Search Documents

Objective To improve seats on mine shuttle cars with ergonomic design and by reducing shock impact transmitted through the mine vehicle seat to the vehicle operator. Background Operators of underground mobile equipment, particularly shuttle cars, are often exposed to significant levels of shock and whole-body vibration. Past studies have reported that as many as one-third of underground equipment operators could be exposed to adverse levels of shock and whole-body vibration. Moreover, seats on mining equipment, historically, are inadequate relative to the ergonomic needs of the equipment operator. In the extreme, amine vehicle seat has sometimes consisted of blocks of wood or a bent steel plate bolted to the machine frame. Also, the lack of sufficient vertical clearance in some underground mines is an impediment to providing adequate shock isolation systems on mine equipment seats. Approach The NIOSH Pittsburgh Research Center (PRC) is conducting research with viscoelastic foams to improve seats on mine shuttle cars. Viscoelastic foams were used in an ergonomically designed seat to reduce the amount of shock transmitted through the mine vehicle seat to the vehicle operator. Data on selected viscoelastic foams were analyzed from laboratory shock tests at PRC. Using information from the analysis, two ergonomic seats incorporating selected foam were constructed for in-mine testing on a shuttle car (Joy 21SC) in eastern Kentucky. The shuttle car operated in a 35-in-thick coal seam with an approximate mining height of 43 in. Operational data were recorded on the ergonomic and original seats. Further, the shuttle car operator was asked to compare these seats. Results When comparing the original seat (figure 1) with the ergonomic seat (figure 2), the shuttle car operator described the ergonomic seat as generally “much better” than the original seat. The operator explained. “It’s just easy to adjust. And it’s got the lower lumbar support. And the pad is thicker. It’s just much better all the way around.” He added, “It does support you more and [there is] less shock when you hit a hole...I liked the lower lumbar support. That’s where most of your shock is at, in your lower back.” The operational data supported the operator’s comments. In the full-load case, significant improvements in isolation were achieved(down to 15 Hz) with the ergonomic seat. Additional laboratory testing of seven viscoelastic foams was done to further improve the level of isolation from shock and better characterize the material properties of each foam. Data from this testing were used in an analytical model of the seat pan isolation system. Results showed that two of the viscoelastic foams, SUN-MATE EXTRA-SOFT and PUDGEE, gave the most effective shock isolation of the seven materials tested. A composite of EXTRA-SOFT and PUDGEE foams improved the isolation characteristics of the seat pan to approximately 4 Hz. Similarly, EXTRA-SOFT by itself provided isolation to 5 Hz. These results will be validated with future in-mine measurements. Cooperative Research Opportunity NIOSH is seeking cooperators to assist in further research and development of this technology. Additional information on cooperative reseach may be obtained by contacting Jacqueline H. Jansky, Technology Transfer Officer, NIOSH Pittsburgh Research Center, P.O. Box 18070, Cochrans Mill Rd., Pittsburgh, PA 15236-0070, phone: (412) 892-6615, fax: (412) 892-6678, e-mail:jgj7@cdc.gov

May 1, 1997

By W. J. Pena, C. W. Owings

"Generally, the hazard of cool-dust explosions in tipples and cleaning plants is not given the consideration that is given it underground. This lack of consideration is probably due to failure to appreciate the potential hazard. An explosion in a tipple or cleaning plant is basically little or no different from an explosion underground. If bituminous-coal dust is raised into a cloud in the air and comes in contact with arcs from motor brushes, switches, or open flame, the dust is very likely to ignite, and flame will very probably propagate or extend through it if the quantity of dust per unit of air space is sufficient. The open space in a tipple or cleaning plant may reduce the violence of the explosion, but it is not likely to prevent ignition or propagation of flame.The movement of coal through a tipple or cleaning plant naturally puts into suspension a large amount of dust, which finally settles on exposed surfaces. Any disturbance that will put this dust into suspension in a sense enough cloud can result in the dust being ignited by an arc or open flame if one should be present. An explosion of bituminous-coal dust in a tipple or cleaning plant generally can be prevented either by keeping it thoroughly clean or by removing all sources of ignition, or both.The tests at the U.S. Bureau of Mines Experimental mine have shown that the explosibility of coal dust is proportional (other things being equal) to the ratio of the volatile matter to the volatile matter plus the fixed carbon, indicated thus:The volatile ratio for the Pittsburgh coal bed is calculated as follows:Therefore, as the volatile matter decreases the liklihood of ignition decreases; however, coal-dust explosibility depends on other factors also, such as fineness, dryness, and cloud density; and under some conditions other factors also intervene.Proof of the explosibility of coal dust in the absence of explosive gas has been shown in numerous cases in mines and mine plants and also by a series of tests. In these tests a dense cloud of dust is blown onto an open flame or an electric arc, almost invariably with resultant exploding of the dust. The Safety Division of the United States Bureau of Mines has made a number of demonstrations of the explosibility of Pittsburgh coal-bed dust, using a small gallery or box in which a cloud of coal dust is blown onto a lighted match; larger-scale tests have been made with an electric arc as the igniting agent. Bituminous-coal dust is readily ignited with a medium arc, but with low-volatile coals a larger arc is required. For test purposes, a 100-ampere arc has been used. Ignition has occurred readily under these conditions with Pocahontas No. 5 coal dust with ratios of volatile to total combustible of 0.232 to 0.253, and with Pocahontas No. 3 coal dust with a combustible ratio of 0.242. Lower Kittanning coal dust, with a ratio of 0.187, did not give definite ignitions, and Pocahontas No. 4 dust did not explode, although part of the coal-dust cloud ignited. It is probable that even the low-volatile coal dust will be found to be explosive with a higher-amperage electric arc as the initiating agent."

