Search Documents

This report was limited to a search of available literature on under- ground methods to combat acid water pollution. From this review it is evident that very little work has been done in this specific area. It is also evident that there are specific areas of mining engineering and mining related hydrology and geology that need further research efforts to solve the many water problems. They are: (A) Composition, variation and availability for oxidation of sulfur in strata. (B) Rate of oxidation of sulfuritic materials. (C) In situ limestone and its influence on underground acid drainage. (D) Structural, stratigraphic and hydrologic character of old mining areas as a basis to make decisions about adjacent new mining areas. (E) Operational changes in mining methods to prevent pollution. (F) Sealants for underground coating to exclude water from contact with pyrite to inhibit formation of the contaminants. Such a program has been initiated on refuse piles. The prime purpose of this report is to investigate those practices which have been used to regulate or control water accumulation and prevent harmful mine drainage. A supplemental purpose is to indicate those areas which need further research to prevent underground mine water pollution.

Jan 1, 1970

In the three years to June 2005, 959 injuries associated with continuous miners (CMs), shuttle cars (SCs), load-haul-dump and personnel transport (PT) were reported by NSW underground coal mines, comprising 23% of all injuries reported. The present paper reports an analysis of the narrative field accompanying these reports to determine opportunities for controlling injury risks. The most common combinations of activity and mechanism were: strain while handling CM cable (96 injuries); caught between or struck by moving parts while bolting on a CM (86 injuries); strains while bolting on CM (54 injuries); and slipping off a CM during access, egress or other activity (60 injuries). For the other equipment considered, the common injury mechanism was the vehicle running over a pothole or other roadway abnormality causing the driver or passengers to be injured (169 injuries). Potential control measures include: monorails for CM services; hydraulic cable reefers; handrails on CM platforms; redesign of CM platforms and bolting rigs to reduce reach distances during drilling and bolting; improvements to guarding of bolting controls; standardisation and shape coding of bolting controls; two handed fast feed; improvements in underground roadway maintenance, vehicle suspension, visibility and seating; and pedestrian proximity warning devices.

By M. J. Ferrante

New data on zirconium tetraiodide (ZrI4) have resulted from high-temperature enthalpy and X-ray powder diffraction studies conducted by the Bureau of Mines. These studies were undertaken as part of the Bureau's efforts to provide important thermodynamic data essential to the advancement of mineral resources technologies that can be employed with minimal energy requirements and minimal environmental degradation. Enthalpies were measured with a copper-block drop calorimeter. No transitions or other anomalies were found. Tabulated values are given from 298.15 to 772 K for relative enthalpy, heat capacity, entropy, and Gibbs energy function. Enthalpies are expressed in equation form and combined with data from the literature to calculate values of the standard enthalpy of formation and the Gibbs energy of formation. X-ray powder diffraction data indicate that ZrI4 is primitive cubic with a lattice parameter of 11.79 A and is isostructural with stannic iodide (SnI4).

Jan 1, 1980

By T. G. Carnahan

The Federal Bureau of Mines investigated, on a laboratory scale, a technique for recovery of silver from pregnant solutions generated in the hydro-metallurgical treatment of complex base-metal sulfide concentrates with oxidizing chloride media. This technique provides a means for recovery and simplified reduction of accessory silver to metal from chloride solutions. The method consists of adding NaI or KI to the solution to precipitate AgI, which is then contacted with Na2S to produce Ag2S and to regenerate the iodide salt solution. Silver recoveries range from 99 pct with 20 pct excess iodide precipitant, to 92 pct when the theoretical stoichiometric amount of precipitant is employed. The Ag2S product can be reduced to silver metal by contact with aluminum chips in NaOH solution followed by purification with conventional fire refining techniques.

