Search Documents

By Frank E. Chase, John Rusnak, David Newman

During the past quarter century, coal mine geologists have evolved from providing a qualitative description of drill core and coal reserves into quantitative geotechnical specialists who bridge the gap between geology and engineering. In the late 1970’s and early 1980’s, hazard prediction mapping was in its infancy. At best, hazard maps identified rudimentary structures and conditions such as stream valley locations, sandstone/shale transition zones, and lineaments. A “technical disconnect” had existed between geologists and mining engineers as each profession operated largely independent of each other. Engineers did not readily integrate geology and geologic conditions, with the exception of coal thickness, into mine planning. Geologists were relied upon for reserve estimates and did not participate in mine planning or design. The employment and market slump of the 1980’s and 1990’s combined with mining more challenging reserves mandated that this gap be bridged and forced geologists to learn to speak more “numerically” to engineers so they could be understood. The purpose of this paper is to describe the procedures and thought processes used by coal mine geologists when determining various mineability and reserve extraction feasibility issues. The paper will also address underground geologic hazard mapping and prediction techniques. To achieve these objectives, the opinions and experiences of leading coal mine geologists, geotechnical and strata control specialists across the United States were solicited.

By Thomas C. Ruhe

The Bureau of Mines conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) saves energy, reduces oil imports, and reduces mining costs. Low ambient temperatures may cause these recycled oils to become too viscous for proper absorption by ammonium nitrate (AN) prills and result in poor blast performance, safety hazards, and environmental problems. To help quantify and resolve these issues, viscosity, mixing, and performance tests were conducted at various temperatures. Diesel fuels No. 1 and No. 2 were studied separately and in blends with 25,50, and 75% RO. Good quality ANFO mixes (94-6) were produced with dry absorbent prills and blended fuel (No. 1 diesel plus RO) at temperatures as low as -40°F (-40°C) with 75% No. 1/25% RO, and at -20°F (-29°C) with 50/50. Diesel fuel No. 2 also made good mixes as low as -30" F (-34°C) with 75% No. 2/25% RO, and at 0°F (-18°C) with 50/50.

Jan 1, 2008

By F. Cherpereel, R. Gabillard, J. P. Dubus

We present an electromagnetic method taken from the well known radiogoniometer that allows us to locate at the surface of the ground the vertical axis of a magnetic antenna transmitter buried at a depth h in the earth. The method and the equipment achieved are called R. E. P. E. (Relevé Electromagnétique de Points Enterrés). They are daily used to accurately survey old quarries by using triangulation instruments at the surface of the earth rather than in galeries where the setting difficulties considerably reduce their accuracy and increase the work length. The results of several surveys allow us to give the optimum working conditions of the instruments and show that, when the transmitter is at a 20 meters depth, its position is known at the surface with an error lower than 1 centimeter. The power transmitter is of about 8 watts and we can find its location with an error smaller than 1 meter when buried at a depth of about 100 meters. This equipment may be successfully used for location of subsurface miners. The space surrounding the transmitter must then be free from ferromagnetic bodies.

Jan 1, 1973

Decrease dust concentra¬tions of longwall face workers by keeping them up¬wind of the headgate stage loader and crusher. Approach Direct the face airflow from tailgate-to-headgate, the direction of coal transport. How It Works Ventilation is the primary method of dust control on longwall faces, and the most effective ventilation control is to put workers upwind of dust sources. Recent ad¬vances in longwall dust sampling by the Bureau have shown that on some faces, the headgate crusher and transfer points are signifi¬cant sources of dust -some¬times making up more than half of the total dust to which the face workers are exposed. Also, when the air is coursed from head-to-tail, the relative velocity between the air and moving coal on the face conveyor can cause dust entrainment from the conveyor, particularly if the coal is dry. On the faces where these dust sources are a signifi¬cant problem, they may be eliminated by coursing the air from tailgate-to-headgate, provided that the mine roof is stable enough to permit the necessary intake of the tailgate along with an aux¬iliary intake at the headgate.

Jan 1, 1982

Validate the premise that there is measurable seismic activity associated with abandoned mint lands and that this activity can be used to determine stability of the abandoned mine openings, failure cycle of these openings, and susceptibility of the area to surface subsidence. Approach The U.S. Bureau of Mines conducted field investigations at two geologically contrasting sites, Colorado Springs, CO, and the Allegheny Portage Railroad Historical Site near Cresson, PA, to demonstrate that developing monitoring technology can be applied to any site. An array of seven geophones (velocity-measuring sensors) were strategically located to encompass an area at each site where failure in the underground mine openings could be expected, based on historical, geological, and engineering information. How It Works Bureau research has effectively demonstrated that stress changes within a rock mass can stimulate the development of cracks and fractures, resulting in the release of strain energy that generates seismic waves. These seismic waves, traveling outward from their source, can be detected, and the point of origin can be located in three-dimensional space. Furthermore, these seismic signals contain information that defines the source mechanism and the conditions between the source and the receiving sensor.

