards. Frequentist probability methods can be used when the hazard does not have many variables and a lot of data is available. However, often there is not enough data for probability distributions, such as in the case of new projects. The risk assessment is often subjective and qualitative, based on expert judgement. The purpose of this research is to present the use of Bayesian networks (BNs) as an alternative to existing risk assessment methods in underground mines by combining expert knowledge with data as it becomes available. Roof fall frequency forecasting using parameter learning is demonstrated with 1141 sets of roof fall data across 12 coal mines in the USA. The prediction is nearly identical for individual mines, but when multiple mines are evaluated it is difficult to find a single best fit distribution for annual roof fall frequency. The BN approach with TNormal distribution was twice as likely to fit the observed data compared to the Poisson distribution assumed in the past. A hybrid approach using BN combining multiple probability distribution curves from historical data to predict annual roof fall is proposed. The BN models can account for variability for multiple parameters without increasing the complexity of the calculation. BNs can work with varying amounts of data, which makes them a good tool for real-time risk assessment in mines.

Jun 1, 2021

By L. Bam, R. Machaka, S. Chikosha, N. S. Muchavi

"Parts manufactured through power metallurgy (PM) typically contain pores that can be detrimental to the final mechanical properties. This paper explores the merits of 3D X-ray computed tomography over traditional microscopy for the characterization of the evolution of porosity in metal injection moulding (MIM) and direct powder rolling (DPR) products. 17-4 PH stainless steel (as-moulded, as-debound and sintered) dog-bone samples produced via MIM and Ti-HDH strips (as-rolled and sintered) produced via DPR and were analysed for porosity. 3D microfocus X-ray tomography (XCT) analysis on specimens from both processes revealed spatial variations in densities and the existence of characteristic moulding and roll compaction defects in agreement with traditional microscopic microstructural analysis. It was concluded that micro-focus XCT scanning can be used to study MIM and DPR parts for the characterization of the amount, position and distribution of porosity and other defects. However, the majority of the sub-micron sized pores could not be clearly resolved even at the highest possible instrument resolution. Higher-resolution scans such as nano-focus XCT could be utilized in order to fully study the porosity in MIM and DPR parts. IntroductionMetal injection moulding (MIM) is a novel process, which combines the advantages of powder metallurgy (PM) and plastic injection moulding. MIM has found widespread applications in the cost-effective production of high-sintered density small parts with complicated shapes and mechanical properties equivalent to those of wrought materials (German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013). There are four basic processing steps involved in MIM, namely; feedstock preparation, injection moulding, debinding and sintering. These steps are discussed in greater detail elsewhere (Machaka, Seerane and Chikwanda, 2014; German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013).Feedstock preparation involves mixing metal powder with a carefully selected composition of polymeric binder materials at a specific temperature. The feedstock is then granulated and injected into a predefined mould die with the desired shape. The part produced during the moulding step is referred to as a ‘green’ component. The green component typically contains no porosity since the spaces between adjacent powder particles are readily filled with the binder materials (German and Bose, 1977; Li, Li and Khalil, 2007). Debinding is the systemic removal of the binder components by chemical, catalytic, or/and thermal means while maintaining the shape of the component. The part produced after the debinding step is referred to as a ‘brown’ component. Debinding is known to be the source of porosity in brown components (Ji et al., 2001; Tsai and Cen, 1995). Finally, the brown debound part is sintered to full or nearfull density (Sotomayor, Varez and Levenfeld, 2010). The sintering step and associated densification closes up the majority of the pores. Sintered MIM parts are typically sintered to high density (95–99%) and retain an irreducible amount of residual porosity (Barriere, Liu and Gelin, 2003; German, 1990)."

