Search Documents

By A. C. Johnson

The Ellington manganese deposit in Reynolds County J Mo., had been known for some time; and limited exploration, consisting of test pitting and sinking a shaft 54 feet deep on the property, had been done by private interests. Late in 1941, the Bureau of Mines cleaned, deepened, and sampled many of the existing pits and dug and sampled 27 new ones. The shaft was unwatered and sampled, and several pockets of manganese ore were trenched to determine their extent. Samples were analyzed and beneficiation tests on 1 ton of the ore were made at the Rolla, Mo., station of the Bureau of 'Mines. Results of the investigation indicated that the deposit was small and low in manganese content.

Jan 1, 1948

By David E. Siskind

The Bureau of Mines has studied the fracturing produced in the vicinity of large-diameter blastholes in Lithonia granite. Cores were taken from the vicinity of AN-FO production blasts and examined using a total of seven laboratory and field measurement techniques to delineate zones of damage and evaluate the effectiveness of the seven diagnostic tests for fracture-state determination. Laboratory measurements of acoustic pulse velocity, porosity, permeability, compressive strength, and Young's modulus indicated the extent of fracturing with the acoustic techniques providing the best means of distinguishing between fractured and unfractured core. A severely fractured zone was found to extend approximately 25 inches (64 cm) from the center of the 6-l/2-inch blastholes, equivalent to 8 blast-hole radii. A second zone, characterized by a lesser degree of fracturing extended from 25 to 45 inches (64 to 114 cm) or 8-to l4-blasthole radii. Beyond 45 inches (114 cm) the rock was undamaged.

Jan 1, 1974

By B. M. Bench

This Bureau of Mines report describes photo lineaments obtained from stereoscopic examination of vertical aerial photographs and by the Ronchi grating study of aerial photoindex sheets. The photolineaments are compared with the trends of oriented fracture systems procured by measuring the compass direction of joints in bedrock. The relative reliability of the methods is shown, and the results are presented in graphical, tabular, and written form. Analyses of field measurements of strikes of bedrock joints in the project area indicate for the most part two intersecting sets of major joints oriented N 76° W -N 15° E, and N 57° W -N 27° E. The analyses of lineaments determined by stereoscopic examination of aerial photographs show dominant trends of lineament zones of weakness to be an average of N 65° W -N 20° E. Analysis of lineaments found by Ronchi grid viewing of aerial photoindex sheets indicate dominant trends of N 70° W -N 27° E. The three methods give similar findings and verify the work of previous authors. The Ronchi grid method is a useful guide, but it cannot be substituted for the two more painstaking methods.

Jan 1, 1977

By Jacob N. Frank

A factorially designed, hydraulic fragmentation experiment using a high-pressure water jet was conducted on concrete blocks. Three levels of pressure, standoff distance, and impact angle and two levels of traverse time and surface condition were used. Three variables were measured: depth of penetration, volume of material removed, and width of slot. Three stepwise linear regression equations were developed from the jet parameters and the physical properties of the concrete. The three basic equations, describing the significant jet parameters and physical properties, were developed into 15 predictor equations, five for each variable investigated. Direct regression equations were also developed for each variable investigated to show the result of increasing or decreasing each significant variable. Energy efficiencies were developed for the experiment and for each significant factorial variable.

Jan 1, 1971

By Arnulf P. Hagen

This project was designed to explore the suitability of using fluorinated inorganic materials as solvents for the in situ mining of thin seamed, heavily overburdened coal; to build a data base for the selection of an inorganic solvent for use for coal cleaning; to determine if fluorinated solvents will reduce the organic and inorganic sulfur contents of the coal, as well as to lower the ash content. The coal samples have been combined with pure solvent, as well as with aqueous solutions at atmospheric pressure and at increased pressure. The increased pressure experiments are important since they duplicate the conditions anticipated for an in situ cleaning and mining operation. Trifluoroacetic, difluorphosphoric (phosphorodifluoroidic), and trifluoromethanesulfonic acids have been found to be effective for the cleaning of high sulfur, high ash coal at 300°C and at atmospheric pressure. At pressures up to 20,000 psi the effectiveness of these reagents is not decreased.