Jan 1, 1992

Determine what diameter piping is necessary to obtain sufficient water flow to spray nozzles used for dust suppression. Approach A simplified, diagrammatic method of calculating the flow of water through a proposed system consisting of a supply line and two banks of spray nuzzles is outlined. How It Works The pressure versus flowrate of the supply at the tapping point must be known or measured. The supply curve of typical city water at a 1 ¼ -inch pipe outlet is shown by the lowest curve in Figure 1. A supply curve for a typical pump fed from an open sump is shown by the middle curve. The combination of these, the supply curve of a pump fed by the city water supply is shown by adding the lower two curves to get the upper curve. A pump supply curve showing flowrate versus pressure is usually supplied by the manufacturer. The water supply line flow curve can be determined by measuring the time required to fill a 55 gallon barrel at various valve settings to determine flow, and by measuring corresponding pressures at the valve with a gauge.

Jan 1, 1979

Predict the spontaneous combustion potential of a coal, using an expert system computer program. Background Approximately 15% of underground coal mint fires in the United States are attributed to spontaneous combustion. These spontaneous combustion fires frequently occur in worked-out or abandoned areas of a coal mine, This makes the control and extinguishment of the fire difficult and often requires large sections of the mine or even the entire mine to be scaled for long periods of time. A prior knowledge of the self-heating potential of the coal can be useful in preventing spontaneous combustion fires through the use of aggressive monitoring and control measures at existing coal mining operations, and in the planning oh new mines. Many factors can affect the spontaneous combustion process in a mine, including the self-heating potential of the coal, ventilation, geologic factors, and mining conditions and practices. Various test methods have been used to evaluate the relative self-healing potential of coals, including crossing point temperature and adiabatic heating methods, and oxygen adsorption techniques. However, these tests arc usually time-consuming and difficult to conduct, limiting their use to laboratories.

Jan 1, 1992

By S. B. Robertson, D. R. Dolinar, G. E. Hinshaw, G. M. Molinda, D. M. Pappas

Rock falls in coal mines cause many injuries each year. Most of these injuries are not caused by major roof collapses, but from falls of smaller rocks from the immediate top or roof skin. Even though safety professionals and mine operators strive to reduce these types of injuries, there has not been a substantial decrease in the rock fall injury rate over the past decade. Various surface controls are used in mines to control the roof skin. One control that has proven to be very effective is roof screening. Roof screen effectively controls roof skin and provides a high roof surface coverage. Although many mines are reluctant to use screen for primary skin control because of the additional costs of time and materials, others are having great success at controlling both the costs and surface rock. In this study, injury data are presented that show a dramatic reduction in roof skin injuries when screening is used. Much of this success is due to the protection from falling rock that the operators receive from roof screen. Five case studies in which roof screen was used are presented along with the associated costs of materials, impact on bolting advance rates, and potential ergonomic risks. The effects of roof screening on skin control and safety are also included. Finally, this paper provides information about best practices and features of roof bolting machines that affect production and safety.

By James W. Townsend, William H. King

"INTRODUCTION As a byproduct of its mineral investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the direct supervision of Paul T. Alisman, chief, Salt Lake City Division, Mining Branch, and under the general supervision of Lowell B. Moon, chief, Mining Branch, reports upon ore such technique.The Wright borehole-surveying instrument developed at the Homestake mine, Lead, S. Dak., has been described in several publications. 3/ For the benefit of those to whom the publications are not available, the instrument is described here. However, this article will be concerned mainly with the technique developed by the Federal Bureau of Mines for using the instrument.In the use of the Wright borehole-surveying instrument, it was found advantageous to develop a standard practice of operation covering type of film, preparation and care of film, loading film in instrument, placing instrument in container, exposure time, unloading film from instrument, development of film, and determination of dip and strike from film impressions."