Jul 1, 1936

By D. Harrington

"Since its establishment in 1910 the Bureau of Mines has consistently recommended the rock-dusting of bituminous and lignitic coal mines as a preventive of widespread explosions. As with many other proposed innovations, the response to the bureau's recommendation has been slow; but during the past 10 years many coal mines have done some rock-dusting, even though probably fewer than 50 of the country's approximately 6,000 coal mines are thoroughly rock-dusted. Notwithstanding the inadequacy of the rock-dusting which has been done in most of the mines which have adopted the new system, numerous cases are at hand. indicating the well-founded basis of the bureau's claims regarding the effectiveness of rock-dust in stopping explosions. Very brief descriptions will be given of several cases in which explosions in coal mines of the United States are fairly definitely known to have been stopped by rock-dust during the past 5 or 6 years; in addition, several cases are cited in which explosions were stopped through the agency of rock-dust and moisture.A rock-dusted mine is one in which the floor, roof, and sides of every accessible working place, including haulage ways, airways, manways, and rooms and connections have an application of rock-dust - for instance, limestone - such that the incombustible content of the aggregate dust on those surfaces is over 60 per cent. The dust in these workings should be sampled at regular intervals to determine whether the incombustible matter in the coal-dust is less than the necessary minimum of 60 per cent; another application of rock-dust should be given when the incombustible percentage is less than 60. (As an example of thorough rock-dusting, see Bureau of Mines Information Circular 6578, 1932, which describes how rock-dusting is done in Alabama at a cost of 1.8 cents per ton of coal for a thorough application; Report of Investigations 3060, February, 1931, Rock-Dusting In A Pennsylvania Coal Mine; or Information Circular 6244, 1930, giving data, including costs, on rock-dusting in coal mines in New Mexico.)An explosion may be started by the ignition of gas, even when rock-dust is present; hence it is not correct to say that rock-dust will prevent an explosion of gas; however, if rock-dust has been applied to a working place which has present an explosive mixture of me-thane and air, and if an open light is used or a blown-out shot or an electric arc occurs, although there will very likely be an ignition and possibly an explosion, the rock-dust will certainly prevent ignition of the coal-dust nearby, and unless the general atmosphere has an explosive gas mixture, the rock-dust will stop propagation of the flame throughout the mine. In other words, if an explosion is started by gas or by coal-dust and the mine has been rock-dusted as defined, the rock-dust will prevent widespread extension of the explosion, unless the general atmosphere contains methane and air in explosive proportions.With these definitions clearly in mind, instances are now given where rock-dust has played a prominent part in the stopping of several explosions. No cases have been included where there was any reasonable doubt that rock-dust had taken a definite part in the limiting of the explosions."