Jan 1, 2016

By M. Pötsch, W. Schubert, A. Goricki

Geological and geotechnical data are essential for the design of tunnels. To determine the rock mass behavior and the support of a planned tunnel excavation a consistent method for rock mass characterization and excavation and support determination has been developed. Probabilistic data processing with analytical methods is used for the quantification of the procedure and allows an evaluation of the applicability and the technical risk of different excavation and support methods. The sensitivity of the procedure on selected input parameters is highlighted in a parametric study. Finally an application of the procedure illustrates the use of the described method of probabilistic excavation and support determination for tunnels. Des données géologiques et géotechniques sont décisives pour la planification d’un tunnel. Pour la détermination du comportement des strates, le choix du soutènement et de la méthode de progression une description compréhensible de la montagne a été développée. À l'aide d'un traitement de données probabiliste, la procédure proposée est transposée quantitative sur une base de méthodes analytiques. De cette manière l'évaluation des méthodes de construction et la détermination du risque technique deviennent possibles. La sensitivité de la procédure de différents paramètres d'entrée est représentée dans une étude de paramètre. Pour finir, l'application de la procédure décrite est montrée à l’aide d'un cas pratique. Geologische und geotechnische Daten sind entscheidend für die Planung von Tunnels. Für die Ermittlung des Gebirgsverhaltens und der Festlegung von Ausbruch und Stützung wurde ein nachvollziehbarer Ablauf der Gebirgsbeschreibung entwickelt. Mit Hilfe von probabilistischer Datenverarbeitung auf Grundlage analytischer Methoden wird die vorgeschlagene Prozedur quantiativ umgesetzt. Dadurch werden die Bewertung von Baumethoden und die Ermittlung des technischen Risikos ermöglicht. Die Sensitivität des Verfahrens von einzelnen Eingangsparametern wird in einer Parameterstudie dargestellt. Abschließend wird anhand eines Beispiels die Anwendung des beschriebenen Verfahrens gezeigt.

Jan 1, 2003

Report M294 A mineralogical investigation of potential gold-sorbing minerals and shales, by c.T. Logan. Dec. 1986. 12 pp. Computer software The Fifth IFAC/IFIP Symposium on Software for Computer Control (SOCOCO 88) is to be held in J ohannesburg from 26th to 28th April, 1988. Tunneling 88 The Institution of Mining and Metalurgy, with the cooperation of the British Tunneling Society, the Institution of Mining Engineers, and the Transport and Road Research Laboratory, Department of Transport, is pleased to announce the fifth international symposium, Tunneling 88, which wil be held in London, England, from 18th to 21st April, 1988. Ion-exchange processes ION-EX '87, an international conference and industrial exhibition on the industrial, analytical, and preparative applications of ion chromatography and ionexchange processes, wil be held in Wrexham (North Wales) from 13th to 16th April, 1987.

Jan 1, 1987

By T. Fraszczak, U. A. Peuker, T. Mütze, O. Ortlepp

Dolomite is a calcium carbonate sedimentary rock that can be found all over the world. In its calcined form it is employed for water treatment or as an additive in iron production. Calcined dolomite is produced at the Wünschendorfer Dolomitwerk GmbH in shaft furnaces (kilns). Because of an expansion of the mined deposit, significantly higher extraction costs were expected. Therefore, the existing upgrading processes for the kiln stone fraction had to be adapted and improved. This paper presents a process optimisation which allows for an increase of the yield of calcined dolomite by 10 % due to a redesign of the crusher circuit and by an additional 5 % due to a comprehensive characterisation of the kiln stone fraction itself. Here the interdependency between the pressure drop in the furnace during calcination and the size distribution of furnace stones was used to increase the amount of fine size fractions in the furnace feed without deterioration of the calcination process. Keywords: Dolomite, crushing circuits, kiln stone production, flowability, calcination

Jan 1, 2020

By Y. Qin, X. Fu, T. Qi, H. Tang

"The FASTMELT ® process was developed as an alternative to blast furnace ironmaking; in this process, high-quality molten iron is produced using direct reduction followed by high-temperature slag/metal separation. In this study, iron recovery and phosphorus removal from oolitic highphosphorus haematite using the FASTMELT® process was investigated. The performance of two reducing agents, coal and wood char, was compared. Direct reduction experiments indicated that with optimized reductant addition, the ore-char and ore-coal briquettes attained metallization values of 82% and 78%, respectively, and residual carbon contents of 0.24 and 2.35%, respectively. The slag/metal separation experiments revealed that molten iron containing 0.41% phosphorus and 0.021% silicon (by mass) was produced from optimally reduced ore-char briquettes, and molten iron containing 0.78% phosphorus and 0.91% silicon from optimally reduced ore–coal briquettes. The study indicates that carbonaceous materials with high CO2 reactivity are suitable for use in the FASTMELT ® process for phosphorus removal and iron recovery from oolitic high-phosphorus haematite. IntroductionIn China, the general depletion of iron-rich mineral reserves has led to many efforts to exploit low-grade and refractory ironcontaining resources for ironmaking (Liu et al., 2014). The efficient utilization of the highphosphorus oolitic haematite resources in central China has received considerable attention. The available resources of this material total approximately 3.0 billion tons. The oolitic units in the ore exhibit an onionlike structure with phosphorus-containing gangue layers of 2–10 µm thickness. The best concentrate produced from these resources contains approximately 50% iron (Fe) and 0.8–1.2% phosphorus (P) (by mass) (Ai, Yu, and Wei, 2009; Song et al., 2013; Wu, Wen, and Cen, 2011). Further removal of phosphorus from these ores using conventional beneficiation methods is not possible."