Jan 1, 1983

By Wilbur I. Duvall

Nineteen quarry blasts were instrumented with particle-velocity gages mounted in a uniform soil overburden, back of one face in a quarry in Iowa. Three components of particle velocity, radial, vertical, and transverse, were recorded at each of eight stations back of each blast. Distances from blast area to gage stations ranged from 150 to 3,000 feet. Eleven of the quarry blasts employed millisecond delays, and eight were instantaneous blasts. Charge weight per hole was 200 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 100 to 3,000 pounds. Analysis of the data from these tests shows that the particle velocity, V, produced at distance, D, by a quarry blast of charge per delay interval, W, can be represented by an equation of the form, V=KWb D-n, where b and n are exponents, and K is the intercept constant which is a measure of the level of vibration. The value of K for a millisecond-delayed blast employing one hole per delay interval is about 42 percent larger than the value of K for a single-hole blast. The value of K for a multiple-hole milli-second-delayed blast is about the same as that for an instantaneous blast when the charge per delay for the millisecond blast is equal to the total charge for the instanteneous blast. The vibration level from millisecond-delayed blasts employing one hole per delay is shown to be independent of the length of the delay interval and the number of delay intervals over the range of the variables tested: 9, 17, and 34 milliseconds and 3, 7, and 15 delays per blast.

Jan 1, 1963

By F. W. Cox

Exhaust emissions were measured from 25 aircraft turbine engines using Jet A fuel. Analytical apparatus, procedures, and results are described. Carbon monoxide, carbon dioxide, nitric oxide, nitrogen dioxide, and aldehydes were measured at engine operating modes representing power levels used in airline operation. Carbon monoxide, hydrocarbon, and aldehyde emissions were highest at idle and lowest at takeoff; oxides of nitrogen were lowest at idle and highest at takeoff. Of the total oxides of nitrogen emitted, nitrogen dioxide constituted from 10 to 100 pct, depending on the exhaust gas temperature. Engines retrofitted with smoke-reducing burner cans produced less carbon monoxide, hydrocarbon, and aldehyde emissions, and slightly more oxides of nitrogen then engines with standard burner cans.

Jan 1, 1972

By Jeffrey B. Osmint

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1991

By P. G. Clites

This study was conducted to determine the patterns of heat transfer to water-cooled copper crucibles during vacuum arc melting. Values of heat flux from the ingot to the crucible were determined during nonconsumable electrode vacuum arc melting of zirconium and during consumable electrode vacuum arc melting of titanium) zirconium) and steel. The results of these studies con-firm the existence of a high thermal resistance between the ingot and the crucible wall which results from the shrinkage of the ingot as the metal solidifies. Maximum heat flux occurs near the top of the ingot where maximum values of heat flux of 1.4 X 106 Btu/ft2 hr were observed during small-scale consumable electrode arc melting of zirconium and titanium. The maximum heat flux for consumable electrode arc melting of 8-inch-diameter ingots was 0.5 X 106 Btu/ft2 hr. The effects of electrode material) electrode diameter) arc current) and arc potential on heat flux from the ingot to the crucible were studied. Data were also obtained on crucible wall temperatures and on the effect of very narrow annular water jackets.

Jan 1, 1967

By A. L. Engel

Included in the program of the Rare and Precious Metals Station, Metallurgical Division, Bureau of Mines at Reno, Nev., are investigations of treatment methods for ores representative of various mining districts throughout the country. The samples received for this work may come from areas only recently explored or from newly discovered ore deposits in older mining districts. The present investigation deals with a case of the latter type, the. ample having come from a section that has a past record of considerable precious. metals production. The application of current treatment methods to this type of ore seems to offer excellent possibilities of satisfactory economic results. Definite identification of the silver mineral in this ore asthe chloride cerargyrite, AgCl, adds considerable interest to, the investigation, as in many cases where silver occurs in comparatively small amounts in an ore it is not possible to identify the particular mineral carrying the silver or else it is contained in or combined with other more common minerals. Cerargyrite is the "horn silver" of the bananza period and is mentioned in many accounts of pioneer mining of high-grade ores The occurrence of this mineral in finely disseminated form it a low-grade ore is believed to be unusual. The sample investigated was obtained from the' Bullfrog District neat Beatty, southwest Nye County, Nevada. The ore contained 16.7 ounces of silver per ton of ore, 0.007 ounce gold, and 0.32 percent copper in a silicious gangue, with accessory minerals, including iron oxides and scorodite; the hydrous iron arsenate.

Jan 1, 1949

By Stephen C. Brown

The major developments of the world's Mineral economy in 1955 were the continued rise in production and consumption of practically all major minerals. the sharp increase in output of the fertilizer minerals in response to demands for greater food output, the cutback, in new investment for steel capacity in Europe and Japan, Europe's continuing decline as a producer of primary minerals, and the emergence of nuclear power as an economically competitive factor in the energy economies of the United States and Western Europe. In resource development, discovery of new natural gas deposits in the North Sea and the continued development of Australia's bauxite and iron ore resources, making this country a major source for these commodities, were significant.