Apr 1, 1932

By E. H. Denny

"Reduction of mine accidents appears to depend upon essentially the same fundamentals, whether considered from the viewpoint of the mine operator, miner, State mine inspector, or safety engineer. Conditions of mine operation with respect to safety are governed in most States by a mining law, usually somewhat general in its provisions but more specific than laws dealing with other industries, Methods of mining development and practice evolved through experience have been handed down from generation to generation; many of these are intended to avoid injury to men and also loss of property. To carry out the intent of these bases of law and experience relating to safety supplemental measures and conditions are necessary. Among these may be: (1) Planned safety rules adapted to the mine and compliance by both officials and Miners with such of these rules as pertain to their work; (2) a supervisory force adequate and competent to ¬administer the mining laws and safety rules; (3) discipline adequate to secure compliance with safety measures; (4) safeguards against mechanical, electrical, falling, and other hazards; (5) mining operations planned with respect to safety of workers; (6) an active safety organization of officials and employees; (7) education of officials and employees in safety practices; and (8) an active sustained interest in safety by management and employees.This paper presents the viewpoint of the safety engineer, though a safety engineer connected with a specific mine or group of mines would be in a better position than the writer to present the industrial engineer's thought. The application of the mine safety fundamentals just outlined will be given consideration from observations of methods used by safety engineers and supervisors.The term ""safety engineer"" includes men of various duties, various degrees of experience, and various authority. Depending upon the size of the operation or the interest of the management in safety, the safety engineer may have accident prevention as his sole duty; he may be the head of a sizable safety organization; or he may be in part a claim agent; a statistician compiling figures for the enlightenment of the company, the public, or a mining institute meeting; a surveyor who must convince the miner that his scale of 10/10 equals 1 foot does not defraud the miner of 6 inches to every yard measured; or he may be by heaven¬ly gift an orator capable of assuring the employees that ""all's right with the world""; he may be a young engineer gaining, experience while checking the observance of company rules and investigating accidents; or he may have the physical ills frequently resulting from several decades of mining experience and instead of a pension, the position of safety engineer has fallen to his lot. He may have mine-operating authority to correct immediately a dangerous condition or practice or he may have his recommendations officially disregarded at the monthly meeting or when the bottom of the desk basket is reached. He is likely to find that his viewpoint on accident reduction is considered unsound today because of youth and inexperience and unsound later because of old age and senility. He is likely to find the easiest course to be that of attributing to Providence and the carelessness of the worker the mishaps that result in the removal of a man to the hospital or the morgue."

Dec 1, 1936

By R. H. Kudlich

In order to assist the various Federal and State agencies using large quantities of coal to select coal best suited technically and economically to their use, the United States Bureau of Mines has placed at their disposal a fuel inspection service. As part of this service, inspections are made at the mines which propose to furnish coal to these agencies on contracts. Such inspections cover both the mine itself to ascertain its capacity to fur- nish the desired tonnage and quality of the coal, the preparation of the coal in the tipple, and the obtaining of samples for analysis to determine the quality of coal as shipped. To insure that the sample sent to the laboratory for analysis is representative of the average quality of the coal, increments are taken at intervals until a gross sample of about 1,000 pounds of coal has been collected from each of the sizes of coal shipped by the mine, while coal has been coming from all parts of the mine. In reducing this gross sample to the small sample which is sent to the laboratory for analysis it is necessary to crush and quarter the coal by a certain standardized method until only 5 or 6 pounds of coal small enough to pass through a 3/16-inch square-mesh screen remains. The ordinary method which the bureau has followed was to crush the coal by hand with a tamper, such as is used for tamping concrete, on some hare smooth surface and to reduce the volume by quartering and riffling. During the past few years the demands from various Federal and State agencies for this service have been increasing rapidly in respect to bituminous coals. In addition to this, which might be called the normal increase, numerous requests have been received for similar service in respect to anthracite. It was obvious that if this increased demand was to be met it would be necessary either to increase the force allotted to this work or to provide the present force with some means by which their work could be made more effective. A care- ful survey of the situation showed that the greatest amount of time was consumed in trans- porting the men and their equipment from mine to mine in the same district, and in reducing the gross sample to the small finely crushed sample which is to be sent to the laboratory. Both of these phases of the work could be greatly accelerated by providing a motor truck of suitable speed and capacity, carrying a power-operated crusher, and the proper auxiliary equipment to store the gross sample as collected and to reduce it in volume efficiently after it has been crushed. Such a truck has been provided and placed in service. In the eight months it has been in operation the desired results have been fully attained. About twice as many samples as usual have been taken during that time by the same 2-pan crew assigned to this work. Many of the mines in the eastern part of the United States are in hilly or mountainous regions and can be reached only over rough, practically unimproved roads. Hence the speci- fications for the truck were drawn to cover high-quality, long-life trucks, in order that