May 1, 1947

By Thomas M. Barczak

This U.S. Bureau of Mines study evaluates factors that influence longwall support and strata interaction. The longwall system is composed of an immediate and main roof structure and three supporting foundations: longwall panel, powered roof supports, and gob waste. The main roof forms a structure that is generally supported by all three foundations, while the immediate roof acts as a beam that cantilevers from the coal face to the powered support. In most cases, shield loading involves a complex interaction of both main roof and immediate roof behavior and is a combination of loads produced from convergence of the main roof and displacements of the immediate roof caused by deformations of the cantilevered roof beam. Since the shield stiffness remains constant for all leg pressures and main roof convergence is irresistible in terms of shield capacity, the shield must be able to control the behavior of the immediate roof or floor structure for shield loading to be sensitive to setting pressures. If the goal is to minimize total shield loading, any active setting force must be offset by reduced passive shield loading to justify the active setting loads. Field data sumest that the typical reductions in passive loading do not justify the required increases in setting pressure in some applications.

Jan 1, 2010

By R. W. Stahl

"This study by the Federal Bureau of Mines was confined to pillaring with continuous mining machines and to mines where total extraction is practiced. Many different conditions and practices in as many coalbeds as possible in Pennsylvania were observed.Pillar extraction or pillaring can be the most productive part of coal mining if done properly; but it also can be the most dangerous if done improperly.Because of the need for more careful planning before and caution during pillaring, many mining companies resort to the undesirable practice of stumping or hogging of pillars with subsequent unnecessary waste of valuable natural resources. Pillaring can be done at reasonable cost and safely, as proven at many mines where complete extraction is practiced and enviable cost and accident records are maintained.Although continuous mining machines are bulky and sometimes difficult to maneuver, they have been used with great success in pillaring. Occasionally, however, a machine is caught, or men are injured by a fall during pillar recovery. This Bureau survey was conducted to ascertain how safe and successful pillaring (especially the removal of final stumps in lifts or the final stump of a pillar), is accomplished in some mines, while others have considerable difficulty under similar conditions.The Bureau hopes the information to be presented in this publication will prove beneficial to those who wish to recover more pillar coal and to improve their accident record during such procedures."

Dec 1, 1959

By L. C. IlsLey

The first thing to consider in prevention of electric shock is the voltage of the circuit. No person can be sure that he will not be killed, even from a 110-volt circuit, if he makes proper contact with the circuit so as to cause the maximum current to pass through his body. As the voltage is increased to 250 volts, 500 volts, or 2,300 volts the danger from contact with the electric circuit is increased, Alternating current of the same nominal voltage is possibly more dangerous than direct current. Experience has taught us that both will cause death, and that if the fatalities from this source are to be kept low, certain precautions in the guarding of circuits must be observed.

Feb 1, 1929

By James R. Coldwell

Mining and processing cost analyses were conducted by the U.S. Bureau of Mines on stratiform zinc-lead-silver, coal, and stratiform barite deposit types that are found in the Colville Mining District. Reserves and gross revenues which would allow these deposits to be minable were modeled. A 15% Discounted cash-flow rate-of-return economic threshold was selected as the minimum acceptable return on investment for the three deposit types. The economic modeling indicated combinations of grades and tonnages for stratiform sulfide deposits that could be economically viable for orebodies ranging in size from 25 to 130 million metric tons. The gross revenues for a surface mine range from $200/mt for a 5,000 mtpd operation using the proposed South corridor to $140/mt for a 17,000 mtpd mine using the proposed North corridor. The economic modeling indicated underground coal mining was subeconomic for deposits ranging in size from 42 to 250 million metric tons. The required gross revenues ranged from $300/mt for a 2,200 mtpd mine to $21 D/mt for a 13,000 mtpd mine. The economic modeling indicated supplying projected in-state barite demand was subeconomic for the three seasonal surface mines modeled. The required gross revenues ranged from $600/mt for a 90,000 mtpy mine to $840/mt for a 6,000 mtpy mine.

Jan 1, 1995

By Oliver Bowles

"A Product from Mica Mines.Mica commonly occurs in pegmatites which consist of large crystals of feldspar and quartz, mica constituting but a small proportion of the total rockMuch of the feldspar thus thro n out during the process of mining is pure and of high quality, end the Bureau of Mines has suggested that much of it could be utilized for ceramic purposes. Encouragement is given to such utilization by the fact that several mines now worked for mica were formerly operated for the production of feldspar. ""'here mines are not readily accessible to railroads feldspar utilization might not be feasible, for it is a much lower priced product than mica and cannot therefore bear as heavy transportation expense. '""here mines ire located close to railroads, however, such utilization would tend to reduce the cost of mica mining, and at the same time assist in the solution of the waste disposal problem.The Bureau has recently been informed that some of the feldspar from mica mines near Spruce Pine, N.C., is now being sold and shipped away. An extension of this by-product industry is to be recommended.A Mica Deposit in New York City.The Bureau recently received a mica specimen obtained from a. building excavation at 157th St. and Riverside Drive, New York City. The specimen was about 2 by 4 inches in size, and fairly clear though containing numerous hair cracks. It was obtained only 7 or 8 feet below street level. At greater depth and with more careful methods of excavation material of much better quality might be obtained. The material submitted could be used for mica washers but not for sheet mica. It is stated by an official of a prominent mica company that many such fragments are obtainable in this locality and the possibility of the occurrence of a good mica vein is thereby suggested."