Jan 1, 2017

NIM reports Report No. 1615 Fluorspar pellets. A survey of the world market and an assessment of future South African production. Report No. 1621 Correction for matrix effects in the analysis of solutions by X-ray-fiuorescence spectrometry. Notices Questionnaire on Technicians The Department of National Education's committee of enquiry into the education, training, utilization, and status of engineering technicians in the Republic of South Africa was established as a result of Resolution 6.3 taken at the Sixth Conference on Engineering Education: The Education and Training of Engineering Technicians. Vraelys oor Tegnici Die Departement van Nasionale Opvoeding se komitee wat ondersoek instel na die opleiding, gebruik en status van ingenieurstegnici in die Republiek van Suid-Afrika is gestig as gevolg van Besluit 6.3 wat geneem is tydens die Sesde Konferensie oor Ingenieursopleiding: Die Opleiding van Ingenieurstegnici. Competition for Student Members of the South African Institute of Mining and Metallurgy Each year the Institute offers a prize (or prizes should the entries warrant it) of up to R100 for the best paper or dissertation on a topic appropriate to the interests of the Institute. The competition is open to all Student Members of the Institute.

Jan 8, 1974

By J. Sikamo, A. Mwanza, C. Mweemba

"The Zambian copper mining industry as we know it today had its genesis in the 1920s. Consistent private sector-driven investment in the industry over a period of over 50 years in exploration, mine development and operation, development of minerals processing facilities, building of infrastructure for pyrometallurgical and hydrometallurgical processing, with attendant support facilities, including building of whole new towns, resulted in copper production rising to a peak of 769 000 t in 1969, providingover 62 000 direct jobs. The industry was nationalized in 1973 and remained in government hands for just over 24 years. During this period, the industry experienced a serious decline in production levels, reaching the lowest level in the year 2000 when production was 250 000 t. An average of just under 2000 jobs were lost every year in the 24-year period, reaching just over 22 000 direct jobs in 2000.Following the return of Zambian politics to pluralism and liberalized economic policies, the government decided to privatize the mining industry. The process started in 1996 and by the year 2000 all the mining assets had been privatized. The new investors embarked on serious investment to upgrade the assets and to develop greenfield mining projects. Fourteen years later and after more than US$12 billion investment, production levels increased year-on-year to a peak of 763 000 t in 2013 with direct jobs reaching 90 000.This paper discusses the impact of the mining industry in Zambia on the economy in areas such as employment, support for other industries, direct contribution to the national gross domestic product (GDP), foreign exchange earnings, and social amenities. The paper also focuses on the performance of the mines during these periods vis-à-vis mineral availability, mineral grades and complexity, new technologies, and human capital. This is looked at particularly in the light of current challenges the industry is facing. Suggestions are proposed on how the industry can be nurtured to continue being a major driver for the Zambian economy and a major player in the international copper mining business."