Jan 1, 1980

By Peter Kovalchikb, Gregory Colec, Syd Peng, R. J. Matetic, Jeffrey Petersond

Mine Safety and Health Administration (MSHA) data indicates that the roof bolting machine is third among all equipment and second among equipment in underground coal mining whose operators exceed the MSHA-PEL (Mine Safety and Health Administration-Permissible Exposure Limit). In response to this, the National Institute for Occupational Safety and Health (NIOSH) has conducted a study to reduce overexposures of noise to operators of roof bolting machines. An important segment of the research is to determine, characterize and measure sound power levels radiated by a roof bolting machine during different drilling configurations. The determined sound power levels generated during the drilling cycle are of major interest because the levels represent the overall sound power generated by the machine. These sound power levels, determined from laboratory tests, can be used to accurately assess the effectiveness of proposed controls for reducing noise exposure to roof bolting machine operators. By using the sound power level results obtained from the laboratory and a commercially available acoustical modeling package, a method for predicting sound pressure levels to roof bolting machine operators for differing drilling types and parameters could be determined. This paper provides a method for predicting sound pressure levels at the operator’s position of a roof bolting machine in an underground coal mine using sound power levels determined in the laboratory. To determine validity, underground coal mine data was also collected to compare predicted and measured sound pressure levels. The results of the predicted sound pressure level data were the same as the underground measured results. This research will provide the mining industry with a valid method for predicting a roof bolting machine operator’s noise dosage underground given any type of drilling configuration or drilling method utilized from laboratory testing.

Native asphalt was produced in 1977 by six companies in four States. Leading States were Texas and Utah. Output declined 39% to 1,237,000 tons valued at $18,874,000. Bituminous limestone was produced by Whites Uvalde Mines and by Uvalde Rock Asphalt Co. in Uvalde County, Tex.; by Southern Stone Co. in Colbert. Ala.; and by Barton County Rock Asphalt Co. in Barton County, Mo. Gilsonite was produced by American Gilsanite Co. in Uinta County. Utah, and by Ziegler Chemical and Mineral Corp. in Weber County. Utah. The asphalt was used for streets and roads, and for other purposes.

Jan 1, 1980

"At the request of the Anthracite Institute, the United States Bureau of Mines during February, March, and April 1935, made a field survey of commercial anthracite shipped from collieries scattered throughout the Anthracite regions. In all, 268 samples were taken at 41 breakers from Carbondale at the northern end of the field to Pottsville at the south. These collieries ship approximately 50 percent of the industry’s total production. The geographical distribution of the breakers sampled was as nearly as practicable in proportion to the tonnage of the companies from each region cooperating in the plan.The following are the weighted average analyses, by sizes, of the samples taken in this survey;"

Jul 1, 1935

By Edward A. Barrett, Roberta A. Calhoun

Introduction This Instructor’s Copy contains most of the materials trainers will need in order to use Drill Rig Incident (DRI). It includes suggestions for using the exercise, performance objectives for the training, master answer sheets, a scoring key, and a set of discussion notes that provides additional subject information. Four appendices are also included. Appendix A is the complete exercise problem booklet. It may be reproduced so that every person in the training class has one. Appendix B contains answer sheet blanks. The blanks are furnished if you choose to have the invisible ink answers that appear in appendix C printed on them at your location.3 Answer sheets are consumable. One is needed for each group of three to five persons who work the exercise together. An alternative is for each individual trainee to have his/her own answer sheet. Appendix D contains the 24-question pretest / posttest that was used in the field evaluation of the DRI exercise. Acknowledgment The authors thank Linda J. McWilliams, Statistician, NIOSH Pittsburgh Research Laboratory, for her assistance in analyzing the experimental data in this document.

Jan 2, 2005

Provide a simple and effective means of measuring mining-induced pressure changes in coal mine roof and pillars. Approach Develop a reliable, easy to fabricate and install borehole instrument which measures mining-induced pressure changes in pillars and in the mine roof. Ground pressures are monitored through use of aluminum platens coupled with d copper flat jack. How It Works The Bureau's instrument measures mining-induced pressure changes by transmitting strata pressure through the aluminum platens to an oil-filled borehole platened flat jack (BPF). Pressure in the flat jack is displayed on a gage located outside of the borehole. The instrument is in-stalled in the borehole by inflating the flat jack using a hand-held hydraulic pump. In addition, the platens have been designed to allow up to three BPFs to be installed in a single borehole, thus permitting pressure change measurements in more than one direction from a single borehole. Installation pressure is calculated on the basis of the estimated pressure exerted by the overburden and the percent of recovery after intial mining has