Jun 1, 1920

By W. C. Phalen

"The Phosphate Rock Market:Indications, in the fertilizer market, point to a prosperous condition, caused chiefly by the growing demand for all classes of fertilizer material in spite of a shortage of supplies. Both of these conditions have been caused by the war. The shortage in phosphate rock is being relieved as production increases, but the supply has not caught up with the demand for this spring's trade, at least. Reports from Florida are to the effect that more than half the necessary quota of laborers are at work. This may not appear to be a very good showing, but even this situation is en¬couraging because there is a larger force now at work than has been the case for some time, and it is steadily, though slowly, increasing. Some of the producing companies are conducting advertising campaigns to get laborers back to the phosphate fields and attractions in the way of better housing and living conditions are being offered.Producers are far more confident about the situation than they were two months ago, and though the shortage will not be met before the end of 1920, theme is a surplus accumulating over what is going out on existing contracts.Quotations are now being offered on all Florida rock excepting land pebble and this, it is expected, will be soon quoted.Quotations on Florida rock per ton are as follows:"

Jan 1, 1920

By Chas. F. Jackson

The annual reports of the supervising engineering of the nine sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim is to adapt them to changes in conditions, in the needs of the mining industries, and in the public interest; those current activities that contribute most to problems of present concern are emphasized, investigations of less immediate importance being recessed, if necessary.

Jan 1, 1940

By Chas. F. Jackson

The annual reports of the supervising engineers of the nine sections comprising the Mining Division are assembled in tie following pages and constitute the annual report of the division. In planning activities, the aim is to adapt them to changes in conditions, in the needs of the mining industries, and in the public interest; those current activities that contribute most to problem of present concern are emphasized, investigations of less immediate importance being recessed, if necessary.

Jan 1, 1940

By D. Caruso

The health and financial costs of cumulative injuries are plaguing the mining industry. Industry leaders are concentrating on reducing the risk of injury to their workers through design and redesign of work environments. While ergonomics is not a currently regulated field, many mines are realizing that the only way to tackle their most costly injuries, cumulative injuries, is to make the proactive choice to understand those injuries, their root causes and to make workplace changes to prevent them from occurring. Reduction of these injuries not only improves the health and morale of the workers but increases productivity and profit for the companies. Knowledge and reporting of ergonomic risk factors by employees and ergonomics committees is key to these changes and to the reduction of cumulative injuries. NIOSH is developing strong relationships with industry associations and equipment manufacturers to leverage their communication abilities to transfer knowledge to their customers and make a difference in the health and safety of U.S. miners. The benefits of a formalized approach to reducing these injuries along with examples will be presented.

By N. H. Coates

As part of a joint program of the U.S. Atomic Energy Commission and the Federal Bureau of Mines for using nuclear energy to supply process heat, the Bureau designed and constructed a pilot-scale simulated nuclear reactor system. Although workable components were developed,5 the simulated nuclear reactor could not be operated continuously at its design conditions of 2,500°F. and 250 p.s.i.g. because the refractory materials used for insulation deteriorated. Replacement of these materials with porous carbon permitted sustained operation at design conditions, and a 1,000-hour demonstration run was completed successfully. No serious operating difficulties developed during the test. Leakage of helium after 1,000 hours was only 3 to 4 std. c.f.h. Inspection after the run revealed no damage to any of the components. Including earlier runs during previous research5 the system has been operated about 4,000 hours, of which 1,120 hours have been at 2,500° F. or higher. The helium-recycle compressor performed satisfactorily with no main¬tenance whatever for 2,445 hours, with about 2,000 hours at 900° to 1,000° F.

Jan 1, 1961

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel.oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which typo of plant utilizes more thou the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which crude oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining. Although no outstanding technical developments of a fuel-saving nature were made in 1934, some progress undoubtedly was recorded. Heat exchangers, an effective fuel-saving device, wore enlarged, and some refiners now take off several cuts before the crude reaches the pipe stills. The total capacity of pipe stills increased 2.5 percent in 1934, and many of the less efficient shell stills were torn out.

Jan 1, 1935