Jan 1, 2016

By R. Tabanrad

This article examines the stability analysis of intake tunnels of Karun III dam & power plant. The tunnels have been excavated with a 3-dimensional and fairly complicated geometry in Pabdeh weak formation rocks at Zagros region. Due to the particular excavation geometry and inapplicability of plane-strain status, the stability of these excavations has been analyzed using both the 3D elastic software Examine 3D and the 2D non-elastic software UDEC simultaneously. The geomechanical parameters have been estimated by back analyzing the measured displacements from instruments, which were installed in the tunnels, and the parameters have been used in non-elastic numerical model. The results of the analysis show that the strains occurred in surrounding rock mass are less than the allowable failure strain and that the tunnels are stable. In addition, considering the results of non-elastic 2D analysis, the areas with unstable potentiality were identified and after the instability occurred at the areas predicted by the model , it was stopped up to the allowable strain limit through installing additional support . Bei diesem Artikel handelt es sich um eine Analyse der Festigkeit der Eingangstunnel des Damms und Elektrizitätswerks “Karoon III”.Die Tunnel haben drei Dimensionen und eine sehr schwierige Form und sind in brüchigen Felsen in “Pabedeh ,in Zagrossgebirge”eingebohrt.Aufgrund besonderer Form der Bohrung wurde ihre Festigkeit durch elastische dreidimensionale Soft-ware analysiert,die gleichzeitig die drei-und zweidimensionale unelastische Soft-ware UDEC benutzt hat.Die geometrische Parameter sind mit Ausnützung der Analyse berechneter eingesetzter Versorgungen,die in Tunnel aufgebaut sind,bewertet.Und diese Parameter sind in Zahlen-Analyse benutzt.Die Ergebnisse dieser Analyse zeigen,dass die Drücke an Felsen weniger als problematischer Grad der Drücke sind und die Tunnel fest sind.Ausserdem wurde mit einem Einblick auf die Ergebnisse der unelastischen zweidimensionale Analyse die eventuellen unfesten Teile bestimmt.Nach entstandener Unfestigkeit an diesen Teilen wurde die problematischeDrücke für Aufbau mehrere Anlagen gestoppt. Cet article examine l'analyse de la stabilité de tunnels de la prise de Karoun barrage III et centrale électrique. Les tunnels ont été excavés avec une 3 dimensionnel et compliqué géométrie dans Pabedeh que la formation faible balance à région Zagros équitablement. Dû à la géométrie de l'excavation particulière et inapplicabilite de statut de tension plane, la stabilité de ces excavations a été analysée en utilisant les deux le 3D logiciel élastique Examen 3D et le 2D logiciel non - élastique UDEC simultanément. Les paramètres du geomechanical ont été estimés en analysant le déplacement mesuré d'instruments qui ont été installés dans les tunnels et les paramètres en arrière a été utilisé dans les modèles numériques non - élastique. Les résultats de l'analyse montrent que les tensions se sont produites dans masse du roc environnante est plus petit que la tension de l'échec admissible et que les tunnels sont stables. De plus, les régions avec potentialité instable ont été identifiées étant donné les résultats de 2D analyse non - élastique, et après que l'instabilité se soit produite aux régions prédites par le modèle, il a été arrêté jusqu'à la limite de la tension admissible à travers installer du support supplémentaire.

Jan 1, 2003

By S. Langea, H. Lieberwirth

Impact crushers are common machines in comminution plants. Their high size-reduction ratio and relatively simple design, make them a preferred tool even when subjected to harsh wear, and producing a large quantity of fines in some applications. Until now the alignment of the operational parameters was an operator’s responsibility. Due to the random process characteristic this is mostly done based on empirical values and sensor data, such as power consumption. This paper describes a new approach for online process monitoring of the horizontal-shaft-impact crusher. The application of robust, low-cost acceleration sensors enables the permanent observation of the process characteristics. The operational and evaluation methods are determined on the basis of experiments. Subsequently the recorded measurements are analysed in regards of throughput, rotational speed and product particle size distribution. Occurring signal characteristics are described based on physical and technical principles. The measured data of the acceleration sensors at varying operation conditions provide insight in the course of process. The accurate utilisation yields the determination of the preferential process conditions providing the best balance between the pros and cons of an impact crusher. Both the experimental method and the data processing is discussed from a scientific perspective, displaying a completely new approach for the operation of impact crushers. Keywords: Impact crusher, acceleration sensors, data processing, particle size