Jan 1, 1986

By F. S. Karn

Measurements were made of the flow of helium, methane, ethane, butane, and toluene through thin disks of coal. All measurements were made on a dense layer in the Pittsburgh seam identified as attritus. Flow increased with pressure differential and temperature. At room temperature and a pressure differential of 1 atmosphere flow rates along the bedding plane of Pittsburgh seam coal were helium 881 X 10-10 cm2 sec-1, methane 1.2 X 10 -10 cm2 sec-1, ethane 0.54 X 10-10 cm 2 sec-1, n-butane 0.35 X 10-10 cm2sec-1, and toluene 3.8 X 10-10 cm2sec-1. Flow rates were 50 percent lower across the bedding plane of the coal than along the bedding plane. Activation energies were 3.9 kcal mole-1 for helium and 13.6 kcal mole-1 for methane, with diffusion measured either along or across the bedding plane.

Jan 1, 1970

To improve mining safety and efficiency by providing a practical way of detecting faults and channel sands that disturb coal seams. Approach A seismic system using a shallow blasthole has been developed and tested. How It Works A small shock is caused in a shallow hole, sending seismic waves through the ground. These waves are reflected from the top of the coal seam, acid are detected by a line of geophones on the earth's surface. Dampening of the seismic signals by channel sands and other discontinuities in the seam is detected and recorded. See Figure 1. The seismic shock wave can be produced by exploding small charges, dropping a weight, firing a gas gun, or actuating a vibrator. Depending on the soil cover, the shock is usually generated in shallow vertical holes about 10 feet deep. Hole depth depends on the soil mantle thickness because it is preferable that the seismic shock originate below that layer.

Jan 1, 1976

Develop new technolgies and techniques which enable recovery of strategic and critical minerals such as cobalt from domestic resources, thereby easing the U.S. dependence upon foreign producers for these valuable commodities. Approach The Bureau of Mines, through research, developed a process which uses mineral beneficiation techniques to recover cobalt-rich products from Missouri lead ores. Before development of this process, cobalt was lost as an impurity in the copper, lead, and zinc concentrates and in the mill tailings because the technology to recover it with minimum impact on present production did not exist.

Jan 1, 1989

By Pablo Velasco

Ecuador had limited mineral output, al-though the Government attempted to stimulate metallic mineral exploration and also evaluated a gypsum and a phosphate deposit. A pilot plant to exploit gold deposits was established, and there was extensive gold exploration activity in southern Ecuador. Domestic output of iron and steel declined sharply. Among all minerals, petroleum output was the dominant factor with both exports and production increasing significantly over that of 1988. Crude oil exports contributed 63% of total export earnings and about 70% of the central Government's revenue.

Jan 1, 1986

By Robert P. Vinson, John C. LaScola, Fred N. Kissell, Edward D. Thimon

The face ventilation measurement method developed by the Bureau of Mines involves releasing a small volume of tracer gas (SF6) on the off-curtain side of the working face at the start of the mining cycle. At the same time, gas bottle samples are taken in the immediate return airway. The gas samples are analyzed, and a curve is drawn of SF6 concentration versus time. From this curve, the percentage of gas removed per time is calculated. A curve showing a high percentage of the tracer gas removed in a short period would represent a well-ventilated face. The face ventilation measurement method was tested in a full-scale mine entry model. Subsequently it was used underground to evaluate the spray-fan ventilation system and in an MSHA test facility to test machine-mounted scrubbers. The method was shown to be a simple and effective way of evaluating face ventilation systems.

Jan 1, 1980

By E. G. King

Enthalpy increments above 298 K were determined by the Bureau of Mines for magnesium hydroxide (brucite) between 298 and 900 K by the method of drop calorimetry. Enthalpy and entropy increments from this investigation were combined with other data from the literature to calculate absolute entropies, free energy functions, enthalpies of formation, Gibbs energies of formation, and equilibrium constants of formation from 298 to 900 K. By the use of published PVT data for water, a table of Gibbs energy change was given for the reaction MgO (periclase) + H2O = Mg(OH)2 (brucite) as a function of temperature and pressure.