Nov 1, 1931

Background Carbon monoxide (CO) is an odorless, colorless gas that can cause illness and death by asphyxiation. Although the toxicity of CO is understood, CO exposure can occur from unrecognized sources. On April 2, 2000, a couple and their newborn infant were poisoned by CO migrating through the ground from blasting at a nearby coal strip mine into their home near Kittanning, Armstrong County, PA. They were treated at the hospital and diagnosed with CO poisoning. The infant had a carboxyhemoglobin level of 31%, the father 28%, and the mother 17%. Carboxyhemoglobin is the compound formed in the blood when CO is breathed. Persons not exposed to CO have carboxyhemoglobin levels of 0.3%-0.7%, and cigarette smokers have levels of up to 9%. Following release from the hospital, the family installed a CO detector in the basement of their home with the help of the local fire department. This Technology News briefly describes this incident to help increase awareness of the problem. It is discussed in more detail by Eltschlager et al. [2001]. Figure 1 shows the coal strip mine believed to have generated the CO. The initial suspect for the source of the CO was the furnace in the house. Only later did it become apparent that blasting at the nearby strip mine might be the culprit. A State investigation concluded that CO had migrated approximately 500ft from the blast, through the ground, and into the home. Figure 2 shows the locations and order of blasts at the mine. Initially, the mine did not plan to blast. Overburden generally consisted of weathered shale that could be dug without blasting. However, the mine decided to blast when hard sandstone that could not be dug out was encountered within 3 ft of the coal top. The blasting was intended to break up the sandstone. Blasting was done using bulk ammonium nitrate-fuel oil (ANFO) in 6.25-in holes 25-30 ft deep on a 16-ft by 16-ft pattern, with charge weights ranging from 17 to 170 lb. The closest blast to the home was 430 ft on April 17, 2000. The distance from the home to the blast area on the day when CO was first reported (March 31, 2000) was 500 ft. Twenty blasts were detonated at the mine between March 7, 2000, and April 20,2000. The blaster was careful to prevent fly rock since another home was only 150 ft away and a garage was 50 ft away. The quantity of explosive used in the blasts was sufficient to break the sandstone, but was less than would normally be used to blast overburden. The holes were typically one-third explosive and two-thirds stemming, with powder factors averaging 0.43 lb/yd3. Additionally, the muck was not immediately excavated after each blast. The heavy confinement on the explosive acted to prevent the typical release of blasting fumes into the atmosphere. Instances of CO migrating from blasts into homes have occurred before, but generally the distances involved were under 150 ft. It is believed that the blast design contributed to the confinement of CO in the ground, and discontinuities in the ground strata facilitated migration toward the residence. Upon inspection of the blast pitwall, a regular system of joints was observed. These joints are oriented roughly from the blast pit toward the house (figures 3-4).Blast-generated CO appears to have been driven into the joint system, displacing the air. When the joint system was saturated, the next succeeding blast pushed the CO into an uncased well next to the house (a high level of CO has been measured in the well shortly after a blast). From there, the CO entered the French drain system and then the basement of the house. The joints are vertical cracks through rock layers that occur on a regular spacing (figure 3). They are most common near valley slopes and are caused when valley walls converge as the stream cuts down through the rock layers. Often called hill seams, they roughly parallel the valley walls, but can curve and split, creating a pathway for gas movement (figure 5). These fractures are often encountered when underground mining proceeds close to outcrop. The system of fractures at the Kittanning blast pit was well developed and provided a path for transmission of CO both through the sandstone and up and through the overlying shales. Blasting engineers should be able to distinguish naturally occurring fractures from blast fractures and note the frequency, development, and orientation of the hill seams and their proximity to occupied houses. The limits of transmission of