Jan 1, 1967

By Michael J. Sapko, Eric S. Weiss, Kenneth L. Cashdollar

A fundamental safety research area for the National Institute for Occupational Safety and Health (NIOSH) is to eliminate the occurrence of coal mine explosions or to mitigate their effects. One approach is to develop and evaluate new and innovative seal designs that provide increased explosion protection for mining personnel. The NIOSH Pittsburgh Research Laboratory (PRL) cooperated with HeiTech Corp. of Virginia, Barclay Mowlem Construction Ltd. of Queensland, Australia, and the Mine Safety and Health Administration (MSHA) in three separate research programs to evaluate the strength characteristics and air leakage resistance of numerous innovative seal designs and ventilation control structures for use in underground coal mines. For each phase of the program, various full-scale seals, stoppings, and an overcast design were constructed in PRL's Lake Lynn Experimental Mine near Fairchance, Fayette County, PA. The seals and stoppings were built in crosscuts and were subjected to explosions to evaluate their strengths. Four pumpable cementitious seal designs ranging in thickness from 610 to 915 mm (24 to 36 in) were evaluated in the first cost-reimbursable research program with HeiTech Corp. A simple wooden framework with brattice liner was used as a form to contain the cementitious slurry during the curing period. As the seal designs decreased in thickness, higher compressive strength cementitious grout was used. All four seals withstood an explosion pressure pulse of at least 138 kPa (20 psi) while maintaining acceptable air leakage resistance. In the second cost-reimbursable research program with Barclay Mowlem Construction Ltd. of Australia, several innovative seal and stopping designs and an overcast design were evaluated. Each of the seal designs and the overcast side and wing walls used one or more air-inflated vinyl bladder assemblies anchored to the mine roof and hitched into the ribs and floor. The air within these bladders was displaced with a high-strength cementitious grout. The overcast deck consisted of a 200-mm ('7.8-in) thick reinforced cementitious slab. This was the first time that an overcast structure had been explosion tested under full-scale conditions. All of the seals, stoppings, and overcast design passed the air leakage tests before being subjected to a series of explosions with static pressure pulses ranging from 14 to 475 kPa (2 tab 69 psi). Instrumentation measured seal and overcast wall displacement as a function of time. The 450-mm (1 7.7-in) thick seal in the 2.8-m(9-ft) high third crosscut withstood an explosion pressure of 170 kPa (25 psi), but failed during a later test, which generated a peak static pressure of 475 kPa (69 psi) at the seal location. A similar 450-mm-thick seal in the 2.1-m (7-ft) high second crosscut withstood three explosion tests, which generated peak static pressures of 195, 205, and 370 kPa (28, 30, and 54 psi) at the seal location. Next, the overcast design withstood four explosions, which generated static overpressures ranging from 16 to 47 kPa (2.3 to 6.8 psi). A third program at the request of MSHA evaluated the effectiveness of using pressurized grout bags (Packsetter bags) along the mine roof and ribs in lieu of floor and rib hitching for a standard-type solid- concrete-block seal. This program was initiated to address an urlusual geological mining condition encountered when building seals in entries where required rib hitching is not a viable option due to soft friable coal. Results showed that the use of these quick-setting grout-filled Packsetter bags pressurized internally to 300 kPa (44 psi) not only provides a seal that can withstand a 138-kPa static pressure explosion, but also provides a sealing option where rib hitching is not possible.

Jan 1, 2003

By Edward F. Divers

This Bureau of Mines report describes the results of a program to develop small, rugged scrubbers with high dust collection efficiency for use in under-ground coal mines. The Bureau's Pittsburgh (Pa.) Research Center has developed and assisted in the development of several types of improved scrubbers that are especially suitable for various underground mining applications. Research efforts concentrated on reducing the size, power, and water consumption of these scrubbers, while optimizing their dust collection efficiency. Fractional dust collection efficiency, air volumetric range, size, power, water consumption, and application guidelines for each type are described. Air pressure differentials ranged between 2-and 3D-inches water column (wc). The dust collection efficiency of six scrubbers--a venturi, two flooded-fibrous-bed, a venturi-impaction plate, a wetted-fan, and a rotating flooded-bed--were compared. The rotating flooded-fibrous-bed and the stationary flooded-fibrous-bed scrubbers showed the highest coal dust collection efficiency. Test results show that these scrubbers can generally achieve respirable size coal dust collection efficiencies in the high 90-pct range required to reduce both long-(8-hour) and short-term coal mine dust concentrations below Federal requirements.