Jan 1, 2020

By J. D. de V. Louw

Introduction Zircon is a natural occurring mineral and may exhibit natural low level radioactivity. It contains trace levels (90 to120 pCi/g and 110 to 115 pCi/g respectively or 3.3 to 4.4Bq/g and 4.1 to 4.3 Bq/g) of naturally occurring radioactive uranium and thorium. This mineral is often found in a suiteof minerals (rutile, ilmenite and monazite) Due to the overlap in physical properties of monazite (containing 4–7% thorium) with some of the zircon (slight magnetic susceptibility) it often contaminates the zircon, adding to the levels of thorium in the product. Hazards associated with the products from zircon and its processing is inhalation of respirable dust (generated by milling) containing radioactive uranium and thorium which may cause cancer of the lungs. Legislature regulates the transport, use, workplace environment exposure and storage of radioactive material. In America the general regulation for the unlicensed use of low levels of radioactive materials limits the concentration to 500 ppm (U plus Th). Europe (IAEA) specifies a limit of10 Bg/g (Bequerels per gram) on the parents for transport only which is a higher level of U+Th. Companies selling into these markets need to comply with these regulations and certification is therefore required, not only of the major constituents determining the price, but of the U and Th levels as well. Exceeding the limits for U and Th may result in material being returned to the country of origin. However, for the analyst the requirement is to analyse for these elements throughout the production process as well as the analysis of the ‘tails’ that is returned to the mine area. This requires a wide range of concentration to be analysed. Methods of analysis A wide variety of methods exist for the analysis of U and Th in a range of matrices. (Table I) All these methods have been used with varying degrees of success in terms of accuracy. Overall precision for the different techniques varies from 5 to 25% relative. Time to produce results from these methods vary from a few minutes to several days. The Production Chemist is expected to produce between5 and 10 analyses per hour for process control purposes. A suitable technique that fits this requirement is X-Ray Fluorescence. Both Wavelength Dispersive (WDXRF) and Energy Dispersive X-Ray (EDX) instruments are suitable. X-Ray analysis in general has a few major advantages over competitive techniques. •It is fairly simple to set up and interferences are known and easy to correct •It has multi-element analysis capabilities •Clean spectral lines for U and Th (in zircon specifically) •Uncomplicated and easy to measure background •Low detection limits (3 to 5 ppm) •A very high degree of precision •Sample preparation is uncomplicated and fast (pressed powders and fused beads). In Zircon (ZrSiO4) processed sands the matrix is constant(>99% ZrSiO4) and the background is thus essentially constant. A typical set up for the analysis of U and Th by WDXRFis given below: X-Ray Tube Tungsten (W) Target, 2.5 to 3kW operated at 50mA/50kV Crystal LiF200 (or LIF220 for higher resolution) Analytical Lines (2?)U La1,226.14Th La1,227.47 Detector Scintillation Counter Analysis time, depending on the concentration can vary from as little as 20 seconds up to 5 minutes. Standards As with any other comparative technique XRF analysis relies heavily on the quality of the standards used. Assuming proper set-up and operation of the instrumentation as well as consistent sample preparation, accuracy is determined by the quality of the initial calibration standards. A search for the available zircon certified reference materials (CRMs) shows that there are only a few CRMs

Jan 1, 2003

By Deur T. A. M. Saayman

Die sesde jaarlikse Ingenieursimposium is in September by YSKOR, Vanderbijlpark gehou. Rierdie simposium, wat deur Ingenieurs-in-Opleiding georganiseer word, bied aan die Ingenieurs-in-Opleiding die geleentheid om referate te lewer oor projekte wat gedurende hul drie jaar opleidingsperiode uitgevoer word. Continuing education courses The following courses are to be given in the near future in The Netherlands. Coal trade, transportation, and handling . The 4th Coal Trade, Transportation and Handling Conference and Exhibition, CoalTrans '86, will take place the Rai Congress Centre, Amsterdam, from 10th to 12th June, 1986.