May 1, 2001

By A. T. Iannacchione

Synopsis Underground stone mining Is an emerging sector of the U.S. mining industry. As this expansion takes mines under deeper cover, and as more efficient mining methods are utilized, effective stone pillar design methods will become even more Important. Current design practices are examined and a discussion of safe mine layouts is presented as a first approach towards weighing the demands for increased production against increased risk. Risks to underground stone-mine workers include rib Instabilities, pillar failures and roof falls. Seventy-two stone-mine pillar designs were examined. Pillars with width to height ratios of less than 1.5 appear more likely to fail when subjected to excessive stress levels. When width to height ratios fall below 1.0 defects in the pillars, such as through-running discon¬tinuities, can have a significant influence on stability. Discontinuity persistence, dip, material properties and orientation are also important determining factors in pillar strength. During the past three years the number of active underground stone mines in the U.S.A. has ranged between 90 and 100. This number is expected to increase as the crushed stone industry responds to growing demands for its products.1 As more of the industry moves to benefit from the advantages of underground mining production from underground stone mines is expected to increase above its current level of approximately 66 000 000 r/year. Parker2 identified four advantages of underground mining operations: (1) surface developments, zoning laws and environmental concerns are often less of an issue; (2) stripping and restoration requirements are eliminated; (3) additional reserves are often available beneath the quarry floor, under pit slopes or under an adjoining property; and (4) space is created for secondary use. Underground mines enjoy the added benefits of work in a constant underground climate, rather than in the variable surface climate, minimization of community concerns by placement of the crushing, sizing and stowing operations underground and reduction of surface vibration concerns through smaller blasts. The drawbacks of underground mining include added health and safety hazards for the stone miners, whose health can suffer from increased exposure to falls of ground, airborne contaminants and fog in large underground openings. Injuries from falls of ground in stone mines have occasionally exceeded the incidence rates for other mineral resources mined underground. 3 Existing underground stone operations, by comparison with stone operations a decade ago, mine more stone at a faster rate and with larger equipment. Because of high demand mines face increased pressure to yield more stone per production blast. A majority of the miners use the V-cut blasting pattern, which limits the depth or pull for each shot to about 4 m. Therefore, to produce more stone, either the mines must work more faces or existing faces must be enlarged. The enlargement of underground openings poses problems in the maintenance o€ strata stability, First, the widths of the mine entries partially control the amount of sag or deflection that any given roof beam can withstand before failure. This deflection can take pi ace quickly after an opening is excavated or much later as weathering processes form additional, thinner beams. Because increased deflection increases the potential for roof beam failure, there is a limit to how wide a room can safely be made. These limits depend on local geological and stress conditions and, to some extent, the cost effectiveness of roof-bolting. Given these room width limitations, underground stone mines have placed more attention on expansion of production through benching where mining thicknesses permit. The heights of rooms partially control the strength characteristics of adjacent pillars: as the room height increases for a given pillar width the pillar width-to-height ratio (w/h) decreases. In general, stone pillars are very strong, but when the width-to height ratio diminishes the potential for pillar rib instabilities and pillar failures increases (see Fig. 1). [ ] In the underground environment the desire to utilize wider rooms, higher benches and multi-level mining results in the potential for unstable ground conditions. Although the number of failed pillars is currently very low, the potential for additional failures will grow if more slender pillars are developed, especially under deeper cover, with wider mining sections and in multi-level operations. It should also be noted that the passage of time acts to decrease the strength of many existing pillars. An examination of current design practices