Jan 1, 1975

By E. C. Bennett

"INRTODUCTIONVarious methods of making leakage tests have been tried during a study of losses in the transmission of natural gas. This work has been carried on by the Bureau of Mines in cooperation with the Natural Gas Association of America. Results of torts show that the ""shut-in -pressure-drop"" method described by Rawlins is the most accurate and reliable; therefore its use is recommended. This paper describes a graphic method for computing the rote of leakage from the fall in pressure and change in temperature determined by the ""shut -in pressure-drop"" method of testing.METHOD OF MEASURING PRESSURE DROPThe gas is ""shut in"" line to be tested and is not allowed to escape except through existing leaks. The leakage causes the pressure in the line to fall. The charge in pressure is obtained with a dead weight gage. Approximate results may also be obtained from readings on a good spring test gage. Numerous tests show that the dead weight gage is more sensitive to small changes in pressure than spring gages.The temperature of the gas in the line is observed simultaneously with each pressure reading. Temperature changes affect the pressure exerted by a given quality of gas ""shut in a line, end since the rate of leakage from a closed system is directly proportional to the rate of pressure drop, fluctuations in temperature must be considered."

May 1, 1926

By Fred Baldassare, Marcia Harris, Kenneth K. Eltschlager

Surface mine blasting was recently investigated as a potential source of high concentrations of stray gases found in nearby residences of western Pennsylvania. In one incident carbon monoxide was detected in a home and in the other, high concentrations of carbon dioxide were found in a home. Both carbon monoxide and carbon dioxide are by-products of blasting. However, other potential sources of these gases may also exist in a residential setting. In each case, gas chromatography (GC) and carbon isotopic analyses were used to define atmospheric concentrations inside the homes, and to determine the source of a stray gas. Molecular and isotopic analyses provide geochemical evidence as to the origin and source of the stray gas. This paper discusses elements of a stray gas investigation and the analyses necessary to identify the source of a stray gas.

By John J. McClelland, Gerald T. Homce, John R. Thalimer

The U.S. Bureau of Mines has investigated the early detection of insulation failure in squirrel cage induction motors for the past 4 years. Research was done using a sophisticated empirical data-modeling technique based on values calculated from a motor's voltage and current phasors. This technique produces two polynomial equations that calculate the insulation leakage current and power. These models were implemented in a prototype system that monitors six motors on a continuous miner for insulation leakage. These insulation leakage values are used to anticipate insulation failure. The system consists of a motor-data-system for each motor on the machine and a control computer located away from the miner. Each motor-data-system consists of an analog interface to the motor's voltages and currents, a single-board computer that reads digitized data and calculates voltage and current phasors, and a bus node that interfaces the single-board computer with the rest of the system by way of a serial bus system. Using this bus system, the control computer requests and receives phasor data from the motor-data-systems. From these data the control computer calculates and displays two deterioration values for each motor, for leakage current and power, using Bureau-developed models. These values are stored in a data base from which the user can display graphs of each motor's deterioration values over time.

Jan 1, 1992

By J. M. Stuve

Calorimetric determinations of the low-temperature heat capacities, standard enthalpy of formation, and high-temperature enthalpies were made of (Na20)4 ?Fe20,(c). The resulting values of entropy (S°), enthalpy of formation (?Hf°), and free energy of formation (?Gf°) at 298.15° K are 104.676 cal/deg mole, -656.2 ±.kcal/mole, and -603.4 A kcal/mole, respectively. Tabulations of Cp°, S°, - (G°-H°298)/T, H°-H°298, ?Hf°, ?Gf°, and log Kf are given to 1,200° K.

Jan 1, 1971

Permit visual inspection of underground cavities dam the surface. Approach A closed circuit TV camera and a 35mm still camera are lowered down a borehole, and remotely operated. How It Works A platform holding the cameras, and other equipment is lowered on a graduated cable until the depth of interest is reached. Then a quartz lamp and the TV camera are turned on. The television picture is monitored at the surface and recorded on video tape. Areas of special interest are photographed with a 35mm still camera. These photographs contain more detail than TV images because photographic film is capable of higher resolution than a TV transmission.

Jan 1, 1979