Jan 1, 1986

By H. Sasao, Y. Obara, A. Hirata

In the upper part of the planned location of the portal of a highway tunnel, there was a steep rock cliff with several unstable rock blocks. It seemed that the risk of those rock blocks to fall was very high. The cut-out to stabilize the rock cliff was monitored with various measuring instruments to prevent the sudden fall of the rock blocks. This paper discusses the measurement of acoustic emission and interpretation of its result during excavation of the rock cliff. We calculated displacements by integrating the accelerogram twice in terms of time, and demonstrated that slight displacements can be calculated from the measured AEs. Dans la partie supérieure de l’emplacement prévu pour le portail d’un tunnel autoroutier, il y avait un escarpement rocheux raide avec plusieurs blocs rocheux instables. Le risque de chute de ces blocs semblait très élevé. Lors de la coupe pour stabiliser l’escarpement rocheux, le suivi a été effectué avec différents instruments de mesure pour éviter la chute brutale des blocs rocheux. Cette thèse présente les mesures d’émission acoustique (EA) et l’interprétation de leurs résultats pendant l’excavation de l’escarpement rocheux. Nous avons calculé des déplacements en intégrant l’accélérogramme deux fois par rapport au temps, et montré que de petits déplacements sont calculables à partir des EA mesurées. Im oberen Teil des geplanten Ortes des Stollenmundes eines Autobahntunnels gab es einen steilen Felsen mit mehreren instabilen Felsenblöcken. Die Gefahr schien sehr groß zu sein, dass diese Felsenblöcke einstürzen können. Beim Abbau um die Stabilisierung des Felsens wurde das Monitoring mit verschiedenen Messinstrumenten zusammengestellt, um den plötzlichen Verfall der Felsenblöcke zu verhindern. Das vorliegende Papier diskutiert die Akustische Emission und die Auslegung deren Ergebnisse während des Abbaus des Felsens. Wir berechneten die Verschiebungen durch zweimalige Integrierung der Accelerogrammen in Bezug auf die Zeit. Die dargestellten kleinen Verschiebungen können aus den gemessten akustischen Emissionen berechnet werden.

Jan 1, 2003

By K. -C. Han, S. -Y. Kim

This study was carried out in a bid to survey Ganboke gold mine in Pala, Mayo-Kebbi Province, southwestern Chad. The Ganboke mine is now being prepared for investigation and development, and the research sought to perform rock properties tests of relevant rocks through its geological survey, rock mass evaluation, and in-situ and laboratory tests and analyze the stability by the means of limit equilibrium method, thereby suggest appropriate methods to design the pit slope and individual benches in Ganboke mine. Targenting GS1-GS1' section with the depth of 180 m and GS2-GS2' section with the depth of 150 m in the survey area, we set the height of the bench at 10 m and 15 m, and the angle of bench at 60o and 70o, respectively, and then reviewed the stability for dried condition and saturated condition. The result of examination indicated that it would be appropriate to set the bench height at 10m and the bench angle at 60o in developing the mine slopes concerned. Cette étude est réalisé dans le but de faire des recherches sur Ganboke mine d'or dans Pala, Mayo-Kebbi Provence, Tchad sud-ouest. La Ganboke mine est actuellement en train de étre disposé à la investigation et le développement, et la recherche a cherché à accomplir les tests de la propriétè des roches par l'intermédiaire de la étude géologique, la évaluation de la masse rocheuse, et in-situ et les tests de laboratoire et à faire l'analyse de la stabilité au moyen de la méthode d'équilibre limite, de ce fait à proposer le methodes propres à faire le plan de la pente et les gradins individuels dans la Ganboke mine. Concernant la section de GS1-GS1' avec la profondeur de 180 m et la section de GS2-GS2' avec la profondeur de 150 m dans l'aire d'étude, nous mîmes l'hauteur du gradin à 10 m et 15 m, et l'angle du gradin à 60o and 70o, respectivement, et alors nous avon reconsidéré la stabilité pour la condition sèche et la condition saturé. Le résultat d'examen a indiqué que il pourrait être propre de mettre l'hauteur du gradin à 10m et l'angle du gradin à 60o en développant les pentes de la mine concerné. Diese Forschung wurde um das Gold Bergwerk zu überschauen in Pala, Mayo-Kebbi Provinz, der Südwesten Chad ausgeführen. Das Ganboke Bergwerk ist jetzt zur Erforschung und Entwicklung vorgebereiten worden, und die Forschung suchte zu ausführen die Prüfungen der Felseigenschaft durch geologischen Überblick, Felsmassewertbestimmung, und In-situ und Lavorversuch auf, und analysieren die Stabilität mittelst der Grenzegleichgewichtsmethode, da-durch schlug die angemes-sen Methoden zu entwerfen die Böschungen und die einzelnen Bänke im Ganboke Bergwerk vor. Für den Abschnitt GS1-GS1' mit der Tiefe von 180 m und GS2-GS2' mit der Tiefe von 150 m in der Überblickfläche, wir setzten die Bankhöhe an 10 m und 15 m, und das Bankwinkel an 60o und 70o, beziehungsweise, und dann zurückblickten die Stabilität für die getrockneten Bedingungen und die gesättigten Bedingungen. Das Ergebnis der Untersuchung anzeigte daß es würde angemessen sein zu setzen die Bqnkhöhe an 10m und das Bankwinkel an 60o in der Entwickelungen vom Bergwerk be-teiligt.