By R. Karl Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard for miners and mine operators. This type of failure, termed a 'cascading pillar failure' (CPF), occurs when one pillar in a mine layout fails, transferring its load to neighbouring pillars, which causes them to fail, and so forth. Recent examples of this kind of failure in coal, metal and nonmetal mines in the U.S.A. are documented. Mining engineers can limit the danger presented by these failures through improved mine design practices. Whether failure occurs in a slow, non-violent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This stability criterion is used as the basis for three design approaches to control cascading pillar failure in room-and-pillar mines-the containment approach, the prevention approach and the full extraction mining approach. These design approaches are illustrated with practical examples for coal mining at shallow depth. Cascading pillar failure {CPF) in room-and-pillar mines can go by many other names, such as `progressive pillar failure', `massive pillar collapse', 'domino-type failure' or 'pillar run'. In this kind of failure when one pillar collapses the load that it carried transfers rapidly to its neighbours, causing them to fail, and so forth. This failure mechanism can lead to the rapid collapse of very large mine areas. In mild cases only a few tens of pillars might fail; in extreme cases, however, hundreds, even thousands, of pillars can fail. CPF can have catastrophic effects on a mine, and sometimes these effects pose a greater risk to health and safety than the underlying ground-control problem. Usually, the CPF induces a devastating air blast as a consequence of the displacement of air from the collapse area. An air blast can disrupt the ventilation system totally by destroying ventilation stoppings, seals and fan housings. Flying debris can seriously injure or kill mining personnel. The CPF might also fracture a large volume of rock in the pillars and immediate roof and floor. In coal mines and certain other mines this can lead to the sudden release of large quantities of methane gas into the mine atmosphere; a methane explosion might result from the CPF. CPF is at the far end of the spectrum of unstable pillar failure. At the other end are slow `squeezes' that develop over days to weeks and, because of their slow progress, do not pose an immediate danger to mining personnel. There is ample warning time for men and machinery to get out of the way of the failure. In a CPF, however, the failure progresses so rapidly that men and equipment cannot be evacuated in time. Significant seismic energy is released as a consequence of the rapid failure and collapse. CPF should not be confused, however, with coal-mine bumps and rockbursts. In some cases the damage can appear similar, but the underlying mechanics are completely different. As will he shown later, the mechanics of CPF depend on the applied vertical stress and the post-failure, i.e. strain-softening, behaviour of the pillars. In a CPF pillars shed their applied load rapidly and have very little residual strength after failure. The collapse itself may release significant seismic energy, but otherwise the mine is seismically quiet. Alter a CPF the openings in the affected mine workings have usually closed completely. In contrast, coal-mine bumps and rockbursts occur in seismically active mines. Research has shown that coal-mine bumps and rockbursts are seismic events induced by mining that damage underground mine workings. Bumps and bursts are thus a subset of a much larger set of mining-induced seismic events.[ Only some of these seismic events damage mine workings; fortunately, most do not. The mechanisms by which a mining-induced seismic event can lead to a damaging coal-mine bump or rockburst is still a significant research area.2 After a bump or rockhursr the affected mine workings may or may not be completely closed. For example, in the coal-mine bump described by Soler and co-workers2 the mine workings remained open even though the pillars were destroyed during the bump event. Because CPF differs from a coal-mine bump or rockburst, the design approaches to control their occurrence also differ. The design recommendations developed here apply to CPF and not to bump- or burst-prone mines. Cascading pillar failure examples Unfortunately, CPF has occurred in room-and-pillar coal, metal and non-metal mines. The most infamous example is the Coalbrooke colliery in South Africa, where 437 miners perished where [si >1 3at1ttsumsus7car kky vArtMixiL7i nesafr tramwsamn ures] on 21 January, 1960.1 Table I summarizes the mining dimensions of 13 examples of rapid pillar collapse in U.S. coal mines. All occurred during the 1980s and 1990s, and all happened suddenly or without significant warning. Most resulted in air blasts and damage to the ventilation system. Table 2 gives the mining dimensions of six room-and-pillar metal and non-metal mines in the U.S.A. where failure occurred in all probability by the CPF mechanism. The collapse areas can be huge. Fortunately, some of these failures gave advance warning. At the lead-zinc mine slabbing from pillars and roof falls began four weeks prior to the main collapse.3 At the copper mine considerable rock noise and smaller failures preceded the main collapse by five days.5 At the copper-silver mine it is not known if nature provided a warning.6 Evidently, the trona mine collapsed without warning.7,8 Rock noise and other failure warnings preceded the silica mine collapse by three weeks. v The presence or absence of warnings at the salt mint is not known. to Most of these collapses induced a substantial air blast; damage to the ventilation systems was limited, however, to bent airdoors and a few downed stoppings, except at the trona mine where extensive damage to the ventilation system resulted.

By R. D. Currie

The practicability and dependability of two permissible methane-indicat- in detectors recently developed were proved conclusively by extensive tests in the return airways of all mines operating in the anthracite region in most of which samples and readings were taken with one or the other of the two in- dicating detectors. These detectors roved dependable and accurate within practical limits, and their general use should be encouraged as an aid to bet ter ventilation, more accurate control of air currents, and greater safety in mines.

Feb 1, 1936

By J. R. Thoenen

This circular is part IV of the third paper (entitled "Sand and Gravel Excavation") of a series summarizing the technical problems involved in the production and preparation of sand and gravel. Part I discussed the use of power shovels, draglines, and excavator cranes; part II discussed the use of power scrapers, slackline cableway excavators and hydraulic monitors; and part III discussed the use of hydraulic, clamshell, ladder, and dipper dredges. This circular discusses haulage equipment in general, particularly the use of industrial cars with locomotives or hoists as the motive power. Part V, to follow, will discuss the use of other types of haulage equipment.

Oct 1, 1935

By G. W. Jones, R. E. Kennedy

A simple , quick, and relatively accurate device is needed for determining the presence of very small concentrations of organic halide gases in various atmospheres . Such a device would enable safety engineers , health officials , and others to discover quickly the presence of these gases in a suspected atmosphere and thus be able to apply protective measures promptly. This detector should prove useful in detecting leakage of halide gases from refrigerating and air - conditioning systems and in determining the presence of halide solvents in the atmosphere of dry - cleaning and degreasing establishments where organic halide solvents are used . Virtually all poison war gases are halide compounds . Because of the high toxicity of these gases , even in very low concentrations , a detector having the proper sensitivity should be useful in civilian defense for determining when atmospheres are relatively free of poison gases .