Jan 1, 1979

By H. C. Howarth

The preliminary tests referred to in this report wore made at the Bureau's Experimental Mine under the general supervision of G. S. Rice chief mining engineer, to determine whether rock dust way be used to extinguish or control mine fires. DESCRIPTION OF THE DUST USED The dust used for application by hand was made from draw slate taken from the Experimental Mine. This draw slate was crushed in a hammer-type crusher fitted with 1/16 inch by 2-inch slotted screens. A sizing test of the dust showed 96.5 per cent through 20 mesh, 69.4 per cent through 48 mesh, 46.2 per cent through 100 mesh, end 33.5 per cent through 200 mesh.

Jan 1, 1927

By J. E. Murphy

Field freezing was used by the Bureau of Mines to effect the redistribution of the components in a cerium-12.5-atomic-percent-iron alloy. The application of the electric field caused the iron to migrate toward the anode. A field intensity of 0.04 v/cm and a current density of 240 amp/cm2 were used. The conditions that yielded the greatest redistribution of alloy components were a small thermal gradient along the specimen (from 5° C/cm to 10° C/cm) and a very slow freezing rate (0.15 cm/hr). Under these conditions it was possible to process specimens of ½ -inch diameter as compared with the capillary-size specimens used by most previous investigators.

Jan 1, 1968

By E. P. Youngman

The law of June 5, 1911, suplements and amends the Laws of April 21, 1810 (the basic law) and May 2, 1837. The Royal Decree of September 15, 1919, coordinates the provisions of the Law of June 5, 1911, with those of the Laws of April 21, 1810, of May 2, 1837, and of July 8, 1865, that have remained in force, as well as with certain articles of the Law of September 1, 1913, which revisad the system of taxation. The revised code has been brought together in one volume.3 All citations in this abstract refer to the coordinating Royal Decree of September 15, 1919, unless it is otherwise specifically indicated.

May 1, 1930

By L. A. Haas

The degree of reduction of various silica-graphite mixtures was studied in a batch reactor to determine optimum physical conditions for maximizing the carbothermic reduction of silica. The extent of interaction was determined for reactant mixtures in loose powder and briquet forms at pressures less than 0.01 torr and temperatures up to 1,445° C. Molar ratios were varied from 0.05 to 6.5 with maximum reaction at a ratio of about 1.5. The solid-solid reaction did not appear to involve gaseous intermediates. The extent of reaction better correlated with the number of interparticle contacts than with the true surface area of the reactants. Carbonized dextrose was a better reductant than graphite.

Jan 1, 1968

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

A.5 Conclusions and Recommendations The illustrative simulations in the previous section have demonstrated 1. Flexibility of the program to simulate a wide variety of configurations and cases. 2. Ability of the program to predict evacuation time within a small margin of error (5 percent -.n a case considered). 3. Usefulness of the program in making some of the evacuation decisions. The above leads to a conclusion that the computer program can provide a useful tool in evaluating mine evacuation in the event of a fire. At present the program can be used to make decisions regarding evacuation scheme improvement, while the scheme is being studied. However, significant software and hardware developments are

Jan 1, 1976

1. In 2001, a total of 281 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA) (down from 309 metal mines in 2000). Metal mines were the smallest mining sector, 1 comprising 1.9% of all mining operations. This was the lowest percentage of all mining sectors. • The median number of operator employees per metal mine was 17.5.2 • Gold mines comprised 43.1% (n = 121) of all metal mining operations. Other types of metal mines were copper ore (n = 37, 13.2%), iron ore (n = 27, 9.6%), and lead and/or zinc ore (n = 24, 8.5%). • Nearly 20% (n = 55) of metal mines were located in Nevada.

Jul 1, 2003

This is the final report on Project CR-102 under the auspices of the Department of Environmental Resources, Commonwealth of Pennsylvania .1 The project was activated on January 5, 1970, with financial support from Bituminous Coal Research, Inc., the Pennsylvania Coal Research Board, and the Water Quality Office of the Environmental Protection Agency (WQO-EPA)2 through Grant 14010 EST to the Commonwealth of Pennsylvania Work on the project was conducted according to the procedures outlined in BCR Research Program Proposal RPP-164R, dated April 24, 1969, and a subsequent Revulsion of Scope, dated February 25, 1970. This report covers the entire project period from January 5, 1970, through March 25, 1971.

Jan 1, 1971