Jan 1, 2003

By A. Tosun

Muckpile fragmentation formed by blasting depends on the specific charge factor, the discontinuities in the rock mass, and the rock strength. Determination of the discontinuity characteristics and rock strength is a long and difficult process. These two parameters are directly associated with the rock drilling speed. Therefore, it is the drilling speed of the machine used for the blast-hole, rather than the blasthole discontinuity characteristics and rock strength parameters, that is used in the prediction of muckpile fragmentation before blasting. Primarily, it has been suggested that the muckpile fragmentation values can be correctly determined by establishing correlations between the efficiency of the loader and muck pile fragmentation, since fragmentation is directly correlated with the former parameter. Subsequently, a correlation predicting the drilling speed of the drill machine was developed according to the discontinuity characteristics of the blasting surface and the rock strength. Finally, a correlation was developed predicting muckpile fragmentation according to the specific charge factor and the drilling speed of the drill machine The data was obtained by conducting blasting tests in two different limestone quarries.

Nov 30, 2022

By J. Autio, H. Malmlund

The excavation damage zone (EDZ) caused by drill and blast excavation consists of intense damage adjacent to the remaining half barrel of the blast hole, new fracturing induced by the blast and reactivation of pre-existing fractures. The properties of intense microfracturing adjacent to the half barrels of remaining blast holes are based on study of rock samples from ZEDEX-tunnel and it’s extension at Äspö and the Research tunnel at Olkiluoto in Finland. The new and reactivated fracturing is based on results of mapping of slots cut in the rock in ZEDEX-project. The zone of increased porosity adjacent to half barrels, which penetrates to a depth of some centimeters was studied by using novel 14C-PMMA method. The penetration of the radial fractures, which is an order of magnitude deeper, was studied by mapping using color penetrant. Results of EDZ studies carried out at Äspö HRL in Sweden and in Research Tunnel at Olkiluoto show that the properties of EDZ can be affected significantly by engineering design. The result imply that the additional pore volume caused by distinct fracturing around the blast holes caused by state-of-the-art smooth blasting technique could be of the same order as that of the damaged zone adjacent to the surface of the half barrels. Durch Bohr- und Sprengarbeiten entstandene Eigenschaften der Auflockerungszone: Die durch Bohr- und Sprengarbeiten entstandene Auflockerungszone besteht aus einem großen, an das Resthalbrohr des Bohrloches angrenzenden Schaden, neuer Rissbildung und einer Reaktivierung der bereits existierenden Risse. Die Eigenschaften einer immensen, an die Halbrohre der Restbohrlöcher angrenzenden Mikrorissbildung beruhen auf einer Studie über die aus dem ZEDEX-Tunnel gewonnenen Gesteinsproben und deren Fortsetzung im Untertage-Labor Äspö (Hard Rock Laboratory, HRL) in Schweden und im Forschungstunnel bei Olkiluoto in Finnland. Die neue und reaktivierte Rissbildung basiert auf den Auswertungsergebnissen der Schlitze, die bei dem ZEDEX-Projekt ins Gestein geschnitten wurden. Die Zone der vermehrten, an die Halbrohre angrenzenden Porösität, die in ein paar Zentimeter Tiefe eindringt, wurde anhand der neuen 14C-PMMA-Methode untersucht. Das Eindringen der etwas tiefer gelegenen radialen Risse wurde anhand eines farbigen Eindringungsmittels untersucht. Die in Äspö und Olkiluoto durchgeführten EDZ-Studien zeigen, dass die EDZ-Eigenschaften wesentlich durch Engineering Design beeinflusst werden können. Das durch Bohrarbeiten verursachte Hohlraumvolumen der Rissbildung um den Tunnel herum ist ähnlich wie das Hohlraumvolumen der Bruchzone um die Bohrlöcher herum. Caractéristiques d’une zone endommagée par le creusement résultant d’un creusement par forage et dynamitage: La zone endommagée par le creusement résultant d’un creusement par forage et dynamitage présente un endommagement intense adjacent au demi-cylindre restant du trou de mine, une nouvelle fracturation et la réactivation des fractures préexistantes. Les caractéristiques de la microfracturation intense adjacente aux demi-cylindres des trous de mine restants reposent sur l’étude des échantillons de roche en provenance du tunnel ZEDEX et de son extension au laboratoire souterrain d’Äspö (« Hard Rock Laboratory » ou HRL) en Suède et du tunnel de recherche d’Olkiluoto en Finlande. La fracturation nouvelle et réactivée repose sur les résultats du placement des rainures sur la roche dans le projet ZEDEX. La zone de porosité accrue adjacente aux demi-cylindres et pénétrant à une profondeur de quelques centimètres à fait l’objet d’études recourant à la nouvelle méthode 14C-PMMA. La pénétration des fractures radiales, considérablement plus profondes, a été étudiée par placement en utilisant un agent pénétrant coloré. Les résultats des études EDZ effectuées à Äspö et à Olkiluoto montrent que les caractéristiques de l’EDZ sont susceptibles d’être affectées de manière significative par la conception technique. Le volume vide de fracturation résultant du dynamitage autour du tunnel est du même ordre que celui de la zone concassée autour des trous de mine.service.