Apr 1, 1943

By J. R. Nettle

The electrodeposition characteristics of seven binary alloys of titanium have been investigated. The object of the electrorefining experiments with an alloy was to determine the efficiency of titanium separation from individual alloying elements under established conditions. Reported results are only indicative. It is conceivable that numerous duplications of tests might give average maximums that would vary from those noted in this report; however, in the few tests that were repeated, the magnitude of transfer of the alloying elements was of the same order. The results detailed herein are for a given set of conditions. Many combinations of operating variables are possible, and the results achieved under different conditions probably would differ from those reported.

Jan 1, 1958

By David C. Oyler, William P. Diamond

Three long horizontal holes were drilled from a directionally drilled sur¬face hole at the Emerald Mine near Waynesburg, Pa. The purpose was to adapt the technique of directional drilling for use in draining methane from coalbeds. A 504-m (1,652-ft) long, 76-mm (3-in) diam¬eter, circular arc pilot hole was drilled, using a downhole mud motor, to enter the Pittsburgh coalbed at a verti¬cal depth of 305 m (1,000 ft). The hole was reamed to 222 mm (8-3/4 in) and was cased to a measured depth of 486 m (1,595 ft). Three 76-mm (3-in) diameter horizontal drainage holes were then drilled, totaling 2,909 m (9,544 ft) of horizontal hole. Improvements in drilling methods increased the average drilling rate from 20.4 m (67 ft) to 64.9 m (213 ft) per day. The cost of drilling the directional and horizontal holes (using a Government-owned drill rig) was $1,169,530, a figure inflated by inexperience and by delays caused by lost-circulation problems and fishing operations. An estimated total drilling cost of $960,000 (including rental of a drill rig) for an improved system, was determined by a detailed cost analysis. Initial gas and water production from November 1979 through May 1980 was low because of caving of the horizontal holes drilled in shale near the bottom of the casing.

Jan 1, 1982

By J. N. Van Sant

Lignite mining in North Dakota was begun about 1884 to supply the domestic needs of settlers. Annual production has grown rather slowly but steadily, exceeding 3 million tons in 1950. The western part of the State has lignite reserves, amounting to 351 billion tons, underlying an area of 28,000 square miles. Contour strip mining has almost completely replaced underground mining as the method of production. Lignite is often found under rather shallow and easily removed overburden, and this is the primary reason for the change in mining practice. Current mining operations are conducted where the overburden is 30 to 70 feet thick. Contour strip mining results in high production rates, at present 27 to 56 tons per man-day. These high production rates result in relatively low production costs.

Jan 1, 1959

By Walter C. Lorenz

Samples of materials containing pyrite from various coal mines and coalbeds were studied to compare their compositions and oxidizing characteristics. Pyrite was the only form of iron sulfide identified, but X-ray diffraction, emission spectrography, and microscopic analyses revealed similar suites of minerals and trace elements. The pyrite occurred usually in spherical clusters of very small crystals. The oxidation of pyrite in solutions of PeSO4 and Fe2(SO4)3 and in the presence of an iron oxidizing bacterium Ferrobacillus ferrooxidans, was studied through a manometric technique. FeS04 or Fe2(SO4)3 solutions had no appreciable influence on pyrite oxidation under the test conditions, The bacterium acted as a catalyst, greatly increasing the oxidation rates; however, in three samples that also contained calcites, bacterial oxidation was greatly reduced. The oxidation rates also increased approximately as the percentage of pyrite in the samples increased. For the series of samples studied, there was no definite correlation of the results with the location of the various mines nor with the acidity of alkalinity of the mine drainage.

Jan 1, 1963

By Otto Robert Stein

Erodibility of reclaimed surface mine soils is a subject in need of quantification. Effects of soil erosion from reclaimed areas may damage surrounding areas and the quality of water in nearby streams and lakes. It may also reduce the potential productivity of the reclaimed site. A study was conducted to determine erodibilities of different reclamation treatments and a nearby unmined soil at three Indiana strip mine sites. A rainfall simulator was used to artifically erode plots con¬structed within seven treatment categories and the unmined soil. Soil erodibility was assessed in terms of the Universal Soil Loss Equation (USLE) K factor. Values for K calculated from field data were compared to values predicted from independently measured soil properties. Differences in soil erodibility between treatments were site specific. Unmined soil had the highest calculated erodibility at one site but at two other sites soils having reclaimed A horizons were highest. Shaley overburden treatments had the lowest calculated erodi¬bility. Predicted soil erodibility was usually lower than that calcu¬lated from field data. Site specific slope gradient factors (S) were developed for reclaimed A horizon treabnents. This was done because the USLE S factor overestimated the measured soil loss at steeper slopes.

Jan 1, 1983

By Thaddeus B. Evans

This information circular is one of a series describing mining methods and costs, being published by the Bureau of Mines. The Sunbright mine of the Foote Mineral Co. at Sunbright, Va., is the southernmost underground limestone mine in the State. It is a comparatively recent operation, and a description of its rapid development to production stage may have particular interest for the limestone-mining industry. ACKNOWLEDGMENTS Acknowledgment is made to the executives of the Foote Mineral Company including F. B. Shay, vice president in charge of production, W. B. Towner, general production manager; and to the members of the company staff at Sunbright for their assistance in preparing this paper.

Jan 1, 1957

By G. L. Neumann

In October 1949 the College Park Branch of the Mining Division instituted a survey of the New England pegmatites. Many of the New England pegmatite deposits were superficially examined, and the Bumpus quarry in Albany, Oxford County, Maine (see fig. 1), was selected for a diamond-drill exploratory-development project to supply information for developing more economical mining methods and no increasing production of beryl and other scarce minerals associated with pegmatitic intrusives. The Bumpus quarry has been mined intermittently by three operators since it was opened in 1927. At the time of drilling, the vein or dike (see figs. 2 and 3) had been mined to a depth of 60 feet for a strike length of 280 feet. The dike averages 40 feet in thickness and dips 50 degrees southeast. The Bureau of Mines drilled seven diamond-drill holes between September 27 and November 27, 1950. These holes showed that the dike persists for at least 350 feet to the east and probably 200 foot to the west of the present excavation. The drilling also indicated that the dip, as exposed at the surface, continued unchanged at 500 to a depth of at least 50 foot below the pit. The dike was not delineated, although it fingered out as pegmatite interbanded with Granite, diorite, and gneiss in diamond-drill hole B-4, approximately 250 feet west of the pit. Further drilling will be necessary to find the extent of this pegmatite dike and to determine the safest and most economic mining system.

Jan 1, 1952

By B. F. Naylor

"INTRODUCTION Investigation of the physical properties of electrolytic manganese and its alloys has constituted a part of the program of the Bureau of Mines for several years, and already extensive data have been reported. 3-14/ Heat-content measurements above 25° C. of pure manganese 15/ were completed recently at the Pacific Experiment Station of the Bureau, and the results obtained removed many of the inconsistencies in previously reported data. This paper reports heat-content data of seven manganese-copper alloys, varying in composition from 25 to 90 percent man-ganese. The alloys, obtained from the Salt Lake City Station, 16/ had been quenched from 850° C, and cold-worked. Without further heat treatment, heat-content measurements of each of these alloys were made at 100° or less temperature intervals from 450° to 850º C., as it was considered likely that any abnormal behavior of the specific heat would be found in this temperature range. Also, a portion of each alloy was heat-aged at given temperatures for periods of time thought sufficient to reach phase-equilibrium; then the heat-contents above 25° C. were determined at the aging temperatures. (Heat-aging was done at approximately 450°, 550°, 650°, 750°, and 850° C.)METHOD AND MATERIALSThe heat contents were determined by the ""drop"" method in a previously described apparatus. 17/ The calorimeter was cali-brated with electrical energy, measured in international joules, and the results were converted to the conventional thermochemical calorie by the relation, 1 cal. = 4.1833 int. joules."

Jan 1, 1946

By John R. Shattuck

Preliminary examination of the McCormick chromite property was made by the Federal Geological Survey and the Bureau of Mines during the spring and summer of 1943. In October 1943 an exploratory project was undertaken by the Bureau in cooperation with the Survey and was completed in February 1944.The urgent need during the war for high-grade lump chromite such as produced at the McCormick mine, was one of the pertinent reasons for the project. The McCormick mine is situated about 12 miles southwest of the town of Sonora, in the foothill belt of the Sierra Nevada Mountains, Tuolumne County, Calif. The chromite occurs as irregularly shaped lenses in masses of dunite contained in a steeply dipping, sheared, serpentinized zone of peridotite, near a contact with granodiorite.

Jan 1, 1949