Jan 1, 2003

By C. M. Rule, A. K. Anyimadu, L. Knopjes

Ongoing development work on ultra-fine grinding for various applications at the Group?s concentrators has been conducted by Anglo Platinum over the last few years. Current potential applications for mainstream grinding and concentrate grinding are the subject of a group-wide research and development programme. The first 10 000-litre 2.6 MW IsaMill was jointly developed by Anglo Platinum, Xstrata Technology and Netszch for installation at the Western Limb Tailings Re-treatment project in Rustenburg, South Africa. The unit was commissioned in late 2003/early 2004, and has operated in an intermediate concentrate regrind application successfully since. This paper describes the operational performance to date, as compared with the original duty specifications and objectives. The first mainstream M10 000 IsaMill with a 3 MW drive will be operational in November2006 at the Potgietersrus Platinum (PPL) ?Platreef? Sandsloot Concentrator in South Africa?s Limpopo Province. Key Words: Western Limb Tailings Re-treatment Plant, IsaMilling, Platreef, Platinum, Palladium, PGMs, tailings.

Jan 1, 2006

Book review Proceedings of the Symposium on Mining Methods. London, Institution of Mining and Metallurgy, 1974. 160 pp. The Symposium was held from 30th October to 1st November, 1974, and the papers include an interesting range of subjects in coal-mining operations, covering the improvements achieved to date, current practice, and required development for the future. Salamon, M.D.G., and Oravecz, K. 1. Rock Mechanics in Coal Mining. 119 pp. NIM reports Report no. 1822 Stability constants and linear free-energy relations for the platimtm-group metals. (22nd Oct., 1976). Report no. 1852 A revised method for the dissolution of platiniferous materials by the sealed-tube technique. (18th Oct., 1976). Report no. 1828 y-picoline adducts of the nickel, copper, and zinc chelates of 2-thenoyltrifluoroacetone. (26th Nov., 1976) Report no. 1847 A pilot-plant investigation of a kinetic model for flotation.(19th Nov., 1976)

Jan 2, 1977

By F. W. Petersen

The Conference Minerals & Materials '96 was held in Somerset West, South Africa, from 31st July to 2nd August, 1996. It was organized by the Universities of Stellenbosch and Cape Town, the Cape Technikon, and the Western Cape Branch of The South African institute of Mining and Metallurgy (SAIMM). The three-day Conference was attended by 180 delegates, representing countries such as Australia, South Africa, United Kingdom, Finland, Sweden, Germany, Poland, Zambia, and Zimbabwe. The programme and associated exhibition were well organized, and each of the delegates received two volumes of proceedings containing the 77 papers presented at the Conference.

Jan 1, 1996